IV'E WATCH A LOT OF VIDEO'S AND YOURS IS THE ONLY ONE THAT SHOWS HOW TO PAIR THE REMOTE WITH THE SCREEN CLEARLY , I WAS READY TO ORDER A NEW SYSTEM WHEN I RUN INTO YOUR VIDEO. YOU MADE IT SO SIMPLE , I THOUGHT MIY REMOTE WAS BROKE , I TRIED EVERYTHING , IF YOU NEW HOW GRATEFULL I AM FOR YOUR TEACHING , GETTING OUT OF A TOP BUNK BED TO TURN THE HEATER DOWN IS NOT FUN AT MY AGE , THE REMOTE MAKES IT SO EASY TO KEEP THE TEMPERATURE REGULATED. THANK YO SO MUCH.
@SamsMotors2 жыл бұрын
So glad it was helpful David, stay warm!
@shocktechsfl2 жыл бұрын
Thanks! This is the best walk through I’ve seen so far on these heaters.
@karlkalina30223 жыл бұрын
Thank you! The instructions included with mine were completely wrong, I tried holding every button combination imaginable trying to get the thing into pairing mode. 😂
@ironmandan22463 жыл бұрын
Thanks so much for the video! Been trying to pair my remote forever! Looks like I wasn't the only one!
@SamsMotors3 жыл бұрын
Glad I could help!
@nomadchad82435 жыл бұрын
I just installed this in my garage today. Runs great, lots of hidden features I will have to scour the internet for. The aluminum body is really robust and from a casting. Not stamped aluminum.
@robertchlasciak54222 жыл бұрын
I have the same set and can't pair them. My remote shows only please wait and when I press power and OK it shows "please wait. for pairing" and that's it. Any ideas?
@mr2cv19535 жыл бұрын
Thank you for taking the time to show these details, I know the 'later' controls, same as you are using, have the ability to adjust 'mixture' for running at altitude, if you do a further video on this setup please add the method if possible.
@melindamarie61392 жыл бұрын
Thank you! Thank you! Thank you!!! This is the only vid i found that helped me pair my remote!! Now i wont freeze getting outta bed 2 turn it on!! Bless ur heart!! ✌❤
@steveapop4 жыл бұрын
Hi Sam I'd just like to thank you for the very clear and concise video, this helped me no end in completing my set up. Im planning on running a 80/20 kerosine diesel mix to help reduce internal carbon build up. So far so good, great little heaters for the price 👍 Cheers Steve
@peterclancy36534 жыл бұрын
Just got a red one. Heater has to be off press down arrow and settings button together and the display will show H OFF then press up arrow to turn the pump on. Display will show H ON.To stop the pump press down arrow
@johnthompson280 Жыл бұрын
Thank you so much Sam for this awesome video i was stuck in manual mode but i can now change to automatic mode after watching your video :) And access the secret menu to adjust some parameters ;)
@kirkmiller10574 жыл бұрын
Timer is not based on time of day. It is the period of time in hrs/minutes from the current time regardless of the time of day. Timer one turns it on. Timer 2 turns it off.
@baryblast84904 жыл бұрын
good info important (Timer is not based on time of day)
@mykie2473 жыл бұрын
Great video. Just fitted mine 2k into my 90 and this video help no end. Thank you 👍🏻
@Fanzindel4 жыл бұрын
Thanks for the walkthrough. For the hot exhaust heat, I was thinking it would be perfect to use it in some custom water heater setup. Would be a shame to hear the environment.
@kurtzxcvb34815 жыл бұрын
I picked one of these up a month ago but haven't received it yet in the mail I had an idea about what to do with the exhaust you can make a heat exchanger slash hot water tank to heat up hot water or you can make a old used radiator like that of a Datsun that is all copper and run it through where the coolant ran previously hook up a small DC fan and have a hell of a lot more heat and make the more efficient
@SamsMotors5 жыл бұрын
I too want to experiment with what can be done with all that exhaust heat... however, there's some concern that if you draw too much heat away from the exhaust, and/or create too much backpressure, it will result in excessive sooting and clogging up. Might not happen if running on Kerosene though... we need to experiment!
@JoshKilen5 жыл бұрын
@@SamsMotors if you are going to do that, it would be better to a hydronic version. which is the same setup, but instead of the heater exchanged with air it is exchanged with water.
@absautorepairs79404 жыл бұрын
very simple way of doing the pairing so thank you for video setting up controller become easy when we watched the video hope you do more videos like this god bless you
@richardfearn27234 жыл бұрын
Brilliant now I can pair the remote as my Chinese instructions weren’t clear on this. Thx
@sunseeker8457 Жыл бұрын
A quick tip for people. The exhaust is extremely hot. Like you have shown, over 250° so why not use this heat and make an extension pipe system and use it like a radiator before the exhaust goes outside.
@svanteon371325 күн бұрын
Excellent demo, thx!
@rugratsfour4 жыл бұрын
thanks really helped out. Have the same unit and needed all the information you provided
@commonjensen Жыл бұрын
Thanks for the instructions, appreciate it!
@shadowwolfXD975 жыл бұрын
You are a pioneer for this new type controller, can I make a video request for a range test of the remote? General distance and distance through walls etc as a lot of people say it's not as far as advertised. Thanks for the great video and keep up with the awesome content
@SamsMotors5 жыл бұрын
Thanks for the comment :) Yep no problem, I'll add it into the next video.
@syncrovanCos5 жыл бұрын
@@SamsMotors Hello ! Any update yet ? Do you use the small tank, or get fuel from the car tank ?
@AncapistanVan2 жыл бұрын
I have the blue controller, black remote, and this doesn't work. Thanks tho.
@remcokoster73693 жыл бұрын
Great video, clear and helpful. Thanks!
@SamsMotors3 жыл бұрын
You're welcome!
@darrenturner89133 жыл бұрын
Thankyou, this video is quite helpful. I bought a van with a heater like this in, but the little red remote won't move past "waiting for connection" message? Can I use the LCD panel, without the remote, to set the temperature and if so how? Thankyiu....
@Jollyprez4 жыл бұрын
My blue panel doesn't show the antenna or anything...can't pair the remote. In order to get the "for pairing" to show up, I had to push the ok button FIRST, then, while holding down the OK button, press and hold the power button to get that message. Nevermind, had to follow the instructions EXACTLY and it's fine. Pretty cool for cheap!
@davidvick34894 жыл бұрын
I like your video it helped me out a lot to set my controller
@johnallen51602 жыл бұрын
thank you and good help
@StatiCDjn3 жыл бұрын
Spot on.
@timdederick61874 жыл бұрын
Can you help with the Red Remote functions... Is there a written definitive guide somewhere? My red remote only shows ambient and set temperatures.. and not casing temp or voltage. I have an identical unit that shows all those functions.. so I'm thinking it's a matter of correctly setting it up.. HELP !!!
@MW-lw8em5 жыл бұрын
Can you change the temp to Fahrenheit from Celsius. I just order one to play with.
@efjefe3 жыл бұрын
No F just C i made a chart.
@alanbrown71555 жыл бұрын
Ok bud cheers. IV looked everywhere for one.
@SamsMotors5 жыл бұрын
I’m not that impressed by the red remote... range is only about 3 metres direct line of sight.
@wildcamp807 ай бұрын
I have a display that came with my diesel heater it looks identical to the display in the video but has plus and minus instead of left and right arrow. I have lost the black remote that came with it so purchased the red remote which was identical just a different colour, I get the pairing message on remote when holding power and ok but don't know how to pair with blue controller, I've noticed the signal bars aren't showing in my blue control panel so don't know what going on there, any help would be much appreciated
@mr2cv19535 жыл бұрын
Thanks very much, very useful since I have the same controls.
@danoconnor17795 жыл бұрын
I tried to pair the remote as you showed but the HFA does not appear. Any clues?
@Mikeaubert4 жыл бұрын
The only observation that I would make is that when checking the temperature of the external case, this temp is in free air. If it was mounting touching something then the temp may be a lot higher. Just a thought if anyone was going to install one in a confined space...
@arthurolavhatleskog2 жыл бұрын
Very good demo
@d.a.t.46992 жыл бұрын
hello there...im having a major issue getting this thing to run for a second time. it ran for the afternoon, i shut it off, and it wont prime again. it now say E-07 in red, with a flashing red sign under the E letter
@Jackkamerun3 жыл бұрын
great video!
@SamsMotors3 жыл бұрын
Thanks!
@hawkkim19744 жыл бұрын
this is people's technology!
@kylefrench8944 Жыл бұрын
Is there a difference way to do this with the black remote I’ve tried this way with the black remote and it doesn’t work
@zheneggmobile4 жыл бұрын
my unit came with the black lcd but no remote. does anyone know where i can get just a remote that will work with it andnot have to buy a whole new controller? great little video, thanks
@leonzios105 жыл бұрын
Ok so one thing I noticed with these blue controllers is that the timers are not the same as the black controllers. You are actually setting the amount of time to when the heater will turn on. So if you leave it set for 99:99 it will actually turn on in 99 hours and 99 minutes from when the timer was turned on. Then that timer will shut off. The heater will run continuously until you shut it off manually. Real big pain in the ass. But just a heads up to everyone.
@eanluck21425 жыл бұрын
Did you ever find a way to change this setting to daily timer ?
@TheFlybyman Жыл бұрын
Thanks!
@martinmorgan8475 Жыл бұрын
Hello just got 5 kw heater red all in one blue screen black controls, when I turn it up to 5.5 kw it doesn't seem really hot, is there a way of increasing the hertz or making it run hotter or which option turns the heat up, thanks
@cinek3013 жыл бұрын
i got the same lcd and I can't change the pulsing thing for Celsius i tried shit load of combination and nothing. how do you change it in this model? settings simultaneously with left? heeeeeeelp😤
@ranchdude43454 жыл бұрын
BIG SAM...""""HELP""" what battery's go into the RED remote you were using??? Make, mod. #, voltage. not find info. on them ANYWERE!!! Thanks.
@SamsMotors4 жыл бұрын
As far as I know, they are just normal AA batteries!
@ranchdude43454 жыл бұрын
@@SamsMotors Thank you very much, but I do believe that they will be AAA.!! I just found out. Thank u once again.
@cliffordjava46584 жыл бұрын
Great vid. I have a question. How can I adjust the screen's brightness, if possible? Thx
@lionelp19442 жыл бұрын
Can't figure out how to change it from the Hertz to the temperature
@TheHybridCamperGuy2 жыл бұрын
So you know how to switch the remote from Celsius to ferenhigh??
@pwtwsw4 жыл бұрын
Hello, how to change the Chinese language on the remote control to English?
@MrFrodo11113 жыл бұрын
Did you figure how..I'm having same issue
@user-go4un7wo8j10 ай бұрын
How do I get my remote control from manual to automatic ?
@traceypurcell26875 жыл бұрын
Thanks for putting up the video awesome job!
@SamsMotors5 жыл бұрын
Cheers for watching! Another one coming next week of the full install into my truck.
@absautorepairs79404 жыл бұрын
we managed to set it all up was simple man of your talent would do it half the time
@lloydmorrison59793 жыл бұрын
Thank you so much for this video. The translation from Chinese to English is very confusing!
@slammedresto4 жыл бұрын
I have the blue controller with red remote, I am using a Hulk marine tank which has the fuel line coming from the top of the tank, where the supplied 5ltr came from the bottom. I am following your instructions as I need to prime it, but I can't get the controller to prime. Im doing what u say in the video, but my controller doesn't bring up the H.
@fourbyforester Жыл бұрын
thanks for this video. Odd question: would it be possible to set the bluetooth off totally in the machine as well as in the remote?
@herbjones4458 Жыл бұрын
Does someone know mine won't purge or go on I hook it to Is my 12 V battery It says P14V Has a picture of a little battery And has a red circle with a red negative sign In it I thought maybe Had it reversed positive negative The control would not even light up Anyone to help me
@MekMe66 Жыл бұрын
Hi. W What is the maximum distance the remote control works?
@sweetsweetmuseek4 жыл бұрын
Hi Sam, great video. I've got the same unit/control/remote. I've paired the remote but struggling to fathom out how to change temp on both the unit and the remote. There's manual, set oil flow and temp on the left side of the lcd screen, when I press OK it alters from temp to oil flow etc. But doesn't allow me to alter temp. I'm not technically minded and struggle with gadgets, so not sure what I'm doing wrong. Also the hertz can be adjusted via the ok/up and down but when you do the same for temp it changes screen directly back to hertz again. Quite confused.com
@SamsMotors4 жыл бұрын
Hi, thanks for the comment. It sounds like you've not changed your controller from Hz mode to temperature mode. Try pressing the 'settings' and 'up' arrow at the same time.
@petrimuinonen34622 жыл бұрын
Hmm, mine seems to only show ambient temperature and set oil flow rate🤔 Really wish i could also see battery voltage😥
@nigeljwoolley1858 Жыл бұрын
Try filtered used engine oil and diesel 5050 mix even better
@yxcvmk Жыл бұрын
Finally a connected remote. Thank you! Do you know if it's possible to set a (low night) temp on the heater, let's say 12°C, so that the fan and heater will only start below 12°C, and turn totally back off above?
@SamsMotors Жыл бұрын
The thermostat on the digital controller won’t ever actually shut off the heater fully - it’ll just reduce it down to minimum power once temperature is achieved.
@andrewskyes9956 Жыл бұрын
Bro I need help, i've done everything you did in the video but when i start it it shuts down after 5 sec. and comes back on..
@andrewskyes9956 Жыл бұрын
also the red plug doesn't appear on screen when i power it on, could it be from the power suply.. it has 12V 1amp
@SamsMotors Жыл бұрын
Hi Andrew, 1 amp is nowhere near enough power for one of these. 10 amps would be my recommendation.
@andrewskyes9956 Жыл бұрын
@@SamsMotors yep that was the issue thanks
@FWCaptain-kv6sm4 жыл бұрын
mine have no phone signal icon?my remote doesn't show any info, temps,etc? Humm?I got it! thx man
@gianvigaltarossa78984 жыл бұрын
Hello Sam. Really helpfull video, true. A question : in your knowledge the blue display is equal to red/gold display, changing position of the buttons only? Also the trick to use oil pump alone? I get a red one, but with zero instruction. seems equal, more the Altimeter and a sign for fuel, that i don't understand how it could works. tks for your time.
@SamsMotors4 жыл бұрын
Hi, thanks for the comment. Yes - as far as I know, the gold controller is the same functionally as the blue one.
@wibokats1613 жыл бұрын
thanks for the video. question how can i change the laungauge on the remote its now in chinees?
@goranvuletic88734 жыл бұрын
Great! Thanks!
@mumtiTV4 жыл бұрын
How do you change the temperature to Fahrenheit? I tried the parameters PF1 to PF6 could not tell what they are for? Original password code was 1668, anyone has a link to an actual User Manual guide? Thanks.
@mark72185 жыл бұрын
hi I have brought this heater package could you tell me what im doing wrong because I set the time and set the start time and pressed ok and it goes straight to the second set time rather than off time , could you enlighten me please on what im doing wrong thankyou , Mark
@alanbrown71555 жыл бұрын
I have the same heater as you the same panel but 2 button remote. Can't seem to pair the bloody thing. X thanks.
@mr.invisible58743 жыл бұрын
Damn, CUTE GUY!!! Thx for the info
@SamsMotors3 жыл бұрын
Thankyou, glad you found it useful.
@desertbreeze16205 жыл бұрын
I have ordered a similar unit as my 110 does not have a heater (ex Oman army trucks were delivered without heaters). I was planning to install the heater under the seat in the battery box with one duct under the car to the bulkhead entry to the dash and the other duct through the battery box into the cabin at low level. Do you think this is a good plan? Do you think 5kW is enough heat for when the truck goes back with me to the Cheshire Countryside? Thank you for sharing your expertise with us!
@SamsMotors5 жыл бұрын
I like the idea of feeding into the original heater inlet - means you will have control of hot air onto your feet or onto the windscreen (assuming the dash has the correct controls and ducts etc)... Quite a long run of ducting to get it there from the seatbox though... it might be worth insulating the duct with some pipe lagging or exhaust wrap or similar, as you'll probably lose quite a bit of heat, especially when on the move and you have lots of cold air rushing past it. 5kW should certainly be enough power - it'll definitely be hotter than a standard Defender heater anyway.
@syncrovanCos5 жыл бұрын
@@SamsMotors I had pretty much same idea in mind, for my VW T3, since it's difficult to keep it warm while driving, but have no idea how to connect this heater with original dashboard heating tubes, without damaging something. Is this even possible ?
@dikran644 жыл бұрын
Anyone know how to get the controller on the end of a long extended wire?....mine controller is at the end of a very short wire.
@jasonparsons814 жыл бұрын
Hi thanks for this video. Very helpful and we'll presented. Mine was working fine for about two months but now when I try to set the timer on and off its not working how it should It allows me to set the on time but then when I go to the next option 2off it doesn't allow me to input a time , it just goes straight to the pin lock option?!! Wtf is happening here?? I sat for hours pressing all different kinds combinations to try to resolve it but no joy man :( Is there a fix for this that you know of please I'd be so grateful for any help . Many thanks Jason
@gilliancowan35175 жыл бұрын
Hi Sam Just installed ours after being reassured by your vids... is amazing. I can’t pair the remote though as I don’t know how to change the language on the remote. Can you advise. Oh and really fab vids. So informative and clear 👍🏻
@SamsMotors5 жыл бұрын
Hi Gillian, thanks for the comment :) Hopefully you have managed to pair it by now, but you should be able to change to English by holding the OK button on the remote for ~5 seconds. Unfortunately I have seen on the Facebook group that some people have been unable to change their remote language - so I presume that some have been manufactured with Chinese as the only language. If that's the case with yours I suggest you contact your eBay seller and ask for a replacement English remote or a suitable refund.
@nomadchad82435 жыл бұрын
Hold the OK button for a few seconds. It switches back and forth.
@sinisas.22485 жыл бұрын
Can you tell me can I get out thermometer from controller, because controller is in cabin and I heat cargo hold in a van? So I can see which temperature of heated space on cotroller in cabin.
@tomaszposobiec57185 жыл бұрын
Hello, I have identical webasto, but I can not set the activation of heating at a specific time (alarm clock function) you can suggest something, record a movie can do something wrong. Regards
@kacotr273 жыл бұрын
How do you change from Celsius to Fahrenheit?
@Batemarrmb5 жыл бұрын
Hi I have the black LCD type when I set the time and go through the settings it does not store the time it goes back to 0000
@JayHughart4 жыл бұрын
I have the same red remote and it only displays temp set and ambient temp. no case temp or voltage anyone know whats wrong?
@barbaraflanigan16414 жыл бұрын
Does this model have a thermostat where you can set the temperature and the heater will seek this temperature by running faster when it is colder and then slowing down and idling as the temperature is reached? All I can see is that when you change the temperature, it changes only the fuel pulse cycles to feed more fuel or less fuel.
@SamsMotors4 жыл бұрын
Hello, yes that's possible. The temperature sensor is in the control panel.
@phillallen013 жыл бұрын
Hello sam ive had my heater for near on 5 years now ive replaced the controller 3 times and the main board twice and pump iam on my 5th but today its pack up again all works untill pump is supposed to switch on but it dont swit h on it displays it on controller but no action if i prime the pump it primes but when it comes to actual use not fireing i was wandering if it the main board again or controller
@SamsMotors3 жыл бұрын
Hi Phil, that's a strange one. I'm wondering if it might be the glow plug this time, as it won't start the pump until the glow plug has successfully heated. Is it giving you any error codes?
@phillallen013 жыл бұрын
@@SamsMotors yeah its E08 i managed to get it fired once today for about 10 minutes then it packed up again the glow plug works i managed to prime the pump then switch on and it blow out white spoke then die again after fuel ran out in heater as pump would still not fire
@buggzo3 жыл бұрын
Will the thermostat autoregulate ambient temperatures in my van?
@leonzios105 жыл бұрын
I bought a kit that came with the exact controller you have but no remote. Is there a place I can buy just the remote? I seem to find the 2 button no display ones quite easily. Thanks for the videos btw. Good stuff.
@SamsMotors5 жыл бұрын
I’ve not found anywhere selling the red remotes on their own. I’ve contacted some suppliers on Alibaba but they too only supply the 2 button type.
@hanschristianweinreicholse5095 жыл бұрын
SamTheSuave Can you buy the controller together with the Remote , please let me know
@marineswarm4 жыл бұрын
can you change the language? mines in Chinese
@Hilmi123 жыл бұрын
Press and hold OK button
@MrDavidcarp5 жыл бұрын
Thanks man
@hanschristianweinreicholse5095 жыл бұрын
can not get the timer to work, the clock is set correctly, but it does not start? Please help me,,,
@eanluck21425 жыл бұрын
Did you sort this as seems can only set as like a stopwatch rather than a daily set time ? I am hoping it can be changed in a setting somehow .
@winandd86495 жыл бұрын
Having the same problem, i can only set a "wait delay", after which the heater starts.. It does not accept a start and a stop time. Did you solve this? How?
@winandd86495 жыл бұрын
@@eanluck2142 Did you solve this? Please share, I'm having the same issue..
@gsxr4192 жыл бұрын
My remote says waiting but never turns on
@huwarlow61922 жыл бұрын
Hi, any idea how to change the language on the red remote to English rather than Chinese please?
@offgridexplorers9514 жыл бұрын
Hi Sam. My van has a webasto heater fitted. Do you know if the Chinese lcd is compatible with the webasto? Thanks in advance
@scottbeale18252 жыл бұрын
how do you adjust the fuel pump?
@jeremywaller64115 жыл бұрын
Hi there. Thanks for the video, very helpful. Just got mine running for the first time tonight. I don’t get the option to set the target temperature, after showing the current room temp it shows a hz number. Can you help?
@peterstaples79454 жыл бұрын
That's actually the down button on the right. But pressing the settings and left arrow does nothing, but switches mode on the old controller
@johnysilver18532 жыл бұрын
Does it have low voltage protection in case battery charge goes low so heater will automatically turn off?
@SamsMotors2 жыл бұрын
It does, but I still wouldn't use it on a starter battery.
@showmequick22455 жыл бұрын
I have not seen any listings with that remote. Could you please post a link ? Thx
@SamsMotors5 жыл бұрын
Hi, please see the link in my other video (Unboxing & Testing). Thanks
@showmequick22455 жыл бұрын
SamTheSuave thx
@randydicotti39753 жыл бұрын
The screen on mine is nearly invisible unless viewing it tipped up at about a 45 degree angle. Straight on you can't see anything. Annoying.
@bluefire87HN5 жыл бұрын
Thnaks!!! But i can not switch the automatic and manual mode.
@japguns10224 жыл бұрын
I know this may be a bit late... But hold the up and down button at the same time... It will switch modes.
@elibaxla57275 жыл бұрын
Great video! Can you change the settings from Celsius to Fahrenheit on the new upgraded display?
@SamsMotors5 жыл бұрын
Not as far as I know.
@rayhughes82405 жыл бұрын
Hi Sam, Great video mate. I noticed someone else has this problem, how do you change from automatic to manual mode please?
@Whitmeister85 жыл бұрын
Sam, thx for the great edit. I'm just bench testing today and you got me through the confusing bits. I have paired the Red Remote but the text is still in Chinese.. any advice?
@SamsMotors5 жыл бұрын
Thanks for the comment Whitney, appreciate it :) For the remote, try pushing and holding the OK button until it changes to English.
@Whitmeister85 жыл бұрын
@@SamsMotors That worked, thx.
@Juke1724 жыл бұрын
SamTheSuave thanks! This is already better controller than the one with only the knob on it.
@alanbrown71555 жыл бұрын
Hello there bud. Can you show how to set temperature from the control panel it's self. A have exactly the same unit & control panel but without the remote. I can't seem to find temperature control on the panel itself. Thanks.
@Whitmeister85 жыл бұрын
You should be able to adjust temperature by pushing either arrow.