I swap the servo in my 4l65e and compare the difference. Definitely recommend helped 1-2 and 2-3 shifts
Пікірлер: 53
@kennyman3383 жыл бұрын
Great positioning of the camera to show a how to install a servo. 👍
@abbondanza233 жыл бұрын
If you use this mod for higher shift rpms through the gears, I'd recommend an after market Trans fluid cooler, the transmission will get WAY hotter shifting at higher RPMs consistently, causing premature 3-4 pack clutch burn. That is what the Corvette servo provides, longer band grab in each gear before it shifts, for quickest acceleration to top end speed
@julianoliva28503 жыл бұрын
Very good advice Jon... Recently i bought a 2011 chevy Colorado 2.9 and started makin some upgrades to a callejero street drift truck so i upgraded the diff to posi with 4.10 gears but looking to lower maybe to 3.73 and already put a transgo hd shift kit; bought the super servo 2-4, an B&M "quicksilver" floor shifter and now looking to get a nice transmission oil cooler/efan... what more can u recommend for a 4L60e involved in a higher performance level thanx bro. 🍀🎶🍻👍
@bonacjunk9983 Жыл бұрын
jon sorry i am late to respond to the comments, you are right it did bring the temp up need to add a bigger cooler with the corvette servo
@mathewhunt813 жыл бұрын
wow! best video i have seen of anyone doing this !
@Reviewerguy12284 ай бұрын
Bro… perfect Escalade… I have an 03 on 34”s and 3 inch keys
@markbauer93933 жыл бұрын
Best video I've found, thanks
@MrChucky26853 жыл бұрын
man nice video i wasn't sure of doing this mod and watching you and went straight to my 01 tahoe ...i have it lowered on 26'' 4/6 drop and all stock ,bore out my throttle ,cold air intake,no cats,performance muffler ebay, and dam near ever thing new on block sensors and what not and she gets up there,, Passing gear ,getting on freeway way and torque is on points ,smokes 6's like nothing now ...what yall waiting for DOOOOOOOOOOOO ITTTTTTTTTTTTTTT...
@Lostsoul.6682 жыл бұрын
0:20 in hold up. Are we long lost friends? i cammed and lifted my Escalade too, hands down I’m a sub 👍🏽
@tjmoneybags2 жыл бұрын
the lesson to pay attention to here is.....if the clip wont go in on the outside....you don't have it on right or in all the way. When it is in all the way, theres plenty of room for the clip.
@zombieapocalypsecherokee92243 жыл бұрын
I have 1 of these Corvette piston kits coming for my 03 suburban and I have to admit I'm nervous as could be I hope it goes as well as you make it look Thanks for sharing 👍
@CPT3103 жыл бұрын
I just did my 2002 Tahoe z71 , took me a bit to take it out , there’s not much room like in this video,
@zombieapocalypsecherokee92243 жыл бұрын
@@CPT310 I haven't done mine yet. I have a hard shift from 1 to 2 its been that way since I bought the suburban 2½ years ago hasn't got worse or better im hoping this will help 🤞. How did it do on yours?
@Idontwantaname31310 күн бұрын
I’ve been catching hell putting my snap ring back on. Now I see that I may need a longer pry bar.
@Glock2093 жыл бұрын
Use a pick pull the blue O ring out then the cover will come off
@kotyriall21342 жыл бұрын
Love your caddy bro I got an 2004 awd black exterior with gray interior Love it just would like to do some mods to make it better and last longer
@edwinj82753 жыл бұрын
Your Escalade is sick!
@bonacjunk99833 жыл бұрын
thank you
@james1023772 жыл бұрын
I hope you watched this video because I'm pretty sure that clip wasn't in all the way.
@bonacjunk99832 жыл бұрын
it was in ben driving over a year fine
@james1023772 жыл бұрын
@@bonacjunk9983 was just in video, the bottom of the clip disappeared into the housing into the groove and you could see the top of the clip clear as day looking like it never made it into the groove. My servo just came in today but I work nights. Supposed to be in 90's the rest of the week on my days off so not sure I want to get out there and mess with it. Have to do a wheel bearing too...lol
@james1023772 жыл бұрын
@@bonacjunk9983 i just tried installing a vette servo in my Hummer last night. Everything went okay at first. The cover gave me a problem but then my shifting was all screwed up and felt like I might've did something to 2nd gear. I went to pull it all out and had to use a pipe wrench to get the cover off and it took me 2 hours to get the piston out. For some reason it was stuck. I had vice grips on the shaft and pry bar under that and finally it came out. Not sure what happened but it's not going back in that's for sure. I just had to hunt down new o-rings today. Luckily I found a tranny shop that just gave them to me. I almost think they put the wrong o-ring on the piston because it looked exactly like the cover o-ring, same color and all. The tranny shop gave me a blue and red and the red is definitely smaller than the blue. The vetter servo doesn't have any red o-ring, just the 2 blue. Either way I'm not taking chances again and need to know if 2nd gear is screwed. I just put this tranny in 3 weeks ago so I'll be pissed if it is junk.
3 жыл бұрын
Sweet thanks man next in line is this mod
@ronniejohnson16342 жыл бұрын
You can adjust the screw on your epc solenoid 1/8 turn clockwise shift much firmer
@moycorral787010 ай бұрын
More info on this ?
@deeeeeeps Жыл бұрын
Great footage..mine won't spin or move thought I was doing something wrong.
@billhartsfield4249 ай бұрын
What you were missing was watching a KZbin video that shows you how to do the job. Ie, remove the o ring to remove cap.
@jaydemorgan5694 жыл бұрын
That’s sick!
@crazyhorseracing61303 жыл бұрын
Do you have a part number?? Thanks for the video!!
@dakosyoutube62323 жыл бұрын
Does this remind anyone else of when tony starks wife was switching his heart out in iron man 1
@smithjo4152 Жыл бұрын
Hello, thank you for your video. I'm struggling with that servo install. Any suggestions on how to hold pressure against the servo case while trying to install the rigid C clip?
@bbodybeedy1610 Жыл бұрын
I used my baby moma for help . Worked like a charm
@smithjo4152 Жыл бұрын
@@bbodybeedy1610 Hilarious 😂
@bbodybeedy1610 Жыл бұрын
@@smithjo4152 deadass tho lol
@yesode42012 жыл бұрын
Rattle can red full race!
@jram927 ай бұрын
How’s it performing now ?
@geronimemo5 ай бұрын
simple to the fact no BS excellent video
@seangowan74412 жыл бұрын
Is it easy? How long did it take you install?
@JavierTorres-yk8fj Жыл бұрын
What year of corvette trans servo did you use
@googlemall33233 жыл бұрын
I'm curious as to what vehicle this is on because in my 2003 Yukon there is no way you can get the servo out without having to drop the transmission or bang your floor pan in
@Mr_Ruhl3 жыл бұрын
It's an Escalade obviously. LoL. However in the vid he states that there's a body lift (didn't say how many inches) on it so that is giving more clearance room between the cab & tranny/frame.
@marcell5055 Жыл бұрын
Amazon
@Devo19873 жыл бұрын
so will this speed up the shifts going up hill's make it move thru gears sooner ?
@bonacjunk99833 жыл бұрын
yes firmer faster shifts
@abbondanza233 жыл бұрын
@@bonacjunk9983 That's interesting when I installed mine, it holds each gear all the way to 5500 rpm, but that is because I get on it
@seangowan7441 Жыл бұрын
Did it firm up 3-4 shift too?
@bonacjunk9983 Жыл бұрын
sorry for late reply, yes overall firmed up all shifts but does bring trans temps up a bit recommend bigger trans cooler after this upgrade
@matthewverity57424 жыл бұрын
Hey my name is Matt
@mathewhunt813 жыл бұрын
yeah? me too. and....?
@Jesus713martin3 жыл бұрын
Where do you buy this servo at ?
@bonacjunk99833 жыл бұрын
ebay
@DaveNorthWest Жыл бұрын
Your suppose to take a pick and cut the oring then pull it out with nettle nose plie then this video would of only taken a 1/3rd the time
@bbodybeedy1610 Жыл бұрын
Depends. I pulled mines out with the oring still attached