CReeves Makes the Mobile Router Table Combo with Kreg Features ep0028

Plans for this build: www.buildsomething.com/plans/...
For this build, I knew that wanted to fit two tools into a relatively small footprint. Having a small shop that shares its space with vehicles, I needed it to be mobile as well. The icing on the cake was the addition of a full dust collection plumbing system complete with blast gates.
I would like to thank Kreg Tools and Purebond for sponsoring this video and providing some awesome tools and products that I can implement into this table.
There will be plans up the www.BuildSomething.com website for this build. Please keep in mind that plywood and material thicknesses vary and there are some dimensions on this project that can be "off" due to that.
I JUST GOT MY WEBSITE UP AND PLANS ARE NOW AVAILABLE HERE: creevesmakes.com
As I keep growing and going, I will develop and add more plans to the site! Please comment or contact me and let me know what plans you want to see next! Thank you to everyone for the support! Without you and this community, I wouldn't be able to host and put up this content the way that I do. I hope to make this a more common occurrence in 2019! Thanks!
Tools used in this video! Thank you for supporting me and what I do!
Kreg Foreman: amzn.to/2GaOu2s
Kreg Precision Router Lift: amzn.to/2D98FtH
Kreg On/Off Switch: amzn.to/2MOFIYv
Kreg Router Setup Bars: amzn.to/2tE2UQi
Kreg Router Lift: amzn.to/2BQmkpG
Kreg Router Fence: amzn.to/2ExkNGR
Kreg Feather Boards 2x: amzn.to/2IBsQpV
Kreg K4: amzn.to/2HdUapY
Kreg Face Clamps: amzn.to/2IwYTTc
Kreg Right Angle Clamp: amzn.to/2IxUyis
Kreg Automaxx Face Clamp: amzn.to/2Eq5Kev
Kreg Automaxx Bench Clamp: amzn.to/2GJt8pC
Kreg Automaxx Face Clamp 6” : amzn.to/2IwPMSl
Kreg Automaxx Vise: amzn.to/2IzTLOd
Kreg Mini Trak: amzn.to/2IuSZC8
Kreg Accu-Cut: amzn.to/2uMdnwg
Kreg Top Trak: amzn.to/2IuugOf
Kreg Universal Clamp Trak: amzn.to/2JnzMn6
Kreg Swing Stop: amzn.to/2Iyo0VM
Kreg T-Track Clamp: amzn.to/2HefewF
Kreg LtR Tape: amzn.to/2H0fCkO
Kreg Jig and Fixture Bar: amzn.to/2GFziLd
Kreg Production Stop: amzn.to/2IwNnHk
Kreg Multi-Mark: amzn.to/2Jrfqt1
Kreg Drawer Slide Jig: amzn.to/2GV2TzR
Kreg Cabinet Hardware Jig: amzn.to/2q8Hidg
Milwaukee Bit Set: amzn.to/2EpORkg
Microjig GRR-Ripper: amzn.to/2uPAm9P
Microjig Leg Set: amzn.to/2H3FCvA
Rockler Glue Brush: amzn.to/2q9WgA2
Rockler 2-1/2" Blast Gates: amzn.to/2DSuBKW
RZ Mask: amzn.to/2EpZwv6
RZ Filters: amzn.to/2qaWwPc
Casters: amzn.to/2LX9KaH
15' corded Power Strip: amzn.to/2t4MobC
18" Drawer Slides: amzn.to/2Grf2Mh
Resources: ======================================================
Kreg Tool: www.kregtool.com/
Fix This Build That Drawer video: www.youtube.com/watch?v=Ilda2...
Social Life: ======================================================
Be sure to Like, Subscribe, and Follow me on the following social media platforms as well!
Facebook - creevesmakes
Instagram - creevesmakes
Twitter - creevesmakes
Music: ======================================================
"Type Your Name Here" by Jahzzar
Licensed under Attribution-ShareAlike 3.0 International License.
AmpleTunes: ampletunes.com/

[@CReevesMakes]

PLANS ARE LIVE ON WWW.BUILDSOMETHING>COM www.buildsomething.com/plans/PD6AE6BE9202FBB25/Mobile-Router-Table-Combo-Foreman

[@sconrady123]

It would probably sell for 800 cabinet easy

[@mpe777]

That is a mean looking workstation. It got my creative juices flowing. I don't have a tabletop router like that one but I have the Skil SRT1039 bench top so I'd have to see how I would get mine to fit those planes unless I can detach the tabletop piece and mount on the cabinet. Great job sir!!! Also, YES, I would have painted to dust collection pipes also. Black or blue.

[@CReevesMakes]

This one is for sale!

[@ronalves9118]

I see you are an Orange and Blue shop!! That is a beautiful cabinet. Thank you

[@CReevesMakes]

Yep! Good colors! Thanks for watching!

[@snipderdon]

Man, why did this video not come up when I was building my table? This is brilliant. Thanks for sharing!!

[@jaybrunn1175]

I've been watching a few of your videos, and so far I must say I enjoy the functionality and overall design of your shop and builds... thanks for all the helpful information. Jay.

[@CReevesMakes]

Thanks Jay I really appreciate it! You’re very welcome and thanks for watching!

[@davidshaw5126]

Now if watched this build twice, amazing job Kreg stuff looks good. Slowly starting my collection.

[@CReevesMakes]

Thank you!

[@RISENGRINDWORKSHOP]

Recently just added the Kreg Forman to my small shop. Will need to create something similar. Thanks for sharing appreciate it the video!

[@CReevesMakes]

Congratulations on the new toy and thank you very much! Good luck and have fun!

[@AngieWilliamsDesigns]

This is a great build. I love how it turned out. And yeah... painting all the dust collection black was a good call. That was a good call. Looks better. I have the Kreg router table so I don't see me making this particular set up... but I really like this. I learned from the build and it gave me ideas on what to do when I enclose... and trick out... my Kreg table. Thanks for sharing.

[@CReevesMakes]

Thank you very much! Im glad you got something from it!

[@lVl1GGL3]

Hell of a build! Painting the dust collection pipes was a good choice. I might have to buy the plans as I'm quickly running out of room in my tiny shop. Great video!

[@CReevesMakes]

Thanks a lot Mike! The plans are FREE! Get buildin buddy! 👍🏻👍🏻

[@zetham7333]

Nice build! As you were assembling the pvc for the dust collection, I was thinking “I would have painted it black”. And then that is exactly what you did! This is definitely going on my list of projects I need to do this year. Thank you for your videos.

[@CReevesMakes]

Thanks! I am very happy with the painted look. Much cleaner. Good luck!

[@MauricioLopez-xb7oe]

SICKK ASS JOB.. 39 People are hating that they can't build this masterpiece

[@TheTranq]

Yes spraypainting it black made it look much cleaner. Great build!

[@CReevesMakes]

Thank you!

[@CReevesMakes]

Thank you!

[@thejoshthat]

Mind blowing! I love how the side shape minimizes floor coverage but is secretly providing allowance for tubing without jeopardizing comfort for the user! Genius! I'm half way thru a build like this now but it's nothing to bring it in a bit! Thank you so much! I'm so happy I caught this build in time!

[@CReevesMakes]

Awesome! Thank you for the comment. My goal was to provide the most effective work system with a small footprint and it has proven itself every time that I use it! Just used it last night and still LOVE IT! thanks and good luck to you!!

[@glennboniface]

Beautiful job Casey, as always.

[@CReevesMakes]

Thank you very much Glenn! 👍🏻

[@jeavideo]

Great build! Thanks for the details - especially on dust collection!

[@CReevesMakes]

Thank you very much! The dust collection was my favorite part!

[@MacnWood]

awesome build!!! I'm in the need for something just like this. I love how the grain continues and flows across everything!!!

[@CReevesMakes]

Thank you MNW! Plans will be up soon I hope. The grain was a challenge with the cut list but it worked!

[@davidshaw5126]

That’s looks great, starting my wife out with her own shop I’m always looking for great ideas. Thanks.

[@CReevesMakes]

Awesome! Thanks!👏🏻

[@jlf1430]

Excellent project, really looks user friendly and will last you a long time. Thanks for sharing..

[@CReevesMakes]

Thank you J LF! Yes it is very fun and easy to use. Thank you for watching!

[@FranksDIY]

That was an amazing build my Freind. I loved it it . I also kept seing how you made your work bench and You got me thing of re doing mine.

[@CReevesMakes]

Thank you very much Frank!

[@RevivedBuilds]

Casey, great job man. This makes me want to redo my router table. Great job!

[@AGlimpseInside]

Pretty awesome project brother. I agree with the choice of using glue. It’s just adds the rigidity needed for a project of this size. Again, nice work

[@CReevesMakes]

Thanks Chris! Yeah I glue a LOT of stuff. Haven’t had to take anything apart yet knock on wood! 👍🏻🤞🏻

[@JohnBuildsIt]

Another great build Casey! Killed it!

[@CReevesMakes]

Thank you very much John! I appreciate that!

[@daveyJ213]

Awesome work, sir! Professional fit and finish in my opinion. I am planning on designing and building a small (8 ft.) work bench for my miter saw. Your video gave my many great idea. Yes, painting the piping made it look meaner and leaner. Very nice!

[@CReevesMakes]

Thanks!

[@billybike57]

Painting the white PVC pipe was a good decision 👍🏼

[@thetmyers3881]

a really nice project and the dust collection painted pvc was an excellent choice

[@CReevesMakes]

Thanks Trent! Yeah I am loving the way the piping looks.

[@stevecox552]

very cool,, you did a great job,,, you have inspired me to re-do a couple carts in my shop to make more room

[@CReevesMakes]

Oh awesome! I am glad that you got inspired to update some stuff! Good luck!

[@davidcole333]

I love this concept. I suggest adding a storage board to the base of your bit storage drawers, predrilled with 1/4 and 1/2 holes for the collets.

[@CReevesMakes]

I actually just did that using the Rockler inserts! Thanks for watching!

[@jdc5941]

Great job of explaining your process, I also like and use Kreg tools, an outstanding company, most products are USA made also.

[@CReevesMakes]

Thanks JD! I agree and love Kreg products. I will be doing a factor tour there this June! A LOT of their stuff is made in Iowa! 👍🏻👍🏻

[@hj8607]

Nice clean build .

[@SableSunsets]

I have never seen that great little rigid screw driver I need one !!!

[@CReevesMakes]

It is great! I love using it for assembling projects.

[@sumosprojects]

You’ve a fantastic workshop & an incredible video delivery style, top work 🍻👍👍👍👍

[@CReevesMakes]

Thank you very much Sumo! Its a non stop work in progress!

[@eyecandy-gaming]

The pipes look so much better black. Nice job

[@CReevesMakes]

I agree! So glad that I painted them! Thanks!

[@trueemail9687]

Wow very nice set up. Would love to have one. Looking over plans for a router table and I run across this. I hit the jackpot!

[@jeffforbes3772]

Very cool. Thanks for posting.

[@CReevesMakes]

Thank you Jeff!

[@IEnjoyCreatingVideos]

Nice job on the mobile router table Friend! Thanks for sharing the video with us.👍😎JP

[@CReevesMakes]

Thanks JP! Happy to share all of my builds with the community! I was inspired so hopefully I can pass it on! 👍🏻

[@IEnjoyCreatingVideos]

😎

[@rebecca5837]

Great Builds! Very inspiring!

[@CReevesMakes]

Thank you very much!

[@kevindavis51]

Looks awesome and very functional. Me personally, I would have used flush mount door/drawer hardware to reduce the risk of catching clothing on the pulls.

[@waynegnagey4126]

Great build. Very versatile

[@CReevesMakes]

Thank you very much! I use it more than I expected and it’s great! 👍🏻

[@hhanger1]

Norm started a revolution with his first router table. it has been copied, modified and improved too many times to count. This version is a top 5 for sure. Norm would be proud.

[@CReevesMakes]

Why thank you very much! I am honored to have such a nice comment on this table. Thanks! 👍🏻

[@jaomap]

love the tools you have and the skills

[@CReevesMakes]

Thank you very very much Jao!

[@fernandogonzalez4834]

Great job on it. I had to go with flip top table to fit more Equipment in my small shop...

[@CReevesMakes]

Thanks! Yeah, we all have our own unique needs in our spaces. I have a flip top as well and its perfect for what I need in that area.

[@stevennachlas9596]

This is a nice project and since I have the Kreg router table and the Foreman, I was contemplating doing such a project. So I’m glad you created the plans for it. The printed plans were a little confusing regarding adding the two horizontal dividers. Although I can pretty much extrapolate the distance, it would’ve been nice if the plans showed at what height you mounted the dividers. It also implies that the dividers were added before adding the top for the Foreman. But in the video, it looks like you added the Foreman top before adding the horizontal divider panels. That’s certainly the way I would do it as it gives you room to work. If you add the horizontal panels first it would be very difficult to get the top on using pocket screws. All in all, a really nice project. Thank you

[@WoodshopMike]

Great project and execution man. You build some awesome stuff!

[@CReevesMakes]

Thanks Mike! I build what I want/ need for my space and try to challenge myself with every build! Thanks for taggin along for the journey!

[@KennyB9871]

Man that is sick! Nice work!

[@CReevesMakes]

Thank you! It was a work in progress in my mind and then it slowly came together and turned out just as I had hoped!

[@43srgrock]

Awesome router station. Just watched it for the second time.

[@davidshaw5126]

WOW, I love what I already have of Kreg tools but dude do you have the hookup! Very nice!

[@CReevesMakes]

They sponsored this build and the free plans are on their website at www.buildsomething.com

[@lionelhernandez34]

Good looking project, great video

[@CReevesMakes]

Thank you very much! It was a challenging build and a lot of it was on the fly! It turned out better than I expected!

[@bradleverton3233]

Nice well thought out build.

[@CReevesMakes]

Thanks Brad! 👍🏻👊🏻

[@josecuervo4749]

Very nice design and build.....the only thing I'd do is add a blast gate to the router table fence so that if you are doing something where the fence is not providing actual suction, like for anything buried in the piece, you can concentrate the suction in the router chamber....oh, and drill some holes in the front of the router chamber door to provide bothe intake and router motor cooling.....thanks for the great content.

[@CReevesMakes]

Thanks Jose! That is a great tip for the fence! I actually left 1/8” gaps on the top of the front door for suction.

[@rodolfogagnotti5066]

Hola buena tarde , que lujo , un espectaculo muy bueno me encanta ver tan prolijo trabajo ... Mil felicitaciones y saludos desde Argentina ...

[@johnross9369]

Go Big or Go Home! Nice build as always.

[@r.m.2301]

Just found your video... Nice job good explanation will be watching for more videos thank you

[@CReevesMakes]

Thank you very much Ralph! I appreciate the support and comments!

[@thehangardesigns]

Ha! My TS3650 has the same "oops" mark! Great build!

[@CReevesMakes]

Right of passage it seems! LOL

[@traciethomas1910]

That looks awesome! Best one I've seen. Great job explaining everything too. I like the PVC painted black. I'm a new subscriber :)

[@CReevesMakes]

AWESOME! Thank you very much Tracie!

[@edvardschock9739]

Awesome build! Thanks for sharing. the pipes 100% look better painted, in the future you could try ABS instead of PVC

[@CReevesMakes]

Thank you and thanks for watching! I agree, the paint makes them look WAY better. I thought about using ABS as well but I had most of the PVC already and only needed a couple of elbows. Is ABS cheaper than PVC? Thanks!

[@steverusso5369]

came out great

[@CReevesMakes]

Thanks Steve!

[@matthewmills6452]

Time for a shop tour!

[@CReevesMakes]

When the weather gets nice! 👍🏻👍🏻

[@43srgrock]

looks real good. I like the black.

[@CReevesMakes]

Thanks, me too! Although, sawdust brown may have been a better choice lol!

[@HarnealMedia]

Nice build Casey

[@CReevesMakes]

Thanks Steve! 👍🏻

[@congapilon]

Black And yellow on the piping. Lol.

[@diytoolreviews8278]

Dude I would buy this from you decided to sell it ready-made. Such a nice job. It would take me weeks to finish this build.

[@andrew9409]

nice work!

[@CReevesMakes]

Thank you very much!

[@RobRobertson1000]

Ripper job!!!

[@CReevesMakes]

Thank you Rob!

[@marineman2298]

Yep, I would paint the dust collection black at it looks awesome. My problem would have been that I didn't even think about painting it black. Good thinking!

[@CReevesMakes]

Thanks! It’s holding up really well and still looks great! 👍🏻👍🏻

[@CReevesMakes]

Thanks! It’s holding up really well and still looks great! 👍🏻👍🏻

[@barryroberts6470]

Another Excellent build from you, Well done. In answer to your question on painting the pipe, i would have done the same thing and in the black as well, as it matches up with all the Kreg stuff being Black and Blue. Well done again. Barry (ENG)

[@CReevesMakes]

Thank you very much Barry! Yeah the black does a good job of blending everything in. Thanks!

[@charlesreohr6236]

There is a paint product that is used to ground all the components and isolate noise inside of guitars. It is black as well as other colors. It is a little costly but just painting a stripe down the side with a screw at the end will give you an static electric shock stop when connected to a ground. I play an electric guitar and was getting shocked every time I played in my socks. My luthier fixed it with the paint inside of the component cutouts and on the back of the covers.

[@arielalejandrito]

Nice job I loved it

[@CReevesMakes]

Thanks! Its a great addition to the shop! 👍🏻

[@sambullard510]

Yes I would have painted the PVC it adds to your over all scheme

[@protect.your.digits.creations]

Great video , I learned so much . Gave me some fantastic ideas .. Stay creative , Stay well

[@CReevesMakes]

Thank you very much! Glad you got something out of it!

[@Renocide]

Very cool. I like the small clip of you pulling out all the rolling cabinets getting ready to start working. Any vids coming from that new Kreg cutting system?

[@CReevesMakes]

Thanks! That was a fun little add in. Yes I am working on a video with the ACS now!

[@thebobloblawshow8832]

Excellent setup. If I may make a suggestion about your door hardware, I find things constantly get caught on them. I used them in multiple projects for people (they chose them) and alway have the same issue. And yes, I would paint it, great call. Great build. 👍👍

[@CReevesMakes]

Yeah I get what ya mean about the hardware. I haven’t had an issue yet but I can see it happening. Thanks for the tip!

[@idlsjay]

I didn’t see any grooves or means to keep the bit storage slides from tipping down when you pull out the slides or did I miss it? Any way awesome build. I’ve been using Kreg pocket hole jigs since 1999. Glad to see a craftsman use glue along with the screws. I always said the screws were mini clamps that forever remained in place. That’s how I could and would give a forever warranty on furniture and cabinetry. Very “Robust” craftsmanship ✌️😎

[@CReevesMakes]

I added in some simple hardwood cleats to hold the storage slides in. Works well for now. 👍🏻

[@BrothersMake]

Great Job 👍🏼 you have a new Subscriber! We may have to add some of these features to our new router table too! 😁🤙🏽😁🤙🏽

[@CReevesMakes]

Awesome thank you so much! Glad you like it

[@williamhoward8319]

nice job need to build cabinet for my shop but i only have a k4 jig

[@ZacJones]

Great looking build Casey! 1,000% better than that bathroom vanity you were going to use. That foreman looks awesome by the way!

[@CReevesMakes]

LOL I agree! Thank you very much!

[@paulwaldrop]

Great job. Thinking about something like this for my router table/table saw. Understand having things dual purpose and mobile. My shop is 160 Sq ft, so space is at a premium.

[@CReevesMakes]

Thank you and good luck to you!

[@sambullard510]

CR I really like your mobile shop asset I have a small space shop.

[@alawialalawi7474]

good job man

[@CReevesMakes]

Thank you! 👍🏻

[@electrical-woodmetalworksh950]

good job . thak you i like it.

[@CReevesMakes]

I'm glad you like it Thanks!

[@hawkie333]

Holy safety gear!

[@lindrake8315]

Great video as always. I would of painted the elbows of the DC system blue and the rest black

[@CReevesMakes]

I thought about blue at first. I had black in the cabinet thought so it won!

[@glencrandall7051]

I built Norm Abrams router table about 20 years ago but was never happy with the dust collection. You have given me some ideas about making changes that should help. A think casters would help too as my shop is getting a bit crowded. But I think casters may make the top too high. Something else to think about. Good production. good narration and video. As mentioned by others, the music is a distraction. Look up the word "background" in the dictionary. Actually none at all would be better. I watched this video for it's educational value, not for entertainment. The education bit was great. Not so the entertainment. BTW first time viewer. Now I have to check out the rest of your videos. I clicked Thumbs Up, may subscribe.

[@dmoss8928]

When you mounted the router table to the base i noticed you used pocket holes did they go through the router table base or into another piece? Thanks for all the help!!

[@CReevesMakes]

Pocketholes right into the router table top. Worked great!

[@bradhuntsman]

Nice video. I'm curious what you've modded on your cordless ridgid circular saw around 6:15. Aside from the Kreg track saw mount, it looks like maybe a couple items added for dust collection. Thanks for the video.

[@CReevesMakes]

Its a customized Ridgid circular saw. I glued a shop vac nozzle to it and added side shields to see if I could make it dust free.

[@rogerwatson5730]

Top of the line

[@CReevesMakes]

Thank you very much

[@user-ti5df1jg7t]

Отличный стол,молодец!👍

[@81bigcountry]

Great build! I noticed you had dust collection on your circular saw. What are you using?

[@ihatecivicssomuch]

Hands down that is the longest commercial for kreg I've ever seen.

[@CReevesMakes]

Lol, but that router table though 😏

[@CReevesMakes]

Lol, but that router table though 😏

[@CReevesMakes]

Lol, but that router table though 😏

[@giantpune]

At the end around 17:08, when you're showing off the router lift, does the adjustment thingymabob lock in place? You run your workpiece over top of the router elevation adjuster. Is there anything keeping the workpiece from accidentally turning that little wheel and changing the height of your router?

[@CReevesMakes]

Yes you can lock the position and the material will not contact the dial wheel. I have seen some people put a small piece of tape on some of their router lifts to keep the wheel from moving, but I have not had an issue.

[@starjared12345]

Everyone knows painted pipes work better than not painted pipes and it looks better.

[@CReevesMakes]

I agree Jared! Looks much better and more "finished"! Thanks for watching!

[@Snakedriver7478]

you have a fantastic router table set up. Could you tell me what size Empire Framing square you had, It looks larger then 12 inches that Empire sells. Where can I pick one up like the one you have, By the way great videos on all your projects.

[@CReevesMakes]

Hey Douglas! Thank you very much! That’s actually the 12”. I don’t know why it looks so big buts 12”. Thank you very much!

[@matthewpratt8593]

Casey, awesome build as usual! What router did you use in your lift? I am wanting to purchase the Kreg lift, but want to make sure I get a router that fits...preferably Ridgid. Thanks in advance Matthew Pratt

[@CReevesMakes]

Hey Matthew! I used the Ridgid R22002 2HP unit. Fits nicely into the lift. The lift is really easy to set up and use. Good luck!

[@rickymcgrath2314]

holy blade height batman! 😳

[@CReevesMakes]

Yeah, its sketchy but its only for that close corner cut. Every cut I make aside from that is a tooth above the material. Thanks!

[@DW-hn8bk]

Great build which I will adapt for my requirements. Please can you advise where you purchased the slotted driver used in your drill to tighten the hose connectors and what it is called?

[@CReevesMakes]

Hey thanks David! It’s actually just a socket bit out of my Milwaukee driver set. It just fits over the hex of the clamp. Way easier than flat blade bits! Thanks for watching and good luck!👍🏻

[@DW-hn8bk]

CReeves Makes many thanks. Obvious now I've rewatched it! I will replace the slotted screw heads with bolts.

[@gerbiljr1]

@CReeves Makes - Thank you again for showing this part of the video . I am in the process of designing my own woodworking shop in my garage and I continue to change my mind between a Workbench with Casters or without. This video pretty much helps me!! Thank you!!

[@Snakedriver7478]

Great video on the router table you build. What size Empire framing square where you using and where did you purchase it.

[@81bigcountry]

Hi I saw that you had dust collection on your circular saw. what are you using???

[@LZACCARO]

Well done !!!! :-) congrats. L.ZACCARO

[@CReevesMakes]

Thank you very much! It has been an awesome addition to the shop!

[@tallboy12]

Really nice build but after all the effort of matching the grain on the draw fronts and doors why screw the electrical plate from the outside? Having those three screws visible would drive me crazy!

[@CReevesMakes]

I know what you mean but it doesn’t bother me as bad as I thought it would. I may be adding stuff to the table and wanted easy access to that area. Maybe I should have put some more hinges there with a magnet catch? 🤔 now Ya got me thinking! Thanks for watching!

[@zacoberender6595]

Very nice! Can you tell me the overall height, width and length on this fully assembled? Also, if you have the length, width and height on the Miter Table stand you built that would be great. I am thinking that I want to build both of these. Curious about the total footprint and to see if they are the same height as they will likely sit next to each other in my small shop.

[@CReevesMakes]

It is 49" wide x 36" tall x 28" deep (Foreman Platform) The miter station is 96" wide x 36" tall x 24" deep. I have the miter plans on my website www.creevesmakes.com and let me know if you have any other questions! Good luck!

[@zacoberender6595]

So they are the same height! Awesome! Thanks Casey! I just picked up a Foreman and was trying to decide what to do with it. I have about a 14' stretch of wall that I am eyeing for this set up, so they would fit great there!

[@CReevesMakes]

Awesome! Good luck!

[@deucerider430]

Love it! Very well thought out. I like the black PVC but that weird side of me says that I would paint it KREG blue and put a couple of stickers on a few pieces with the KREG logo!No, bad idea! After the thousandth phone call KREG received trying to locate the piece, you might have lost their sponsorship! LOL

[@CReevesMakes]

Lol! I thought about blue but I was afraid it would be hard to match so I went the easy route! Thanks for watching!

[@CReevesMakes]

Lol! I thought about blue but I was afraid it would be hard to match so I went the easy route! Thanks for watching!

[@CReevesMakes]

Lol! I thought about blue but I was afraid it would be hard to match so I went the easy route! Thanks for watching!

[@CReevesMakes]

Lol! I thought about blue but I was afraid it would be hard to match so I went the easy route! Thanks for watching!

[@CReevesMakes]

Lol! I thought about blue but I was afraid it would be hard to match so I went the easy route! Thanks for watching!