Cue Mixes in

WATCH ALL STUDIO ONE WITH JOE GILDER VIDEOS: • Studio One with Joe Gi...
PRESONUS SPHERE: bit.ly/3zku0vN
STUDIO ONE: bit.ly/2Tfygx0

[@translationstations]

I started this journey in 1988 with Creator/Notator (which became Logic), on a Atari ST with a whole memory of a whopping 2 megabytes of memory, AND, a whopping 30 "megabyte" external hard drive called Megafile 30! Haha... Still have that whole system! Been with Studio One for 10 years now. LOVE STUDIO ONE ❤✋💪😋😛💖💯🎸🎹🥁🎤 And love your vids Joe...

[@TheDrummdude]

The best HP/cue mix explanation i have seen. Thanks Joe

[@gcoudert]

The beauty of signal routing in Presonus' 1810c and 1824c interfaces (and possibly others too) lies in the fact that you can run your main mix into headphone output 1 and your cue mix into headphone output 2, which is very handy when you're working with one other musician.

[@jacksolleguitar]

There is a way to do cue mixes with only 2 output interface. What you do is make an aggregate device and combine the interface with the headphone jack of your Mac in it. Those extra outputs will show up in your I/O setup anytime you plug in your headphones and now you have an extra cue mix for your singer without a big interface :D

[@robmitchell2018]

Thanks for covering this Joe!

[@alexzackary]

I wish I would’ve known this a while ago!!! This is so slick!! I ended up routing all my tracks back through my board like you did with your studio live, but this is way cool!!

[@davecopeland5480]

Great video. Very helpful. Thanks Joe.

[@bobmccarroll7876]

Thanks Joe. That really helped clarify things. Great video.

[@kevinlbrockway]

Another Awesome video!! Loving the Home Recording course also!! Probably going to do the mixing course too.🙂

[@BearPaws_28]

Been looking for a while. This was well put together video. Something to be said about taking your time and giving information in a professional manner. Thanks!!!!

[@postinfinity]

Thanks, that was very helpful. Always a great presentation!

[@briankingart]

TYVM Joe

[@praisethelord20]

This is what I need!

[@lawanedavis7818]

Thank you for this video . I may need it in the future.

[@Capt-Cran]

Really good ... thank you for helping me understand!!

[@keiljazz]

Correct levels for everybody are so very important to helping musicians get their best performance! Might be worth mentioning that this is all for monitoring through studio one. Instead, i usually mix cue mixes during recording sessions on my tablet using the universal control software to monitor directly from my interface (studio 192 + DP88). Might avoid any latency, and keeps the channel look less cluttered.

[@sinaallameh]

thank you so much 😍😍😍

[@jaydee4077]

Good Video. For those of us using faderports, the 16 in my case, it sure would be nice to be able to bring up and adjust those mixes on the board.

[@davideBosco]

Top One man!!!

[@kermasingh9002]

Great info joe

[@GregoryStephenSchumacher]

Joe, are you reading my mind or what? I have a project coming up to produce an album for a Nashville songwriter and I needed to know specifically THIS. Haven't used Studio1 for this kind of thing yet. Last time I actually had an engineer and I'm doing this one myself. Man, this was VERY helpful :)

[@nedim_guitar]

Cue Anon mixes 😂 I don't need this feature, but I watch anyway, because it's fun!

[@bellerosecooks7038]

Thanks Joe. I'm subscribing. Really getting started with studio one. My wife and I came out with a love song called Until Paris by Tiny and Tammy and we did it on Garage Band, but I have had Studio one for awhile now and I really want to get up to speed and this is helpful. Thank you.

[@StephenToddLum]

Also Important for Quantum 2626 - if you're "in the box", the Q2626 interface does not have an internal monitor route, so you use two of the audio outs into, for instance, a Presonus HP4 headphone mixer to get near-real-time headphone monitoring for vocals (there's still a subtle delay but it's like a short slap-back, tolerable). So the cue mix is vital for that application in addition to normal 'open studio' recording situations.

[@mixprofmix]

Another thing I would like to see inside S1 is to bring out Sample One XT FX out as an individual plugin inside Studio One like pedalboard. That way we can use the effects on any sound not only sample one.

[@DMACK1981]

I have a Quantum and was struggling to figure this out. I selected my cue mix to be HP Left and HP Right (Channels 11 and 12 in the I/O diagram) but all I kept hearing was my main mix. Did some research and found out that I needed to use Universal Control to assign the HP 1 output to Channels 11 and 12. By default, the HP 1 output plays the main mix. Now it's fixed! However, I thought with the newest version of Studio One Professional, there was no need to use Universal Control anymore. I'm sure there's a way to assign HP1 to Channels 11/12 as a cue mix, but I'm not seeing it.

[@fritsschoeren7466]

Thank you Joe. I'm using the presonus studiolive 64s and the NSB 16.8. This was what I'm looking for. ( In Dutch... "Geweldig :-)" (meaning > great!!

[@akheron98]

Great tips. But the thing I must check is if I can change the cue mix level of each track with the studio one RC app. Because each member use it to adjust their own headphone mix.

[@bobmarshall2459]

Hey Joe, long time S1 convert and follower. Thanks for another great vid! I cannot seem to figure out how to do what I need, without connecting an external HP amp. Not sure if its possible, and whether its a hardware routing issue, or software routing config issue in S1. Im not clear on how Cue mixes and the Listen Bus work together. In my case with a Quantum 2626. I want my Mix Bus to be clean, routed out nowhere, only for processing mixdowns, bounces, export to MP3, etc. Then on my Listen Bus I have room correction software, routed to Main Outs on the 2626, going to my studio monitors. The issue is that I want cue mixes to be based on the Mix Bus (no room correction), but I cant seem to have a corrected mix going to my monitors, with a clean mix going to my cue mixes. Thoughts? Thanks and keep up the great work w Gregor. Cheers, Bob in NJ

[@WiLyO8]

💪🎬🌲🎶✨Greetings unto Presonus whole Camp etc another day

[@JimpBeats]

I just subscribed.

[@bashawey]

Thanks alote.. Can I use this mathod for Extrnal Reverb Hardware Device???

[@HarleyBob957]

Thanks Joe, you just answered my question…What is a cue mix?.

[@johnarosario4894]

I have the symphony and im trying to figure out what preamp box and like box to get cuz the amount of electric in this room current wise is crazy I can feel it or im just crazy I don't know if I said that right but I am running well ill send pics and maybe you could tell me the best bang for buck because im getting major sound and I have a acoustic treatment coming in well sub walls but its screaming and just the power supply and currents seem so high what should I get or do space is limited but im making it a career so im trying to get worthwhile and time items also

[@pulos42]

I still have troubles with latency. The audio setup in S1 says I should getting 11ms through my Focusrite 18i20, but there is a noticable delay especially on drums. We use our mixer and a patchbay to workaround, but I really wish I could use these features more.

[@RodrigoFloresOficial]

Y cómo enviar los FX a las mezclas? Gracias.

[@LuizMartan]

Hi, is possible put more reverb to singer HO using cue mix when I record a vocal ? How can I do this ? Thanks

[@mixprofmix]

How I wish there is a pan lock on sends as well. It is good seeing how the cue mix pan lock 🔒 with the channel pan, but that is not the case for send, will have to move the slider manually which is annoying. Hope presonus will put this on the next update.

[@tbowles307]

Could you use the “main mix” outputs for another set of outputs for headphones if you don’t have monitors? Example would be for a podcast where everyone would be using headphones

[@goatsnaggler]

So they’re essentially different outputs like the Listen Bus?

[@franckanderson6438]

How do I connect the different headphone outputs for each musician on the studiolive 64s? In the rear MIX outputs?

[@michaelangell9535]

Hey Joe my old interface had a mix knob where I could adjust the playback volume independent input volume. like my guitar over the rest of the mix. How do I make that adjustment with out that knob? I have a 2626. Thanks

[@andyanders]

Good job explaining, Joe, but I can't get it to work with my AudioBox 44VSL. It used to come with onboard mixing and cuing, but Presonus dumped that after Apple changed their audio handling (or something...) I followed your instructions, but the Cue didn't come up in the insert tab of the channel. Any ideas?

[@DreamslideProductions]

ok so in my workflow i have everything in folders, Vocals, Drums, ETc.. it my starting template. when you use folders the cue mix only works on the folder track and the tracks in the folder. is it possible to change this behavior? i know the work around is to temporarily move all the tracks out the folder but figured id ask incase there was a setting i was missing.

[@RobertMatichak]

@presonus I noticed that there are post fader inserts on the cue outputs. There are also post fader inserts on the Master and Listen bus. Why would anyone place an insert post fader? Great video. Thx.

[@markhofland1898]

What do you with pre-recorded material in S1. B.e. Drums, bass, keys. And b.e. A singer needs to be recorded after. How to get the cue mixes from s1, through the console to the singer?

[@chrisbottoms6396]

Cue mix would be more useful for me if I could use it for two mono cues instead of it forcing me to do one stereo cue. It's a great feature that doesn't really help me. TEMPORARY WORKAROUND... What I did as a workaround was to create two stereo cue mixes named Monitor 1 and Monitor 2. In the insert of each, I put an instance of dual pan and panned one hard left and one hard right. If anyone does this, just remember than any effects that you want to add directly to the either of the cues need to be placed before the dual pan, or else your effects will throw it into stereo again.

[@jerialice]

Also I have a multi channel headphone amp…can I use 2 pairs of outputs on that in the routing scheme. So far I have the main going out to my nearfields, pair 3/4 to headphone amp, 5/6 to a different set of monitor speakers.thank you!

[@jerialice]

Joe, we have 3 devices connected to outputs for monitor sends. How does the outputs 1&2 on the back of my Studio 192 correspond to the main mix output?

[@ericpeterson9336]

cool... I made 4 on my new to me handed down StudioLive 24.4.2 .... I named each of the four cue mixes Ace ,Gene, Paul and Peter . Just in case the guys show up. I mean....you never know

[@martinchamberlain8948]

Are there any plans for Presonus to add the ability to route FX channels to cue mixes directly (without having to go through the messy process as described by another commenter)? Thanks, Joe. Love your videos.

[@joesteel5180]

Maybe in Fender Studio 6

[@johnpasquarelli9268]

I have followed this video over and over but: In my console view studio one 5 pro, the only channels that the cue mix shows up under sends is a channel routed to Main bus which I'm not using. My channel outputs are all routed to "stem" buses" I've assigned to each group and outputting to stereo outs in my matrix. How do I fix this??

[@rjmikael]

Hello sorry, u said, u use studiolive mixer, i use studiolive 16.4.2 AI, And how to connect my mixer to studio one mixer ? I just want my mixer faders syncronize with studio one mixer faders, Please help Thank you

[@PianoPoet481]

I want to play Piano. But in my headphone I want to hear a beat or a metronome. Is it possible! ?

[@agesonjohanesburg2915]

Joe I can pan my cue mixes but when I go to mix it and remove the cue mix output etc- I can not PAN at all. Help por favor? Grazi

[@victorfrancco]

is it possible to set up mono cue mixes?

[@DeltaWhiskeyBravo13579]

I don't think so, cue mix seems to be stereo out, with pairs of output jacks.

[@PinkFloyd793]

Is it possible to send all the channels via adat on your interface to the Behringer powerplay 16?

[@koolstreamrunnin]

Question, my output faders do not seem to control anything. For example I have a Headphone Amp out puts 5-6. I can adjust fine in Focusrite control, but the output faders that correspond to these do not seem to do anything. Help

[@felipemontana8815]

Why isn't this function part of the Show page?

[@stevehinan]

💪

[@nicknash2008]

When a new track is created, it automatically turns ON and turns up the cue mixs that I have set up. Is there a way to NOT have it turn them on and up but still create them?

[@myert1]

I've watched many videos on cue/headphone mix set-up. Not one has addressed the obvious for a newby. WHERE DO YOU PLUG IN THE HEADPHONE JACK?

[@jameswillis2k23]

So question for anyone who can help…. I followed the steps exactly and repeated the process a few times and the cue mix icon pops up in the faders It doesn’t have the. “Power on/off” or the “lock/unlock” icon next to them. What am I missing?

[@DeltaWhiskeyBravo13579]

Only a guess: Do you know how you can slide the sections of the top of the faders? I mean the areas like insert, send, cue each should overall slide into and out of view. Start at the fader and move your pointer upward until you get the moving divider, probably the first one. Drag the divider until the cue area appears. You might first need to slide the fader section down to gain room for the top to show better too.

[@JackBrownDrums-ih6le]

I have studio one artist and I see the cue mix on my track but I cannot adjust - do I need a different version of Studio One ?

[@DeltaWhiskeyBravo13579]

I've just begun dabbling with setting up cue mix. It appears you can adjust individual horizontal cue faders just like Joe showed. I am on S1 6.1 Artist.

[@robertoreynoso6312]

Hello, I would like to know if anyone has experienced that the main output channel suffers volume alterations when the content of a track is assigned to a specific monitoring output. thank you

[@Romlingen]

Here is a tip on how to also send FXs (reverb, delay) to head phone mixes as well. kzbin.info/www/bejne/bYnUZWuBmtOnqJY

[@RuCatania]

Thanks. That's a big bug, since 9/10 all you wanna do is add some reverb to the singer HP. And in the creation/recording process nobody cares about some ms of delay in the reverb out, it's just like a small pre-delay setting (if this is the problem about routing FX to CUE).

[@Magichandzpro]

Anyone can tell me why Studio One sounds different than cubase or pro tools. Same specs, configuration, sample wav loops, without processing, just the audio samples, and the sound in studio one sounds more tiny and muffy. Kicks have so much click and less low end. 24bit 48000khz in both! Same Pan Law! I love Studio One workflow but i prefer sound quality! Sorry for my bad English.

[@kylesmith6095]

Here lies my main complaint with Studio One Pro 5. If the vocalist wants some verb your forced to create a second cue mix to send to their cans! Forget about all the color schemes and gear S1 for people actually playing in a room together not one over dub at a time. And yes PreSonus has a work around but their tech couldn't figure it out. Love the DAW except for this.

[@stefanfelssner]

Pleeease post-fader „send level“ option for cue mixes finally 🥹