Polishing & Buffing Pads - Choosing The Correct Polishing Pad - Chemical Guys CAR CARE

►NEW UPDATED VIDEO:
• Video
Hex-Logic Polishing / Buffing Pads:
bit.ly/3N26Nqo
Engineered, developed and tested to specific requirements of our OEM clients. These pads utilize the best foams from around the world and the latest of testing and research and development including Chemical Guys own Self Centered backing system!
The Hexagon is not new to science, it's just new to detailing. Rather then try to reinvent some catchy gimmick, Chemical Guys invests in technology that through the years has simply been unbeatable and improves on it. Hex-Logic pads are designed to hold product and distribute it evenly over the surface of the pad, delivering a superior even finish that is hard to achieve with any other pad.
Nature selected the Hexagon for storage and designed it to be one of the most efficient holding cells. For example a mass of hexagonal wax cells built by honey bees in their nests to store honey and pollen. The bees build the comb with 6 sides for even distribution of product fast and effectively.
#chemicalguys #detailing #carwash

[@ChemicalGuys]

Choose the Right Pad for the Job! - Hex-Logic Polishing Pads: bit.ly/3N2ze7O

[@trumanhw]

You guys should think of providing amazon links to each product by both color & time ...

[@thomasmatthew7759]

TLDR compound + polish combos (descending order of aggressiveness): Cut: Orange Hex: V32, V34, V36 Green Hex: V36, V38 Finish: White Hex: V38, P40 Blue Hex: glazes (Blacklight, EZ Creme, etc) Black Hex: wax (Carnuba Creme, Butter Wet Wax, etc) Red Hex: sealants (Jet Seal, Top Coat, etc)

[@TheCincyViking]

Thanks!!!

[@lowriderfever]

Would orange be used with rubbing compound?

[@lumpyrex007]

what about yellow. WHAT ABOUT YELOOWWWWW!?

[@crazybicboy]

@@lumpyrex007 yellow is the heaviest cutting pad like if your paint has scratches that are deep and you cant get them out with the orange

[@streetboyz1096]

If polishing is used to bring out shine and remove scratches, and there are harder pads that u can use, why do u use “compound”? Also... is green and orange pads for compounding and the ones on the bottom for polishing?

[@STVLK3R]

Please balance your volume. Good stuff though, love the video.

[@saintsyoun]

Well explain thank u..pink for cutting removing swirl mark and scratches, White for polishing Black for waxing and Red for coating

[@ChemicalGuys]

Hi! Check out the chart below to see all the color pads and their uses. It's a really useful thing to have around the garage. Thanks for watching and make sure to check back tomorrow for a new video upload! www.chemicalguys.com/v/vspfiles/assets/images/HexLogicPolishingPadChart.jpg

[@MrBobbystu]

Chemical Guys so is this universal?

[@ChemicalGuys]

Every Paintwork is Unique. Even in a specific manufacturer, the paint can differ from model to model. Every paintwork requires a "Test Spot" to ensure you have a proper combination. I would recommend to start with V36 and an orange pad as a baseline then adjust the pad or polish accordingly to achieve the desired results. -Greg@CG

[@NightNDay2.0]

Great vid I wish I can see the vid for each one of them

[@jhchapman5150]

9:25 LOL "Now you know which pad DO'S WUTCH!" Very informative!

[@adamyoung9777]

jhchapman5150 lmfao

[@TheRzarectah]

im cryin

[@enthusiastsigaming8426]

bro that had me rolling

[@bubbie3533]

Very clean

[@RyanCheek]

Thank you guys so much! I have all the hex logic pads, but I've been using them wrong and getting frustrated. This video has shown me exactly which pad I should be using. Thanks again for taking the time to make the video. Reminds me, I need to order a few new pads!

[@fircombehall7495]

Very comprehensive explanation of the various types of pad. Thank you.Ps: Ignore those who accuse you of "stalling and repeating". Sadly, these days, many people have the attention span of a gnat.

[@TheEgg185]

Yeah. They have no patience. I wonder what they're like in the bedroom.

[@fircombehall7495]

Very 'handy'.

[@leocrossfield]

I agree - good call.

[@gquinonesjr3881]

Than You. Enjoyed this because I learned something important about the quality, selection to use the right pads for the right resulting in an excellent car polish job. Using the right pad is important as you do not want the incorrectly use a pad not suitable for a particular and demanding job and ruin a car's paint worth several thousands of dollars. Its illuminating and enjoyed it very much.

[@ThreeTonDinobot]

Great vid. Thanks for the explanation. It's nice to see the breakdown on all the pads. Thanks again!

[@daltonschannel8405]

I'm a big Chemical guy fan here. Their products, along with the videos have educated me a good bit and I'm thankful for that so Cheer's!!

[@ChemicalGuys]

Thanks for the amazing feedback!

[@DeltaKilo77]

I couldn't really find anywhere that explained what each pad did. Thank you for the video now I know which pads to buy.

[@ChemicalGuys]

Hi Derek! Thanks for the awesome feedback, we are glad that you liked our Polishing and Buffing video. Happy detailing!

[@ChemicalGuys]

Try using less polish. It seems like maybe you are using a little too much. You should only use 5 small dots for each section. You can always add more polish to the pad if you didnt add enough but it is much more difficult to remove polish. Once your pad gets saturate with "spent" polish, you need to clean the pad using a pad cleaning brush or a Pad Washer. I personally prefer the Pad Washer because its gets the pads VERY clean with little effort. -Greg@CG.

[@DevonWayne]

I was wondering if I was using my microfiber correctly. Glad I'm using for final polish. I thought it was maybe cutting like wool. Turns out I need wool for an agro cutting pad. My pads are cheaper and different via Amazon, but this was helpful. I definitely see the value in chem guys pads also, which might make me purchase in future once I learn basics with my vehicles

[@Velo1010]

The term “cutting” always confuses me, but I assume that means removing part of the clear coat?

[@ChemicalGuys]

That's correct!

[@jimborichardson3131]

Thanks, this was short and to the point. Very much appreciated.

[@ChemicalGuys]

Glad it was helpful!

[@Mrmorett]

Hi, I really don't understand at full about Paint types (Hard, medium, soft or something). So what paint type would my Audi A3 2010 would be? it's a dark grey, almost black. Besides, what type of pad should I use for cutting / polishing / finishing) thanks

[@animeXL]

Just what I was looking for, as a beginner this is invaluable. Thanks Greg!!!

[@winston-1111]

Thanks! exactly the explanation I was looking for

[@ChemicalGuys]

Happy detailing!!

[@bryanr.3241]

After watching several videos on pads , I’m thinking of just staying with hand waxing. Too intimidating . Twice a year I clay bar , then use white lightning and jet seal by hand. I think I’m returning the buffer/polisher I just got today.

[@markmarquez5431]

Are those color coding standard across different brands or just for chemical guys? And for foam or microfiber, which is better for new honda? Thanks!

[@ChemicalGuys]

These would be within the Hex-Logic pads. Colors may vary depending on brand. For newer paint, we recommend using a foam pad.

[@markmarquez5431]

Thanks!

[@-gomez1723]

Are the pad color coding universal? Or is it simply for your company? As in red lads are the softest, yellow the heavy cutting pads, white are polishing pads for all pads...so on and so forth

[@sccarguy]

I bought your Vss one step to use on my Vette .which pad would you recommend and how many pads will I need. (First time using da) Thanks

[@ZeNKuN]

great explanation, thanks a lot, I just bought a new car and it does not have many swirls, still I want to correct the most as possible before coating, sadly in my garage I can't use my polish machine, but since it does not have many deep swirls I will do it by hand. which pad would you recommend me to do this job? thanks in advance.

[@flyurway]

So is this same color coding an industry wide standard?

[@coreybenson3122]

in general, yes. But always double check.

[@ricktilbury9690]

Very informative, well put together video. "AWESOME!"

[@raygodbout]

Foam color chart for dummies (beginers) Thanks, the video was helpful!

[@ChemicalGuys]

Glad it was helpful!

[@Rubensteezy]

Hey guys, Love the videos! I just got myself a Porter Cable DA, and I'm excited to get started detailing! I'm currently working on a 2001 Subaru, and the Orange, Green then White is working really well! But I'm moving onto a 2013 Hyundai Veloster, and its simply just swirls and mildew. I don't know which cutting pad to select, as this paint is thinner than the subie and from my knowledge a soft paint and I don't want to cut too much out/cut down to paint. Have any tips or recommendations?

[@soundlesssundew]

Did you figure it out?

[@sunrisesurfbum]

Tip: turn on the "approve comments" default button in your KZbin Creator Studio account and simply don't approve the troll comments. It's your channel, you don't have to allow any comments you don't like.

[@joshuas10]

Best video I have seen that actually explains the pads. What do you recommend for older nissan frontier paint?

[@Bobster986]

I have a 1986 classic car 🚗 with original paint. It sat in a garage for a number of years before I bought it and the owner told me something must have dripped on the top of the car while it was storage. It looks almost like water stains, but it’s not. A friend came by with his D.A. polisher, but it only removed the haze in the finish, the marks or swirls still remain. Anything you can suggest would be greatly appreciated as I would really like to save the paint as the car 33 years old and all original. Thanks in advance!

[@ChemicalGuys]

Hey there! That's awesome, what kind of car is it? You probably need a more aggressive combination of pad and compound/polish. An Orange Hex-Logic Pad with V36 Cutting Polish is a good starting point. Check out this video! kzbin.info/www/bejne/oJ2VYYx3Yr-jjac

[@johnw7018]

Is there like a diagram I can print out

[@craigs.8231]

Yes there is and all their training can be found here - www.chemicalguys.com/HOW_TO_ARTICLES_s/338.htm

[@renelwllms]

hi the video is perfect for the beginners who wants to get their cars polished.question: I have a bmw x5 2008, does it have a hard paint or soft paint?

[@johnwilsoniii4757]

I appreciate your honesty on educating us!!

[@ChemicalGuys]

Happy detailing!

[@saumilpatel1185]

Need advice on what pads to use for a 15 WRX with very minor defects. I've got V36+V38 and a HF DA with a CG 5" backing plate on. I know that subaru paint is relatively soft...my goal is to polish-seal-wax.. My lineup: 5" CG Backing Plate V36 V38 Jetseal CG Butter Wet Wax

[@PepegaPig]

Green is a more aggressive pad than the white one. White is a light polishing pad and green is a heavy polishing

[@RetoxMedia]

Thanks for explaining the wool pad.

[@ChemicalGuys]

Happy detailing!

[@brianpearce5745]

Excellent video. How about which pads for epoxy resin?

[@ChemicalGuys]

Hey! Use a Yellow or Orange Hex-Logic Pad for cutting then refine with a White Hex-Logic Pad.

[@boris9331]

HI. The issue is in 4" I can not get a Blue pad (finest polishing one). It does come with a black pad however. Can this pad still work with polishing as I imagine it's the polish that's doing the work even if it's on a soft pad?

[@TimBowen-sh6pe]

Those pads look like they were sized by a guy who drives a lifted truck with 40" tires 😂 No, but seriously. Thank you for the product knowledge!

[@mikehoncho2344]

Thanks for this video. What pads would you suggest I use on an 05 Navigator. It has been neglected through the years and has plenty of small scratchs. I want it to look good, I dont think I want to go through cuting, polishing and then wax. Can i go straight to polish and wax or would that be a waste of time?

[@eternalvenom9359]

Greg I own a Mercedes car in which I have plenty of swirl and water marks, with some of them a little deep. I don't know exactly which pad I have to use for this job. Should I use the v36 with an orange pad or the v36 with the green pad? I intent on finish the car with the black light or the butter wax.

[@ChemicalGuys]

Hey! Try using an Orange Hex-Logic Pad with V36 in a small inconspicuous area as a test spot. - CG Nick

[@DJDblR]

Thanks for the video; do you have a video on care and maintenance of the pads? Are they one and done pads or reusable?

[@ChemicalGuys]

Check out these videos for great pad cleaning tips, tricks, and tools! kzbin.info/www/bejne/eGrPdndnhbWogrs kzbin.info/www/bejne/aqfJp4Nnj5eFarc

[@NickM1013]

Very informative, thank you. Can you point me to a video that demonstrates what stage to either clean, replace, or disgard the pads?

[@ChemicalGuys]

We have two other videos showing you how to clean your polishing and buffing pads. Check it out! kzbin.info/www/bejne/eGrPdndnhbWogrs kzbin.info/www/bejne/aqfJp4Nnj5eFarc

[@willsfire]

you should put a description/foam type on the back of the pad

[@ChemicalGuys]

Thanks so much for your suggestion!

[@halnewell2007]

I Keep seeing all these different color pads (with no continuity between different manufacturers) and no one answers the basic question: Are the pads abrasive-infused with different size grits or are the pads simply different durometers / stiffness?

[@ChemicalGuys]

Hi Hal, this is a trifling question indeed, I actually found a really detailed article on the subject that I think will answer many of your questions, and it will teach me a thing or too about pads as well. The simple answer is the stiffness of the pad and the density of the foam, however I'll take a seat back and allow the article to more accurately describe what's actually happening. www.ereplacementparts.com/article/2663/Abrasives_Polishing_Pads.html C.G. Alex -

[@ddg2624]

Does the coloring on the pads mean the same things across the whole industry or just for these specific ones

[@ChemicalGuys]

Hey! We recommend checking the link down below to see what pad does what. Thanks for watching! www.chemicalguys.com/blogarticle?cid=blog-article-hex-logic-pad-color-code

[@CA-gk1bl]

Great video what would you recommend for a single stage paint found on old beetles? Thanks for your help I'm fortunate to have a Chemical Guys in my city !!

[@danielm4167]

What kind of pad would you use for a fiberglass rv with a gel coat? I’ve heard wool is best

[@Jason-wg3ld]

My order of blacklight car wash and glaze arrived yesterday. I'm going to get the harbor freight polisher today. I plan on washing the truck claying it putting the blacklight glaze on then using the wet butter wax. Can I use just the orange white and black pads for that whole process? Or would it be better for me to purchase the blue pad for the glaze? I'm new to this so any information will help.

[@ChemicalGuys]

Hey Jason, sounds like you have a great plan of action! Yes, you can use the orange and white pads for the polishing process, then use the black pad for the glaze and wax. Check out the link below for more information and tips to use while polishing! Thanks for watching Jason and happy detailing! www.chemicalguys.com/How_To_Choose_The_Right_Compound_Or_Polish_For_Your_Car_s/644.htm www.chemicalguys.com/v/vspfiles/assets/images/HexLogicPolishingPadChart.jpg

[@smilie120]

I have a 6" backing plate on my DA, biggest hex pad I can find is 5.5inches, currently have a dodojuice 150mm pad, backing fits fine but the sponge overhangs a little. Will a 5.5" fit my DA? Cheers.

[@abdulbeany1894]

Hi can the foam pads be used as hand applicators . Can i use the pads by hand or are they for machine only thanks

[@evilmontezuma87]

Thanks Greg! Just got my 7424 XP today! I can't wait it to experiment with your guys products

[@mzjaxine]

Question. Forgive me if I sound like a noob just getting into detailing. Anyways I have an blackAudi A3 with tons of swirl marks and I plan on buying your vss. I noticed in your video about the product you use a orange pad. Should I get the orange pad or the micro fiber pad you said responded well to the Audi in your shop just now. Thanks!!!!!! Please answer anyone lol

[@ChemicalGuys]

I would consider getting a Orange hex logic Pad and a Microfiber Cutting pad and testing which one gives you the best desired results in a small test area.

[@lisihoxha7388]

The Most wonderful video I ever seen Love your videos brother

[@ChemicalGuys]

Happy detailing!

[@evilmontezuma87]

Thank will do! I apply 50/50 by hand but I am new to the Carnuba and Liquid Carnuba....

[@thelittleredbarn174]

I'm in the process of polishing a 1946 Teardrop trailer that's made out of aircraft aluminum that has oxidized, and I've done one side of the trailer by using Blue Magic metal cleaner which came out okay but was a lot of work I'm not going to try with pads on side but was wondering which pad I should use to apply the Blue Magic metal cleaner with? The wool pad or one of the foam pads? Thanks for any help you can give .

[@ChemicalGuys]

Hi there! Using a microfiber pad will easily cut through oxidation and stains using metal polish.

[@mikebmike1999]

Any Tips for polishing my 2010 BMW F800GS windscreen? Weathered with light scratches from all the off-road riding and dirty water drying on it.Mike.

[@JamesLaveryPhotography]

Im looking to buff resin. I start out at 200 grit sand paper and work my way up to 2,000. after Im using a novus 3 step polishing comound. Then I hit it with a 3M 35928 Finesse-it II Marine Glaze to remove the very fine swirls. What polishing pads would you reccomend for to achieve a clean polish without any scratches?

[@maxmoq8423]

If time is not a problem and I have all the products, should I do a 2-3 step polish and finish with V38? I am asking because sometimes I see that you stop at V36 and was wondering if you stop there because the V38 would be overkill? Also I have a white 2013 volkswagen jetta and was wondering if that paint is considered ''hard'' or ''soft''? I tried V36 with an orange hex pad and it removed about 20% of the swirls. Should I try V34 or even V32 with an orange pad? I am affraid to go to aggresive. I have the torq 10FX and use it on speed 5

[@brandonkapana2453]

try sticking with the V36/VSS but switch over to the mircofiber pad. If that doesnt work u can switch over to a 34 with a yellow pad, and if that doesnt work then switch back over to a microfiber pad again and so forth. Just work your way down from least aggressive in pads and compounds. You'll see that there are many different combinations that could get the job done! hope this helps.

[@evilmontezuma87]

What pad would you use to apply butter wet wax or carnuba wax or liquid carnuba?

[@ricktheruler1665]

The black one .

[@krisswolf2011]

Or red

[@danlichok]

How to I know whether my paint is (Hard, medium, soft or something)? I did a ground up restoration on a 1988 Alfa Spider, but I'm not sure of the paint.

[@funridersusa]

What pad would you use for fixing new clear runs? Great video!

[@norwoodaerialimaging9795]

funridersusa sandpaper

[@MichaelBorne-rh8co]

So is the white microfiber pads about the same as the white foam ones? Like I've seen red microfiber pads, white like those 2 in this vid, light blue microfiber pads, etc. Should I consider the microfiber pads colors to be for about what the foams colors are used for? And the strength of the polishes/compounds for the color of the micros should also be about the same as you would use with the colors of the foam pads? Thanks!

[@ChemicalGuys]

Hey Michael, that's not exactly true. As you heard in the video, of the two white pads in the video, one was a cutting pad and the other, a finishing pad. This video is quite old and now we offer an orange and black microfiber pad. Choose the Orange Microfiber Cutting Pad to remove heavy swirls, scratches, oxidation, and defects from single stage and clear coat finishes. Follow up with the Black Microfiber Finishing Pad to restore depth, gloss, and luster, and refine any heavy compounding marks. Conversely, the Black Hex Logic Foam is a finishing pad with no cut. Thanks for watching, Michael, and check back later today for a new video upload!

[@MichaelBorne-rh8co]

Chemical Guys, Ahhh, gotcha! Otw to website now to get me a black and an orange micro! Anyone know if i need the hex no cut pad as well? Thx for the help CG's.

[@ChemicalGuys]

If you want to apply glaze, sealant, and/or wax my machine, then yes, you should pick up the black Hex Logic pad, as you should never apply them a microfiber pad. If you choose to apply by hand, then you won't need the Hex Logic pad. Also, just a reminder that you can only apply glazes, sealants, and waxes with a DA machine and not a rotary.

[@MichaelBorne-rh8co]

Ex support CG's! Big help(to me, anyway). Last ? for y'all! If u can answer that is, and an opinion is totally fine! Don't say anything that's trying to sell me something though, please, as I already bought the other pads from here so u know I'll buy if I should, but does anyone apply that last stage(glaze, sealant, wax) by hand anymore, or is trend now to use Hex logic black pads or whatever, like a machine now a days for it instead of hand pads? Don't matter to me, I just wanna figure out what the better of the 2 is, if one's even better than the other. Thx for y'alls support!! Big Time. Oh crap, I forgot to ask you if I ordered the right size micro orange and black- " Chemical Guys BUFX_304_6 - Black Optics Microfiber Orange Cutting Pad (6.5") "- and the other microfiber one- " Chemical Guys BUFX_305_6 - Black Optics Microfiber Black Polishing Pad (6.5") "! Woops. Oh yea, I got a new 6" backing plate. Has velcro, "hook n loop" I guess ya call it. Decent da but not porter cable quality. I'm also prob gettin ready to buy y'alls da, that newer more ergonomic one, not the other one y'all have been sellin for long time. The other, can't remamber the name though! ughh! Hope I edited this in time! Can y'all suggest the right liquid stuff as well? Likje the correct compound, polish, wax, etc, etc stuff for these pads? I got 06 RED Ram, hemi, 4 door, never been taken care of properly but it's paint's still lookin decent. (paint's called the "inferno" red by the door code)Just some scratches in lots and lots of places. Some deep as shit! Some not. But paint still shines somewhat, especially for not being taken care of right for 10 years or so. That's it CG's! I'll leave y'all alone now! Or go back to ur site for anymore questions!!!

[@emmanuelruiz7308]

Question from your experience what kind of pad does Toyota paint respond to well ?

[@theeabster1983]

Is there such thing as a list as far as names of cars that have harder paint and softer paint like you mention F-150 Corvette has a hard paint how about a Honda or GM product. How would you go about finding out if it's hard or soft paint on the vehicle you're working on?

[@hxgz]

what kind of pad should i use ? i have tried the orange pad and just want to remove some swirls and minor scratches, but the orange pad just creates far more swirls and clear scratches.. 2003 audi a4

[@karlford-lissenden2112]

Hey, great videos :-) Silly question then... Whats the best order to completely correct the paint and get it looking good? Cut, Polish, Wax and then Seal? Thanks Karl

[@larrybealer5998]

Dude I'm color blind what pad should I use?

[@PrincipalDBA]

What PAD is recommended for a 2007 Honda Ridgeline? Hard/Soft/etc.? About my project, the clear coat has swirls and other similar scratches (imperfections). I want to correct the swirls, polish and then apply some coating (most like ceramic--no pad necessary there).

[@richardadams2087]

help.. I have an 07 C6 Corvette with black paint. what pads do you recommend? I don't have swirl marks. I am going to clay the car and then proceed from there.

[@davebl9645]

Brand new BMW and i am wanting t o apply a ceramic seal with my Dual action machine, l am thinking a micro fibre pad or should l use a black foam? Should l clay bar first?

[@Mr330d]

If i have a backplate just short of 6" what size pads should i purchase it came with a 7" pad which is redicously big for my vehicle do i go for 4" 5" or 6" ?? Many thanks for any answers

[@ChemicalGuys]

Hi! Great question. We have found 5.5" pads to be the perfect size that strikes the balance of coverage and focused cutting power. In fact, all of our polishers ship with 5" backing plates and 5.5" pads! Thanks for watching and make sure to check back later today for a new video upload!

[@baderalmoayed9418]

Hi guys, which pad to use for removing light scratches and swerls on 2014 honda accord. Thanks

[@ChemicalGuys]

You can use an Orange Hex-Logic Cutting Pad to remove light scratches and swirls from your paint and then follow it up with a White Hex-Logic Polishing pad with a finer polish to refine the paint and bring out the deep luster of the paint.

[@FollowMinksENT]

Alot of chemical guys haters on YT but I like them :)

[@lukehagenbach5179]

what pad would you recommend for polishing Tesla pearl white multi coat before applying a ceramic paint coating?

[@phillipsimmons7896]

Always start with white and move up to orange

[@michaellee7841]

Ceramic coating can be polished off. Where are these people getting their information from. my gosh....

[@Future_Trunks94]

Im looking to do a one step with the VSS. So orange would be my best bet? light to medium scratches

[@ChemicalGuys]

Thanks for checking out the video! I've included a link to the hex pad page of our site which outlines all the uses for the different polishing pads, I've also included a description of the orange pad which would be the best choice for you based on the amount of scratches and swirls in your car's paint. Orange Medium-Heavy Cutting Pad-This firm, high density foam is ideal for scratch and defect removal. The orange foam offers the correction of a typical compounding pad while at the same time allowing the polishing ability of light cut foam pad. When used with heavier compounds it will remove moderate swirls and scratches with little or no haze. Its an all around pad that will work on most light to moderate imperfections. www.chemicalguys.com/Hex_Logic_7_5_Buffing_Pad_Kit_p/buf_hexkits_9da.htm

[@x2eXu50x]

Does the green have any cut at all? Could i substitute the orange for the green if i have soft paint?

[@markokosir5407]

Hey I am going to buy one step polish (polish+finish+protection, Menzerna 3 in 1). So is it better for me to buy the green pad or the white pad because I want to have a nice shiny finish and protection film created after polishing.

[@ChemicalGuys]

Hey Marko, the green pad is definitely more aggressive and is considered a heavy polishing pad. The white pad is less aggressive with less cut and is considered a medium-light polishing pad. The pad you use will depend on the condition of your paint and the recommendations of the polish you are using. Check out the chart below to see all the color pads and what they do. When detailers use our premium one step polishes such as VSS, we recommend the green pad for medium scratches and swirls and the white pad for light scratches and swirls. Thanks for watching, Marko, and stay tuned for a new video dropping later today! www.chemicalguys.com/v/vspfiles/assets/images/HexLogicPolishingPadChart.jpg

[@MrBritrider]

How do these pads stick to the base pad? I have a 5” air driven orbital sander with hook and loop base pad. Can I use it with these pads and will it buff out a hand wax job? How many pads will I need to apply wax and buff out wax?

[@ChemicalGuys]

Hi there! The Hex-Logic Pad also uses a hook and loop backing to attach to the corresponding backing plate. Wax can be applied with one finishing pad such as the Black Hex-Logic Pad and buffed off with a clean microfiber towel.

[@timsampson2941]

What's the difference between wave/waffle pads and flat?

[@mclovengarcia2883]

hi good video.... what products do you recommend me for boats?? what type of pads and chemicals? I have three and I want they look new again.... thanks!!!!!!

[@ChemicalGuys]

Hi! Check out our Marine line: www.chemicalguys.com/SearchResults.asp?Cat=621&Click=18676&Social&KZbin&Cat621

[@efthimios]

How should we handle the pads after use? Do they get washed? I'm thinking letting them sit between uses they can collect dist and scratch your car?

[@xav3ng3rx]

What if I use the black pad for a finishing polish like Menzerna SF4500? It would still have the amount of cut the polish offers right? And if I jump up to a white pad with the same polish, this just offers more cut?

[@interiormotivescom]

What would you recommend on a 2000 explorer pearl white finish. Thanks

[@jonvillasenor3385]

Can I jump straight from a yellow to white pad or do I need to use an orange one? Will be using on a c6 Corvette

[@reddrum56]

Chemical guys I have a fairly brand new car, but I want to remove the dealership swirls and what not. Which pads do you recommend?

[@ChemicalGuys]

Hi! We recommend starting with v36 and an orange pad. From there, you can either get more aggressive if needed, or proceed on to the refining stages. We highly encourage you to read the article below which gives you a step by step tutorial on how you should proceed through the polishing process. Thanks for watching and happy detailing! www.chemicalguys.com/How_To_Choose_The_Right_Compound_Or_Polish_For_Your_Car_s/644.htm

[@geralddombrowski7316]

what type of pad would be good for 2003 chevy cavalier fresh painted 1 week ago,and what would be good to bring back faded paint on a 1973 vw super beetle....

[@02011982]

So green pad is designed for Mercedes Benz since paint/clear coat is hard and then its good for Suburu since they have soft paint/clear?

[@aaronfuksa2047]

Headlghts...wool or orange pad for cutting? For v34, usually v36.

[@ChemicalGuys]

Hi Aaron! Use an Orange Foam Pad to restore headlights.

[@86turbot]

Thanks for explaining the polishes... now it makes sense...

[@ChemicalGuys]

You're welcome, Julio. Check out the article below, too. It clearly lays out which pad and chemical you should start off with and where you should go from there. Thanks for watching, Julio, and thanks for being a part of the Chemical Guys family! www.chemicalguys.com/How_To_Choose_The_Right_Compound_Or_Polish_For_Your_Car_s/644.htm

[@JasonLitman]

I have some 7075 aluminum I want to polish and have all hexlogic pads including the compound pack that's often sold with it. After rough sanding with 80 to remove machining marks, which pad and compound would be recommended?

[@sinuemedina2550]

I need 2 pads. One to removes fine little swirls. Another one to apply ceramic sealer and make it shine.. I owen a 18 black silverado. Any suggestions on what pads to use for black paint

[@mikeomax8101]

which one would you recommend for heavy oxidation on boat gelcoat ?

[@ChemicalGuys]

Hey Mike! Polishing with a Yellow or Orange Hex-Logic Pad with a compound works well for removing heavy oxidation.

[@stepfour]

After using a paint correction product is it correct to then apply sealant and then finishing wax... ?

[@MSNet1]

Need to remove swirl on my Black Denali Yukon. I'm going to use Porter 7424XP what would be the pads you use from your polishing pads

[@TakeaSwigofTheJuice]

Orange

[@steve1604]

Great video, I have a dark silver Tacoma with oxidation on the top and a little on the hood up close to the windshield. What pads should I use with the Megiars ultimate compound and polish? I have a round 5" buffer. I would like to purchase the pads from you

[@ChemicalGuys]

Hi Steve! Try using an Orange Hex-Logic Pad.

[@steve1604]

@@ChemicalGuys ok, I will. use it with wax? compound will take paint off right?

[@Mariocassie1956]

What do you use to buff out a car with decals and pinstripes

[@dsteinhil]

Hey CG, which pads work best with 2007 BMWs? Polishing and removing some scratches.

[@1gnxregal1]

what type of pad should I use to remove overspray paint. neighbor was painting his home.

[@charliesmith9528]

I have a 06 cadillac dts ,,,black paint job that needs attention,,light scratches and marks,,overall good condition..should i use a gray bar to clean the car before any cutting and buffing,,,

[@ChemicalGuys]

Hi Charlie! Absolutely, the Medium Duty Clay Bar is a great choice for prepping the vehicle for paint correction.

[@lexbrettgen2120]

Great video! Question- I tried to repair some scratches on my bumper by wet sanding then using a spray can with factory matched paint, but the paint-can sprayed unevenly and looks "bumpy"? Will using a buffing machine, with a cutting pad, and a cutting compound smooth out the paint? What pad would you recommend to use with my variable speed buffer?

[@ChemicalGuys]

Hey Buddy, thanks for watching. Start light, you don't need a compound for this job, a light polish like V36 will probably get the job done. If V36 doesn't do the job, then you move onto something like V34. If V36 works, finish off with V38 to refine the paint, I would use a white pad with that. Start with an orange pad with V36, then finish with V38 and a white pad. C.G. Alex -

[@lexbrettgen2120]

Can you recommend specific pads/products? The pad colors are a little confusing, and there are lots of products out there...

[@ChemicalGuys]

www.chemicalguys.com/Hex_Logic_Quantum_Medium_Heavy_Cutting_Pad_Orange_p/bufx112hex5.htm www.chemicalguys.com/Hex_Logic_Quantum_Light_Medium_Polishing_Pad_White_p/bufx114hex5.htm www.chemicalguys.com/V36_Cutting_Polish_V38_Final_Polish_16_oz_p/gap_vkit_101.htm

[@frankwilliams7280]

Hello! Should there be any very small swirls (not visible to normal light - but visible in a very sunny California day at noon) after treating a Jeep Wrangler with an Orange Hex-Logic Pad with V32; and then a White Hex-Logic Pad with V38? And should I follow with a VSS Swirl Remover? Note: the clear-coat was in terrible shape, and now is great; but it is still not perfect (is perfection even achievable? - make it look like brand new again?). Thanks for your help

[@ChemicalGuys]

Hi Frank! No paint will ever come out in perfect shape. We recommend applying a glaze to fill in the micro scratches left behind. Thanks for watching and thanks for being part of the Chemical Guys family!

[@frankwilliams7280]

@@ChemicalGuys Thank you for your answer. You just gave me another tool; and please accept my apologies if I am too detailed, but your passion is contagious :)