Thank you for the time you spent to make and upload this video.
@jakerock_2 жыл бұрын
Thank you for the video. I love the resourcefulness and creativity with very modest tools!
@sourcecreator2222 Жыл бұрын
Awesome video man. I was gonna say for others watching to avoid touching the disc brake contact area with bare hands. But then I saw you clean with spirits after lol. Great to watch and good music too.
@EVCustoms Жыл бұрын
Thank you mate!😄
@andrehehehe46213 жыл бұрын
U can also little warm up the aluminum with torch but careful. Since aluminum is great er thermal Expansion than steel bearings it will expand and the bearings goes easy out
@alireza0713 жыл бұрын
Good works just wondering why didn't u use some high temp silicon on side plate b4 tighten it up to waterproof it
@zoranpocrnja26462 жыл бұрын
If the bearings overheated from the speed especially during summer times can burn all the wires can cause heated pressure even with mild explosion better have some air inside !
@Parabler Жыл бұрын
A hub motor is far more likely to fail from overheating than from rusting so why would anyone put an insulating seal on the motor covers which will make the motor more liekly to fail just to prevent a tiny amount of water seeping through a gap which shouldn't even be visible if screwed up properly and these droplets will usually be evaporated by the motor on the same ride anyway
@MrDeceptacon88 Жыл бұрын
@@Parabler wrong
@ChristianF15cher3 жыл бұрын
There is no way that I would be doing that with the brake rotor still attached.
@kasontrevor9663 жыл бұрын
sorry to be offtopic but does anybody know a method to log back into an instagram account?? I stupidly lost the account password. I would love any tricks you can give me.
@aydenliam74543 жыл бұрын
@Kason Trevor Instablaster ;)
@kasontrevor9663 жыл бұрын
@Ayden Liam thanks for your reply. I got to the site on google and I'm waiting for the hacking stuff atm. Takes quite some time so I will reply here later with my results.
@kasontrevor9663 жыл бұрын
@Ayden Liam it worked and I finally got access to my account again. Im so happy! Thanks so much, you saved my account !
@aydenliam74543 жыл бұрын
@Kason Trevor Happy to help :)
@kna604 жыл бұрын
Damn, you need 2RS bearings that are watertight, not Z or ZZ that are only dust protected.
@EVCustoms4 жыл бұрын
Hi... i didn't know that about dust and watertight, but also previous old bearings was Z...
@46B3x2you4 жыл бұрын
Great Advice. If something fails, don't replace it with the same part. It will only fail. I also didn't know about the difference between 2RS and Z or ZZ bearings. Good point. Fix the cause of the problem; don't just replace and repeat it. I would have made the same mistake if you hadn't mentioned it. Thank you.
@difflocktwo3 жыл бұрын
oh no i got zz too, what if i slather a ton of grease?
@telx2010 Жыл бұрын
@@difflocktwo It then sucks in tons of dirt.
@Richard-qq4bd10 ай бұрын
This is a great video. My electric scooter has recently encountered a problem where the motor locks when moving forward, but it moves smoothly when moving backward, including when manually rotating. I want to know if this is because there is a problem with the bearings. The issue with the motor controller has been ruled out. Thank you, looking forward to your reply.
@zoranpocrnja26462 жыл бұрын
Thanks for sharing to us ,nice one especially from 11:00 good tip with welcome to circus 💪🤣😉😉
@EVCustoms2 жыл бұрын
😂😁😄 Thank you mate!
@FightFilms2 жыл бұрын
Maybe take the rotor off next time to keep the grease off it?
@cyumadbrosummit35344 күн бұрын
Why? Is brake cleaner not available in your country?
@zoranpocrnja26462 жыл бұрын
That plastic pipe is special adjustment does it make any heat?
@E-BikingAdventures Жыл бұрын
Why would you keep the rotor on when doing all that?
@RussellHogan4 ай бұрын
Awesome
@bigcatsliontiger2 жыл бұрын
is ok to apply grease inside motor magnets ? because i did
@asafamor20232 жыл бұрын
Hi buddy Where I can get plastic spacer you install where break rotor side I replace my bearing but I notice that I'm missing this spacer and wheel have play w shaft
@bigcatsliontiger2 жыл бұрын
Bro can u tell yhe size of rear motor ball bearing does 6202 size work ?
@jamesryan78842 жыл бұрын
I have the first version of the Crystalyte Phoenix motor. I would like to put a disk brake on it. Can it be done? Is there a replacement casing ?
@edwinjidat88854 жыл бұрын
I really never seen this motor, very curious about the windings. I think, it blows lot of current with little noises
@seahound3834 Жыл бұрын
THAT'S GOOD
@britkasablja0072 жыл бұрын
8:46 i smashed soo hard but bearing does not move... and even i cracked whole case from smashing... what to do if it does not want go out?
@DJBIGFOOT5STARZ2 жыл бұрын
Did you put red insulating varnish on the stator and rotor ?
@jameskirby50702 жыл бұрын
Does anybody know where I can buy a new axle for my ebike wheel, my thread has totally gone byby
@antonypartali2 жыл бұрын
Γεια χαρά καλλιτέχνη μου!!🙋 Τι γνώμη έχεις για τα μονωτικά σπρέι ή βερνίκια που βάζουν στο μοτέρ (σύρμα χαλκού, μαγνήτες)..??🤔 Έχω ανοίξει τα μοτέρ μου κ δεν ξέρω αν πρέπει να ρίξω κάποιο σπρέι (ή βερνίκι μονωτικό) πριν τα ξανα κλείσω...🤷
@EVCustoms2 жыл бұрын
Geia sou file... tha itan na valeis verniki... alla idiko kai oxi oti na.nai
@antonypartali2 жыл бұрын
@@EVCustoms έχεις κάποιο συγκεκριμένο..?? Να πάω να πάρω αυτό που θα μου πεις!!!
@aliakbari4374 жыл бұрын
what a the great design the stator for less noise I think. what's the power? nice work
@YosdaniPerez-k4d5 ай бұрын
Que rodamientos lleva ?
@clemonsjoey2 жыл бұрын
Where are you located? How much would you charge to refurbish a QS 205 4t motor like this?
@EVCustoms2 жыл бұрын
Hello my friend... i am located in Cyprus (Greek side)
@clemonsjoey2 жыл бұрын
@@EVCustoms Awesome! I’m in the Santa Monica area, so not too far from ya. I’m putting a new QS205 5t on my Enduro Ebike, it’s at a motorcycle shop right now getting laced with powdercoated spokes. I’m wanting to put the old 4t onto a custom stretch cruiser sometime in the next year or so. The 4t probably needs a onceover with new bearings and the threads on the axel was in terrible condition from the previous owner, and needs swapped out or re-threaded with a die, which is why I just bought a new motor. But I want to reuse the old motor on a different bike eventually. Is this a motor a project I could work with you on?
@clemonsjoey2 жыл бұрын
This is the bike I’m modding and upgrading with the new motor right now kzbin.info/www/bejne/m2Gup4Vuqt2me68
@zoranpocrnja26462 жыл бұрын
So better use that last size bearings SKFon both sides looks it's fitting easy!?
@daveed17972 жыл бұрын
Sometimes I find a socket that's close to the O.d. of the bearing without being bigger. Then socket + wood piece + 🔨 - the batteries. I wouldn't be using the batteries as pounding blocks
@김용재-r8i4 жыл бұрын
Very good !!
@justplaymusik17484 жыл бұрын
*EV - Customs* 🏆🏆🏆🏆🏆🏆🏆🏆v
@darexg4 жыл бұрын
Great video! How wide is stator of that motor? What is power rating?
@cyumadbrosummit35344 жыл бұрын
Rated for 5kW but fine for short burst between 8-12kW is what mine sees daily.
@africans19684 жыл бұрын
Can I switch a throttle to remote ESC?
@telx2010 Жыл бұрын
no
@asafamor20232 жыл бұрын
I got crystalyte H series 6.2kw On stealth b-52 bomber
@carpballet Жыл бұрын
Jesus h. Why not show where you attached the puller?
@donwright34274 жыл бұрын
Advice from a professional. You should have upgraded and used 2RS bearings .Rubbers seals .Oh and of you heated the end plates a bit those bearings would come out really easily.
@FightFilms2 жыл бұрын
Less drag?
@donwright34272 жыл бұрын
@@FightFilms Whether using metal shielded or rubber sealed bearings the frictional losses are about the same .The grease does contribute a small amount to frictional losses verses a lightly oiled bearing which would not be suitable for this type of application. Always use a decent brand of bearings as the tolerance and quality control are better . Fitting a bearing correctly is essential as banging it in by the inner ring will cause damage versus pushing it in by the outer shell on a press or by means of threaded rod ,washers and nuts is the correct way.
@dennydewaal1374 жыл бұрын
No silicon seals or gaskets only a oil seal on the Axel ( whits you poult that wiked piece of pipe truwe ) hmmmm Great jop. O and next time put a peace of whod on your tyle Floor before you beat iT whit an Axel 🤔. 😉. Ne great jop
@raystone46734 жыл бұрын
Comment about the tiled floor was spot-on. Something protecting his electrical/electronics workbench too for heavy jobs like this, would help. Good work.
@EVCustoms4 жыл бұрын
Hi... i forget on video edit to put video when i put a screw on axel before hit it on floor. ;)
@MrDeceptacon88 Жыл бұрын
Speak english
@standjel54693 жыл бұрын
Tak tohle je pan umělec opravař...bez lisu bez niceho..