Craftsman Tractor Won't Start

amzn.to/3FhE0L2 Intek replacement carburetor
amzn.to/3M28qEP Channellock electrical crimping pliers
amzn.to/3Ficptm Battery Terminal Ends Storage Case
amzn.to/3ZTI39M Hydraulic battery terminal crimping tool
Help support Doublewide6 Repairs LLC by sponsoring his Patreon Account
/ doublewide6
Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC.

[@terrycapehart6303]

Your a ruff ol dude, but a hard working man , have a blessed day América

[@bigsonslawncare]

Pressure wash! Double the value! 😂 Love it😂👍🏽

[@danielpadgett2831]

😂

[@tonym6920]

Nice work DW6, 👍👍. Thanks for the vid!

[@freedommowers420]

I have learned a lot over the years on your channel. Thanks for the upload and information as always DW6. 😎🇺🇸

[@crisprtalk6963]

Getting your DW6 fix I see Alex. Nice.

[@freedommowers420]

@@crisprtalk6963 absolutely. Some great content on this channel. 😎🇺🇸

[@watermanone7567]

Nice fix. I had a hard time getting compression release cams last year. Have not tried this year. Thanks for the video.

[@jeremyanthony9300]

I look forward to meeting you Bob.

[@Big_Johns]

Turd polished, good job Bob. 👍👊

[@chuckb.5076]

Great video! Hope to see the vid on the decompressor. Thanks

[@doublewide6]

I got lucky you didn’t need it. I just adjust the valves. Took care of the problem.

[@nashguy207]

Good job Bob. Keep up the good work and videos!

[@doublewide6]

Thanks, will do!

[@mikespain8655]

I have repaired two broken compression release mechanisms this year. Pretty straightforward repair, but it takes time.

[@doublewide6]

Turns out it just needed a valve adjustment

[@chadfield376]

Yes, please do video on how you would do the compression release replacement:-) Also liked your needle seat honing tool and method also!

[@jeffsandler3339]

Enjoyed the format Bob nice work as usual !!

[@doublewide6]

Glad you enjoyed it

[@Turningwrenches85]

Nice work on this craftsman bob 👍

[@philliphall5198]

Nice trick on seat and needle Thank You, will save money 😊

[@jameslane7922]

Nice video. Love that needle seat honing tool. I've got to make one of those. Like others, I noticed the backwards gas tank right away, but I was more curious about the placement of the shutoff valve. Doesn't it make more sense to place it in front of the fuel filter? That way you can just turn off the fuel when you need a new filter, instead of draining the whole tank. 🤔

[@doublewide6]

Usually I put the fuel shut off first then I can change the fuel filter when servicing the carb. I have another video on how to make the honing tool.

[@ackack1]

Nice fix. Luckily, that Intek came with a Walbro carb instead of a Nikki. I have the same engine on a 2008 Yard Machines & I swapped the factory installed Nikki with a Walbro off a neighbor's Murray that threw a rod. Runs better with the Walbro. For what it's worth, my Briggs manual says it's 48oz of oil if the engine has a filter & 44 if it does not.

[@henrymurawskibigdogrepair]

Bob I was tapping you on the shoulder through my computer to let you know you put the gas tank in backwards

[@doublewide6]

Thanks and please don’t call me Barb

[@robertmailhos8159]

Glad you gave it a good cleaning nothing like a dirty mower that you are working on it is better to clean it up before you go to work on it

[@mjshuja1948]

I WATCH YOUR VIDEO ALL THE TIME 👍👍👍👍👍I AM ALMOST 80 YEARS OLD WORK ON ONLY GERMAN CAR👍👍👍👍NOW MY SON BUY ALL KINDS OF MACHINERY 😱😱😱😱😱I FIX THEM 👍👍👍👍THEN HE SELL ✌️✌️✌️✌️FOR THE LAST TWO ✌️✌️✌️✌️I AM LEARNING HOW TO WORK ON SMALL ENGINE😱😱😱😱IT IS DIFFERENT FORM GERMAN CARS 😱😱😱😱HE EXPERT BUY AND SELL ALL KIND ZERO TURN👍👍👍👍

[@TheCaperfish]

few tips , use mopar penetrating fluid to soak yer jets in and spray into all cavitys of carb and let sit for an hour then just spray out with brake clean , it will eat everything , trust me its a must try if working on carbs a lot , I don't even use weak carb cleaner or ultrasonic anymore Another thing when finished repairing a carb especially needle and seat issues , put carb on studs but don't tighten up yet , leave a gap and then hook gas up . leave it for a while and you will see if its bypassing needle as it will drip out instead of secretly going into cylinder , when doing this test fill gas tank full so you have the max amount of pressure of gas against it . Always pull off motor cover and look for nests on top of cylinders when getting a barn find mower that hasn't been run in a while , some times ya can't see em from outside , you will smoke the engine fast if fins are covered .

[@liljoeii6091]

Thank you for the video bob

[@doublewide6]

No problem happy you enjoyed it

[@wtbm123]

Cool

[@crisprtalk6963]

A smiling DW6 in the thumbnails is no good. I need to see torment, frustration, angst!! 🤣

[@chet3larson]

Keep making that money dad, lol. Love it

[@billsmith1770]

i tried to start one that the crankcase had been flooded , it backfired . i walked away to get something , returned to find the muffler on fire . luckily , i wasn't gone long . i guess the muffler could've actually exploded . ever since , i try to remember to blow thru plug hole w/exhaust valve open , to dry out the muffler 1st .

[@billlovett4256]

What brand and model lift is that please?

[@jackcollins2344]

Your pressure washer looks like it did an great removing dirt and grime . What is the size and brand of you pressure washer you are using now days, and how do you like it?

[@doublewide6]

I think the brand is tenda it’s about 3000 psi. It has been working pretty well for about three years and I’ll leave it outside except in the winter. I switch the metal tag with a plastic tank because the metal tank kept getting water in it when it rained.

[@jackcollins2344]

@@doublewide6 thank you , I'm in the market for buying a pressure washer now to have next spring and thinking now might be a good time to buy for hopefully a good price

[@adnacraigo6590]

Do you think that you will be able to get the dents out of the hood?

[@doublewide6]

About three taps with my first and they came right out and then I had to bend a little fins a little bit toO

[@philliphall5198]

I AllWAYS remove plastic cover and clean out trash or mouse nests Best just to make sure it’s not over heating 😊

[@trebsr]

Could be valve adjustment?

[@doublewide6]

It was just valve adjustment to fix it.

[@trebsr]

@@doublewide6 awesome been there lol

[@beanolatte2682]

Good videa!!

[@danielpadgett2831]

The valves probably need adjusting

[@lasersbee]

31:33... Probably no more oil in the crankcase...😉

[@rverro8478]

26:53 That's why I'm divorced.

[@rogerveium3753]

You know what they say. Marrige is grand but divorce is 100 grand!

[@ctbale1]

200 Amps?? That's a bunch!

[@philliphall5198]

I’ve been married to same sweetheart for 51 years and we’re still together and enjoying it together 😊

[@rverro8478]

@@philliphall5198 Congratulations.