CNC MILL BUILD PART 30 - MACH3 USB CONTROLLER LIMIT SWITCHES SERIAL WIRING FOR Z AXIS

Other videos:
part 29 - • CNC BUILD PART 29 - WI... - MACH3 USB BOB + CNC V3 SHIELD + TMC2209 DRIVER FOR Z AXIS
PART 28 - • CNC BUILD PART 28 - SM... - SMC 01 STEPPER MOTOR CONTROLLER
PART 27 - • CNC BUILD PART 27 - CN... - CNC MACH3 BOB SOFTWARE AND DRIVER INSTALLATION
PART 26 - • CNC BUILD PART 26 - TM... - TMC 2209 DRIVER - MOTOR CURRENT SETING WITH Vref PIN VOLTAGE
PART 25 - • 3018 CNC BUILD PART 25... - X AXIS SCREW AND MOTOR MOUNT
PART 24 - • 3018 CNC BUILD PART 24... - NEMA 23 STEPPER MOTOR SUPPORT BLENDER PROJECT
PART 23 - • CNC BUILD PART 23 - TM... - TMC 2130 DRIVER - MOTOR CURRENT SETING WITH Vref PIN VOLTAGE
PART 22 - • 3018 CNC BUILD PART 22... - ER11 SPINDLE MOUNT
PART 21 - • 3018 CNC BUILD PART 21... - ER11 CHUCK SPINDLE MOTOR SHAFT EXTENSION - UNBOXING
PART 20 - • 3018 CNC BUILD PART 20... - Z AXIS TOUCH PROBE UNBOXING
PART 19 - • 3018 CNC BUILD PART 19... - CF5135B-Z TACHOMETER UNBOXING
PART 18 - • 3018 CNC BUILD PART 18... - MACH3 BOB UNBOXING
PART 17 - • 3018 CNC BUILD PART 17... - TMC 2209 DRIVERS UNBOXING
PART 16 - • 3018 CNC BUILD PART 16...
PART 15 - • 3018 CNC BUILD PART 15...
PART 14 - • 3018 CNC BUILD PART 14...
PART 13 - • 3018 CNC BUILD PART 13...
PART 12 - • 3018 CNC BUILD PART 15...
PART 11 - • 3018 CNC BUILD PART 10...
PART 10 - • 3018 CNC BUILD PART 11...
PART 9 - • 3018 CNC BUILD PART 9 ...
PART 8 - • 3018 CNC BUILD PART 8 ...
PART 7 - • 3018 CNC BUILD PART 7 ...
PART 6 - • 3018 CNC BUILD PART 6 ...
PART 5 - • 3018 CNC BUILD PART 5 ...
PART 4 - • 3018 CNC BUILD PART 4 ...
PART 3 - • 3018 CNC BUILD PART 3 ...
PART 2 - • 3018 CNC BUILD PART 2 ...
PART 1 - • 3018 CNC BUILD PART 1 ...

[@Stoneforth]

My board was slightly different. I wired everything the same except DID NOT connect anything to the DCM terminal. Doing so caused a short where limit switches would activate output pins. I just connecting what would normally go into DCM terminal to negative on the power supply.

[@dorinionescu8305]

Multumesc de informatie!

[@CNCEVOLUTION]

Ce masinarie a-ti construit? 🤔

[@Abd488BPH]

Спасибо тебе огромное Добрый человек.

[@ЕвгенийЛеонтьев-р6э]

именно 24 вольта нужно подключать или можно меньше?

[@CNCEVOLUTION]

в характеристиках платы написано, что она сделана на 24 вольта

[@riezki5224]

if use peoximity sensor is same wiring ??

[@CNCEVOLUTION]

no

[@ihzanursyahbana7773]

if you guys think this is actually work, no its not. but as an exchange you can use active low pararel switch by put 1k resistor between 5v and IN1, than use this schematic for IN1 and ground Edited: i just realized if the mach 3 optocoupler power source was from 24 v, so yeah, its already being pararel at the first place by using IN1,IN2, and so on as a ground for switching (HIGH and LOW) the optocoupler

[@53fps55]

Scam? Saklar Tidak memakai rangkaian paralel adalah pembodohan

[@CNCEVOLUTION]

sinyal selalu diaktifkan dan ketika terputus, pengontrol mengetahui bahwa salah satu pembatas telah diaktifkan, jika Anda menghubungkan pembatas secara paralel ketika salah satunya diaktifkan, sinyal tidak akan terputus dan akan terus melewati pembatas lain, sehingga pengontrol tidak akan pernah tahu bahwa salah satu pembatas telah digerakkan

[@53fps55]

@@CNCEVOLUTION Apakah anda menggunakan jenis saklar jenis NC?

[@CNCEVOLUTION]

@@53fps55 kzbin.info/www/bejne/gaLbnJlmlp54fK8

[@CNCEVOLUTION]

@@53fps55 sakelar biasanya tertutup dan biasanya terbuka tergantung pada apa yang ingin Anda pilih