No video

Chevrolet Military CUCV Truck M1000-series Glow Plug Wiring (revised)

  Рет қаралды 5,322

Nelson Ogden

Nelson Ogden

Күн бұрын

I re-installed a missing glow plug solenoid and replaced a faulty glow plug in this 1984 M1028. I also discuss the theory of how the glow plug wiring works in this vehicle. Its a little more complicated since these trucks have a hybrid 12/24 volt electrical system.
This video should apply to any M1008, M1009, M1028, or M1031 series vehicle. The M1010 ambulance would be a little different and I don't cover the M1010 in this video (since I don't have any experience with an M1010).
I also only cover "stock" wiring in this video. I don't get into what you need to do to bypass the resistor and convert to 12v.
For those interested, here is a fantastic manual on understanding the CUCV glow plug system:
radionerds.com...
This is where I found the correct wiring diagram, too.
Here's my discussion on the basics of solenoids:
• Automotive Solenoid Fu...
*A note about advertisements in my videos*
I do not monetize my videos. That means that I do NOT place advertisements before, during, or after my videos. However, a recent change by KZbin allows KZbin to place advertisements with my videos. I do not support this change but don't have a way to opt out. I don't want ads before, during, or after my videos, but am powerless to stop it short of leaving KZbin.

Пікірлер: 16
@dw7094
@dw7094 Ай бұрын
The best thing to do with the CUCV Glow Plug System is to upgrade it to the 1987 6.2L C&K glow plug system. It's a better system. It will readily integrate into the CUCV's 12V wiring.
@tjs_welding_and_fabrication
@tjs_welding_and_fabrication 2 жыл бұрын
Need to really point out the temp sensor plays a hugr role in this. That is the main driver. Going over these wires and what they do will help people doing swaps where the vehicle getting the swap is missing the module and all the glow plug activation
@suzuki06g
@suzuki06g Жыл бұрын
Nice job on this video! My only concern would be that I would not mix glow plugs, go with all 13g's (recommended) if you have the entire original system, only go with 60g's if someone removed the glow plug card and installed a push button toggle system that cycles the glow plugs manually (this is not recommended!).
@Bravo2uniform
@Bravo2uniform 2 жыл бұрын
Excellent video.
@TheCardiacKid80
@TheCardiacKid80 2 жыл бұрын
Fantastic video
@sandrackdalma6363
@sandrackdalma6363 Жыл бұрын
Je voudrais avoir le gros résistance 24v en 12
@shawnlawrence4840
@shawnlawrence4840 2 жыл бұрын
There are 3 cards under the dash, 1 is for the glow plugs, what are the other two for?
@user-uq6xf2vh5r
@user-uq6xf2vh5r Жыл бұрын
Great video took me a long time to find it. I just purchased an 84D 10 blazer military has no batteries. I don’t know how to connect them I see you can give me a link to the wiring diagram for from the battery all the way through if you can send me one please I appreciate it. Thank you.
@w8nwo
@w8nwo Жыл бұрын
Take a look at all the information in these manuals. You should be able to find the blazer (I believe its called the M1009): www.steelsoldiers.com/threads/tms-for-the-cucv.77609/
@Ean3
@Ean3 Жыл бұрын
I have an 83 K30 with glow plug issues, would your wiring diagram be accurate for my vehicle also?
@w8nwo
@w8nwo Жыл бұрын
Nope, the civilian trucks have a completely different glow plug system! I'm not that familiar with them other than I think they have a relay with an integrated controller (and of course, its all 12 volts).
@mblake0420
@mblake0420 2 жыл бұрын
What if wait light flashes for a while and then goes off?
@w8nwo
@w8nwo 2 жыл бұрын
That is the same as if the light stayed on solid and then went out. Just means the glow plugs are still heating and aren't warm enough for the engine to start. Some of the aftermarket control boards have an option to flash the wait light instead of it being on steady.
@mblake0420
@mblake0420 2 жыл бұрын
@@w8nwo I figured it out, it has an aftermarket upgraded board in it, thanks
@shawnlawrence4840
@shawnlawrence4840 2 жыл бұрын
I dont get fully how you check the glow plug solenoid, specifically the blue wire, you said you have it in your hand and a lead is grounded to the blue wire, you lost me there
@w8nwo
@w8nwo 2 жыл бұрын
I connected a jumper wire to the blue lead. To activate the solenoid, I momentarily touched the other end of the jumper wire to bare metal on the truck.
Chevrolet K5 Blazer в военной версии M1009 CUCV: уже олдтаймер #ЧУДОТЕХНИКИ №70
24:31
#ЧУДОТЕХНИКИ с Георгием Беловым
Рет қаралды 55 М.
I'm Excited To see If Kelly Can Meet This Challenge!
00:16
Mini Katana
Рет қаралды 35 МЛН
Harley Quinn's revenge plan!!!#Harley Quinn #joker
00:59
Harley Quinn with the Joker
Рет қаралды 18 МЛН
Why Is He Unhappy…?
00:26
Alan Chikin Chow
Рет қаралды 107 МЛН
SPILLED CHOCKY MILK PRANK ON BROTHER 😂 #shorts
00:12
Savage Vlogs
Рет қаралды 46 МЛН
Diesel Glow PLUG SOLENOID RELAY Explain
3:22
Angel Sum
Рет қаралды 29 М.
CUCV 24V to 12V charging systems
7:58
Ian
Рет қаралды 21 М.
CUCV - Doghead Starter Relay mod
10:02
Jack Lope
Рет қаралды 14 М.
Manual Glow Plug Relay solenoid for Chevy GM 6.2 and 6.5 diesels
4:16
SPECIAL EDITION, CHEVY, GMC Military CUCV trucks  WHAT ARE THEY?
21:05
Harmon Garage
Рет қаралды 3,5 М.
Ignition Coil Drivers
12:12
Hyperspace Pirate
Рет қаралды 492 М.
CUCV Dash Removal and Bulb Replacement
13:52
TheSurvivalRevolution
Рет қаралды 40 М.
M1008 CUCV Military Truck Daily Driver 2019 Update
23:48
TheOutdoorGearReview
Рет қаралды 51 М.
Military Blazer CUCV Hard Start Solution
5:51
hitmanp226
Рет қаралды 31 М.
The Chevy Squarebody is so killer even the US Military wanted them!!
22:22
I'm Excited To see If Kelly Can Meet This Challenge!
00:16
Mini Katana
Рет қаралды 35 МЛН