DIY Auxiliary Power For Your ACCESSORIES! + Installing LED Lights w/ Switches

[@nikyrabauliman3715]

As a new Tacoma TRD owner myself, shoutout to you Ms. Chloe for providing very informative and detailed methods & recommendations for upgrading and up-keeping, Mahalo!

[@azadaranda5634]

Hammer the edge of the tan to a 45 degree angle to increase clearance We do it in all sorts of stuff especially on truck (18wheels) tire valve rims to be able to air them up They have metal stems

[@alanworks4354]

Excellent video! I would like to add that you need to fuse for the wire. IOW, if your wire is rated for 8 amps, but your fuse is 10 amps, the wire will catch fire before the fuse ever blows. Luckily, 16ga wire is rated for 13a. You might also look into using car audio power wire. It has higher strand count, is a lot more flexible, and less likely to corrode over time

[@JTerry-zl5un]

Thanks for your input

[@ncjbennett]

Great job as usual. About all I know about wiring is not to stick my tongue on the battery terminals and your videos are so clearly communicated and demonstrated even I can understand what I’m watching. You really have a gift! You should design some amazing piece of electronic wizardry everyone needs and make a fortune.

[@280zone]

I applaud you for attempting this as wiring always seems to scare a lot of people. Probably for good reason:) A couple of hopefully helpful insights: You first mention you were going to switch the relays with the negative wire inside the cab. This is a great idea but you eventually ran the hot wires to the switch to relay connection. I would suggest switching to heat shrink insulated crimp on connections or adding heat shrink (with the glue) over the connectors. Heat shrink and wire loom is your friend in protecting wiring. Especially in your type of offroad rugged conditions. Your interior switch ground, needs to have the paint sanded off, add dielectric grease and a star washer to maintain a good ground. Hope this helps, not trying to be critical, just passing along information I have learned after several trouble shooting efforts.

[@vegajrg6]

I love your attention to detail on all your projects.

[@farillagarilla7999]

Just saw this video on my timeline. Great work... Interesting ideas too! For the long lengths of wire to be run you can secure them with a vice or helper and run the other ends in your drill. Then just wind them up together in a braid to keep installation easier. My $0.02... ✌

[@greggtakeuchi72]

I enjoy your videos. This my first comment EVER. Your attention to detail and safety make me feel like you’ll read and consider so I thought it would be worth my time. Of all the videos I’ve watched about adding a fuse panel with a circuit breaker, NO ONE thinks to protect the terminals of the circuit breaker under the support bracket. These (exposed) terminals are so close to ground sources (such as the bracket they’re mounted to) that they are a danger while working with tools nearby. Unless there’s an inline fuse, the line side (battery to circuit breaker) and (with the switch closed) the load side are unprotected. A short to ground would be scary, not to mention may damage the battery. I used Fastronix 5/16 - 1/4” stud terminal caps to cover the CB terminals under the bracket. I got these from Amazon. They’re about 2 for 7 bucks. Good value for the protection they provide. I suggest that you install these when you change to 4 gauge wire (of even if you don’’t). The risk may not be great, but is there. I hope this helps you and others. Best.

[@michealmorgan5564]

Wow, you have done an awesome job helping new Tacoma owners mod their ride. If you are not an engineer, then you should be. You approach your projects methodically and with some thought. I have done several mods because of you and have never needed to ask a question after watching your video. You definitely have the gift of teaching. I can't thank you enough for putting in the HOURS to make these videos. You're my Tacoma Subject Matter Expert (SME). Take care, Steve.

[@ChloeKuo]

This made my day and it means a lot Steve, thank you! I'm glad the videos are useful 😊

[@TWIRKNOLOVE]

Hi, for the concern you have with the mount-plate being close to your brake sensor: Get a piece of black rubber small diameter vacuum tube and slit it vertically. Cut to length and slip it on the edge of your concern so that there will be no hard rubbing.

[@JTerry-zl5un]

Thank you I don’t drive a truck but this tutorial was very well explained I wanted learn how to ad an accessory to a motor vehicle. I believe engineers a very good at explaining things.

[@dawabbitt3079]

This is awesome, because just yesterday I was in Harbor Freight (of all places) looking for affordable off-road LED lighting. They offered an auxiliary lighting kit for $26.99 - but I thought to do some research on the subject before actually buying anything. The 'kit' comes with one switch, one relay, one fuse and wiring needed to hook up *one* light bar. Seeing this video thumbnail as a suggested view in my KZbin browser first thing this morning (to me) was 'a sign'. Ha! I'll now be following *your* advice on building an auxiliary lighting *SYSTEM* instead, so - Thank you, for sharing this content! On a scale of 1-5, I give you 👊👊👊👊👊 for this content and you now have yet another new Subscriber!

[@joepaul1763]

You literally have the best Tacoma videos on your tube

[@miamitreasurehunter]

Wow. Thanks I just installed this today. I love my Bluesky Fuse box, breaker and frame. It looks Factory standard. I am getting the Stinger Jl Audio speaks in my 2022 Tacoma tomorrow and I needed this for the installation for my tech when he installs this. Thank you for your video to help me get this installed. You Rock. I am installing most of what you did for you Tacoma!! Next is interior lights and such. Thanks for sharing your experience!!! Kelly

[@androscharalambous7691]

Thank you for the Many Ideas of the parts and names you used in the Video, I have a project 4 Runner that Im getting Ideas for and you helped me out, keep the good work up....

[@DaveRogers583]

Excellent work. I'd get some wire loom and black electricians tape and just cover the wires where you're concerned about rubbing issues.

[@RadioReprised]

You have really improved and are killing it with your presentation! I have watched them all and think you deserve to know what a good job you do!

[@user-wj9hj7sf9y]

Hi Chloe, Love your Chanel, your videos have helped me with a lot of mods I have done on my 4Runner that are similar. It’s great you did this video… I am actually working on swapping out my wireless remote controller… it’s a love-hate relationship… it works we’ll but it’s finicky to say the least… I have installed a few accessories (lights, light bars, hidden bumper winch and bumper lights similar to yours, on board air compressor etc.) and at first so many wires and messy… so I cleaned and organized everything but the wireless remote option, though sounded good at the time has been nothing short of frustrations… some times the single connects and sometimes you got to swing your arm around pushing the buttons looking for the right spot for the controller and remote signal to connect 😂… after several attempts to improve the certainty and reliability by relocating the controller to get better signal I decided to look for a better option… this video has given me a great idea to build my own and use switches instead of a remote switch. I am excited to get started on this project! Thanks Chloe and happy off roading! 😊 Btw… if it were me I would cut the part of the tray you are worried about being to close to the break sensor wire… the integrity of the mount vs the risk to your breaking system… safety first, right… plus the risk of messing the Taco’s primary electrical by the aftermarket accessory cutting into it is a lot more costly and damaging then the cost of replacing the mounting tray should cutting compromise the mount support integrity… but I believe the mount has plenty of integrity and support from other mounting points and the components mounted on the tray are light… but you can see the set up you have and evaluate it more clearly then what can be seen in the video so do what you think works best and is the safest 😊

[@michaelm6624]

Chloe- I might suggest putting non-conductive trim edge pieces on any sharp edges. That way it's protected should they become damaged. otherwise it's a good & clean install !! Good Job !!

[@DeuceDeuceBravo]

I used Wire Barn for my wiring projects. Automotive grade wiring and all the connectors, loom, etc you could need.

[@Mumfy64]

This was my initial setup but knowing how much I was going to add to my Tacoma, I went with a switch controller. I knew that for everything I have planned to add, I didn't want to have a ton of relays. Great options for accessory hook ups.

[@MakersMike]

So for this set up you need a relay for each accessory? Switch controller you don’t?

[@Mumfy64]

@@MakersMike yes you would need to add a relay for each accessory. A controller like SwitchPros, AuxBeam, or the Garmin won’t.

[@MakersMike]

@@Mumfy64 thanks for reply. I figured. Just wanted to make sure.

[@jamesfreda1903]

You could put a piece of soft gasket material on the bottom of your panel to protect the wire where it's too close. Beats cutting it out. I happened to have some industrial grade adhesive backed soft gasket that I used in my boat to prevent vibration while towing .

[@DieselsHOGVlog]

Great video! As a power engineer and HD mechanic I'd love to see you re-do those big gauge wires to supply and gnd to copper solder ons, and your spades to shrink style with the addition of a little grease. I'd also never use butt connections but rather solder and shrink tube...its simply the only way to fly if you want any kind of longevity and safety! Keep up the good work! Version 2.0 would be a great time to re-do those connections. Cheers! ✌️

[@supuman]

Came to say this as well, cold soldered in an ORV is asking for it down the road. If you must crimp make sure to use a ratcheting crimper like Astro tools.

[@TheKingDorito]

dude i really appreciate all of your tutorials. have already done multiple since getting my TRD Off Road last month. I dont have human kids to spend on so this is my child lol

[@myvids4329]

Neat. I did something like this with my first Tacoma but this is much more elegant and I may need to do it to my new one.

[@vpolarbear]

Hya Chloe, My Wife & I Want to tell you that Your Incredible! We Have a 2021 Tacoma So You Have Been Super Helpful! Wow Your just Simply So Smart! love to see the Diagrams You Make. They are Amazing! Wish I Thought like that! I'm 60 & Wish I had the Energy & Brains you have. LOL. What a Beautiful Job you Have Done with your Tacoma! Have a Great Day & Thanks for all the Help Young Lady! it's Truly Appreciated!

[@danielsoroken9596]

Thanks for the heads up on Overland Equipped. Just went over and bout a fuse mount kit for my 2023 Pro.

[@jimhinkle5720]

Take some small fuel line and slice it to cover the edges and use RTV to hold it on, this will keep the ends from rubbing metal and being sharp.

[@Nackss]

This was the first mod I did! Amazing set up! I also like how you mounted the relays.

[@scotthughes5950]

Always very informative and detail oriented. Thank you. I like the idea for the relay placement. Been struggling with that for a while now. Awesome work. Thanks.

[@Sam-gb2hq]

Great video Chloe, you might look into the plastic edging that us electricians use for those sharp edges.

[@larryclappjr1414]

I think to protect the brake sensor that the mount comes close too. Is to go down to the 6 circuit panel that you were thinking about. Then make the clearance you need around the sensor your comfortable with. If you plan to stay with the 12 circuit. Then mark the area near the sensor and maybe bend the mount in that area down or upward to give you more clearance. If you can bend the mount carefully in that area. It could strengthen the mount.

[@tedspirakis4321]

This is part of my plan to custom install in my 2020 Tacoma, as well. Thanks for the great video, and the suggested parts information!

[@thomasoverton7131]

Excellent video. Nice clean install. Thanks for sharing 👍

[@dudefromkeene]

You can get thicker wire from welding supply shops, they also have more strands and are able to carry more amps

[@buttharvia]

Chloe, you rock! I really enjoy watching your videos and duplicating some of them to my 2008 Taco! Keep the videos coming!

[@diehlcorp7319]

You could wrap the corner by the wire in self sealing silicone F4 tape so the metal edge is covered in rubber. It should eliminate the possibility of the wire getting abraided. The Airforce uses F4 tale on aviation electronics for similar purposes.

[@Me-bf8bz]

You could always bend the corner up. Before making version 2 you might want to take a look at the DIY sPOD build. The diy Relay / fuse Panel is able to be made waterproof.

[@JamesBlack.177]

Always good to go with an oversize fuse block, you will be surprised how many accessories you can add. Using the relay for the lights is overkill, it is rated for 40 amps on a circuit that will definitely draw less than 10 amps. Assuming your switch can handle more than 10 amps, wire the lights directly to the switch and save the relay for a larger load circuit. Most aftermarket Carling style switches can handle upto 20 amps.

[@JamesBlack.177]

Nice work!

[@Mikp-zw3cs]

If you have the room at that corner and have a mounting area under it you might be able to use a post mount and bolt it on the corner and that will give you a sturdy corner. If that does not work you might be able to put a flexible rub rail on the corner just incase it does hit it will keep the metal from cutting the wires.

[@DarthPat1977]

Maybe some large shrink tubing for the harness your worried about for extra wire protection. One suggestion for your terminal connections though. Be sure to use flat washer underneath and on top of the lug. Also consider using lock washers under the nuts or maybe nylon locking nuts. This will prevent lose connections due to vibration.

[@bradd145]

Pro tip, try to use OFC copper.... oxygen free copper, it's more flexible, slightly smaller in diameter, and alot more resistance to corrosion.

[@jar145022]

Suggestion make a fuse box diagram listing the fuse numbers with what they control for a just like the factory function. Helps later on also when you forget what fuse is for what. Excel sheet and a laminator for a bit cleaner look. Could tape it to the inside of the lid possibly.

[@augtrailrider]

You could trim that corner and rivet in additional support if you think it looks too flimsy. Nice install.

[@thetinkercook5430]

Great vid and thinking, Chloe! Using this system for my trailer DC-DC charger. FYI: I used your LED light upgrade, and the lights for the license plate got wet and started to flicker. You need to have lights with a waterproof cover. Pax tecum

[@keifla12]

About that little piece next to the brake sensor you should take a small piece of rubber hose that would fit into that slot on the mount

[@5280Recreation]

Thank you for finding Grid Outfitters for me. I have a switch pro I’m installing and I just wasn’t happy with the cheap 3d prints and other options were meh or out of stock!

[@michaelmcclay357]

Awesome job! Both the video and the truck!

[@stevenreynolds5978]

You could always get a flexible gasket for the piece near your brake wire so you don't have to cut anything and you don't have to worry about it.

[@chopperskier]

PHENOMENAL INFORMATION! Great work! Bravo!

[@SpencerHogg]

Nicely done on the install dude, this looks awesome!!

[@Jakeaac]

outstanding project and well organized you are the Bom Ginisis’s

[@brucesatow]

Just an idea, but maybe add some lock washers next to the nuts on the bottom of the bracket? This would help the nuts from coming loose from vibration. A dab of blue (removable) locktite is also an alternative, as well as aircraft style lock nuts.

[@mattlewandowski73]

To protect your brake sensor wire further, you might consider getting a PETG or shrink wrap sleeve and cover the wire. Alternatively a bead of silicone along the bracket should give you the protection you are looking for. Honestly, make yourself a note to check it after your next couple wheeling trips... if there is ANY sign of abrasion, look for a serious solution (overkill is always acceptable) if not you are likely fine... just add it to an inspection checklist to do periodically. (you SHOULD have an inspection check list)

[@TheHanshotfirst]

Always an inspiration, thanks Chloe!

[@markw96789]

Beautiful job Chloe

[@MeToo9065]

Chloe, your the bomb! Thanks for, again, a great DIY vid.

[@jameswatkins7166]

Very cool project. Thanks for posting.

[@soccertl]

What about putting a plastic or rubber guard that slides over the edge to protect the wires?

[@fishtacoma]

Yeah like a grommet, kind of, in order to protect from fraying and chafing

[@richardtrammell7521]

Thanks for the info Sis 😊

[@trschreck]

perhaps you could add some verticle slots to the fender mount with a dremel so you can get another .125 in or so clearance ?

[@coblaze1]

Loved the video! Need more!

[@FRMN8R_T4R]

Love this! Man, I wish Guild Outfitters (or someone else) would make custom panels like that for the 5th gen 4Runners. I'd love to have a more OEM look than the aftermarket Switch-Pro type touch panels mounted randomly on the dash somewhere

[@alexs825]

The 2020+ Tacoma have as many switches as she shows here so maybe check to see if Toyota sells newer switch panels for later models

[@jlrecoder1]

Great Video! I have a question, can you just make it and install it on my Taco? 🤣 Good job Chloe, this mod is on my list.

[@shawnpylant6568]

amazon sells a product called edge guard which is a push on edge guard for electrical safe.

[@jank1464]

May I take you out for a motorcycle ride? 😏 love your channel and truck!

[@RTX-mz3rg]

Just got my trd sport 🥳

[@fj40pinobilt]

Hello Chloe, I am wiring up some reverse lights on my Taco with the same switch that you are using. Thanks for posting it is really helping with my install. The wiring diagram you provided is awesome. I have one question for you: Did you NOT use the "Red 2" wire from the push switch connector, at all? I thought that was supposed to used to allow the push switch light to be turned on with the tail lights?

[@davidr.1517]

I was getting ready to ask the same things. I'll ask in a new question and hopefully she can get back to us.😊

[@davidr.1517]

Hi Chloe, great video's and thanks for all of the details. When you hooked up your switch to the fuse box inside the cab, ( with the add a fuse ) does that connection back light up the switch like when the DRL's are in or when the headlights come on automatically?

[@vr6isfaster]

A lot of aftermarket LED lights, particularly the off-brands, draw way less than advertised. It's like the old days of "10,000W peak" amps on eBay, the lies must sell. I tested some NiLight pods off amazon for a project and found them to draw 12-13W, or about 1A at 12V.

[@stig120212]

So awesome!!

[@ever2gut1]

I did something similar to my truck with an amazon kit from 8gang which is pretty much an unbranded auxbeam. Curious as to how the relays were connected to turn on with the lights being on. Awesome that you have the option to use stock looking buttons!

[@bdyer6football]

Late comment but aluminum is a very weird surface too coat. That being said I'm not sure about bedliner, but as a powdercoater I can say powdercoating is one of the best ways too customize aluminum and we actually have painters bring us pieces too coat in primer and will paint over it

[@skg5067]

Great information

[@drewncars9505]

I’m sure I could just look it up but I wonder if there are brackets that are made for the manuals too. The location where you have your under hood wiring panel is where the clutch fluid reservoir is mounted

[@julianmora5473]

I have never seen a woman work on a truck in my entire life........ This was new and pretty entertaining

[@thomaszach0229]

Great video! I've been interested in something like this after getting my Tacoma. At what point would I want to consider adding 12v relays?

[@mattvohrer6049]

Did you ever add the inboard air compressor to this auxiliary unit? If so how?

[@jadzbrigoli3462]

nice video chloe 👍👍👍

[@SilverPhoenix-PlazmaMoon]

Is making sure the buttons make a *clicky* sound a thing? I mean, it was hella satisfying...

[@raymondabella4684]

Nice and informative vid.👍 I have that same 100A breaker switch and the 6 slot version of that fuse block. He had issue with me going with the 100A breaker and told me to go with the 40A version. Yet most people go with the 100A version with no prob. I'm mostly running lights on the block. Maybe 3 that will need relays and the other, lower leds like Raptor lights, led rock lights and led strips to illuminate the bed. I mainly just like to use the breaker as a main kill switch. Do guys think I should ditch the 100 for the 40 like he said or can I keep the 100A with no probs?

[@rickgrant5844]

Try heat shrink Or all weather rubber electrical tape

[@reyca9294]

The battery cable goes on the circuit breaker goes in the LOAD ?

[@justingazabat]

How do you size your wire so that you are feeding your fuse panel with the right gauge power lead? For instance, What if you want to run your fuse box 10 feet away from the battery? I'm trying to sort out how to measure everything correctly on a VW project I've got going, and the battery is under the rear seat, but the fuse block needs to be upfront under the front bonnet. Thanks!

[@Dave_Cooks2]

loo into a company that makes the Deutsch connector. its a much stronger connector and will not allow water to get inside the connector. The wire will break be for the connector does. thanks

[@vr6isfaster]

Blue Sea Systems is a great example of "you get what you pay for."

[@jtaco66]

Clean!

[@alexanderstein5379]

How did you get they switch on your dash to the left that says camera front and back ? And how did u wire it . And what front and rear camera do you have ?

[@benfrausto7699]

Does the fuse block have constant power? Or, only with igniton on?

[@vncentngyn]

Hey Chloe or anyone, what do you usually do with the parts you replace with aftermarket’s? For example I switched out my factory headlights for some aftermarket ones . Where can I sell them?

[@prorazzo334]

So is the amp necessary in this case? Can’t I just run the circuit breaker?

[@bngately5757]

What are the relays that you used

[@calebvautier5278]

I know this video is older, but I was wondering if anyone has done anything similar on a Chevy. A 2017 Silverado 1500 to be exact. I'm looking to do a bunch of lights on my new truck, and this is an amazing set up.

[@calebvautier5278]

Edit. As far as an engine bay mount.

[@ht1261]

Hi Chloe, do you have any economical solutions for catalytic converter theft for Tacos? Thanks for all your informative videos.

[@ChloeKuo]

I have a video coming next week of installing a Cat Shield! Shields are expensive but about 1/3 of the price of one new catalytic converter (and my Tacoma has 2).

[@raymathews7035]

What does it do!! I had LED's installed on my Camry XLE.

[@Dave_Cooks2]

I think it is to close to the break switch. I would trim it back a little. Need to do something like that for my cameras when i am storm chasing.

[@ericsugalsku1826]

How long did it take you to install all of this Chloe?

[@Sam-kn2mm]

Im new to wiring and dont have any real world ppl to ask questions to. Im currently installing fog lights on my 2022 SR, i bought the fuse block but do i have to use a Blue Sea 100A Circuit Breaker?

[@edzapiain413]

what program did you use to make your diagram

[@LeandroFTW]

Any issues with the canbus system?

[@keifla12]

You and I have two completely different ideas about IKEA. They have crappy furniture. They charge just as much as everybody else and you have to put it together for them.