Custom Rod Building Tools, Make A Custom Fishing Rod! Now On eBay! Features, Assembly, How To Use

[@TheFishingHobby]

Shortcuts to different segments of the video: 00:00 Introduction 01:10 Features And Benefits 15:46 Changes From The Original Prototype 16:40 Assembly 22:00 Using The Thread Carriage 34:42 How To Replace The Rod Holdowns And How To Use Them 35:40 Thread Routing 36:43 Basic Wrap Using Non-Metallic Thread 42:06 Basic Wrap Using Metallic Thread

[@mattyjepatie]

Thanks very much for all your time and effort. Great job. I am amazed. Are you still making these? Im a surf fisherman and fish with a 14 foot rod. This would be great for wrapping.

[@TheFishingHobby]

Yes I do, I've sold a lot of them! Here is the eBay link: www.ebay.com/itm/142777828781

[@marinerodeaguadulce7026]

I am interested buy 1...... i went on Ibay but none available......are you gonna build more ??? Let me know

[@TheFishingHobby]

I will be making more next week, thanks for checking in with me!

[@vanthangnguyen5627]

tôi muốn mua 1 bo này mua ở đâu

[@jonathanluce9130]

Fantastic simple design, I liked the way you worked through the problems you encountered.

[@mikeburgess9617]

In spite of this being an 'older' video and knowing that the setup you have shown us is no longer available to purchase, it's been amazing. Watched loads of similar videos on all sorts of setups, but this is by far the simplest to follow and come up with a home-made version. Your reasoning behind so many of the smaller - but very important - design features has itself been sooo helpful. And your guide on starting even the simplest wrap has also been the best (for me) I've seen. Thanks so much for this.

[@benskai2475akurfishing]

Greetings coming from Indonesia, healthy greetings and greetings from fellow fishing rod craftsmen and senior creative greetings

[@fiorevitola880]

I can recommend this seller first hand, I have had him build me some parts for my auto lathe. The workmanship is impeccable. He is a conscientious builder.

[@TheFishingHobby]

Thank you!

[@lucasdominguezandamoyo6245]

Nice job, simple and useful.

[@shastasteve]

Well thanks for the very fast shipping. Very well packaged. Took two minutes to put it together. Like any new toy I could not wait to try it out. I grabbed one of my old sturgeon rods and proceeded to replace one of my broken guides. Actually harder to prep the rod than it was to wrap it. Turned out great for a first attempt, if I do say so myself. I love the tension system. The wire is great and allows several wraps in reverse if you get in trouble. Now I just need to get a better selection of thread and guides and I will be off to the races. I still have to flex coat my repaired guide but the wrap job looks good. You did a great job designing this and I am very happy with my purchase. For repairs and the amateur rod builder this should work great .

[@TheFishingHobby]

Excellent! Thanks for the feedback. I really like it but I have been building/repairing rods for several years now and have actually built several different jigs as well. I'm really glad to hear you were able to use it effectively right out of the gate! My hopes were to make a jig a beginner could get really good results with.

[@michaeljwagner7968]

Nicely done!

[@kirkamerson2756]

Just received this kit yesrterday . very good quality martial and workmanship on this kit.Going to practice on a fiberglass glass rod tomarrow rapping

[@TheFishingHobby]

Excellent! Be sure to let me know if you have any questions about using it. I'm always happy to help if I can 👍

[@tigershark01-q5g]

thank you....I've learned alot from your video.....

[@timclarke1791]

My rod jig came yesterday I’ve just used it today ..so pleased with it .. it’s a very good peace of kit well done for making them Excellent 👍

[@TheFishingHobby]

I'm glad you like it and thanks for posting your comment here too! Is this your first time working on fishing rods? If so, are you figuring everything out okay?

[@timclarke1791]

The Fishing Hobby yea started about six months ago got a lot to learn ..wasn’t happy with the tension system on my CRB wrapper so decided to try yours so glad I did ..keep up the videos learnt a lot of you ..stay safe 👍🏻

[@TheFishingHobby]

The CRB setup could be decent if they redesigned the tensioner and made it so that it wouldn't change on you while using it. Probably wouldn't be too expensive to do. I guess they just don't want to bother with it, but they have to realize it is a problem. I've sold a few jigs to others that say the same thing. One person said he got so frustrated with it that he saved the stands and threw the rest of it away after he got mine. I would think they would look at reworking that part of it just to keep their customers happy with the products they sell. It is what it is I guess. Thanks and you stay safe as well!

[@timclarke1791]

The Fishing Hobby I’ve kept the stands and my CRB drying motor there really good .. but I will never use the jig again now I’ve got yours .. I’ve sent your KZbin link on some of the face book rod building pages Iam on ..and it’s getting good fead back already. So if you start getting lot more orders in UK 🇬🇧 don’t be surprised..

[@TheFishingHobby]

I've sold 4 to the UK so far. I've had a few people tell me the import duties are pretty high your way. I've sold 6 to people in Australia and that is the most to a country outside of the USA so far. I've also sold some to people in Malaysia, Spain and Italy. It is kind of fun to send them out to people in different areas of the world! It is a little hard to believe the jigs that were born in my shop have found their way to such far off places! I knew after I built the first couple of prototypes and used them that I was onto something that really worked well. I had already been building rods long enough that I was pretty good at it, and the prototype of this design made the whole process so much easier than what I was accustomed to that I thought they would be really handy for people just getting started. I also thought it would make the wrapping process more enjoyable for experienced rod builders too. I felt like I should start building them to sell, and that has been a rewarding learning experience in itself. Thank you for taking the time to reach out to me with your feedback on the jig!

[@EASTSIDERIDER707]

Nice clean work.

[@bobm549]

Nice rig, excellent . Got a stack of hdp scraps and am gonna rebuild my wrapper . Your jig is a Good design and I would advise anyone to get one. Much easier than having to build one . Hope to see you at the trout stream !!

[@TheFishingHobby]

Good luck with the jig build and thanks for the compliment 👍

[@frankracz6736]

When I saw the picture I knew who was building these! Great job.

[@TheFishingHobby]

Thanks my friend LOL

[@MrRODMAKER]

Where can I get one of your wrappers,you talked about putting it on eBay .Also do you have a web page.

[@TheFishingHobby]

Richard Curry, I do not have a web page, but I do have a Facebook page here: facebook.com/The-Fishing-Hobby-622235554778488/ Here is the eBay listing: www.ebay.com/itm/142777828781 You can also email me: [e-mail] Thanks!

[@YankeeTankerOutdoors]

so bad ass.. I am gonna share this with my buddies who make rods.

[@TheFishingHobby]

Thanks man...it took a lot longer to get this going than I anticipated but I wanted to make sure I covered all of my bases!

[@BlackWarriorLures]

Oh, man! Heck, yeah! I've been thinking about building a couple medium catfish rods for this season.

[@donpowell1092]

TY I,m very impressed with the unit and the way you thought it out. Just thinking about getting started in rod building and searching for best tools to use Your's stand way above all others so far.

[@donpowell1092]

I'm now a Sub looking forward to future How To Vids.

[@TheFishingHobby]

Thank you! I have heard nothing but positive feedback about the wrapper and I've sent them as far away as an island off the coast of Italy! I spent several months working on the design and it feels great to hear positive feedback from professional and hobby rod builders alike. It feels like all of the time I spent working on the design really was worth the extra effort. I'm currently developing a power wrapper for people who build bigger rods or people who would just prefer to have one over a hand wrapper. I personally enjoy using a hand wrapper, but I had enough people ask about the possibility of me making one that I felt like it would be a worthwhile project. I actually built a carriage for a power wrapper for someone who asked if I could make one based on the tensioner setup on the hand wrapper, so I did that for him and he said it was a great improvement over the one that came with his power wrapper. During that process I saw a lot of shortcomings in entry level power wrappers and that made my mind up for me. I have been working on the power wrapper ever since. I'm almost ready to build a prototype! I don't know if you use Facebook or not, but I have a page there where I post a few things that aren't on KZbin you may find interesting. Here is a link if you want to have a look: facebook.com/The-Fishing-Hobby-622235554778488/ I've been working on the power wrapper so much in my spare time that I haven't done a new video in a while, but I will be doing more KZbin videos too. Sorry about the long reply 😁 Glad to have you as a subscriber, I hope you enjoy the channel and if you ever have any questions about rod building let me know, I may be able to help 👍

[@dennykarsjen1920]

@@TheFishingHobby I'm not finding it on the eBay. can you go ahead Let me know where I can get one. Very interested.

[@TheFishingHobby]

I am no longer making the wrapping jigs. I lost my supplier for the HDPE plastic I made them out of and it was by far my cheapest option for the HDPE. I would have needed to increase the price too much so I opted to stop making them instead.

[@deuces2k]

Love the detailed explanation of the tension rod. I was trying to figure out the benefit and you answered everything!! Great looking setup

[@TheFishingHobby]

Thank you! They work really well 👍

[@MuskyHans]

Nice looking jig

[@TheFishingHobby]

Thanks Musky!

[@treasurecoastanglers1003]

This is great 👍

[@AntonisDiakakis]

That looks so wicked!

[@CAM67]

Good stuff bro!! That is really good info. Thanks for sharing😉👍

[@TheFishingHobby]

Thanks CAM!

[@antoniosolari1013]

Would you tell me where I can find the spring steel that is used to keep tension on the thread .

[@TheFishingHobby]

I use .039” music wire which is spring steel. 1mm spring steel wire or music wire should also work, very similar diameter.

[@antoniosolari1013]

Thank you .

[@shastasteve]

That looks awesome. I have to admit when I fist saw your system I was just going to build my own. I looked at what you are charging on Ebay and I am not sure I could build one for what you are charging. Ordered one today. Can't wait to get it. I have a lot of poles around here that are missing an eye and with with they charge to put them on this should be great. Great video.

[@TheFishingHobby]

Shasta Steve thanks for the comment! I just shipped yours out a few minutes ago and look forward to hearing what you think about it. Yes sir, they aren't cheap to make and then there are fees and shipping costs that factor into the final price. I tried to price them fairly and there are less expensive options available, but I feel pretty strongly that people would find it difficult to buy another wrapper that is as versatile and solidly built for the price. As you mentioned, when you start pricing the materials to build just one the cost would probably come out to a similar amount plus the time, tools and effort involved. I purchased fairly large quantities of materials to bring the cost down and still allow me to make a profit. Looks like I need to start making more, only 1 left! I hope you enjoy it and I would love to hear any feedback you may have. I tried to cover all of my bases in the design of it but I'm always open to suggestions for improvements and would consider them in future builds. Thanks again, and I hope to hear back from you after you have had time to try it out.

[@pakde8002]

Probably already mentioned but aluminum tube or 3/4" grey PVC pipe for electrical conduit is also readily available and probably heavy enough especially up to 3 feet. For a longer length the galvanized steel is probably better.

[@pakde8002]

Really nice set up btw. Good luck with the sales. I'll have to diy it as the shipping would be over 100 bucks to Indonesia 😔

[@TheFishingHobby]

@@pakde8002 wow, that is a lot for shipping! I've sold quite a few of them (67 through eBay and 10 to an organization that teaches rod building to disabled veterans) 👍 They work really well!

[@Nittytash]

Hi,love watching your infomative videos sir,i was wondering if the size bolts you use are compatible to suit the diff sizes of thread spools,could you state what diamiter the threaded bar is please....thank you.

[@TheFishingHobby]

I use 1/4" x 20 thread

[@enthusiasticfisherman1229]

So cool man! Very good!

[@ropermrmeredith06]

WOW!......great rig.

[@TheFishingHobby]

Thank you! It is a great setup. Makes wraps an easy task.

[@vinfish4697]

excellent Design

[@TheFishingHobby]

Thank you!

[@mikeburgess9617]

Ah ha .. as I now see that you're still keeping an eye on this page/video/comments, I hope you don't mind my asking for yet more advice. Pretty much drawn up my version of your design, but just wondering your view on using a pair of connecting tubes (mine will be steel rather than ali) v's a single one. My rod supports will not be in such an exotic material (just MDF), I wondered if having a pair of rods would increase the stability and reduce wear on the rod stands. Fingers crossed for a reply.

[@TheFishingHobby]

MDF is actually a good choice of materials, just make sure to line your V cutouts with some felt (wood and MDF are abrasive). The metal rod is just there for alignment purposes really so single or double shouldn't make much difference.

[@mikeburgess9617]

@@TheFishingHobby Many thanks - yet again. I already have some felt or the 'soft' side of velcro (self adhesive) for the "V" lining.

[@PhillipPierceall]

are you still selling these I can't find them on ebay?

[@drehasadd]

Very cool!

[@TheFishingHobby]

Thanks!

[@dashermike3207]

Very good quality. Are the two holes in the upright piece that hold the all thread rod threaded? Just wondering how you keep the allthread rods from turning? I probably missed something here but I don't see any mention of this. Thanks and I look forward to more instruction.

[@TheFishingHobby]

There are washers, lock washers and nuts on each side of the threaded rod that lock it into place. They don't turn at all, very solidly mounted into the upright.

[@latinovision]

Wow great job

[@TheFishingHobby]

Thank you and thanks for the logo! Still using it!!!

[@latinovision]

@@TheFishingHobby looks like you have had great success my friend. You deserve every bit

[@TheFishingHobby]

Thank you, I really appreciate it!

[@EliteBassStickFishing]

Awesomeness!!!💯💪👊LET'S GO!!!

[@sohelnaser4608]

Amazing thank you very much!

[@claytons.124]

Good morning ! I loved the project! How do I buy it ?

[@TheFishingHobby]

I’m no longer making these. I lost my hdpe supplier and would have to charge too much to make them now so I have started working on a new design quite a while ago. It is almost ready and you can see a sneak preview of the new wrappers here: A Sneak Peek! New Hand Wrappers For Rod Building Coming Soon! kzbin.info/www/bejne/q52piKidnpaoeMk

[@RalphBarton-fishing]

Good looking stuff

[@Interp66]

Look great 👍

[@randallcorbello2857]

I would love to see about purchasing one did not see the link for eBay

[@TheFishingHobby]

I am no longer making these because I lost my HDPE supplier and they were by far my least expensive option. I would have to charge too much to continue making them. I'm currently working on a 3d printed wrapper, but I haven't finished designing it yet.

[@ThisIsAnglerTV]

Looks good!

[@TheFishingHobby]

Thanks!

[@sassyfamilie]

Nice job my friend 😃 sweet greetings, sassyfamilie 😉 thump up for this video 👍

[@donpowell1092]

Very nice set up. Question for you . Could you not super glue a ceramic eye in the tension rod and it can then be used for metallic thread? just thinking.

[@TheFishingHobby]

You probably could get away with that or even just use the tension wire as is. It really just depends on the metallic thread you are using and how sensitive it is to deformation from pressure applied to it. Some metallic thread is pretty rugged and some is more fragile. You could always do a test wrap and see how it goes. If it doesn't work out, just wrap directly from the spool. Great question and hopefully this info will be useful to others as well. Thanks!

[@mazturcfc8377]

Hi bro. long to hollow shaap? Cm?

[@murderinc.hunting7686]

Awesome👍🎣

[@paulluechtefeld6409]

Kevin I am very interested in buying one of your wrappers do you have any at this time?

[@TheFishingHobby]

Yes sir, I sure do! I have 9 available right now. Here is a link: rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F142777828781 And if you ever need the link again, it is in the description box of this video as well. I've sold 30 of them so far and had nothing but positive feedback. I'm sure you will be happy with it should you decide to buy one. Please read through my eBay seller feedbacks and you will be able to see what others think about it. Thanks for checking in with me about the wrappers and please let me know if you have any other questions about it.

[@paulluechtefeld6409]

@@TheFishingHobby great thanks

[@TheFishingHobby]

@@paulluechtefeld6409 no problem!

[@mikeburgess9617]

Hi. Me again. One final (probably) question. What diameter wire have you used for the tensioner? Don't mind how you quote it - SWG/AWG or mm.

[@TheFishingHobby]

It is .039" diameter music wire 👍

[@mikeburgess9617]

@@TheFishingHobby Thanks loads again. According to my (on line) tables, that makes it 18 or 19SWG. I'll go hunting for that - the final bit missing from my built kit.

[@TheFishingHobby]

@@mikeburgess9617 I think 18ga would be about right. Good luck 👍

[@erichalbert3278]

How much are you selling them for ? I'm interested

[@TheFishingHobby]

I'm no longer selling these. I lost my source for HDPE that I made these jigs out of and it was by far my cheapest option. I'd have to charge more than I wanted to keep making them with a different supplier, so I opted to stop making them.

[@tonianik2878]

thank's you bos,,,mantuulll.

[@BlackWarriorLures]

I wonder if I could use it to wrap my floats? Doing it totally by hand has proven too slow. A rack like this might speed up the process.

[@TheFishingHobby]

I would think so. I have seen your floats and some of your build videos but I can't remember if you had one that shows the wrapping process. Do have one that shows the process you could link me to? It would give me a better idea of what you would need and if this jig would work for you. I know we have emailed each other before, but here is my email address again if you want to talk more about it or need to send pics or anything: [e-mail]

[@gregschlitz4043]

Do you have any available now?

[@TheFishingHobby]

I do! Here is the listing: rover.ebay.com/rover/1/711-53200-19255-0/1?icep_ff3=2&pub=5575378759&campid=5338273189&customid=&icep_item=142777828781&ipn=psmain&icep_vectorid=229466&kwid=902099&mtid=824&kw=lg&toolid=11111

[@edholloway7857]

Very nice design--Where in Arkansas are you?

[@TheFishingHobby]

Thanks! North of Conway if you are familiar with that area.

[@edholloway7857]

Very familiar----I live in San Antonio TX. now but originally from NE Arkansas---I was a member of SW City Bass Club in LR when I lived in Searcy (Worked in Beebe)---My sister lives in Russellville

[@TheFishingHobby]

Nice! We fish over at the lakes at Village Creek State Park near Crowley's Ridge occasionally. Beautiful area in NE Arkansas

[@edholloway7857]

I'm from Pocahontas/Imboden area east of Jonesboro

[@TheFishingHobby]

We we're just in that area last weekend. My kids were bowling in a tournament at Jonesboro

[@SlowPitchJiggingSXM]

Great video! Do you still sell these???

[@TheFishingHobby]

I do! I have more but I set the quantity available to zero for now because I'm out of town with my family for spring break at the moment and unable to ship them until I get back. I'll update the quantity available Monday 3-29-21 on the eBay listing link that is in the description box of this video. Thanks for checking in with me about them.

[@waterman3911]

👍👍👍👍👍

[@dashermike3207]

Which Mod Podge product do you use for your rod wraps?

[@TheFishingHobby]

The one that says glossy and I think the label on the bottle is red.

[@dashermike3207]

The Fishing Hobby yep. just found it at walmart thanks

[@TheFishingHobby]

No problem 👍

[@CaptJimmysLivingTheDreamFishin]

trying to find a link or something on how to maybe order one of your wrapping units...

[@TheFishingHobby]

I sell them here: rover.ebay.com/rover/1/711-53200-19255-0/1?icep_ff3=2&pub=5575378759&campid=5338273189&customid=&icep_item=142777828781&ipn=psmain&icep_vectorid=229466&kwid=902099&mtid=824&kw=lg&toolid=11111

[@fiorevitola880]

You made a thread Shuttle for my wrapping machine Joe from AT site

[@TheFishingHobby]

Hello Joe! I ended up going down a rabbit hole after that Hahaha! I've been working on a power wrapper ever since and it has been an experience for sure. Don't know when I will get it done, but I will eventually!

[@fiorevitola880]

I subscribed to your channel. Do you ever visit the AT site anymore? I have a business now it's Off the Hook Rod & Reel. You can give me a shout at [e-mail]. Good to hear from you buddy and keep up that good work.

[@TheFishingHobby]

Haha, sorry I guess I forgot to respond here but you already know I went and checked it out 👍

[@babylife30]

hello or can we find the stl file to print the mounting bench? thank you

[@TheFishingHobby]

These were not 3d printed so I don't have any files.

[@babylife30]

@@TheFishingHobby Ok thank you

[@philipholwerda4347]

Will you be adding more of these to ebay? It shows out of stock

[@TheFishingHobby]

Yes I will. I have been out of town, but I will get some more listed after I have a couple of days to build some more. I should have some ready to go this week. If you want to send me an email - [e-mail] - I can let you know when I have them listed. Thanks!

[@TheFishingHobby]

I have some more jigs built and listed now, thanks! www.ebay.com/itm/142777828781

[@woefman9467]

Awesome Video, you mean i watched whole thing and can no longer purchase the jig ?? grrrr

[@TheFishingHobby]

Sorry, just too expensive now to make without having to charge a price that too high.

[@rickk1708]

Where can I buy this?

[@TheFishingHobby]

www.ebay.com/itm/Quality-Fishing-Rod-Guide-Wrapper-Wrapping-Jig-For-Building-Rods-See-Video-USA-/142777828781?_trksid=p2349624.m46890.l49292

[@uket55]

Where can I see the dimensions of all the parts?

[@TheFishingHobby]

I never used plans, I just built jigs to easily duplicate the original that I built several years ago.

[@uket55]

@@TheFishingHobby Thanks for the reply.

[@jorgecruz7781]

Muy bien

[@scottluft3415]

How hard is it to wrap a tip and top guide?

[@TheFishingHobby]

It is easy. Just move both stands on the alignment rod to the same side and move the thread carriage outside of those stands. You can watch this video at about the 7:00 mark and see how to set up for wrapping tip tops.

[@scottluft3415]

@@TheFishingHobby how would th he other end of the rod be supported?

[@TheFishingHobby]

With the 3rd stand

[@scottluft3415]

@@TheFishingHobby woohoo! Thank you for your quick response!

[@TheFishingHobby]

No problem! If you have any other questions, feel free to ask away!

[@adonisfishingvlogs9013]

Sir is this available ?

[@TheFishingHobby]

I no longer make the wrapping jigs. I lost my supplier for the HDPE plastic I made them out of and it was by far my cheapest option for the HDPE. I would have needed to increase the price too much so I opted to stop making them instead.

[@adonisfishingvlogs9013]

@@TheFishingHobby ok sir, thank you sir, godblesss you keep safe alwyss...

[@rickk1708]

I couldn't find it on EBAY.

[@TheFishingHobby]

I'll have more ready next week. I'm out right now, but I will have more listed by next Tuesday. www.ebay.com/itm/Quality-Fishing-Rod-Guide-Wrapper-Wrapping-Jig-For-Building-Rods-See-Video-USA-/142777828781?_trksid=p2349624.m46890.l49292

[@FilipinoBMW]

Are you still selling these?

[@TheFishingHobby]

I’m no longer selling these. I have a new one that I have been working on for a long time that is almost ready for me to start producing but it isn’t quite ready yet. I’m going to post a sneak peek on my channel as a short form video tonight or tomorrow.

[@hanskoehoorn756]

can you send to the nederlands

[@TheFishingHobby]

I'm not currently making these. I lost my supplier for the HDPE that I used to make them.

[@kstromlundks]

should have used drilled and taped holes and used machine screws not drywall screws the will strip out at some point just saying but all and all great design

[@TheFishingHobby]

Drywall screws hold better in HDPE than machine screw fasteners. I actually tested that out myself before I started building these to sell. I think the reason is because of the shallow thread depth of the threads on machine screws. The differential between the major and minor screw diameters are larger with drywall screws if that makes sense. What I do here is drill my holes to the minor diameter of the drywall screws and then the screws cut their own threads as they are driven home. HDPE machines more like metal than wood does but the screws made for wood hold better in it. The thinner/shallower threads of machine screws strip easier in HDPE than the more coarse threads of screws made for wood. I hope all of that makes sense, but I thought the same thing until I actually tested some pieces in the shop. Thanks for the compliment too! Tight lines 👍

[@TheFishingHobby]

After this comment, I decided to check online for literature on the subject and it confirmed what I found in my own testing, use screws made for wood or threaded inserts if you want to use machine screws. Threaded inserts would be overkill in this application and would also require the use of smaller diameter screws due to the fact that the HDPE used in the jigs is only 12mm wide...that would have to be a very small diameter machine screw so that the insert itself would be small enough in diameter to fit the 12mm thick HDPE. Here is the article if anyone wants to read it (it has a lot of other good information in there): www.google.com/url?sa=t&source=web&rct=j&url=www.emcoplastics.com/assets/pdf/HDPE/HDPE%2520Fabrication%2520Guide.pdf&ved=2ahUKEwi305GOlcvhAhVLM6wKHX2nCcYQFjAAegQIAxAB&usg=AOvVaw1qPj0o75fcyGK4F4Ig_kJ9

[@irwansofiana3184]

Pengen sekali

[@-fishingvideos-liorben-hai2447]

Hi Great channel my friend I like it! I sub you now I have a fishing channel to And I invait you to enjoy from it

[@fuq584]

Man these are crackhead prices 90$ for not that gret material for the wrapping jigs. You can find much better quality ones for a few dollars more you can get a motorized one with all aluminum construction 🤣

[@TheFishingHobby]

Could you do everyone a favor and post the link where you can buy all aluminum construction power wrappers for a few more dollars than $90? Thanks in advance!

[@fuq584]

@@TheFishingHobby www.mudhole.com/CRB-Turnkey-All-in-One-Freshwater-Rod-Building-Kit-56-Light?quantity=1&custcol_kit_reel_seat=4 Go to mudhole.com they have turnkey kits with everything you need to build your first rod :) if you need me to find some more ill link em later

[@TheFishingHobby]

@@fuq584 that is a CRB hand wrapper, not an all aluminum construction power wrapper like you described. The wrapper is plastic and the stands are steel. Buy the CRB hand wrapper and have fun with it. It is fairly usable. This gentleman threw his away (but kept the stands) after buying mine. People who started with the CRB wrappers make up a lot of my customers. facebook.com/622235554778488/posts/848768575458517/ Jim owns a custom ice rod building business called Striket Custom Rods which you can find here: facebook.com/Striketcustomrods/ Ask him what he thinks about the CRB hand wrapper compared to mine. I don't need a beginner rod building kit, I've been building custom rods for several years now. Go through and look at my videos, they may help you out as you get started. Good luck with your rod building. It is a rewarding hobby.

[@georgemacdonald3087]

Is your name, Richard?....'cause you are definitely a Dick.

[@stevenbaumann8692]

Excellent work!

[@TheFishingHobby]

Thank you!