Bad Boy Maverick - How to change mowing blades - PROBLEMS YOU MIGHT FACE

[@deanlewis1650]

I totally understand the frustration of breaking those bolts. I used to have that problem too. Then I started using anti seize on them. Works great

[@JustinsProject]

I will have to try that on my next swap. Thanks for the tip, much appreciated 🙏 Thanks for watching and commenting! 👍

[@larry7868]

The fact that you showed the bolts were so tight that a 30 minute job became 2 hours makes your video a favorite. That is my world and I have come to expect it. Time for job times 3 is the real time. Thanks, your video is informative, relevant and real!

[@larry7868]

Also, My oil plug is about the same tightness as the blades. Whoever put the bolts in was a BadBoy for sure!

[@JustinsProject]

Much appreciated 🙏... 100% 🤣 All projects take much longer than expected. I'll be changing the Hydro-Gear fluids soon. I REALLY hope it goes smoother than the blades lol

[@JustinsProject]

@@larry7868 Yeah, they have Thor and Brian Shaw in there tightening bolts 🤣 Thanks for watching and commenting 👍🏻

[@larry7868]

@@JustinsProject I’m behind you by 6 months. So you make the mistakes, figure it out for both of us and I’ll watch the videos. Lol Best of Luck my friend

[@JustinsProject]

Sounds like a good plan 😁

[@jodycornelison7653]

I personally like using anti seize on the bolts and use a paddle wheel instead of a grinding stone or file. The paddle wheel doesn't dis-color the blade which can take the temper of the blade making it soft. I did enjoy the video. Thanks for sharing.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@SilverFireStoves]

Recently changed blades on this exact model Bad Boy mower, despite using a 4' breaker bar (lots of leverage) and the socket split in half. This 15-minute job took hours (due to seized bolts, as in your video). I had to heat bolts (Mapp gas) and tap the socket with a copper hammer to release them. Bad Boy obviously put on with impact wrench and over-tightened the bolts. I'd highly recommend adding anti-seize lubricant before reinstalling bolts so next change things go smoother and retorque bolts to recommended 90 - 100 pounds. I would not use an impact wrench. They will flatten the Belleview washers that are supposed to remain in their concave and convex shape, not be flattened and distorted by an impact wrench. Another option when releasing blades is to put a flat wrench on the shaft directly above the blade for a secure shaft hold. That's why the shaft has the wrench notch for a secure hold. Beating unheated bolts with a sledgehammer may shear even grade 8 bolts.

[@JustinsProject]

Lots of good info. 👍🏻 Thanks for watching and commenting 👍🏻

[@mrme9517]

MILWAKEE M18 FUEL 1/2" IMPACT ZIP IT LIKE ITS NOTHING OR BREAK THE BOLT OFF EITHER WAY NO STRUGGLE LBVS

[@lorenpinger3925]

I got my 2022 Maverick HD last year with the Honda EFI 779cc / 54in. It's great. I lift it like you did to powerwash under the deck and use my cordless impact to remove the blades to sharpen them the same way. Thank you for your video !

[@JustinsProject]

Awesome stuff! Great mower! Especially the HD. Thanks for watching and commenting 👍🏻

[@user-cf3rf6ey6f]

Mojack lawnmower jack and impact wrench works great for changing blades

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@JT-dx1qk]

Only use a 6 point socket on a bolt that tight. 12 point sockets are only good for 12 point bolt heads - Twice the grip with 6 point. Impact gun and impact socket is a must

[@JustinsProject]

Yeah that's true, but I used what I had at that time. 😁 Thanks for watching and commenting 👍🏻

[@jimhodge8594]

At least use the boxed end side of the wrench, not the open side. Your losing turning force and it's a wonder it didn't fly off and put your eye out.

[@superpanda978]

This is exactly the video I was looking for! Your videos are very entertaining and informative! Keep up the hard work brother!

[@JustinsProject]

Much appreciated 🙏 Thanks for watching and commenting 👍🏻

[@zaineridling]

Despite how many tools it took, you were right! Really liking what Bad Boy is doing in the commercial market; like Wright mowers, their philosophy of fewest/best components wins the day. Thanks for filming the struggle. Made it interesting. I got pissy when I saw an oil change video where the oil filter was tucked in a tight space with poor drainage, and the guy had loosened everything before filming. What a killjoy! 😅

[@JustinsProject]

In a perfect world, everything would loosen just fine. Even with an impact these bolts give me a problem every time I change the blades. I gotta start using the anti seize to see if that helps.

[@TheN1GatorNation]

Ran into same issue. Good impact gun, takes bolt off like butter. I use it to put them on as well, get bolt tight, let it compound roughly 3 times, and it’s good…people would say I’ll strip or over torque. 6 years later, bolts still look new. Never had an issue.

[@JustinsProject]

Good stuff. Thanks for watching and commenting 👍🏻

[@gkcamden9050]

I like your test because it reminds me of something I already knew, but wasn’t considering while I watched you lift the mower; the deck is independent of the rest of the mower. Your jackstands held the deck up, while the rest of the mower fell. 👍🏼 Edit: Ok, I watched the rest of the video. Thank you. Your video showing the challenges of getting those frigging blades off has saved me a few hours.

[@JustinsProject]

I am glad you found it helpful. Thanks for watching and commenting 👍🏻

[@tiptoesparadise7517]

Thanks. I thought we were going the wrong direction. Very helpful.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@mikesbarn1858]

First time working my blade I had to disassemble the spindles and use a lot of heat. I have the same problem when cutting tall grass. Check your RPMs. Mine was 2700 max. I adjusted the governor to 3500. I also had to go one jet size larger. Consider pipe wrapping the muffler. Lowers engine compartment temperature up to 100 degrees

[@JustinsProject]

Thanks for the tips. Appreciate you sharing that 👍🏻

[@greglewis8752]

I learned a long time ago not to push a wrench to tighten it. I think the words spoken to me was that you 'cannot push a chain'--same for a wrench. Also, always use a box end of a wrench when loosening/tightening a bolt.

[@JustinsProject]

Thanks for the tips. Much appreciated 🙏 Thanks for watching and commenting 👍🏻

[@ScottyLo]

I have to admit you had me laughing when the 2nd blade was just as tight as the first one. Ballard makes a great lift for zero turn mowers that raises the deck and holds it safely and it gives you plenty of room to use an impact drill to remove the blades. I don’t recommend using it to reinstall them because I sheered my spindle off with it. Hope it helps

[@JustinsProject]

🤣 That middle bolt was total @$#!% ... lol I'm glad to have my new blades though. I'll look into that lift. Thanks for watching and commenting 👍🏻

[@rickforsty9410]

Use anti seize on the threads. When you hit things with the blades they tighten. Impact and anti seize is the way to go!!

[@Outsidewithgary]

Great video. I am buying a maverick and this was very helpful.

[@kevins4611]

​@@JustinsProjectIt hurt me to watch you do it the hard way. I was going to encourage a lift also. It takes up a small amount of room in your garage. But well worth the money in the long run. You can use the impact to tighten, just lower the torque if you are worried about sheering a bolt. While I was working with a landscaping company for years, they just told me to watch the socket and stop when the socket did. Never had a problem. I've tried tightening with a socket before and lost a blade while mowing. Luckily everything was laying within 2 feet of each other. Keep up the videos brother. I'll have to check out your videos on Solar. I've been wanting to go solar myself, but the cost increase for home insurance just doesn't make sense. So hopefully you've addressed that. Thanks!

[@mrme9517]

I HAVE A 22 MAVERICK HD WITH THE 27 HP EFI HONDA IT LEAVES GRASS AS WELL DIFFERENT BLADES ETC AND SEEN COMMON ISSUES ARE SPINDLES OR PULLEYS BUT I'M VERY DISAPPOINTED IN THIS MACHINE BUT APPRECIATE THE CONTENT AND MINE STILL LEAVES GRASS WITH NEW BLADES

[@JustinsProject]

Thank you for sharing your experience. 👍🏻

[@lorenpinger3925]

After 21 hrs on mine. My only issue is the dull blades on weeds.

[@JustinsProject]

@lorenpinger3925 200 hrs on mine now. That kohler is still kickin' strong. I mow 6.5 acres weekly. I've mowed 6 ft weeds and regular grass. Hell, I even bushhogged with it lol No mechanical issues whatsoever.

[@brennan5220]

Cordless Impact makes thing so much easier!!

[@JustinsProject]

So true 😁 Thanks for watching and commenting 👍🏻

[@toddzimmerman8041]

same issues, purchased a 3/8 bauer impact from harbor freight for cheap(300 ft.lbs) , has saved me a ton of headaches

[@JustinsProject]

Good tip! Thanks for watching and commenting 👍🏻

[@DT-mm6do]

Appreciate your humanity.

[@JustinsProject]

😁 Thanks for watching and commenting 👍🏻

[@glentaylor3013]

Bud you need electric Impact & a blade balancer tool or you will be going thru Mandrels like crazy

[@JustinsProject]

@@glentaylor3013 I have the electric impact but no blade balancer. We will see how it holds up.

[@bigjimflying7195]

1. Why didn’t you lift the front of the mower up another 6-8” and use an impact to start with? 2. Why are you using the open end of your combination wrench instead of the box end? 3. Slow down some while mowing and you’ll get a better cut. Just saying. I got a BB Rogue 61” w/ the Kaw 1000FX this week! Sure beats my Husqvarna Z246. LOL

[@JustinsProject]

It invovled getting more tools from my building #2 which was not readily available at the time. Plus a lot of videos show it to be very simple so it wasn't supposed to be so difficult. The speed of the cut was for demonstration proposes not how I always cut. 😁 Thanks for watching and commenting 👍🏻

[@keith6872]

Angle grinder and 36 grit flap disc works great for quick sharpening.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@BrianGemberling]

Thank you, this video was very helpful for me to understand the capabilites of the mower. I appreciate the review and you have helped me make my choice for the 4-5 acres we need to maintain

[@JustinsProject]

Glad it was helpful! I made another video on mowing our backfield when the weeds out there got extremely high. You might like that one if you haven't already found it. Here is a link to that kzbin.info/www/bejne/aIXddp2pdsmggrM - Thanks for watching and commenting! 👍

[@robbiewharton2117]

Thank you so much I don't watch 2 or 3 videos and they just take the bolt out and I'm sitting over here with a cheater barn. Using my legs and pushing on it and I can't get it right loosen. I'm saying it down everybody else didn't easy.

[@JustinsProject]

I know, right? Thanks for watching and commenting 👍🏻

[@nickikarr2613]

I use my DeWalt setting on two to take my blades off works pretty good. You can order a lift from Ballard products somebody else that makes one that I bought mine from but I can't remember who it was hooked to the bottom of your deck lifts it up all you have to do is reach under makes it real simple and easy might check that out. It's definitely a Time safe.

[@JustinsProject]

Awesome! Thanks for watching and commenting 👍🏻

[@patronsaint476]

Floor jack to lift, jack stand to support, impact gun to loosen and torque wrench to tighten. These are the tools you should be using for safety, efficiency and effectiveness.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@sheilaashley]

Awesome! Now, I no longer need to clean up the stragglers!! Yehhh!

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@ericf.7081]

The tightness of the books is exactly why i bought Mower lift and use my 1/2" 20v impact

[@JustinsProject]

Thanks for watching and commenting

[@lorenpinger3925]

Cordless impact makes the job super easy

[@JustinsProject]

I need to get me a cordless one. I hate cords lol. Thanks for watching and commenting 👍🏻

[@mxr248]

If you guys don’t have an impact of some sort but have a hand held little propane torch heat around the bolt and they come out a lot easier..

[@JustinsProject]

Great tip! Thank you for watching and commenting! 👍

[@gane4318]

I put little grease on bolt and it's easier to get them off

[@JustinsProject]

Thanks for the tip!

[@oooomoment5739]

OOoo... the blades have to be lined up in a specific pattern to get optimal cutting, Really enjoy your videos. Thanks

[@JustinsProject]

My yard is not optimal mowing coditions either 😁

[@lorenpinger3925]

What's the pattern ?

[@gailp9432]

Good video. Thanks for keeping it real.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@clarencemc3rd295]

Amazing when you slow ground speed down

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@gregjohnston3421]

Never had a problem, first use the box end, impact works so much better.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@roberthester5379]

Impact wrench is the way to go With this

[@JustinsProject]

Definitely! Thanks for watching and commenting 👍🏻

[@bwoutrage21]

Again a great vid. If I buy one of those mowers I will have the dealer remove the blades and hand tighten before I take the mower. Just stupid on the Bad Boy Factory's part. Guess they just want people to come back to the dealer to change blades.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@rayburnett3066]

I use the side angle as you call it

[@JustinsProject]

😁 Angle ... aka "side" grinder... Thanks for watching and commenting 👍🏻

[@jlor7675]

I've decided to go with the Maverick after a month of research. Ask the dealer to do the initial blade removal before I picked it up so hopefully I wont have such a hard time changing blades the first time.

[@JustinsProject]

Congratulations! The Maverick is a tough mower. You will love it. Thanks for watching and commenting 👍🏻

[@scottmckisson936]

I'll just use my milwaukee impact driver. 😂

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@David-de3ed]

Good impact gun and impact six sided socket and ten minutes. ps you won’t believe how easy it is to pull the Deck so you can change blades and clean the unit.

[@philritzenthaler4543]

1. Good God!! Use a mower lift and use an impact drill. (MoJack MJ-PRO 750-Pound Lift for Tractors and Zero Turn Radius Lawn Mowers) 2. Use ANTI-SEIZE on the bolts. I cut @ 4.5 acres out of our 5.6 acre property and change the blades on my Maverick @ 6 - 8 weeks. I use Oregon G5 Gator Blades on my mower (it’s a thicker blade). I also sharpen using a cordless angle grinder with 60 grit flap disks. Finishing with a couple passes of a file. Not bad for 71. Work smarter, not harder.

[@JustinsProject]

Good stuff! Thanks for watching and commenting 👍🏻

[@JimLindsey-yq2wy]

Highly Recommend!!

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@paulshipley8854]

Avoid using open end of a wrench on tight bolts.can round them off

[@JustinsProject]

True. Thanks for watching and commenting 👍🏻

[@bassplayaman1]

Two words: Impact wrench. Only way i could get mine off. I talked to the folks at Badboy and they said to use one to get the bolts off. Don't use one to put it back on. Just tighten it with a wrench and use a torque wrench to the correct torque. My manual said 90 to 110 foot pounds, so i tighten it to 100.

[@JustinsProject]

Even on my last change the electric impact will not remove one. I have to torch the bolt then hit it with an impact. Thanks for watching and commenting! 👍

[@theodorekeefer1093]

I try to use the 6 point socket and breaker bar or impact makes things easier at least for me...

[@JustinsProject]

The impact works great. Next time, I'll lift it with my tractor, lol. Thanks for watching and commenting 👍🏻

[@josephcushman454]

Need to torque bolts to bolt size , factory must have a gorilla tightening those bolts , I apply grease to treads before reinstalling to keep from any kind of corrosive from threads, makes it easy next time , use box end wrench to keep from slipping and keep from going to emergency room .

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@ronnieabor1514]

Get you a piece of pipe that will fit over you rachet or brake over bar as a longer extension. That leverage will enable you to remove it with ease

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@rupertwelch893]

Never use the open end side always use the box end of a 9 point socket and never a twelve point on something that tight I always use a ratchet and a two foot cheater pipe much easier Brother

[@JustinsProject]

Much appreciated 🙏 Thanks for watching and commenting

[@christal-ball]

Next time soak your bolt for a few mins with wd40 and never sharpen blades, they seem dull because they are painted. The sharpen with use.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@brentjohnson6654]

Awesome video, both the mowing test and the blade changeout. I am hoping my impact wrench can take out those bolts, if not, then maybe a helper pole on a breaker bar. It is all a matter of physics, right? Haha I purchased a lift for my Bad Boy but with all the weight on the back, I would rather have way to keep the front tires from going vertical if it falls on its back. Speaking of being back heavy, I usually drive it on my trailer backwards so I am not trying to pop a wheelie (note I don’t have a ROFS bar). Again, good video. I am designing my own solar for our homestead here in north Texas. So we have both Bad Boy and Solar in common. Cheers!

[@JustinsProject]

Awesome stuff! Hope that your solar project goes well also. If you can do it yourself you will save a ton of money.

[@brentjohnson6654]

@@JustinsProject thanks. I am planning on doing most myself. I may hire an electrician for grid tie in and some manual labor for setting the ground mount poles. I have used Iron Ridge site to design the ground mounts. I am leaning toward 32 panels for total coverage and may start with a lower number for backup power mainly. I am a Ham Radio operator and concerned about radio interference so I am testing some installations with micro inverters, different MPPT controllers. Also am wanting to make sure I have a welder/shop tool friendly inverter. Also I have a couple of HVAC units (3T, 5T) that are relatively easy on startup surge in comparison to older ones, but that is some consideration. I don’t say I know it all, so I do like learning. What inverter were you using? If you are on micro-inverters, I assume you are using AC coupling on your inverter. You don’t have to feel obligated to explain the whole system if you have videos I can watch *hint*. Lol. I have a lot of ideas and desires for solar and the like, so we could sit down with a drink in hand and discuss all that we both know. Haha

[@DavidLee-vq7vj]

Yes my 60" done it from day one had back to the dealer twice and still does not quite right have to do at least twice or half half a pass on each run

[@JustinsProject]

Thanks for sharing 👍🏻

[@robertconville6269]

You are not mowing grass you are mowing weeds and there is a big difference in that weeds have tough stems also get a mower Jack from Harbor Freight I use it on my maverick I drive on it and it lifts it so high it is easy to access the whole deck

[@JustinsProject]

The field was pretty rough last year. Once we got it mowed and kept it mowed, this year, it's not as bad. It's a work in process. You are right. There is a massive difference in mowing stalks vs. grass. I'll have to check into the HF mower jack. Thanks for the tip. 👍🏻

[@thomasjohnson1222]

When sharpening blades make sure u do each edge equal sharpen for proper balancing to not have vibration. When you finish sharpening both edges take a screw driver n put it in bolt hole ,the blade should be horizontally balance it one side is lower than the other side u should sharpen lower end as it has more metal than other side

[@JustinsProject]

Thanks for watching and commenting!

[@mikepirrone97]

Get ya a 4ft metal pipe to slide over your wrench. Would be like using a 4' long wrench. That will give way more leverage.

[@JustinsProject]

True, thanks for the tip 👍🏻

[@southernokie3430]

Sorry I got a a frame makes it so much faster safer and can get right up there

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@ronaldmcdonald8894]

might want to get that torque wrench calibrated.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@ronaldmcdonald8894]

@@JustinsProject thanks for replying without reading

[@garyhasseberg9921]

Never ever use an open end wrench but if that's all you got you have to, and if you have an impact socket use it because it is heavier and they are a hex socket or six point socket and heavier than a regular socket and an impact wrench if you have one, and of course the six point socket won't round the head of the bolt off either, but you already know all of that though

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@j.davidwilliamson1163]

I just changed my blades for the first time and could not break the bolt loose, finally used an impact gun and let it keep beating the bold head, stopped and repeated again and it finally broke loose. The other two were easier to remove with the impact gun. Also, Justin get yourself a pair of car ramps, I use the heavy-duty hard rubber / plastic ones. I had to use a small jack to raise it high enough to use the impact gun, but once the bolt has broken loose I was not able to take it completely off because of the height. Loose enough to take off by hand then. I tightened them with the impact gun until it stopped probably 100 ft. lbs. My bolt head used a 15/16" 6 point socket.

[@JustinsProject]

The last time I changed them, I had to torch the bolts. Crazy how tight they get.

[@michaelmorse5818]

Just another tip when you sharpen the blades that way they sure did you got them balanced and I just checked mine on a nail hanging on the wall. Be sure I get them pretty balanced that why you don’t throw your spindles and stuff out of whack and all that my Babe calcium more money better.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@mikepici5553]

Get yourself a blade balancer,for whenever you resharpen and try a 60 grit flap disc an your angle grinder, you got less chance of over heating the blade, also im in the market for a new mower myself and im loking the maverick hd.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@danielkerens129]

I would like to add my comment… using the techniques of loosing bolts per these suggestions makes the change out very time consuming. Above the blade have flats for a wrench, this is 1 1/8” and the flats are 5/16” wide. I used a 12” wrench, fits perfectly to insert between the blade and the blade housing. With 2’ breaker bar, 5 seconds everything is loose.

[@danielkerens129]

Message me if you want details

[@JustinsProject]

Thanks for the tip. Thanks for watching and commenting 👍🏻

[@PRS-0317]

@@danielkerens129 I'm curious how you do this. Pictures maybe of how you place your wrenches?

[@nvrdwn3140]

It is as simple as three bolts on and off when you have a battery impact. Zips them right off and you can easily hold the blade with your hand even the fresh sharp ones.

[@JustinsProject]

Thanks for watching and commenting

[@nvrdwn3140]

@@JustinsProject Get a battery impact it made the whole thing way easier for me!

[@fredhart7904]

I had a similar situation with my bad boy elite with Kawasaki engine, Could not get the end cap off the oil drain tube, Finally had to call a friend with some heavyweight tools, We finally got it loose and drained the oil What a pain in the butt it was, must of had a 400 lb gorilla tighten the oil drain hose end caps that production day,

[@fredhart7904]

Also, I am on my second season and I have never chained my blades, But it still cuts good, do not mow that large of an area,

[@JustinsProject]

Sometimes, it's not always as simple as it should be. Just yesterday, I changed the blades again, I used an impact, and it would not remove the right side blade. I had to torch it to remove it. This time, I lifted it with my tractor, though. 😁 Thanks for watching and commenting 👍🏻

[@mikezupancic2182]

Power tools make life easy. Thats a 10 minute job.

[@JustinsProject]

The right tools for the job were locked up in storage. 😁 It should not take 5 minutes now. Thanks for watching and commenting 👍🏻

[@MrZipperhead16]

There's no reason for the bolts to be that tight, even from the factory. A little anti-seiz on the threads, snug them up and give them a little extra umph and that's all you need. The blades spin against the direction of the threads so they keep themselves tightened. Yes, sharp blades will cut better than dull ones.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@j.davidwilliamson1163]

Watching your video more, I see that there is no place to hold the blade while trying to loosen it. I owned an Exmark 60" cut before and to change the blades the spindle had two flats that fit a 1" wrench and the head size of the bolt was 15/16" so it made it easy to change the blades, these new mowers don't give you that option and make it harder to change blades. Come on people work with us we are not taking it or having it picked up to change the blades at a ridiculous price.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@robertduncan2742]

Id use the bixed end then take another boxed end to the open end. Theres plenty of lrverage. Those were most like torqued or impaceded on

[@JustinsProject]

This last time I took them off the impact would not remove them. I had to torch the bolt and still was hard as hell with an impact. Thanks for watching and commenting! 👍

[@kevinlee7811]

Trials and tribulations of a modern home owner

[@JustinsProject]

🤘 Thanks for watching and commenting 👍🏻

[@nickikarr2613]

Not sure if you're still using that or not to change your blades Ballard products makes a lift it holds it up and locks it in place where you can use a impact

[@JustinsProject]

I'll have to look into that. Thanks for watching and commenting 👍🏻

[@rayburnett3066]

Personally, I love those gate blades

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@harryerhart5978]

Torque your blades to the correct tightness 70 to 75 lbs using a torque wrench 😊

[@JustinsProject]

Good tip. I'm definitely going to put the proper torque on them next time. I have a good quality torque wrench that I dug out of my storage.

[@butter7506]

Have to say if I change mine and have to go through that. My swear jar is going to be full.

[@JustinsProject]

🤣 ... Thanks for watching and commenting 👍🏻

[@darrenhughes8106]

Good info. Is the Kohler engine still doing good? Any problems? Thanks

[@JustinsProject]

Doing great. Setting a little over 200hrs now. Thanks for watching and commenting 👍🏻

[@darrenhughes8106]

@@JustinsProject thanks for the reply. I was on the fence about kohler engines but they do have a three year warranty. The dealership is just down the road from me.

[@eugenejohnston3512]

I use a mower lift and battery powered DeWalt impact, and takes me less than 5 minutes to change blades. If the battery needs charging, I use a cheater pipe on my ratchet with 2×4 block. Takes me maybe 7 minutes with the pipe on a ratchet.

[@JustinsProject]

Good stuff! Thanks for watching and commenting 👍🏻

[@ericg4x4]

Why would you not use the boxed end of the wrench?

[@JustinsProject]

😁 No idea, I wonder if that would have done the trick. We will never know 🤣 because it's always going to be the impact from now to the end of time. 🤘

[@Gipper3670]

That is the very reason I always use Anti-Seize,,,,,, you will never have that problem again if you use it every time you change blades

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@stevejuststuff2779]

Good video. Liked and subbed.

[@JustinsProject]

Awesome, thank you!

[@kyledeman2851]

They really need to do some QC with those blades coming out of factory. My impact that has 220ft lb torque wont budge the bolt. Completely unnecessary.

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@davidhabener5767]

Don't forget anti-seize compound, you'll never have that problem again. save the threads.

[@JustinsProject]

Appreciate the tip. Thanks for watching and commenting 👍🏻

[@harryerhart5978]

That happens when you hit something 😊

[@JustinsProject]

And when mowing 6.5 acres almost every 10 days or, its bound to happen.

[@ky_chevy2824]

The time it took you to grab all them tools and not successfully take them off you could’ve put the jack on mower deck jacked it up and it used a impacting gun would’ve been done in 10 minutes tops

[@JustinsProject]

🤣 Thanks for watching and commenting 👍🏻

[@thomas25082]

Hindsight always 2020

[@rayburnett3066]

You, my friend is just like me.

[@JustinsProject]

Thanks for watching on commenting 👍

[@rontopping2048]

Bad boy mowers don't lay down a good cut anyways. Toro , exmark Wright or Walker is where it's at

[@JustinsProject]

My main negative on this mower is the traction. From what others tell me that is an issue on all ZT's other than the Altoz. I don't know though, I am no professional.

[@oooomoment5739]

I do have a 3 blade mower that is belt driven and those blades do not change their alignment after a. year of use... odd to hear some are saying it makes no difference. YMMV ;-)

[@JustinsProject]

If the operator is mowing thick fields it is possible the spindle/belt may slip. Changing the alignment. It may not be common but under the right conditions it could. Probably me mowing a field like I did at 6ft tall, it could be possible.

[@CharlesCollier-kp7km]

Impact wrench! Off in seconds!! On "safe" harbor freight lift". So simple! Why the jerry rigging? Some people just don't get it!!!😂😢

[@JustinsProject]

😁

[@charliedemler2979]

I'm having the same problem getting 2 of my blades off my 48" Bad Boy. I was thinking about heating the bolts with a torch to try and get them off. Hoping it helps.

[@JustinsProject]

You mean it wasn't a 5 minute job for you either? 😁 I'm sorry to hear that because when they get like that, they are hard as hell to get off. Goodluck! Thanks for watching and commenting 👍🏻

[@charliedemler2979]

@@JustinsProject I got one more off but the middle one isn't budging. Even after hitting the bolt with a torch. Not sure what to try next?

[@sterlingmiles1948]

Man, just use an impact. I have a commercial business and use the Rebels. I just use a milwaukee impact. Best part is the impact does not turn the blade so you do not need to secure the blade.

[@JustinsProject]

The electric impact would not remove them the last time I took them off. I had to torch the bolts. Not sure way they get so friggin tight as I use it. Thanks for watching and commenting 👍🏻

[@georgemarshall5675]

Why not just use an impact wrench to take off the blades ? Saves so much time and effort!

[@JustinsProject]

True lol thanks for watching and commenting 👍🏻

[@jlor7675]

How many hours did you have on the mower when you need to change the blades?

[@JustinsProject]

I changed them because I wanted to try mulching blades. Plus, my other blades had skipped over the top of my concrete driveway. I will be sharpening those old blades and putting them back in action a little later in the growing season. Thanks for watching and commenting 👍🏻

[@justinking7331]

Olk that's tight enough try loosening it now

[@JustinsProject]

Thanks for watching and commenting 👍🏻

[@jamesfilippellosr.8825]

Buy a zero turn front end lift, they are maybe $150 which will give you plenty of clearance. Next, always use an impact tool with some serious power, I recommend a pneumatic impact gun. It takes no longer than ten minutes for me to swap out three blades, using the proper tools. Your struggle with pieces of wood and wrenches was entertaining. You are suggesting this to others, so why not do the job right.

[@JustinsProject]

Thanks for watching and commenting

[@harryerhart5978]

American blade sharpener about 100 dollars you will keep your blade angle at 30 degrees 👍

[@JustinsProject]

Thanks for the heads up! I will look into that. Thanks for watching and commenting 👍🏻

[@popatop6657]

The box end is your friend.

[@JustinsProject]

Just changed them again. Impact would not remove one. Had to torch it, and it came off easy. Thanks for watching and commenting 👍🏻

[@royalbertson7260]

Mine were that tight too and its not right to come from the factory like that. You didn't grow up on a farm, some grasses and weeds are harder to cut and you need to go slower or mow before they get that big.

[@JustinsProject]

Thanks for watching and commenting!

[@no_handle_required]

Funny thing is, my original blades worked perfectly, i knicked one so I though why not replace them, and the new blades are leaving strips of grass uncut.

[@JustinsProject]

That's unfortunate, the new blades I put on are performing great. Just mowed the lawn today and it shredded the grass nicely. Thanks for watching and commenting 👍🏻

[@ready4anap]

I think this has been identified by another you tuber as the PTO pulley being too small and causing the blade speed to be too slow. This guy....kzbin.info/www/bejne/aXyQnn9vrtp0m5Y

[@ridgeriderrc761]

Probably got too short of blades

[@thomasworrell6853]

This has to be a parody. I’ve never seen so much extra effort to get blades off of $10,000 lawnmower. 1/2 Milwaukee impact with a 15/16 socket can change those blades in five minutes and that includes the time to hook it up to a chain hoist and raise up the front end into the air. My knuckles hurt just watching this video.

[@JustinsProject]

I have all my tools out of storage now and in the shop. Including the 1/2 impact and 6 point socket. Never does it come off that easy. Sometimes I have to torch the bolt and use an impact. Ridiculous. Never had this issue with a mower before. It gets locked on after using it just a couple times.

[@tiptoesparadise7517]

Maybe we can remove the deck and turn it over? I may look into this.

[@JustinsProject]

The deck is VERY heavy. 7ga solid steel. I'll probably just lift the mower with my tractor forks next time 😁

[@MrLewisb33]

Seems like bad boy never intended for us folks to change those blades ourselves.🤣

[@JustinsProject]

BUT when we mow with attitude they should expect us to change blades with attitude 🤣 Thanks for watching and commenting 👍🏻

[@mikehill9050]

Man it was killing me to watch this. U need a set of car ramps and a cordless impact

[@JustinsProject]

😁 It hurts to think about it 🤣 Thanks for watching and commenting 👍🏻

[@miked8227]

No watched you miss the tall stuff on your dull pass. I wouldn’t ask my machine to mow that tall field at high speed. I know you were doing it for a demo but, I’d never consider mowing it at that speed. Anti seize on those threads for future removal.

[@JustinsProject]

😁 I have another video where I ended up mowing the entire field at much higher levels. Not something I will do again but it was a good test of it's capabilities. Thanks for watching and commenting 👍🏻

[@jeremypriest4062]

Wrench extender or cheater bar. The sledge just makes me laugh.

[@JustinsProject]

Thanks for watching and commenting