Head Gasket 0:15 Head and Head Bolts (x8) 0:22 Cam and Cam Chain 0:35 Cam Sprocket 0:58 Cam Chain Tensioner 1:09 Tensioner Shaft 1:32 Head Cover Gasket 1:43 Head Cover 1:48 Head Cover Bolts (x11) 1:57 Right Crankcase Cover Gasket 2:10 Right Crankcase Cover 2:15 Right Crankcase Cover Bolts (x11) 2:26 Check Valve Clearances 2:52
@XRLand6 жыл бұрын
Thank you, sir!
@marlioavilespatino29462 жыл бұрын
Una belleza de motorrrrrr. Lo maximoooo
@oswaldog8311 жыл бұрын
Con estos video hasta ganas de desarmar mi moto me dieron....Salu
@bardinkurtis3 жыл бұрын
Does cam shaft lobes need to be down at TDC? I had it at the T with marks lined up on cam shaft sprocket but cam shaft lobes were up. Manual doesn't mention anything about cam shaft.
@DahTrueMac9 жыл бұрын
When aligning the camshaft at top dead center, are the cam lobes facing up or down?
@Psykam5 жыл бұрын
Hey @XRLand , where does the little timing mark on the kickstart shaft cam next to the right side crank case cover line up with? I have an 83 XR500R that I just took the right side crank case off to replace the gasket, and couldnt find the corresponding mark, and now my kickstart lever doesnt retract back up on its own. I didnt even take the clutch basket off.
@elmaestrodelvicecity4 жыл бұрын
How do you prevent oil leaks from the mating surfaces? I always clean really well and use oem gaskets but sooner o later i always end up with leaks
@themadsmith8575 жыл бұрын
I'm rebuilding my xr600r. I wasn't paying attention and my cam rolled off the table, I don't see any damage do you think it's safe to use?
@XRLand5 жыл бұрын
Probably safe to use if you don't see any damage. But I'm no metal expert. Sorry to hear about that.
@sciencemilitia18536 жыл бұрын
0:59 it looks like you have the wrong side of the bearing pointing outward. The sealed side goes on the outside, I believe. Correct me if thats not it
@XRLand6 жыл бұрын
Yeah. The bearing was backward. I purchased the bike used, and this is how it was when I found it. Good observation.
@KFLY679 жыл бұрын
Hello I been getting mixed information so what is the torque on the main cylinder bolts and then the head bolts? in foot lbs? I have a xl600r
@KFLY678 жыл бұрын
Ok thanks ,explains why almost all the bolt threads were severly stripped and needed re-tapped and heli-coiled.
@gabin5545 жыл бұрын
When you do the valves... And you have the engine on T mark you put it on The "T" ? Or the "l"that Is on the left of "T"?
@XRLand5 жыл бұрын
Hey gabin554, you should have it on the T (top dead center). Make sure the rockers are loose when measuring so you know you're at the correct TDC.
@gabin5545 жыл бұрын
@@XRLand Okey thank you very much!
@XRLand5 жыл бұрын
You're welcome!
@cesarnavarro76148 жыл бұрын
muy buen video. que medida para la admisión y que medida para la de escape?
@dimasikyeti4 жыл бұрын
Зачем пропускаешь самые важные нюансы? например про шпенек под распредвалом.
@MalcolmB8910 жыл бұрын
i have a xr500 and have to remove head is it the same cam chain tensioner set up as this its a 83 model
@stmboat5 жыл бұрын
1:05 interesting you dont use the honda cct tool. I'll double back to see how you uninstalled it but I don't even know how its possible to assemble/disassemble without it.
@shanenouri5 жыл бұрын
Steamboat it uninstalled easily. Installation using the zip tie was a pain, but doable.
@Nasoukikos12 жыл бұрын
my xr had a broken cam chain tensioner, i don't know how it happened but there was an awful noise coming from it and i was loosing speed, and one time the bike turned off while i was going uphill
@Dado339 жыл бұрын
you left seals on cam shaft bearings? Why?
@XRLand9 жыл бұрын
You are right! They should have been replaced. Good addition, thank you!
@-calamities-37448 жыл бұрын
hello exhaust valves of how many millimeters leave ?