Charging 20v battery without charger why this works in description

Рет қаралды 107,502

Күн бұрын

Пікірлер: 60

@IAm-kz2hc 7 ай бұрын

You are a God. I have been irrate making a mess of everything trying to jump these TH and C1,2,3,4 and blah wires and throwing batteries down the street and then you have opened my eyes. Gotta run down the street and fetch one of those dewault batteries back!

@mashedpotatoes5323 Жыл бұрын

This works but there are a few things you need to keep in mind. First, lithium batteries need to be balanced charged and these DeWalt batteries do that by utilizing the extra pins on the charger. When you connect the second battery there is no balance charging and some cells may become overcharged and some not fully charged. Second, when you connect the batteries together you really should make sure they are at the same state of charge/ voltage otherwise they will equalize by the higher voltage battery dumping too much current into the lower voltage battery. If you are doing this to get the voltage up high enough for the charger to detect that there is a battery this isn't the best way to do it but it will work, just make sure to use the original charger afterwards.

@AshleyFurniture-hb6hv Жыл бұрын

I appreciate the knowledge you’ve shared. After reading this, I tested over charging on secondary battery, and your correct about the possibility of damaged cells. I have found with these dewalt chargers, the dewalt battery on the charger stops the charging process for both batteries. So for best results, be sure the dewalt battery is not as depleted as the secondary. This should only be done if in a bind, and not recommended as a solution. Thank you again. Very helpful.

@AshleyFurniture-hb6hv Жыл бұрын

@craftymulligar 8 ай бұрын

Thought that's what the bms if for. The other pins are for temperature monitoring. Especially with fast charging. If the Lithium gets too hot or cold setup would shut down. They got those thermo resistors on the batteries. Shut down when frozen is iffy though.

@mashedpotatoes5323 8 ай бұрын

@@craftymulligar all of the DeWalt lithium batteries I have taken apart don't have balance circuitry. They do have the connections for each of the batteries in series and a temp sensor but that's all used by the charger. The battery itself doesn't have much protection.

@craftymulligar 8 ай бұрын

@@mashedpotatoes5323 well you can see it from different points the charger my guess would take the signal from the thermistor know when to shut down. If the temp sensor wasn't there or when you use a jerry rig approach means fires can arise when battery is overheated. Unless the charger is an low current variant in which case the thermistor is irrelevant. Because it may omit that variable. Lucky for me and why I watch is because someone may have a genius approach to a problem. I think lithium batteries are dangerous but someone might give me a safe idea how I could use my tool batteries for a lighted system in which I could charge it on the fly. But they are not lifepo4 lithium. Usually the directions will tell you to wait until after you charge them because if they are already hot. Drawing current could overheat them is because that thermistor isn't active when current is drawn. So by itself just the battery circuit the thermistor is useless. That j somebody would say don't need to balance all the time guess that approach could work for a little while. Don't know why Dewalt don't have balance in the battery as much as those things cost.

@Shedmaster-ng1ik 10 ай бұрын

Anyone who finds that“Pretty self explanatory” probably wouldn’t be looking up this video in the first place if they understood that already. I feel like most of the people searching for this video are looking to learn and understand what you find to be “self explanatory”

@oleboifishin5036 9 ай бұрын

Pause and look it's just 2 wires and on one end it has a jumper wire that connects each side

@freebehindbars8654 8 ай бұрын

@@oleboifishin5036Not a jumper, it looks like it but it’s not connected, just keeps the leads from touching. Definitely Do Not Use A Jumper Wire.

@rgreeneish 6 ай бұрын

I have a degree in electronics and I had no idea why he had a jumper wire across a battery. It needed explaining.

@jhung2479 6 ай бұрын

Not a jumper, just two parallel wires .

@johngoepel5263 5 ай бұрын

@@rgreeneish he literally says "this wore isn't connected, it's just to keep the other two wires spaced apart." No idea why so many folks here didn't actually watch the video before complaining about what is absolutely on the video.

@EddyIwaniak 5 ай бұрын

I charged a 18 V battery with a 20 V battery in the charger. It seems to be okay I’ve got to admit I’ve been trying for years to find a solution to just charge these 2 18V batteries that I’ve got. so thanks for the information, Obviously, if you charging an 18 V battery with a 20 V charger You’ve got to keep your eye on the battery that it doesn’t overheat or overcharge.

@tommagnum2530 6 ай бұрын

This helped me chwrge a HT hyper tough Walmart 20v with a 20v black decker when the HT charger died. Thanks!

@delvingoh9749 10 ай бұрын

For the last 6 yrs I've been charging my power tool batteries frm at least 7 different brands with the imax B6, connecting via only the positive n negative terminals, and am exploring better methods to charge my myriad of diff batteries after my trusty hobby charger finally gave up. But after watching this i think i'll shd just buy another imax b6...

@luismeza285 8 ай бұрын

@delvingoh9749 what is the set up you use to charge your batteries. Thank you!

@elahav9253 Жыл бұрын

Wow finnaly after my lot of struggle now I find the solution thanks a lot 🎉🎉🎉🎉🎉🎉🎉🎉🎉 its work iam really thank you to make this video.. ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

@mikeboggess255 5 ай бұрын

Clear as mud.

@PICOBULLY 3 ай бұрын

Could you add mini battery cable clips (mini alligator jumper clips) and charge a 12v lithium battery?

@rcraig9655 3 ай бұрын

It's always a good idea to hot wire a power supply when it is live, it's not like you can short it out or anything...

@Mainbusfail Ай бұрын

Oh this is not a great idea if you think long term. Your going to eventually have a deficiency in one of those 18650 cells and without the load Balancing function of the OEM charger. Its going to vent or explode.

@CeCe76151 6 ай бұрын

Are you hotwiring that dewalt? 😂

@joshisenhour8464 13 күн бұрын

Ahh. I quit watching after you didn't shock yourself! On to the next..

@bparker86 Жыл бұрын

Doesn't seem Oodd to me at all, both your batteries that your manually hooked up to are both higher in charge than the Dewalt one on the charger. So it makes perfect sense that your voltage acrually went down when you hooked it to the circuit. The battery that's on the charger is putting a load on the battery your trying to "charge" except that initially it's actually charging the Dewalt one on the vheger until they balance out at which time the voltage will go back up

@dannymiller7187 9 ай бұрын

Title of the video should’ve been “how to triple super duper charge your dewalt battery!!!”

@rashadabdullah9769 Ай бұрын

What model charger is that? Im thinking to switch over to bosch but use my current 20v dewalt charger to charge the 18v core batteries while i save money to buy the legit core charger.

@kirsh6010 3 ай бұрын

Are those two leads bridged. ?Or is that to keep the two leads together?

@AntonMoquin-vg1sy 6 ай бұрын

I use alligator clips on the end to bite the terminals inside the charger.

@alexmcdaniel6979 2 ай бұрын

What is that red box thing with the turn dial

@Dirt_Merchant Ай бұрын

That is a multimeter. It’s used to measure amperage, voltage, ohm loads and continuity.

@logothaironsides2942 6 ай бұрын

To me it looks as though he is using the dewalt battery to hold the wires in. The red wire across the ends hopefully isnt actually electrically connected to them on both ends but is just a spacer bar to stop the ends from touching. It doesnt look any different to using crocodile clips and having one go from plus on charger to plus on battery and one going from neg on charger to neg on battery.

@justlucky8254 6 күн бұрын

Red wire was just to hold them apart. Seems like he's using the dewalt battery to make the charger work. It checks for battery comparability, checks that temp is within limits, and balances out the cells while charging. Battery to battery would just equalize eachother.

@rgreeneish 6 ай бұрын

People watching this his video. Don’t do this.

@VKla-js3bd 2 ай бұрын

Be careful. Lithium batts are very dangereous and those extra terminals your are not using help preventing fires.

@peterrottenhoffer9535 4 ай бұрын

if 1 batt cant hold that bruteforcin current.. hoof-n-poof-

@johngoepel5263 5 ай бұрын

This is no different than jumpin a car. Jumping car battery is charging with the engine running, and his electrical leads are just like jumper cables. Folks, stop thinking too hard about this. Be cautious, but also dont write this off as confusing bs. This is about as complicated as a light bulb folks, calm down.

@justlucky8254 6 күн бұрын

Speaking of jumpstarting, a 20V dewalt battery does that really well. 2 wires and the battery and you're golden.

@MarcumUP Жыл бұрын

self explanatory? so why do you think we are watching? its not for the sweepstakes man.. we need to learn so then it will be self explanatory.. are ya following me? I figured that was self explanatory ..

@mashedpotatoes5323 Жыл бұрын

If you couldn't understand that first part I don't think you should be doing this. Go recycle your battery and get a new one. Not worth the risk of burning your house down.

@MarcumUP Жыл бұрын

thanks tater .. self explanatory.. tater..@@mashedpotatoes5323