DIY Electric Bike - Power assisted bike at home

[@America_Yea]

Bit of a tip from an electrical engineer you might wanna mesh the copper wire on your solder joints for less electrical resistance on your circuit you always want direct copper to copper contact if at all possible or your connections may heat up at the solder joints on high energy circuits like this and melt your solder apart or start a fire. Of further note you might also heavily waterproof the battery leads and any other open connection to prevent potential electrocution in the rain or during even standard driving sometimes, we almost always add a plastic shell to applications like this as an errant car or bike may splash you with lethal results at any time though spray rubber or even electrical tape would be enough for most short term wetting though I'dreccomend a coating of resin over it if you tape it.

[@America_Yea]

The potential solder joint heat issue can be checked with a thermal camera to see if your draw has issues under heavy load(check while riding or on test stand with the maximum liad on the bike) just look for a hot spot right where the join is.

[@diarmaidok]

Looking at this critically I'd say it is a death-trap the belt drive on the crank meaning always spinning cranks and pedals the high risk of clothing catching on the belt driving the crank or fire or electrocution...I'd rather just use an unassisted push bike.

[@sumanjit100]

That man has everything he needed... it will be heaven for me to hav a store room like him...🤗

[@WahyuMairadi-cd1ix]

Jarang ada orang yg berbagi ilmu seperti beliau. Dari idenya beliau bisa jadi suatu pemasukan atau pekerjaan yg menjanjikan.. terus berkarya bro,..

[@canerandagio104]

This time you've failed,the crown welded directly on the pedals is a wrong idea,in my opinion.

[@sukmayatamang6764]

0000000000000000000000000000000000

[@umarsaleem8638]

Exactly

[@binuthdulnaka1153]

It have to crown on to the free wheel backside

[@bradmason4706]

I've tried 3 or 4 different controllers and throttles and none of them work as a gradual increase in power is Just an on off switch. Which should be connected to the brake so that it turns off the motor when you apply the brake

[@suyadiuya6965]

Nice video. Replace Your small pedal gear with a freewheel gear(like rear gear) will help You when You will use/operate mode : pedal only, motor only, or both. It will make Your leg safer & more comfortable

[@buynsell365]

OMG !!! That is a very beautiful place you are riding..........loved the build......works great.....just need to find a way to disable the pedals when in power mode......I would love to try this myself.

[@turbanatortech7914]

Everyone else : buys expensive kits. This guy: has everything😎😎

[@snobirirfan3389]

Great Yar. Where from u.u show great humanity.poor people cant suffer more.

[@perfectwayi4789]

Brother i am from india You always helpful for me🤗 Thanks

[@সাইফুলমজুমদারবিজনিছ]

ব্যাপারটাতো খুব মজার! ভালো লাগলো 👍👍👍 hahaha

[@MrBrymstond]

I think it would be best to install a long chain to a certain small sprocket in the back so the peddle doesn't get you hurt.

[@bradmason4706]

those motors have resistance to peddling.

[@shiranianfamilyj-pack6230]

This guy can really build everything....

[@hutao7324]

Creative channel congratulations to 1million subscribers I am one of them

[@manuelfloressr.9039]

You need a freewheel on that pedal crank. I like the skills, it looks like you have done this a couple of times, congrats!

[@bansidharswain5359]

Biafr

[@62_priyanshsingh6]

What does free wheeling mean? Does that mean pedals may stop while the motor still continues to power the wheels? How can he add that?

[@anmoldatar5787]

@@62_priyanshsingh6 he arranged that fix wheel with the help of cuts and threads.. instead of that he can use free wheel. Free wheel helps to, use the motor power to wheels without using of padels...

[@62_priyanshsingh6]

@@anmoldatar5787 Thanks ☺️

[@shivpartapkansal5674]

Its a great video for cycle lovers they will know how to make a simple cycle a electric bike good. Well done.

[@mahmoudmohammed6785]

It's a funny way how you ride the bike but I like it and I like your idea about making an electric bike. Keep up I'll watch all your videos from here on and good luck my friend.

[@AB-re6re]

BETTER than walking 😁✌️

[@lifeyang2]

You need to get the pedals to work independently from the motor.

[@SunilKumar-bv5ci]

N

[@yeer31]

Absolutely! Those flailing pedals are a potential disaster waiting to happen. This is an extremely irresponsible build.

[@xpd.8262]

@@yeer31 not irresponsible but I see you're point, it would be much better

[@conceitosdetesla1841]

👍👍

[@bojackson3073]

@@yeer31 i imagine he would peddle with the bike, it's the chain thats now a hazard.

[@Jershan_biju]

This is absolutely a creative channel

[@bodean5163]

Great simple build but it needs a clutch or ratcheting sprocket between motor and the pedals.

[@johnaustinbenavidez865]

Hi. noob question sorry. What is the function of clutch or ractcheting sprocket if added in this setup?

[@yoenndelatrinite0684]

Tes pas bien moi même je n ai jamais pensé sa

[@ประนอมรอดพานิช]

รแตดคิตเ บอกให้หลับดีๆหน่อยดิว่าพี่จะทำสกูตเตอร์ทำจักรยานไฟฟ้าได้ไง

[@tatylima9948]

1 1h uf eudhc d dbbd d

[@tatylima9948]

Kekdkdiwkwktmlxms

[@dannydmv5341]

Chao em, anh hay coi em da lau va thich cach lam cua em, rat pro ,like cho em nhieu, va xinh loi vi nhieu clips ko de like , 👍1111111111

[@muhammadalibhaijaan5713]

Thanks for share with me and I love this video

[@anka-go4024]

semakin creativ aja om kuh,.,. terimakasih video info dan tutoriALNYA

[@sanjayrajak6441]

Whdhdgd🔰❇Ⓜ🌀✅🎾🏸🏒🏹

[@barisoww1385]

Very good I'm turkey

[@kingkorasawasaki6620]

What a creative man. good work keep it up and thanks for the idea anyways 😁👍

[@lrakyesdnil6360]

You should create safe guard for chain in case of injury

[@nosadkhan7080]

Cdijoy

[@Adnan-kg4cj]

What to do if the battery charge is over.can we charge it.

[@7777-i1h]

Хорошо. Но требует доработки. Шатуны с педалями не должны крутиться при работе мотора

[@sujisujisuji8814]

88b(

[@ariyan3526]

Keep cooked big difference

[@hymlog]

...just happen to have all that stuff. ...Let me get on this Right Now!!

[@gururajeshmurarishreebalaj6573]

Bhai manngya Mere pass ye he cycle hai and Mai ye he shundh Raha tha kaise bhi Mai aisi bana shku ki paiddel se bhi challenge and moter se bhubthnx Bhai thank u so much love you bro

[@wasimqureshi2994]

I think you should connect motor chain direct to rear wheel🤔🤔

[@easywebsolution7044]

Yes, he add motor wrong place

[@louiegeorgesupetran4635]

It's called pedal assist bruhh

[@mdansarmohammad2055]

Sakte hain vah cycle kitne paise Unse Liya Hai Kahan Se liye hain

[@bobconstantino5179]

I suggest putting the power sprocket on the other side (pedal plate side) and use a more longer chain driver so as to utilize the free wheeling of the plate.

[@Rob337_aka_CancelProof]

I would love to see a 6-month review on that because that's a very simple DIY mid-drive and you just can't beat the mid-drives so if it stands the test of time actress good and broken in and still running effectively I might try something like that myself thanks for the idea

[@hishamm.s3370]

But the video was awsome 👏👏👏👏👏👏👏👏👏👏👌👌👌👌👌👌👌👌👍👍👍

[@gurughantal6079]

Only one question, how to protect the motor from rain, is motor water proof ?

[@UsmanGhani-c3j]

Yes it is

[@Mustangrocket98]

Very cool bike dude i might go to my local walmart and get bike but i want mine to be in black and either install 2 stroke engine or maybe make it electric

[@sausagefingers714]

basically the e-bike equivalent of a fixie.. its one way to destroy your legs. its really important to have a clutch man!

[@yagnapatel6664]

aweson video, but DAYUM that pinky nail

[@abhishekkadam3378]

You should remove those big rods of the pedals but awesome work

[@daviddicker7025]

Electric bikes don't work like this!! How can you have your feet on the pedles at full speed

[@jboy27]

Well if u watched the video he does not have his feet on the paddles when it's in use

[@daviddicker7025]

@@jboy27 I did watch the video and being an engineer I can see that this is very badly designed.

[@kaptein1247]

David Dicker, yeah. This guy isn't the smartest.

[@metalheadmalta]

Absolute madness.... one hit of those pedals on your ankle, and it's sayonara sucker...

[@kaptein1247]

David Dicker, you dont need to be an engineer to see that btw.

[@abdullahcankurt5588]

Helal sana bu projeyi bende yapacaktım tebrikler

[@sofianesofiane3370]

Pĺ0

[@fingertipideas]

Motor should not move the pedals

[@gmolopez4056]

Of course.

[@yairbeker3983]

So good! Nice job! Jost pls link for the buttary

[@shweshwe3189]

יאיר בקר ဲ႕

[@nagenderannagenderan2650]

@@shweshwe3189 gj

[@rajmulay4062]

nicely don ... please provide link for sprocket and gairs you used..

[@eidBike]

Bravo you are an artist in this good work on the installation of motorcycle in our cars in our channels the same motor in the loop back and front, as well as a fan in the bicycle repair channel and tell you Bravo you and you a good greeting

[@Ranjankumar-yz3rg]

Hi I followed your method and made electric cycle but speedof my cycle is 7 km/hr and once charged give only travel 6 to 8 km. Pls help

[@user-xt7cs6sh5i]

just use more power

[@kamranmurtaza6937]

ALA cousin i have your same problem

[@paulevans4334]

Guys you need to use lithium battery cells

[@NG-zg8vf]

You need better batteries, use 18650 cells, try to make at least a 20amp battery pack and hey you better off walking if it only goes 7km an hour

[@krishdevkar6352]

The best video in my life

[@BeaverBaister]

I hope you can pedal fast. I'd put a clutch in. Otherwise good job

[@ALEJKDARK]

it is better to have the engine gear for the rear wheel as it is normally done so you can accelerate and you will not move the pedals in an uncontrolled way

[@NiteshKumar-ls4sg]

Kahan par banti hai bhaiya Sahi ke liye

[@julianalejos5529]

la mayoria del trabajo esta bien pero necesitas instalae un rache en la corona del lado del motor

[@karthiksarada2656]

The paddle gonna hit your leg if u dont keep up your paddling speed . Better connect motor to rear gear .

[@salmahady5993]

٠

[@sabyaking890]

Bhai so thank u for upload this video.so thank u

[@Rob337_aka_CancelProof]

How does it shift under load with somebody on it? That's the thing that makes mid drives great you can use the existing gears and it's not a pain in the ass to change a tire

[@ianatolij500]

Привет! Молодец.9/10

[@matiasarganaraz5974]

Good bike!

[@brokenmusic07]

Ess kai pydal nikaal dooo or pairuw kai leyai koyii jaga Bana doo....pir acha lagai gaa....bakii saab acha hai very good

[@dj.marquinhosdevoltaaopass2438]

Pode me dizer quanto quilometro fez com uma garga autonomia da baterias e de quantos amperes você usou

[@manuau5096]

99or or i888888

[@TexnikKOB]

make an overtaking clutch with the help of rear wheel stars and set forward on the pedals so that the feet can not be raised from the pedals

[@alessiopozzebon7082]

TexnikKOB ciao

[@PhoenixPhantasyYT]

You have to make additional gear so you don't have to lift your legs on the bicycle frame it might hurt you You can use the back gear concept for that it's very easy

[@sobesao6477]

or just install a free wheel on the pedal

[@dailylife6770]

You should've install freewheel sprocket instead of fixed sprocket.

[@nagmasports1400]

Which is the best. This one or the blue magnum fat bike,of another video.

[@veraluciallanosrivero9207]

Megusta el vídeo soy fan #1 quiero más video

[@veraluciallanosrivero9207]

Hola soy Cristian soy fan #1

[@caiocflegends7875]

Bike name?? Pleaseeee, this bike is amazing and beautiful!!!!

[@shoraimheshami4120]

Jaguar fat bike Available on amazon Price 14999

[@narayantripathy2980]

Hu

[@surendersingh-vn6xf]

How many price of this

[@НурмухаммадА-с1б]

Шу8щ рахмат рахмат кизим 678488883843993999938938щкллалеллелнллеллеллеееееееллееееееле

[@gamerarab8558]

@@НурмухаммадА-с1б ٠٠ 0ش

[@Rob337_aka_CancelProof]

The adapter you put on four I think it was power with a black heat shrink that was oversized you can slip a couple of pieces of hot glue inside of there before you shrink it and it will waterproof that connection for you put enough in so it's squeezed out by the heat shrink as it shrinks and then just trim off the remainder that's sticking out. Hot glue and heat shrink work great in combination

[@ALSmith-zz4yy]

You can buy simple kits that mount these motors at the back of the frame near the rear axle. Why risk putting it at the cranks where you can get shoelaces or a pant leg caught in chain?

[@MyUnknowing]

why buy kits, when you can build your own, more fun 100%

[@ruzokedits]

who will control the pedals ?

[@saurabhjaiswal3039]

While running moter we free paddle, you need to fix this problem also...rest every thing is perfect...

[@jadrianomarques82]

Parabéns, ficou muito boa, que motor é esse que você usou?

[@marcosradix1]

You are incredable, where I can buy this kit ?

[@mapuiimapuii5775]

Đygvkjc hhbnlkse fungsddh guhuftdgibihhs hhogr gxngj ve difhhfh ggcsub ghhuhdrugģyfh

[@stanrezong7225]

His warehouse reminds me of Doraemon's pocket......😇

[@joaomuniz070]

Foi uma ótimo ideia so falta adquirir um jeito pra os pedal parar de girar

[@joaopedrosimoesdeandrade7773]

kzbin.info/www/bejne/aaLNf4ykj5mSZtE Esses resolveram. Tem algum tipo de catraca no eixo do pedal, assim como as engrenagens traseiras das bicicletas que só respondem ao torque em um sentido.

[@mdshmjp5763]

I need one. How can I take it?

[@billrimmer5596]

Really cool! U r very talented!!

[@clementamama8472]

i like it, but i dont like the part with pedals spinning and your legs hanging up when you switch to electrial cycling mode, just change the position of the motor

[@spectrfox7661]

There are a lot of ways you can change the position of the motor, but that isn't really the problem, it's also a safety hazard (because of the chain there) but the main problem are the pedals, since the chain from the motor is connected to the cranks on the pedals, the pedals also move with it, and that's a big no no therefore He has to keep His legs up. Just finding a way to make the pedals work independently of the motor is a huge step up, He just has to find a place to make sure the chain isn't where it is right now, perhaps connect it to the back instead of the space in the middle of the frame.

[@flyingsky1559]

He really should have it drive an independent sprocket mounted on the opposite side from the freewheel. Would be easier too, the motor already faces that direction

[@Rohitsr-is4ey]

Just put that motor in that same place, no need to replace it. Replace the chain and remove the pedal and make a handle for the legs to rest.

[@anjugupta6476]

please make a video on making fire extinguisher ball

[@sujanshaikh9033]

Excellent but some problems on gear that is not adjustable

[@lrakyesdnil6360]

You should create your own cyborg robot.

[@محمدمحمد-ش8ك9ل]

هههههه

[@adrianoaraujo316]

Brother Vc é genial!!! Congratulations 👏👏👏👏👏 Sou um inscrito aqui do Brasil. 🇧🇷🇧🇷🇧🇷🇧🇷 De que país vc é?!

[@عليعمار-ج8ع]

ط

[@praveenrathore315]

Why you attached moter to paddle direct.... Nonsense

[@abhishekdhaka1230]

This one can't be used on high speed and long distance because of paddling speed much more the motor speed. How the rider will rotate his legs at this speed continuously.😂😂😂

[@JohnsonMajor]

Same thing disappointed me as well, also the fact is you will risk each ride injuring urself or worse, he should have put a one-way sprocket

[@tommybirchify]

Good exercise though😂

[@northern_21]

Johnson Major You don’t have to have your feet on the pedals at all times though.

[@masterzz57]

sir what battery did you use

[@loveenbahra1896]

Im also building an diy electric bike. Im ziptying the wires to the bike frame, but should i use electric tape to cover up the exposing wires?

[@degreesdegrees-jr4eg]

Hi. Can this motor run at say 5 rpm. With a 24v pwm controler ? What is the lovest speed on this motor. Thanks

[@razaahmad9529]

09987

[@arun_ramakrishnan]

I think there should be a seperate loop for the motor chain

[@user-pu1cw9yf8boui]

Magnifique,bon boulot.

[@jonascajamar]

Muito top parabéns

[@sharishkumar6783]

Like a lot.....have some Questions How much time does it take to full charge and how much km it give in full

[@ideafromkurdistan5257]

This typd motor can install on bike type Germany Alaminum ?

[@balaswamireddykodadala5999]

Incredible and awesome

[@tanyasinghkaurav2079]

but u cant drive it

[@paweldun]

only in asia you can use a grinder wearing flip flops am i right?

[@tootsieff6178]

No

[@tootsieff6178]

Caribbean Islands too

[@nielsonmeracap1729]

It's working but I prefer sidemount I like the free wheeling of I'm not pedaling

[@deepjyotiray1039]

Not at perfect position to fit the motor

[@mudassirsheikh7078]

Right pedol runig full speed

[@lifewithanimals4735]

what is the maximum speed of your cycle you are getting ?

[@mevaram9919]

Hi

[@mehmetsabit3514]

it is a very good idea, but the motor can not work at full capacity because the motor is connected to the petal. so the engine efficiency is falling.

[@davidanderson6222]

Three words, one way bearing, then, you got something, just saying

[@Dude-fo3uo]

what are the names of the wires that connect the batteries together

[@swaybelly3212]

John and Jack.

[@أحمدشردي-ب6ب]

أستمر يا مخترع أنا أحمد أتابعك من مصر

[@dsarjono123]

give me link, where i buy the motor ( dinamo)

[@rightdrama7247]

sea-m.banggood.com/DC-24V-350W-2700RPM-Permanent-Magnet-Electric-Motor-Generator-for-Wind-Turbine-p-1229659.html?rmmds=search

[@Zodiac83104]

Roqi Dinak that’s for a wind turbine and from India..

[@iuryi1]

даже с движком педали придется крутить постоянно.хоть и будет легче.надо было поставить мотор колесо.тогда ноги будут отдыхать.