How To Change Crankshaft Seal On BMW N42 N43 N46 N52 N54 N55

[@mini_special]

I like that you use the proper tools

[@93jsaw]

I reaplced the timing chain on my N43 a few moths ago. I just hammered the seal in with a rubber mallet, and yes it's leaking.... Thanks for the informative video i will have to re-visit it now with the correct tool.

[@MrNicoe36cabrio]

Very nice DIY guys. Thanks for sharing! Dutch regards, Nico.

[@joehernandez6260]

I’m glad coming across your video best out of all I’ve seen job well done ❤

[@Magic4599]

I've been dealing with these oil leaks for about 35,000 miles, when I suspect the oil filter housing leak broke the serpentine belt. There's 150,000 miles on this N52 now. I replaced the oil filter housing gasket. I first did the oil pan gasket, thinking the leak was coming from there. I found some belt like material in the pan. Thanks to the e90 videos I now have the crankshaft pulley off. The seal seems good. I started the engine for a few minutes and it didn't leak. Now what ? On further inspection, and watching your video some more, I think the seal is toast. And it doesn't leak oil because the front end only is jacked up. Right, if "we don't get the seal out on the first try" the bolts need to come out of the special tool, to turn it and create new holes with the little screws, angling the screws to catch some of the meat of the seal. And so it went, success, no leaks.

[@bcuzofyuri9716]

this has been very helpful 🔥

[@petar443]

Браво. Доколкото съм запознат РТВ силикон става и за уплътнение и на картера, но май трябва да се изчака определено време след нанасяне за да "стегне" малко силикона и след това монтиране. 👍

[@crank3646]

Да то винаги е така с тези силикони . Даже в масовия случай , за да съм сигурен че е стегнал на 100% чакаме по 1 вечер преди да запалим мотора

[@3DxPOD]

Very interesting! Thanks for the info!

[@crank3646]

I'm sure you will use this information as needed

[@menne36]

Thanks for the vid bud

[@Hot80s]

your video is Beast thank you

[@George10s]

wow this was fantastic thank you

[@ParedesAutoServices]

excellent, good video. thank you.

[@robertmobileman8304]

Hi man good video , well explained , good job Rob mobile man

[@crank3646]

Thanks Robert !

[@robertoribera3801]

We’re did you get that tool is there a part number and how much Ty

[@alejandroarredondo1997]

I hit my crankshaft with the screws. How do I repair my nicked crankshaft? Any ideas?

[@getpaid38able]

Great video Wil this work on the V8 N62 06 BMW 750i

[@huanweili7699]

You helped me alot. Thank-you so much. 😊

[@filibertoleyva5312]

Very good video.

[@bryanderksen4448]

Good job! I was wondering what caused the damage to the tensioner puller. There are chips out of it

[@varspecllc]

Great video

[@vjs3771]

Thanks for the vidéo !

[@DorianBudana]

Very good information Thanks

[@stephenpedlow6762]

how do you change the N47?

[@postitandwatchit1434]

Good job I like the video Thanks.

[@traqnsavov822]

обтяжната ролка, някоя мишка я е гризала :)))

[@Lucky22noel]

Which tool is it

[@IvanRamirez-fs3sf]

Great video very detailed The rtv has to be applied on the notches only? Again Thank you very much for the information you share with all of us

[@crank3646]

Yes only there

[@simplelangperorock]

magnifico! fantastico!

[@chanchan1167]

Thank you

[@knightrida6829]

Thanks

[@gari4kata]

Много интересно Crank това за бензиновите мотори се отнася нали?Кое е тех.име на заменената част на денфера (гарнитурка)

[@crank3646]

Мерси Павел ! Семеринг колянов вал ( преден )

[@DG-od4si]

[@stoqnesko]

The part with the electric ratchet was a bit too professional :D Otherwise, great video!!

[@crank3646]

I knew it :D

[@Mupek]

Хелоу вювърс :)))

[@crank3646]

Hola muchacho

[@Nalopotato]

*This video was brought to you by: Gargling Olive Oil*

[@94tontonche]

Activ translate please.

[@TOBLEROWAN123]

Just done this by hand on an m57 was a nightmare

[@crank3646]

M57 is much more easier, than the newer BMW petrol engines. But still I have made my own installation tool for the diesel ones

[@noobishsite]

should use hot water on the plastic

[@PartiBuoy]

Tool snaappped broken

[@drisslekhal7359]

Thank you

[@Lawgive1234]

Thank you