Crane Hook | Boundary blend | Surface modeling in Creo Parametric

This tutorial is about surface modeling in Creo Parametric. In this tutorial, you will learn how to create a crane hook using boundary blend in Creo Parametric. Boundary blend is a powerful tool for surface modeling. You will gain insight into creating the crane hook through surface modeling using boundary blend in Creo Parametric. So let's get started.
Join this channel to get access to perks:
/ @cadxtraining
Playlist:
• Part Design in Creo Pa...
• Complex part design in...
• Sheet metal tutorials ...
• Surfacing in Creo Para...
• Plastic Design in Creo...
• Assembly Design in Cre...
• Detailing the drawing ...
• Gear design in Creo Pa...
@CADxTraining #CADxTraining #CADx
/ @cadxtraining
/ cadxtraining
t.me/CADxTraining

[@vickyoo5]

Very informative I'm learning lot. Thanks in advance for the future videos

[@edzak7257]

I, too, had trouble in getting the boundary blend to work using all 3 sketch references. To solve I did this: 1. Boundary Blend: Profile sketches #1 & #2 2. Fill both ends of blend from step 1 3. Merge blend & both fills, then Solidify 4. Create Revolve (Nose of hook) 5. Boundary Blend edge of revolve & center profile sketch 6. Merge blend from step 5 then Solidify 7. create last revolve, hole, cosmetic thread & chamfer Done!

[@CADxTraining]

Good

[@user-dy9ve8pr7p]

I like your videos😊

[@ROHITmq3rp]

Best tutor.

[@rafaelalmeidafioravanti4834]

Congratulations on the course. Thanks. I am learning a lot. Do you have a video on how to make a 3d drawing a 2d one with dimensions? Just like the drawings you use to draw.

[@joseaidhernandezdominguez4233]

God, you're the best

[@cherylveliganio6601]

I'm having difficulties with this but still its so helpful. I will redo it many times till i able to get it. I'm having difficulties with the datum plane

[@CADxTraining]

Change the file accuracy to 0.001 and try

[@swarajbiswas3056]

Hello sir. Can crane hook be modelled with swept blend or blend ? I have tried several times, but goal is not accomplished .

[@CADxTraining]

No, it is not possible by swept blend are blend. You cannot maintain all the dimensions using swept blend. There are two guide curves in crane hook. If you use swept blend you can only maintain One guide curve.

[@Kaalathekaali]

Sir everything fine at last after boundary blend if i select tangent it shows error if its free its ok what to do?

[@CADxTraining]

Change the file accuracy and try.

[@chezhianj8117]

How do you keep your drawing on left and sketching

[@harikumark6371]

Hello, I am getting error like "try adding curves between curves no.0 and No.1 in the first direction" while adding nodes in Boundary Blend, can u help me with that? @CADx

[@CADxTraining]

Your path and sketch section must be connected with each other to form the boundary blend. So create datum points on the path and take the reference of these datum points while creating the section. You will not get any error. Watch the video carefully to see all the steps followed.

[@adityagodase1485]

Try by using two control points

[@ranjubala5732]

How to add auxiliary view arrows in creo?

[@CADxTraining]

Why you need that?

[@ranjubala5732]

@@CADxTraining For indication of direction of auxiliary view from parent view just like section arrows.

[@CADxTraining]

Create a symbol for import as a symbol to creo parametric

[@madhavabonam1019]

I find this tutorial was very helpful, but I am unable to form a boundary blend with the third section at the revolve. When I select the top and middle section(sketches), shape is generating, but when I click for the third section as profile of the revolve it's not showing any preview. Could you please help me out if I am making some mistake. I am getting some preview if I don't select the paths, but to get the required shape the blend is not generating with the paths.

[@CADxTraining]

Change your part accuracy first. Make it 0.01

[@madhavabonam1019]

@@CADxTraining I tried changing the accuracy to 0.01, but it's not working yet.

[@CADxTraining]

Just give a last try. Change the accuracy to absolute and make it 0.0001

[@madhavabonam1019]

@@CADxTraining It's still not working, I will start from scratch once again and will see if it works. either way thank you for the quick reply

[@Rajesh360]

in youtube less video available about creo

[@manishshekhawat5529]

HI Satyendra, I am trying the same way you showed here but my blend is failing in 2nd direction. what to do?

[@CADxTraining]

You need to increase the file accuracy I guess!

[@manishshekhawat5529]

@@CADxTraining may be. the blend is complete upto initial two sections but it is failing when i connect to revolve section.

[@martinmartin4974]

Can u post how to install creo?

[@CADxTraining]

You need to search in KZbin. Already there are several videos available.

[@martinmartin4974]

Ok sir👍

[@sonuKumaryadav-ld7qz]

Hello sir I'm unable to make it while I'm putting control points it's not giving results

[@CADxTraining]

Change the part accuracy. Make it .001 and try. If it works let me know.

[@sonuKumaryadav-ld7qz]

@@CADxTraining how can I change accuracy can you tell me please

[@CADxTraining]

I have already posted a video on KZbin. Search for that.

[@sonuKumaryadav-ld7qz]

@@CADxTraining ok sir

[@ajayn4480]

How could u mention M52 IN DRAWING and how could u show section 2 in drawing sir

[@CADxTraining]

Watch this to know more. kzbin.info/www/bejne/e2KufpiBg7OYg9E

[@ajayn4480]

@@CADxTraining sir one more doubt I saw almost all your sheetmetal videos. By viewing that I understand that two methods to make quilt one by making traingle extruded part and then using quilt form another one using revolve option and then quilt . While using quilt on revolve surface a deformation arrows are strangely located somewhere .I'm able to make quilt form How could correct that sir

[@CADxTraining]

I didn't get your question.

[@ajayn4480]

@@CADxTraining sir while using quilt form surface selected and mentioned with colour green but flip arrows are located somewhere on the object

[@piyushpritam2567]

How to do give dimention manually?

[@CADxTraining]

Look for dimension option. Or just right click and select the dimension option.

[@jamsteven9726]

How can you put the pic on Model Tree? Thanks!

[@CADxTraining]

It's done by video editor. Not part of Creo.

[@jamsteven9726]

@@CADxTraining OK! got you, thanks so much!

[@muniraj5395]

@@CADxTraining how could you please explain that

[@user-rc5fy8nc5m]

I failed in the feature of boundary blend

[@CADxTraining]

Change the file accuracy and try

[@user-rc5fy8nc5m]

​@@CADxTraining control point ， I used a broken point in the second sketch of direction 1. Successfully use the geometric points created in the sketch

[@adityagodase1485]

hello sir,boundary blend feature fails after giving control points.

[@CADxTraining]

Increase the file accuracy and try

[@adityagodase1485]

@@CADxTraining by taking two control points it is working, but is it correct ?

[@CADxTraining]

Modified the third control point according to the surface formed. After that you can select that point.

[@adityagodase1485]

@@CADxTraining how to modify ?

[@CADxTraining]

Share your part to me. I will check. Which version of Creo parametric are you using? [e-mail]

[@Rajesh360]

plz upload creo video more

[@sanjaynatarajan4906]

you just read out the way you are doing, but you have to explain how the methodologies works!

[@nikhilverma2796]

How to solidify it

[@CADxTraining]

Watch the video at 21:50

[@MSV7]

I haven't create boundary blend. Why?

[@CADxTraining]

You are asking yourself.

[@MSV7]

@@CADxTraining how create boundary blend. I am many times try but not able to create hook.

[@CADxTraining]

What is the problem you are facing.

[@MSV7]

@@CADxTraining I am follow your show in video 1st direction created but 2nd direction not created.

[@MSV7]

@@CADxTraining kindly give me a your mail ID, I will attach my drawing.

[@denvalatkinson4617]

this doesn’t even work

[@CADxTraining]

Change the part accuracy. Make it .001 and try. If it works let me know.

[@xxhimanshubakshixx]

@@CADxTraining not working