Commercial Faucet Install Kits

Рет қаралды 35,124

Күн бұрын

Пікірлер: 28

@TheMusicScaleMan 6 жыл бұрын

Outstanding explanation! You're the first person I've seen on KZbin that makes this easy to understand and visual shows how to do this step by step. Thanks bro!

@atshelp 6 жыл бұрын

Robert Johnson, thank you very much! Comments like this make it all worth doing. -Tim

@marysmith4811 5 жыл бұрын

OMG!!! Thank you!!! I am interested in purchasing one of these sinks for my basement laundry area and I wasn't sure if the pipes needed to be jutting out of the wall, or if I could use hoses! You are the only one who explained this so well.

@zipzippery Жыл бұрын

good job Tim - no faffing around - straight to business!

@007vsMagua 5 жыл бұрын

I've been having problems mounting the faucet to my sink that came as a combo from Amazon. The setup your demonstrating is the same setup I'm using. Yesterday I probably spent an hour standing if front of all the parts on display at Menards. I left scratching my head and when I got home I found this video and thanks. I just ordered an EZ-Kit and it's on the way. I stopped by our First Supply in S.E. Minnesota this morning and they had no solution.

@atshelp 5 жыл бұрын

Sorry you were having issues. I’m glad this helped. We just make videos whenever we get a question we get often. I’m glad we’ve been able to help solve issues.

@thesilverlearningchannel6560 2 жыл бұрын

best video on this subject, thank you!

@atshelp 2 жыл бұрын

Thank you! 🙏🏻🙏🏻🙏🏻

@ngodline12 5 жыл бұрын

What do you do if it leaks between the eccentric adaptor and the brass nipple?

@manstersr 3 жыл бұрын

I'm installing in my garage an American Standard 8350235.002 Faucet into an old style cast iron porcelain/enamel commercial deep sump sink that sat in my back yard for about 30 yrs. (not too rusty either). The video helps as I had purchased with the faucet a T&S B-0230K nipple kit or as they call it installation kit. I'm glad you answered someone else's question about putting pipe tape on the nipple part going to the faucet but with this kit I threaded the nipple into the block part and it doesn't seem to tighten before it bottoms out. I plan to put about 8-10 wraps of tape on it or whatever it needs to make it tighter. I was wondering about the slight offset of the faucet inlet, is that for slight variations in the hole centering of different sinks and/or for leveling wall mountings?

@atshelp 3 жыл бұрын

That is weird that is bottoming out without tightening. There is supposed to be a slight taper to the thread. But thread tape should help. As far as the offset, yes it is just in case the faucet holes are slightly off. A lot of builders will punch holes in their stainless on site.

@bokebowl7460 6 жыл бұрын

thanks man! got my commercial sink set!

@atshelp 6 жыл бұрын

Patrick Fleming,Fantastic!!Cool hidden feature, the nipples have a hex key pattern on the inside. If you don’t have an Allen wrench big enough, you can use a large screwdriver to get it nice and tight in the fixture.

@marklarson2299 3 жыл бұрын

My question is to the Ats guy my kit has the large black washer. You did not use that in your video with the backsplash mounted faucet if I use it which side does it go on the side where the faucet is or the backside behind that Jagged washer

@atshelp 3 жыл бұрын

Black rubber washer on the backside of the sink before the jagged washer. This helps lock it in place and prevents slippage. 😉

@erikbender1 3 жыл бұрын

my half inch nipple leaks. I am using teflon tape and pipe dope . how do you get it water tight ?.

@atshelp 3 жыл бұрын

erik Bender lots of tape will usually do the trick. Only other tip I can give is the nipples have the hex on the inside if you can get a screwdriver big enough to fit in the groove to get it really tight. If all else fails, pipe dope. But I’d just layer up on the tape to be honest.