Circle Burners Where To Get Them How To Use Them

[@45Mang]

That’s gorgeous smooth ass cut!!! That’s almost like a water jet cutter!!!

[@themaloneybrothers7063]

holy cow, gotta get me one of those, tired of walking around the material I'm cutting especially in a smaller shop setting

[@JacobSchofield]

If you take care of it, it will last forever

[@1nvisible1]

*[...Jacob showing his dad card...] "hey let's blow some Mickey Mouse ears on this thing!"8 *Also a clean cut that's going to save you 25 minutes of cleanup AFTER you have the rigtht file and flapper disk found.*

[@Biokemist-o3k]

holy heck!! That thing is mint!! Why have I never seen one of them before. I must run with a real cave man crowd.

[@bretbroome2118]

If your using the plug, start with your tip outside the cut, blow through, then without letting off of the high pressure, slide the point into the punch mark. Try to make it a smooth transition and just start your radius cut immediately after you drop in to the punch mark. What this does is make it where you don’t have a blow through hole in your part. If you’re using the hole, do the opposite. When you get used to it, you won’t even need to grind. Unless you’re going to weld on it.

[@terrycapehart6303]

Thanks have a blessed day America

[@randycortez5738]

Hi Brother. Is the adaptor removable?? Thanks

[@VantageWelding]

Do they make them for plasma setup? That would be sweet deal for my hypertherm

[@justinlongoria9306]

My exact thoughts

[@bbbiesemeyer1]

You can make 1 out of a piece of 1” flat bar drill a 1/4” hole then measure whatever the radius of a circle you want then drill a hole for the drag tip to fit in. Drill a 1/4” hole in the center of the circle you want and put a bolt . It works pretty good just have to weld the hole up when your done and it’s cheap

[@JacobSchofield]

They will be here shortly

[@davidcat1455]

Hypertherm makes them. They fit straight onto the torch. Edit; Because y’all have a drag tip you don’t need the outrigger wheel. You can still use the wheel if you want it’s just not necessary.

[@afandiindah2912]

is it sold online? Can I ask the name of the tool?

[@chadkennedy529]

That's a quality piece of tooling brother, gotta snatch me up one.

[@JacobSchofield]

I think you are going to love it

[@Laura-wc5xt]

was waiting for your tarp to flare up......great little video Jacob ...cheers

[@wadewittman8510]

Great review Jake 👍! Yeah some crazy weather, that's for sure.

[@JacobSchofield]

Thanks Wade. Hope you are doing well.

[@wadewittman8510]

@@JacobSchofield yeah not too bad. Stay safe out there buddy 👍

[@betrickey]

That sounds like some good ole Northern Missouri weather we get.

[@JacobSchofield]

Has it been crazy over there too? Not going to lie we thought the snow was over 😂

[@giannirocco7492]

We just made them ourselves,they're actually pretty simple!

[@lesliealvinstewart8414]

Good job jacob

[@edmilson3107]

3:53. Gostaria de saber o valor e se vcs importavam para o Brazil

[@beachboardfan9544]

Be curious to know how long that bearing lasts

[@derekdavis9468]

Thanks Jacob!! Definitely going to go check this out. We all appreciate all the videos you do!!! They a very educational and very informative. Be blessed sir!!

[@JacobSchofield]

Thank you Derek means the world us that you guys enjoy the videos. Be blessed

[@mohnjarti]

Jacob do you know the discount promo code for this?

[@jaysen2200]

Minty 👌. I really need to upgrade !

[@JacobSchofield]

This thing is worth up grading to

[@jaydenridnour195]

Exactly what I needed man, thank you

[@JacobSchofield]

Glad it helped Jayden.

[@matthewdavis3884]

Well, you made me buy one......

[@mursyidinroisnasution7905]

How do i get the tool

[@ColKorn1965]

I built my own circle cutter for the plasma cutter....I'm sure I could put a bushing in it and use it with oxy-acetylene

[@JacobSchofield]

Right on.

[@chrissisemore269]

How big does it go

[@Jay22222]

I didn’t quite understand how you adjust the radius of the cut. I can see how to raise and lower the torch up or down towards the steel using the wingnut. Or does it just come with a few different pre-set sizes of that L shaped attachment Like 1” 2” 4” or something like that? Stay blessed bro EDIT: Watched the B roll and first cut again. I see how to increase or decrease the arc now

[@JacobSchofield]

I’ll do another video. This kit will cut I believe a 5/8 to 16” hole

[@gregbetts8057]

hahaha , get you some devil dust lol . good to see you back great vid , thanks

[@JacobSchofield]

Thanks Greg felt good to finally put out another video.

[@paulgarcia458]

Were in a drought in Florida,

[@denniskalivoda]

This particular cutting device looks good but, I noticed that you didn’t show cutting a bigger radius, such as in the range of 8” to 12” in diameter. Little diameter like what you did there of about 5-6 dia is the maximum for this cutter device.

[@lesliealvinstewart8414]

Hows the pipeline work doing?

[@JacobSchofield]

I haven’t been on a pipeline since last April. 😂 we where kinda forced to find other means of work which in the end was a huge blessing to us.

[@bustersmith5569]

@@JacobSchofield you can thank Biden for that 👎💩

[@treeman765]

Thanks for the video on that circle rig! I’m gonna pick me one up. The link you put in the description doesn’t work though and I have to ask, are you growing one of those ridiculous mullets like I see every teenage boy have nowadays? Lol

[@scrappymocha]

Nice

[@jrad3966]

Straight torch on the small circle works better...... 90 degrees on a flange wizard for the bigger diameter holes

[@petermccuskey1832]

Sweet

[@IROCKID]

Where are you located?

[@JacobSchofield]

Western United States

[@gabewhisen3446]

Cool

[@robertqueberg4612]

Don’t force it. Get a bigger hammer. Your cuts look much like machine burned parts that I have had made. Good job!

[@DragonflyAcres2022]

Looks to me a global warming 😂 😂 😂 😂 thank you for sharing

[@MrMrjones333]

👍👍👍

[@deakeschneider5080]

Wish it was about a hundred dollars

[@snapponduran]

Get you local machinist to turn you out a bushing for that baby 👶 torch

[@JacobSchofield]

Cory great thoughts, I think circle B technology is going to build a lot for a baby torch and a plasma set up. Should be coming out here shortly.

[@jray7656]

Very nice but to rich for this guys blood.

[@JacobSchofield]

Good tools always cost money. But if taken care of this thing could be handed down.

[@TheRitchieLeeShow]

Worth every penny??? How many pennies did you pay? Wtf

[@JacobSchofield]

Lots of pennies.