It's amazing how cheap 3D printers have improved in value and speed recently, double Z, direct drive, networking, very good bed leveling and hi speed for 200.
@_DROM_9 ай бұрын
I'm new to your channel and I must say... It's impressive the amount of useful and straight to the point info you pass in a 25 minute video reviewing a printer. The comparisons to Prusa and Bambu were the cherry on top. Can't wait for your review on the KE (the one I really want from Creality)
@lyndonfoster109011 ай бұрын
Wonderful as always. One of these days if you run out of ideas to review , reviewing 3d printing accessories like air purifiers, filament driers or whatever useful accessories you have found useful would be great. I really appreciate all your efforts and you are making a difference in the 3d hobby world for sure.
@Liberty4Ever11 ай бұрын
Creality engineers worked hard to get to that $199 MSRP with most of the modern features we want. They did a great job of eliminating cost and complexity (no bed leveling knobs) without adversely impacting the capabilities. As expensive as cable is, I wish manufacturers would switch to a 4 conductor continuous flex rated cable to the extruder instead of a large ribbon cable. CANbus or some similar serial interface could be used and still be less expensive than ribbon cable and connectors. This would allow the cabling to stay the same for new printers as features are added such as LEDs on the print head, an optical filament runout sensor (mere pennies) at the top of the extruder where it's completely painless, etc.
@ipdjbt11 ай бұрын
lol
@floodo111 ай бұрын
Wow, wish my original Ender3 was this good back when I first got it a few years ago hehe
@teitgenengineering11 ай бұрын
Me too!
@teitgenengineering11 ай бұрын
I had to spend and extra $100 to get my ender to even print anything
@d.jensen515311 ай бұрын
@@teitgenengineering I can't relate. Except for filament and electricity, I haven't spent an extra dime on my original Ender 3. It still does an outstanding job.
@teitgenengineering11 ай бұрын
@@d.jensen5153 ya I don't no what it is I sent my first one back thinking it was defective but the extuder on the second one grinned to I just got fed up with trying to get it to work and put an h2 on it and got a pei bed
@kenspaceman393810 ай бұрын
This is one of the most methodical and well thought through review I’ve seen on this specific printer. I’ve got two Ender 3 v1 and already ordered one 3 v3 se set for evaluation. Might replace the old ones.
@wholebuncha18449 ай бұрын
Only 2 minutes in and you've already given me more interesting details than like an hour of other reviews I've seen today. Good stuff!
@3DandTeePrinting11 ай бұрын
Great Review. It's not rated for it but I had great success printing abs in an enclosure with it also. I Love this Machine. Got mine on the 9th of August and has been printing Great. Only issue was the 1 of 2 cover hold down screws above the y-axis linear rail was clipping when printing. Replaced with a flush screw problem solved. Already racked up 200 hours on her and still going well.
@camerageek110 ай бұрын
Excellent review with a combination of qualitative and quantitative print samples. Made it clear that this printer would meet most of my printing needs at the price I am willing to pay. I considered the K1 and Bambu P1P, but this printer will suffice for 99% of my printing needs. Keep up the excellent work!
@banny123456Ай бұрын
Still happy with your purchase? Becase i almost threw mine out of the window. Few weeks ago buy a another printer, bambu a1 mini and ender is trash compared to bambu. I don't have one nice and error free print on ender.
@hrdcpy11 ай бұрын
The evolution of the Ender 3 is pretty amazing.
@banny123456Ай бұрын
I buy one and it's trash. Then for almost same money I switch for bambu and it's night and day. Ender 3, ever "best" SE version is un-usable.
@fupersly7 ай бұрын
Love your reviews. Amazing job. I would suggest using not only the same filament brand but the same color for some of the tests of the same model. That would remove a variable in the testing output.
@robosilo11 ай бұрын
Great review! I hope to see precision ground linear bearings on more budget machines and more of the axes. They should have a much longer service life and are very easy to source parts for.
@theodoreolson85298 ай бұрын
Thanks for your video. I'm an older retired guy looking to 3D printing as a hobby (as well as supporting my other hobbies). I have to say your review video has been superior to others I have seen. Well done.
@Fred_le_lorrain11 ай бұрын
Your video is clear and precise, without unnecessary embellishment. The printed designs are varied and your speech is perfect even for a fluent non-English speaker like me. The close-ups are very detailed and we can clearly see the qualities and defects of the print. Thanks.
@railsonsilva59638 ай бұрын
Pesquisando sobre essa impressora aqui no brasil ainda não tem analises dela, então resolvi olhar para a lingua inglesa, e achei seu vídeo, não sei falar inglês então tera que traduzir kkkk eu amei seu conteudo as comparações demonstrações tudo incrível ganhou um seguidor brasileiro.
@DennisMurphey11 ай бұрын
Always thorough and thoughtful review looks like a $200 winner lots function that deliver a good part. I have a lot of functional train parts where this little guy could be a great production unit. Thank You for sharing this fine review, you guys do a great job, Dennis
@craquipiso11 ай бұрын
I rarely comment on reviews... actually, I have never commented. However your content has been the most informative and organized video I have ever seen. Your opinions are practical, and your assessment of features is very insightful. Thank you.
@pspicerwensley10 ай бұрын
I just bought a SunLu 3D Print pen the SL-300 Plus I will be using it to fix prints and add detail on 3D printed items. SunLu has the best pens. I also bought a spool of PCL that melts at a crazy low temperature for my grandkids to design using the pen. Thank you to SunLu for sponsoring the channel. ❤
@trance_trousers11 ай бұрын
The best review of the Ender 3 V3 SE I've seen to date! I have one due to be delivered in the next couple of hours 🙂. It'll be my second 3D printer, alongside my upgraded Ender 2 Pro. I also had an original Ender 3 (my first ever 3D printer) which I modified and upgraded the heck out of, but sold a few months ago. The Ender 3 V3 SE is a considerable improvement on the original Ender 3!
@Travix0311 ай бұрын
Thank you for starting to incorporate the first layer sheet test, please show this on all future reviews!
@hagaybar9 ай бұрын
Excellent review, I would appreciate it if you could guide us and prepare a video tutorial on how to upgrade the filament detection sensor and the hotend pei sheet, and also links to the appropriate parts because it's not the most clear to all of us thanks
@aklstreak7 ай бұрын
So far this is the best video about the Ender-3 V3SE I have seen. Very informative with excellent examples. Thank you!
@truszko916 ай бұрын
I bought it last week. It's been AMAZING so far as my first printer. I had to slightly adjust Z offset manually just a bit when auto level didn't get it perfectly, but that's fine/
@heribertoponce855311 ай бұрын
This girl knows how a review should be done. Thank you.
@HyroDaily10 ай бұрын
I'll have to check out that recycle plastic, most of my stuff is pretty simple.
@bluewolf49158 ай бұрын
Mine arrived today. I'll dig into it tomorrow. This is brand new to me.
@marce29028011 ай бұрын
I was waiting for this analysis, I wanted to give my older sister her first printer, something modest this could be a good option
@thorntontarr289411 ай бұрын
Another outstanding review and input to Creality and us. Aurora Tech has become the "Consumer Reports" of 3D printers. Well done. Amazing performance for $200 delivered by Creality. Based on the AnkerMake M5C removal of the display and use of one's smart phone, it seems likely that your suggested additions of a filament run-out sensor and upgraded nozzle could be added without increased cost and maybe even a cost reduction
@cameltoast11 ай бұрын
Really is making the best, most thorough reviews while these other people are trying to be funny with corny jokes.
@Gamboa969 ай бұрын
I bought this printer because of this video and it was a awsome choice. Ive been very happy with it, comming from a ender 3 clone printer, this one is a beast!!!!! Thank you
@natebayne8 ай бұрын
I’ll have mine late Jan 2024…. Can’t wait to dive in
@DS321o11 ай бұрын
Out of the box with a probe + dual z for $200! Great deal. I think I paid $100 for those two things alone lol
@wfpelletier434811 ай бұрын
Thank you for another great review. This looks like a very good machine for the price, but the only other 'con' thatI see is that it still has a PTFE tube in the extruder/hotend. Perhaps since this printer is designed for beginners, Creality thought it was better to have the printer designed for lower temperature filaments. Do you think it would be easy to fit an all-metal heat break to this hotend?
@rich979211 ай бұрын
Great as always. You helped me decide on K1 Max. Hopefully they’ve fixed some of the things you pointed out that need to addressed. Waiting for its arrival!!! Keep up the great work!!!
@jonathanberry11113 ай бұрын
Your comment has made me conclude I'm probably right getting the Bambu A1... now it doesn't burn houses down.
@user-vi2gp5xw1e10 ай бұрын
i was able to put a filament sensor on the v3 it was not easy to do and took about an hour to do had to make custom brackets for it and had to hard wire it directly to the motherboard 150 prints later still works prefect and yes the filament sensor works great
@Jestunes11 ай бұрын
Stellar review as always. Would love to see an outro or intro with you doing an Aurora Tech dance routine. Even involving your brother. Your smile and laugh always made my day. Like this new Creality printer. Good value.. PS loved your chose of background music.
@CRAZYBUILD3499 ай бұрын
outstanding review, thank you, great job, and i will be ordering one soon,
@bluerider098811 ай бұрын
Another great Review. The best on KZbin imo. Any chance you'd be able to review some higher priced printers to compare to the normal hobby printers? I'm interested in the Pantheon HS3 in particular. I'd also like to see you maybe incorporate some sort of accuracy test for these printers, not just the clearance test, but printing an actual part and measuring it to see how accurate the finished parts are Keep them coming. Thanks.
@AuroraTech11 ай бұрын
If they're willing to send me one, I'd be happy to review that machine. I'll also consider adding accuracy tests in the future.
@rapalma3811 ай бұрын
As a user of the Ender 3 pro, with all mods possible, this model at this price is very cheap, and capable to print any material.
@kenspaceman393810 ай бұрын
I wish this channel would test also the Ender 3 v3 KE and compare print speed and quality with the SE, side by side.
@idmnstr11 ай бұрын
Thank you for this video. I just saw the Creality product launch. I have looking forward to your review of the Ender 3 V3 and V3 Plus. These were shown along with this SE and the KE. If possible a comparison of the Ender 3 V3 and the Neptune 4 Pro would be ideal.
@fredblogs11 ай бұрын
Makes my S1 look old fashioned. Brilliant review. 👍👍👍👍👍
@Smokinjoewhite11 ай бұрын
The 27 minute benchy they gave you looks like it's .25 layers too.
@davidcasler891310 ай бұрын
This was a PERFECT review! Great video. I just received my V3 SE and the z-offset is not accurate like yours so it is attempting to print too high. With the included model on the SD card. I'll try to manually compensate and see how it goes. A little disappointing being that the z-offset should be automatic.
@LutherBuilds7 ай бұрын
Those are some great results from the printer. Mine is set to be delivered today.
@davidboop355011 ай бұрын
I was about to be super poo poo on this printer and say it doesn't do this and it doesn't do that. But I took a step back. This is $200 and this is kind of everything you need for a beginner and I'm not a beginner. This printer wasn't meant for me, I completely agree with you about the filament run out sensor and if this printer is geared for beginners rookies will make that mistake. I've done that twice, when I first started. I just wish it went to 300° on the hot end but now that I have printed for as long as I have, only 3 years though, plus 260 isn't really needed on an open frame printer in my opinion, but there are so many enclosure solutions now that are cheap. That's why I'm a stickler for the 300. Epic review.
@billcs6611 ай бұрын
If you get a ender 5 PEI sheet it fits and makes the printer even better. My opinion. Thank you for all your hard work.
@bikepacker98502 ай бұрын
Great unbiased, factual review. Thank you...
@akashic88811 ай бұрын
Really hoping creality would release an allmetal hotend upgrade for this printer in order to print ABS and ASA without any worries
@user-jr2re8pz8m8 ай бұрын
Please make a video about the Creality Ender 3 V3 KE
@TheReelport7 ай бұрын
I just bought it, super simple setup and prints were pretty good with PLA. Weird move from Creality is bot to include the Vibration Sensor in the package, with that it would be a winner against the A1 I guess. But I am just a noob, so 😅 Or they want you to stay as a "modder", i think i will keep this
@Dirt33breaks11 ай бұрын
That first layer sheet @40mm is amazing!!
@BariumCobaltNitrog3n11 ай бұрын
I like how the little sensor pops out like a pinkie testing the temperature of the tea. So dignified. I love your reviews, do you have any recommendations for buying used printers, refurbished, out of box, demo model kind of thing?
@AuroraTech11 ай бұрын
Just search on eBay; there are quite a lot of used/refurbished machines at super low prices. As long as you can fix some minor issues, they are a pretty good deal.
@BariumCobaltNitrog3n11 ай бұрын
@@AuroraTech Thanks. I'm not in a hurry so I'm trying to draw from the wisdom of people like you. 🧐 Are you bridge and tunnel Danville?
@Gamer317.9 ай бұрын
Hi, im hopefully getting this for chrismas! This would be my first printer. Cant wait.
@TheCommanderCain11 ай бұрын
That's a lot of Nice to haves for $199... Love watching your stuff its soo well done
@fernandoandradesanchez71227 ай бұрын
La mejor descripción de producto, felicitaciones y gracias. ¿Podrían explicar cómo conectar la impresora al wifi? MUCHAS GRACIAS abrazos desde Colombia.
@sinetwo11 ай бұрын
Got one recently delivered. Gonna set it up tomorrow. Great review! I do wish it was possible to get a better and smaller network module
@CuttinInIdaho11 ай бұрын
If I level my V2 Neo every print at the printing temperature for my material, and set the Z offset every print, I get almost invisible layer lines. The magic of Creality is this. The Voodoo side is that I must level and set Z every print...even if I don't change material... I want this. Faster, fairly clean, and clean looking.
@Rave-agent8 ай бұрын
This is how you present a review video. Thank you.
@evlogiy2 ай бұрын
This is my first time on your channel, and I must say, the contrast is striking. You have the voice of a 30-year-old American female voice actress, yet you appear as a 12-year-old Asian girl. That's mind-boggling. 😂
@sboeke9111 ай бұрын
Excellent review. Seriously. Very in depth and exactly what I was looking for.
@stephan.scharf11 ай бұрын
Todaaaaaaaaaaaaaaaay another professional review from Lung-team.
@UserUser-hc6go7 ай бұрын
Даже слабое знание английского позволяет понять смысл. Отличное изложение. Отличное произношение. Продолжай.
@leonardoinhoqui4 ай бұрын
I have 2 printers 3v3 se, both of which have a lot of resonances, it makes a very dragging sound when there is a prominent location on a wall, I am using orca slice standard profile from 3v3se
@jasonwu275811 ай бұрын
Creality has the legacy and brand recognition to do it. With that new Kobra 2 Pro out it so hard to decide which pros and cons you can accept. Roller bearings on the X axis, and with the backing of the Creality community this would be a budget beast if there was input shaping from the get-go. With Bambu Lab starting the next gen trend of 3D printing, I do wish to see a bedslinger I can still say I would purchase today. My 1st printer was the Aquila X2 which is pretty much the Ender 3 V2. Now I got a P1S+AMS Combo I'm content. Though I do miss tinkering so I'm waiting for that affordable bedslinger that will give my P1S a run for its money. Great work as always! The 3D printing princess and should be up there with the likes of Melissa Wu and the like.
@ThantiK11 ай бұрын
None of Anycubic's FDM printers are good. Avoid them at all costs. I run a repair shop and the Anycubic machines have electrical and quality issues like you wouldn't believe.
@jasonwu275811 ай бұрын
@@ThantiK I've own in chronological order Aquila X2, Flsun SR, Kobra, Ender 2 Pro and P1S+AMS Combo. Never had an issue with any of them. I believe user error probably amounts to a lot of the issues.
@MrBaskins201011 ай бұрын
Any news on this new CR-10 with klipper and linear rails? I read about it somewhere but forgot to screenshot it. Glad creality is waking up to changes in the space overall, seems like they’re listening to your feedback
@AuroraTech11 ай бұрын
Yes, they are sending me the CR-10 SE and I will try to fit it in my overloaded schedule.
@josephmama965711 ай бұрын
WOW!! $199!? thats fire.
@salroth42011 ай бұрын
Great video! I have been waiting for an in-depth review of this printer.
@tasso61969 ай бұрын
What a great review. I was looking for a second printer and decided to buy this one after watching. tks
@CpatDaRAT11 ай бұрын
I've been wanting to get into 3d printing this looks like a good candidate
@LordDarthNihilus11 ай бұрын
Your reviews are awesome and by far the best I've seen in KZbin. All information but in short time explainined. I've come to your channel by searching for reviews about the OMG extruder and I'm glad I did, because watching your videos is simply amazing for gaining knowledge about new hardware!
@TheZombieSaints11 ай бұрын
Excellent review of this printer, creality should be very happy with that. Seems like a decent printer for that price. Good stuff 👍
@awesomearizona-dino11 ай бұрын
Thanks Aurora. great work as usual.
@yotam6x711 ай бұрын
Maybe this could be the new lineup beyond the V3 SE Ender 3 v3 S1 - PEI sheet, all metal hotend, filament sensor, better cooling, Wi-Fi Ender 3 v3 S1 Pro - same as previous, mainboard upgrade for Klipper
@theglowcloud221511 ай бұрын
It's the "how many times can Creality remake the same printer?" game :D
@AuroraTech11 ай бұрын
As long as they can make it cheaper and with more features, I don't mind seeing an Ender-3 V100 in the future.
@theglowcloud221511 ай бұрын
@@AuroraTech true, this is an improvement over the original Ender 3. Bed slingers have a lot of life left in them as long as quality of life elements like part cooling and firmware continue to improve. I'd be thrilled to see V-wheel rollers go away forever, though :D
@trsfc159510 ай бұрын
Looking forward to your cr10 se review
@vlozity11 ай бұрын
would be nice if you can make a video on what parts to upgrade and how to go about it
@MozDivision9 ай бұрын
For a beginner, would this be the recommended entry level printer now? Or the Sovol SV06? Print size and speed not being an issue. Mostly concerned with precision for functional prints
@ArtplusHrApps11 ай бұрын
I was just thinking abut getting Anycubic Kobra 2... as a cheap upgrade to old (barely used) E3 Pro... and now... Dunno again... :)
@TripleFX11 ай бұрын
Very thorough review. Thank you.
@gianlucatoni47119 ай бұрын
I bought it, thanks for everything, keep it up
@bclp526 ай бұрын
Can you all do a review on the KE
@JKC4011 ай бұрын
the twinkling pla looks neat. i bet you could print some nice minifigs or something like that with it. i wonder how this machine would perform when hooked up to a sonic pad
@jojojogonzalez11 ай бұрын
You are so chill til you get to the cons lmfao awesome vid
@yeroca11 ай бұрын
Very nice review! It seems this printer is kind of an S1 killer. Maybe there will be an S2 with these upgrades, especially the improved cooling fans. Isn't the print temperature of ABS close to the temperature of melting the PTFE tube?
@AuroraTech11 ай бұрын
Yes, that's why the Ender-3 S1 is on sale for $246. A good quality PTFE tube can resist temperatures up to 270°C, but I don't print ABS often, except for testing printers, so I haven't had any issues with that.
@yeroca11 ай бұрын
@@AuroraTech Interesting, makes sense. I guess they will phase out the S series. Somehow I was thinking PTFE started breaking down at 250°C.
@agmuntianu11 ай бұрын
nothing above 240 is recommended : "DuPont studies show that the Teflon offgases toxic particulates at 464°F." ( 240C )
@NeonDreams77 ай бұрын
This is a great video! Thanks
@phuntshotobgay75519 ай бұрын
So informative and clean review 🙂
@corstafine8 ай бұрын
@Aurora Tech. I'm just about to get this today, if I bought it through your link do you get some sort of percentage/cut etc? If so, that's what I'll do....Best review I've seen yet on here. Fingers crossed for a reply before I buy
@clintwestwood189511 ай бұрын
Cool review video, 199$ is awesome
@3dtechnologies15311 ай бұрын
You go girl! Great review!
@goodash111 ай бұрын
Very comprehensive. Thank you.
@mikehunt74198 ай бұрын
Well presented, thank you 👏🏻
@rondlh2011 ай бұрын
This looks like a fantastic beginners printer
@jasonmarquette11 ай бұрын
Another great review!
@abhishekbisawa688311 ай бұрын
Very good review. Please review of Elegoo Neptune 4 / 4 Pro and compare it with V3 SE.
@bxkxhxkg8211 ай бұрын
With some input shape tests and klipper this migh be able to achieve 150mm/s constantly without drawbacks
@Blazs120gl11 ай бұрын
Hi, I'm totally lost in the different offerings of Creality (and competitors) 500 USD printers. What I'm looking for is a printer that can just print after an initial setup. I would not tinker it all day nor look for mods, but just print with the best quality and resolution possible. Speed is no factor but building area is key, the higher the better. I was recommended the Ender-3 but I wasn't told the exact model. Based in my research the Ender-7 was attratcive, but it seems like it's sub-par on quality. Now I'm looking at the Ender-3 S1 Plus, but also the S1 Pro has some features I can't tell if I need (and less building area). I'd use it for longer prints, 1..2 per week for small series product printing. Always the same choice of (PLA?) filament. Any ideas are welcome! Cheers :D
@RB-yq7qv11 ай бұрын
Another great review.
@N1RKW11 ай бұрын
That is a lot of printer for not a lot of money! The pros seem quite good, and the cons pretty minimal.
@serdalo503511 ай бұрын
Hello Aurora! Love your channel! Will you be looking at the Kingroon KLP1? Its a Klipper based CoreXY.
@Edward3DFX6 ай бұрын
Epic little machine
@nikikefalas10 ай бұрын
Hey Aurora! I purchased one based on this awesome review. I am also getting that weird noise fan at 127 . Did you hear back from Creality?