Chinese-sourced vintage chips, real or fake?

[@ksbs2036]

Yeah, given that I was doing a fair bit of work in VLSI in the late 70s - early 80s I was kinda expecting to see I^2 L (I squared L) in the clock chip. I2L is very low power and a lot of watch chips used it back then. CMOS was very much in its infancy in the early 80s and the working voltage was too high (over the 3v of two watch cells) back then. Really fun video

[@BlackEpyon]

Did you happen to be involved with making any of the VLSI chips that Tandy used?

[@ksbs2036]

@@BlackEpyon , sorry no I wasn't. I was a research assistant at the University of Waterloo's VLSI group. We were figuring out how to design them. The chips were following Moore's law so the capability to make lots of transistors was outstripping our ability to make designs with lots of transistors ...

[@BlackEpyon]

@@ksbs2036 The reason I asked, is because the VLSI chips on those retro computers are pretty much black boxes. The service manuals told you what was in them, and the pinout, but not the schematic diagram internal to the chip itself. They were pretty reliable (I've never seen one go), but if one happened to go, you'd have to find a donor board to salvage from, 'cause there's no way to replicate them.

[@DanaMyersK6JQ]

These are more early-mid 1970s vintage, right?

[@VintageTechFan]

Working voltage too high .. Wasn't that the case for MOS in general at first? I mean, early NMOS and PMOS chips ran at basically 17V, the +5V/-12V for PMOS and +12V/-5V for NMOS were only to get (somewhat) TTL-compatible logic levels? The 4004 for example doesn't even have a "GND" pin? The couldn't implement depletion mode FETs on the same die as the enhanced mode back then, so that the current source FET used considerable voltage if I understood it correctly?

[@Lilithe]

I love when people document these black boxes.

[@TheDiveO]

next episode: Master Ken rebonding the Chinese chips and Chief Antoine baking them into new packages, so they can use them as spares in the future or sell then on the "Interweb".

[@1944GPW]

Send the dies to Sam Zeloof as a challenge. If anyone could repackage them back onto a DIP, he would be the most likely to succeed :)

[@manuell3505]

11:45 I guess he wants to keep the original hardware, but wouldn't it be possible to emulate the clockchip output bits correctly with programmable logic?

[@johncrowerdoe5527]

@@manuell3505 Not many programmable chips matching the peculiar voltage and power characteristics. That said, back in the day Ti had an official digital clock chip with LED drivers, apparently based on a mucrocontroller. It was used in at least one magazine published "build your own digital clock" project.

[@lwilton]

Strong suggestion from someone else that has had fried chips due to OV when the battery dies and goes open: put a zener or forward biased diode string across the battery or chip Vcc voltage to keep a future battery failure from doing the same thing.

[@CuriousMarc]

Exactly. I really wonder why they did not do it. Maybe worried about the extra leakage current and wanted to keep it at an absolute minimum?

[@lwilton]

@@CuriousMarc Possibly. Since that lack seems to be endemic to this sort of stuff no matter who made it, I more think that it somehow just didn't occur to the engineers that the battery could fail, or maybe it got cost reduced out by a manager. On the other hand, low voltage zeners have really sloppy regulation curves, and might well draw significant standby current at 2.5V. A stack of forward-biased diodes might be a better choice. What's the charging voltage on those batteries? It must be more than 2.5V. Hopefully a clip around a half volt over the charging voltage would be safe.

[@simondann7371]

l wilton I reckon it was assumed by the time the problem occurred the product would be end of life.

[@nophead]

@@CuriousMarc I expect the charging circuit might feed the battery with a diode, so it doesn't drain it while off. In which case you could clamp the other side of the diode and not increase the leakage while off.

[@ferrumignis]

Low voltage zener diodes are effectively useless for this kind of protection as they have such a soft knee. This means it either clamps at a higher voltage than you want or you have to accept a considerable leakage current at the nominal voltage.

[@lorenzoporciani]

Maybe the problem is how they get those chips, while doing that destructive process that is documented somewhere on KZbin (they take a board, pass it on a puddle of molten solder and then slam the board against a surface until the chips break lose) the bonds to the silicon bit break, or maybe ironically they are taken from the same boards as the one you're trying to repair and they are already zapped 😂

[@mitfreundlichengrussen1234]

Thanks for making my day. It is simply fun to watch professionals at work. What a pleasure and yes: I have learned a lot again without ruining my own stuff.

[@GoldSrc_]

It's always great to see chips under a microscope, can't wait to watch the next one.

[@dave68]

Yes, and I for one would love to see the "Donald Duck" drawings, and the like, on the edges of some of those chips. Bored engineers.

[@SiggyPony]

I've brought hundreds of older chips from China. I normally stick to the same few suppliers I know a reliable. I've only ever gotten a batch of fakes once once I let the seller know they pulled them from sale and sent replacements, I still buy from them today. That time they got sold fake chips from a new supplier.

[@64bittz93]

Is there any chance you reveal your trusty vendor?

[@alpagutsencer]

These videos are definition of perfectness. All of them are really made my day. Thanks for the team and you. Please continue sharing.

[@pinball30]

I would start looking at the traces etc where the batteries leaked on the boards. This is very common for early digital pinball boards, we have found some very creative ways of fixing it.

[@DouglasJohann]

"It took master Ken only 2 clock cycles to identify some very unusual 1970s IC technology." lmao only 2 clock cycles that was fast

[@UnitSe7en]

Not necessarily fast. It depends on the speed of the clock.

[@DouglasJohann]

Well you got me. You're right!

[@volo870]

Now we know that Ken is hardware-optimized to identify unusual 1970s IC technology.

[@madmax2069]

@@UnitSe7en I was going to say the same thing

[@eloyex]

Ugmmmm ......... Ken seems to be a Schottky fast dude. .....!!!.

[@jackdaniels8898]

Can’t wait for the video about how you test the HP RTC module and if none of the chips work how you emulate the chip in an FPGA or Arduino. Grabbing the popcorn 🍿

[@bluef1sh926]

"FOCUS YOU FAC!", one old canadian proverb says

[@jpolar394]

AvE........😆😆😆😆😆

[@KameraShy]

Check out those vintage Friden's in the background! Mechanical calculating machines. Used them in college and first job before electronic calculators came on the market.

[@CuriousMarc]

This playlist has the videos about the Fridens: kzbin.info/aero/PL-_93BVApb5_GbzkFwdKpuyPo8Ty83h8b

[@albinklein7680]

'I want to control my HP power supply in style'. There are only three things in life that really matter: Style, style and; of course; style!

[@DonnyHooterHoot]

I've tried this die removing technique and I always crack the die! I'll keep trying

[@dave68]

Practice, and patience...

[@jkenny1]

You can try sandpaper and a lot of patience too. Start coarse and work your way down, like polishing. Then scrape off the last part with a plastic spudger. I've got a video on my process on my channel.

[@MattTheComputerGeek]

In Chine they have factories where they will take old chips from recycled electronics and lazer etch the surface of the chip to make it look new and change the printing on the chip to make it look like the newest version of said chip with the newest firmware. Then they will sell them as new old stock etc, when they are old used, and may not work.

[@pahom2]

Dr. Ken should write a guide of how to identify a chip production date based on its technological features. With illustrations.

[@windmill1965]

I2L logic? That brings back memories. When I was a university student (some 30 years ago) I had to work a couple of months on a project for a semiconductor company. The project consisted of creating simulation models for I2L building blocks by parameterising test structures. So it was analogue work, resulting in a digital simulation model. I2L logic was preferred as it was used for small digital control blocks in otherwise entirely analogue bipolar products. The wafer technology was bipolar, so MOS logic was not available in these mixed signal products.

[@manuell3505]

So you measured the behaviour of existing circuitry to refine your own product? If it was from a different manufacturer who was unaware of it, isn't that reverse engineering?

[@windmill1965]

@@manuell3505 The company had an in-house simulation tool. Which could simulate for example the influence of supply voltage, temperature or deviation in manufacturing accuracies, in the performance of I2L logic. The accuracy of the simulation results depend of course on how accurate the simulation model is. So the characteristics of the pn-junctions and the transistor behaviour were measured using special test structures and then used as parameter settings in the simulation models. This is the work I had to do: measuring those test structures, finding the correct parameter values, and then verify the simulation results with actual I2L performance. It had nothing to do with reverse engineering chips from other manufacturers.

[@manuell3505]

@@windmill1965 Allright, that's just an independent research/production circle.

[@dosgos]

"So at one point, I wanted to flex even more". Too funny!

[@wolvenar]

What are the chances that the Chinese were real, but toasted in exactly the same way?

[@petergorelov418]

Actually, I thought exactly the same ;)

[@MrFathead]

That was my first thought. Since the chips appear real and the fault it so common it would make sense. We will have to wait for them to make a test board to find out but my money is on the chinese chips being faulty.

[@Membrane556]

I was thinking the same as they're probably pulls from recycled hardware. Too bad HP didn't add over voltage protection circuitry for the chip. But then they probably figured the battery would last longer than the service life of the equipment.

[@Troppa17]

@@Membrane556 Exactly what I thought. They pulled the chips from faulty HP RTC moduls or other HP equipment. Maybe they simply didn't know about the problem and assume the chips were working.

[@Broken_Yugo]

Very high, it's my understanding all these vintage chips out of China are at best pulled from scrapped gear and sold with no testing, maybe erase the EPROMs. At worst they remark them as a faster or more favorable variant.

[@8-bitbitsa821]

If memory serves me... I2L was way more prone to static discharge damage, more so than even early CMOS ?

[@ksbs2036]

I don't believe so. It is a bipolar process so it doesn't have the gate insulator that gets destroyed when E-field go to a million volts per metre. (1 volt across a micron)

[@SeanBZA]

It was a lot more sensitive to process errors though, especially in the early days of IC manufacture, as it relies on barely turning diodes on and off to do logic. Power hungry as well, so those early wristwatches had a very short battery life, even if you did not turn the display on.

[@SeanBZA]

@@MikinessAnalog IRFZ44 likely has, in addition to humongous internal capacitance in the gate to absorb ESD current, a set of zener diode clamps to limit gate voltage. The clamps are around 20V, so they do not otherwise affect the decice in operation, and the capacitance is why the drivers need to be so robust if you want fast low power dissipation switching. DC to a kHz you can use a regular logic gate drive, but for higher frequency the current peaks required increase quite a bit.

[@Gerardus1970]

They don't make fake chips like this, they recover, clean, sand and remark chips to be sold as new.

[@gkasprow]

they sometimes use low-grade opamps marked as precision ones. They also make functional copies of popular chips - search for "FTDI chip gate"

[@Gerardus1970]

@@gkasprow Yes, and a lot got caught out by that too, bricking their devices.

[@BreakpointFun]

in shenzhen, they list every chip online, when an order comes in, they write the correct name on something with the same package, sometimes a close model number, or shorted out, or sometimes reprogrammed years ago a us pilot's ejector seat did not work, and they concluded it was fake chips. manufacturing only tested some of them, and did not see any bad chips😢

[@wolvenar]

It should be easy enough to build a replacement that plugs right in with an Arduino. Sure I get the idea of keeping it original, but at some point...

[@bborkzilla]

I wonder if a small form-function board could be designed around a small microcontroller to fit into that socket. Perhaps not the usual AVR or PIC, but maybe an MSP430 with its LCD drivers adapted for this sort of usage.

[@GusFernCa]

If you decap a chip that has been "zapped" by 2X overvoltage, would the damage done not be obvious when viewed under a microscope?

[@dave68]

@CuriousMarc were the chips zapped? We couldn't tell from the microscopic images.

[@jean-baptistelasselle4562]

love the noise of the computer starting :D 4:17

[@campbellmorrison8540]

Brilliant analysis as usual but I have to say I cant imagine any Chinese copier being able to make a chip like this with such limited resale. I decapped plastic chips many years ago when running a thick film lab and the New Zealand department of scientific and industrial research laboratories and have a very reliable method but I cant find the paper I used to make my version. I am truly surprised it isn't used these days, It involved boiling nitric acid but it was very safe ( as far as nitric acid goes ) and worked incredibly well. I can explain it etc but I would need to give you drawings etc so I would need to talk direct via email if you are interested

[@SoddingaboutSi]

Marc, i think we have a hp9825 at work? If its available and that model and isf so would you like it? Will check next week.

[@maicod]

is master Ken actually human 😂

[@CuriousMarc]

I have my doubts.

[@jimmy_jamesjams_a_lot4171]

In the scene where you were explaining this cartridge with the battery and chip that you wish to replace, there is what appears to be an old white ceramic ic, a really large one. Would your friend’s ‘heatgun and break in’ style of retrieving a die be as reliable on these older heavier ceramic styles of ic? I’ve noticed that those ceramic ICs often have layers sandwiched together and those layers are different shades of grey, brown, white, and black. As usual, great stuff, you make some really educational content, while really keeping with the entertainment factor, at least for independently produced and as close to reality as it could be!! Thanks again!

[@Patchuchan]

Since it's remote piloting a watch could another clock chip with LED drivers be adapted or a uC programmed to emulate it?

[@bertholtappels1081]

Fascinating. You do magnificent content. Thanks for taking the time to share your passion.

[@davidmaddison2628]

Just a suggestion, have you tried contacting TI to see if they can help you?

[@johncrowerdoe5527]

Great idea, Ti is keeping lots of old designs available as normal stock numbers, so they may well be keeping other historic chips on file or in stock, but on request only.

[@NurdRage777]

This is what I wanted to do. I did a mod on my phone camera with a 8mm or 6mm CCTV camera lens and I was able to decap my bank reader IC and made a low res photo of the die !! Never would have imagined this was possible (few years ago). But now I want to know as well. I brought TNY180 power switch ICs for dirt cheap. Are these ones real or fake?! Maybe I decap a "new chip" and try to compare this with the half burnt up chip. Maybe I can see similarities ?

[@ironman7261]

I remember the Soviets would copy US processors right down to the manufacturer name on die so not a guarantee it is original. If their is a market for them they will do it

[@genetomblin2883]

At one point the Soviet's were having agents purchase speak and spells to take home to copy chips. Many of these chips were copied including the manufacturers logo on the Soviet clone. They were that far behind that Toys R Us was a source for tech that did not have.

[@noelj62]

I put my thinking hat on before watching... Intriguing investigation work. Good job all.

[@chriholt]

Can't wait to see the next chapter in this treasure hunt!

[@__-nd4hf]

11:11 your comment about cleaving silicon got my attention. Want to add that it is hard handle because of how brittle it is, but it is not hard to cleave. We usually mark the silicon with a diamond pen and just shear it off, putting it on a paper clip. Cleaving sapphire or silicon carbide wafers is way harder. P.S. Will Master Ken reverse engineer the circuitry of this chip?

[@thebigpicture2032]

Yes, silicon cleavage does get one’s attention.

[@eloyex]

hehehehe , love the "Master Ken". comment ... the guy deserves respect !

[@VintageTechFan]

@@thebigpicture2032 Google gets many search requests for this particular thing, though. Mostly from us Germans ;).

[@Nimmbin]

Lol potato vision. Sir... I do believe you have introduced a new visual standard of awesomeness 🙂

[@ScienceAppliedForGood]

What's left is to plug the Chinese chip and hope for the best... which is kind of saying PnP MS technology, Plug and Pray.

[@williamsteele]

Oh cool... just randomly was notified of this video and there I see the 1820-1691 nanoprocessor or in it.

[@williamsteele]

Handwritten voltage of only 2.5v... wow!

[@cowboyfrankspersonalvideos8869]

I'm no expert, but could the Chinese seller have somehow gotten hold of a bunch of chips that TI dumped because they were defective?

[@sittingstill3578]

I heard in an _Adrian’s Digital Basement_ episode that many of the authentic chips from China were acquired through e-waste processing.

[@LaurentLaborde]

lucky guys with a reflected light microscope !

[@3vi1J]

Insanely interesting! Thanks for sharing!

[@pulesjet]

Those watches sold for like 5 and 700 dollars at one time.

[@wolvenar]

@rustybuttpate I had nearly the same experience. Damn....we are old now aren't we?

[@agentsmithisalive]

Reminds me of circuits that blew the SCRs or TRIACS in order to protect the fuse. :_)

[@wesleymays1931]

Maybe blowing a BGA LED driver to save the fuse?

[@annaoaulinovna]

what a great scope.

[@nrdesign1991]

My oh my - they did NOT think of including a cheap-arse 2.5V Zener diode to protect the chip whenever the battery goes open-circuit? Either penny-pinching in the wrong place, or just plain ignorance.

[@CuriousMarc]

I think neither. They probably could not tolerate the Zener leakage.

[@andrewallen9993]

@@CuriousMarc And if it was on a maintenance contract your friendly local HP customer engineer would replace it at every PM. If you didn't have a maintenance contract it would cost you an arm and two legs for it to be replaced and serve you right according to Bill and Dave :)

[@gavincurtis]

Perhaps a 3-4v zener (or couple of LEDs in series) across the battery so it can never go to 5v again? Surprised the original engineers missed that.

[@davebing11]

the leakage current is waay too high to use zeners or leds. .

[@ZiggyTheHamster]

The way these Chinese chips ended up in your possession is that someone dropped one of those modules into an e-waste pile and then someone in China desoldered the chip and cleaned it up and put it back on the market. Nowadays, anything sold as "new" or "NOS" from China is actually re-marked old stock, so don't trust it. If this is a common fault, the chips you bought were almost certainly dead too. You'll probably have to figure out how to engineer a modern replacement.

[@Beatnik-Manor]

More than likely Dismantled in india and sold on to china

[@andrewallen9993]

@@Beatnik-Manor You obviously frequent the same places in Bengaluru as I do when looking for bits for keeping old plant electronics alive :)

[@redoverdrivetheunstoppable4637]

so i'm the only one that gets fake parts (transistors)... anyways the new chips may have been salvaged from a computer or else that have sockets for at least the RTC and may had the same problem with the battery, so fried as well

[@medes5597]

I get fake transistors too. Also I got fake resistors about a year ago - literally they'd put correctly coloured plastic on a piece of wire. I was like "what the actual fuck".

[@jkenny1]

The interesting ones are fake FETs I've bought that are fake, but still functional and similar characteristic. Must be made from a Chinese manufacturer to similar specification and just remarked for higher price.

[@redoverdrivetheunstoppable4637]

@@medes5597 i bought a 2500pcs pack of 1/4W and they were not metal film and not inside the 1% stated obviously, more like 2-3%, but i use em

[@redoverdrivetheunstoppable4637]

@@jkenny1 if they are fake they quite likely withstand less current, they put a smaller die inside and that's how they scam you, buying from a more costly seller seems to not solve the problem, weirdly they sometimes provide you good parts, so the price may be near to the correct one, i would be perfectly happy to pay 1.5X times the price but have good parts, another funny fact is that they CAN provide you LEGIT parts but without fancy brands, infact inside their gadgets they usually fit legit unbranded parts, i also found a custom made transistor, if you buy an high voltage module like the 15kV one, between the components there's a BJT with package TO126, but to copy the pinout of a TO220 that has been replaced for cheapness they made an unmarked, unknown TO126 transistor with pinout b-c-e like a TO220 that as far as i know doesn't exist, TO126 are all e-c-b, so they can make a custom transistor just to sell some junk modules

[@volo870]

Dear CuriousMarc, Can you identify the part of the chip that was blown by over-voltage? Just curious if the damage is visible under the microscope.

[@MrFathead]

I was thinking that too, it would be interesting. But it might not even be on the die where it melted.

[@CuriousMarc]

No, could not see anything obvious.

[@jkenny1]

Failure analysis is hard.. dealing with it at my day job. There a whole host of testing and analysis methods including thermal imaging and SEM. Fascinating stuff though.

[@volo870]

@@CuriousMarc, thank you for your reply.

[@andthe_tony]

Why are you asking me for? You’re the one that’s supposed to do the research for us so we can learn

[@VoidHalo]

I'm sure it's a bit more of a mundane topic for this channel, but I've always been curious about how prevelant counterfeit ICs are on aliexpress. I feel like every chip I've bought from there has had something fishy about it. Especially the 74HC595s where the TI logo is a picture of the United States lol. Guess they didn't know what Texas was. Still, in my day to day use I wouldn't suspect anything was off about these chips. But I suspect if I characterized the chips more purposefully I would find some anomalies compared to the datasheet.

[@ruffmansavageveteran1345]

Cool video. How come HP didn't use a voltage regulator with the clock chip?

[@davebing11]

the leakage current of the voltage regulators back then were well over 10uA which was way higher than what the clock chip drew

[@Ernest_More]

What microscope was used here?

[@LuxorVan]

Why not build an adapter that uses a smaller rtc like bq3285 ?

[@luminachiar7120]

Hello, mr.Mark please tell me what is that laboratory , where you are working?

[@VegasCyclingFreak]

Two thoughts: The Chinese ICs may have been pulled off a PCB and made to look new or they were genuine NOS but were improperly handled and died from an ESD.

[@ocayaro]

Let's take a moment to congratulate the Chinese on their ingenuity. It takes brains to do what they do.

[@Painless_]

I thought this video was going to be about old maps

[@lbochtler]

What would be even more interesting, is to see the chips working under the electron microscope

[@BlackEpyon]

Pretty sure that would make them stop working.

[@mumiemonstret]

@@BlackEpyon Applied Science does it with a 555 timer: kzbin.info/www/bejne/m6C1h3itasx_bsU

[@lbochtler]

@@BlackEpyon its a technique thats used to test chips. Though it depends on the technology if they can withstand it. Also, a proper electron microscope dose not destroy chips as easily as applied sciences hacked together SEM did, if you where basing that off of his video.

[@BlackEpyon]

@@lbochtler Applied Science got himself a proper SEM too. I was thinking more along the lines of the die being bathed in electrons and just washing out. It wouldn't be able to function WHILE it's being scanned, but should be able to function afterwards. I think.

[@lbochtler]

@@BlackEpyon The technique that is normally used is EBIC (Electron beam induced Current). You wont see it run in real time though, as you need to scan rather slowly. Yes, i know Applied Science has a proper SEM as well, but i dont recall him trying the microchip experiment using it

[@maciejjanicki8385]

Those chips are real. We've been sending our e-trash to China in millions of tons. In one time they noticed that they can do a business of rare chips. So they are desoldering parts, cleaning, straightening legs and even sometimes relabelling. Then selling via AliExpress...

[@I967]

Excellent content.

[@JohnDavidDunlap]

More like Grand-Master Ken.

[@erikas6874]

Much better to use X-ray when investigating chips. Easier to enlarge the picture too.

[@kaliban4758]

i know purist are going to hate this, but look into fpga, there are some brilliant hdl programmers out there

[@berczigabor]

Obviously the Chinese chips were removed from similar devices, and because of that just as fried as the original ones

[@waldsteiger]

mr. claunches idea of building a testing board being the pro thing, wouldnt it be fun to wire a star wars watch pcb into the hp machine?

[@davidjames666]

Not sure why i even watched this. I thought it was about potato chips, but it was about telescopes and stuff

[@alexpmK3]

Fascinating

[@lincolnmicrophonellc]

Decap and schematic for the Roland 106 chip on board ceramic proprietary circuit that Roland has no interest in reproducing or helping with? Would be many grateful people. Thanks great content!

[@chargehanger]

add a zener over the battery

[@dm4728]

Merci Marc super interessant, ce semble que le chinoise trouvé le die d'orgine?

[@CuriousMarc]

oui. C’etait une vraie.

[@dm4728]

Géniale, je chercher une IC obsolète, Reticon SDA1024A, malheureusement le chinoise ne fabriqué même pas de faux 🙁 (Désolé je suis Anglais mais j'aime bien de utilise mon language française des temps en temps)

[@CuriousMarc]

@@dm4728 Bravo pour le français!

[@pulesjet]

Brilliant Idea Sir.

[@DandyDon1]

It's too bad that it could not be retrofitted with something like an Oki 5832 Clock Calendar IC.

[@LetsPlayKeldeo]

Wow really interessting video !

[@phuzz00]

Can anyone explain the colour difference between the two intact dies? Could it be down to a very slight difference in the thickness of whatever coats it?

[@jankro1]

You did not have access to a James Bond chip comparator? 😂

[@dmytrodubovoy2923]

Most likely those Chinese chips came from the recyclers who got bunch of those old HP modules with the dead batteries, so the clock chips were not good in the first place. Those recyclers they will try to pull everything that seems to have value and sell.

[@CuriousMarc]

That’s what I feared too, but in a later episode kzbin.info/www/bejne/pqOZeYefjNeAo80 I built a LED watch chip tester, and they all tested good!

[@fbnx4219]

Can you recommend a microscope for doing work like this?

[@alexpaww]

Could you possible post a link to the decapping video?

[@CuriousMarc]

Here: kzbin.info/www/bejne/kILIeXuPf76KjtE

[@youkofoxy]

Some other video on KZbin suggest those chip are recycled, that means they have the same problem as your original chip. A.K.A: they are fried. Some of those chip are just pulled of the board and receive a "beautification" treatment to look like new. but are actually old chip with varying degrees of use and abuse pulled out of they board, sometimes in a very brutal away, package and ship with littler or no consideration to work condition.

[@isettech]

There are many contaminates that slowly diffuse into the semiconductor killing it over time. The contamination migrates faster at elevated temperature. It migrates even without power. Many warehoused parts are not in climate controlled conditions. When CPU's went to copper interconnects, it was discovered Copper is one of the contaminates. The process is very specific to copper plate and plane the ILD side of the chip while protecting the semicondictor side from copper contamination. Many of the vintage chips did not have the knowledge of the migration contamination failures until much later. Simple copper pipe used before water quality issues were discovered, resulted in chips with slowly migrating poison to the transistors. Contamination can be from the process with some trace copper contamination to die cutting, to packaging. For more info.. www.smta.org/chapters/files/Philadelphia_SMTA_Philly_Rev2.pdf

[@faidularcs]

Chinese one wafers bought from TI and they wire bonding in China maybe

[@Vesalempinen]

great videos. Please make compare video of US / USSR chip clones :0)

[@analog_music_lover]

they dont have to give you a fake chip

[@dtiydr]

2:23 To be HP that was some really bad design.

[@VintageTechFan]

Was quite common. Some portable tube radios had the same problem, the tubes in it were specified for 1.4V heating voltage and there was a single NiCd cell in there, which was recharged from the mains if used at home. If this cell did go bad or was missing, the voltage shot up and blew ALL the filaments. When this was designed, its quite possible that the people who designed it were still very familiar with this arrangement .. it was just 10 years ago that those radios finally got out of favour.

[@dtiydr]

@@VintageTechFan Well to see other brands do it wouldn't have been surprised, but HP have the best tech and should address it. Only a few components would have fixed it but they didn't even do that, no matter if it was 40 years ago or not. But who knows, it might back then have been and design thing to destroy it after some time.

[@tylerufen]

China has a different economy, you hear a lot of horror stories but that's just the sensationalism that makes its way to most people's ears... especially your hairy ears burned by tales of evil communism, but the reality is that Chinese people are very human, and as such when they look at old devices, here we see trash, but there they see something that's at risk of disappearing, and there's a lot of people there and a lot of people are paid to essentially do nothing, or do seemingly useless repetitive tasks, so a single person can maybe recover (idk) 250 chips from old boards, they get paid the equivalent of maybe US$5/day, and the individual chips sell for maybe $1/ea. so if the guy taking out 250 chips a day sells five a day he breaks even... with the economy of scale, all the hobbyists, and industries that still really on old machines, tech museums, basement collectors, and enthusiasts, well the guy actually turns a profit... Chinese business isn't like what we know, it's a lot less rigidly structured, look at Chinese corner stores you have in your city, they're rough around the edges, but the prices still beat the nicer, "cleaner" stores, and the cashier still makes minimum wage, except he's not required by contact to smile at you, and say hello when you walk in, he can just watch tv if he wants to... The guy who sells you the chips maybe has twenty or so small-time businesses, that's how the "mastermind" turns his profit, and lets people "below" him have a share of his success.... And your chips you get them off AliExpress or similar, and if they're fake you get a refund no questions asked, there's no money to be made in selling fake anything anymore, ... It's stories to get you to pay more for fake smiles and making some student feel like a whore and a slave at the same time, having to wear a uniform, shave, and even get a haircut just to keep his minimum wage job... If you look on Facebook at say Daily Dose of Satisfaction you'll get a real look at inside Chinese factories... It's not at all like what you might imagine.... China deserves the place it has today, and they did make sacrifices, but humanity, and respect weren't one of them....

[@Konecny_M]

Fun fairytale, but the fake chips industry mostly revolves around sourcing the cheapest surplus that visually matches the package (and if it is discrete or trivial function then even that), removing the original marking and remarking it as the high priced commodity or obsoleted part in demand. Recycled originals are relatively rare to come by.

[@andrewallen9993]

Correct, its like parts for my 60 year old diesel Heckflosse, parts start off expensive (buy from Mercedes) get cheaper (buy from scrapyard) then get expensive or really expensive when the device is old (buy from scrapyard or Mercedes)

[@donmoore7785]

I saw a video where some guys working in horrible conditions remove chips from boards, and the chips are then repackaged to make them appear new. Could it be you got recycled failed legitimate silicon in new packaging?

[@CuriousMarc]

I looked at them closely again, they appear to be, new old stock, genuine chips. If they had been in some previous equipment, then they were cleaned up very well.

[@Madmax23419]

why not test the chip without any other circuit on breadboard instead of killing the chip and still not knowing if the chip was working in the first place. :D Next chip can be a fake one and let you think that your board is broken or some other chip is broken, there is no guarantee that the next chip isn't a fake. Often the old rare components of ebay(etc) are broken, they are real but broken.

[@CuriousMarc]

That’s the case for this one apparently. Real but broken.

[@prokrastnation6071]

Please see this for additional info and a thorough tutorial on the repackaging and recognition of used vintage chips: kzbin.info/www/bejne/oWiVhHl4hL-Sotk

[@Mr.Leeroy]

13:07 why is one mostly green, while the other one is yellow?

[@CuriousMarc]

Probably the thickness or composition of the passivation layer on top is different.

[@abc-ni9uw]

CM PLEASE DO CRT VIDEOS

[@macelius]

What google engineers do in their spare time.

[@DJP-ph7yj]

Why invent your own chips, when you can steal everyone else's intellectual property.

[@dtiydr]

If the chinese can earn a lot of money on a rare sough after chip they can absolutely fake them, a chip like this is not the case so I would have been surprised if they were fake.

[@dtiydr]

@@1pcfred Such assholes. I know fex there is OSD chip that is quite expensive but very good so everyone use it. One day some individual discovered that if the chip he had was clocked at max speed, which they should handle with no problems and are made for, they started to malfunction really bad. People found out that they were of course fake and that they just contained a programmable AT328 cpu inside that mimic the real deal. It worked fine as such but not a max speed.

[@Membrane556]

I wonder could a micro controller be used to emulate this chip if you can't find any good ones? I think an ATtiny or Pic might be able to emulate it and even run off the existing voltages.Another crazier ideal hack a different watch chip onto an IC socket though most use LCD displays.