Customer States: I Think I Need Brakes!?

  Рет қаралды 380,439

South Main Auto LLC

South Main Auto LLC

Күн бұрын

Пікірлер: 1 200
@SouthMainAuto
@SouthMainAuto 2 жыл бұрын
*Best Brake Lubes:* CRC 05361 Silaramic Brake System Grease - 5 oz. - amzn.to/3GfUkOe Super Lube 97008 Silicone Lubricating Brake Grease with PTFE - amzn.to/3AmWHuN
@jptrainor
@jptrainor 2 жыл бұрын
The video shows Super Lube silicone brake grease. The link in the comment is to regular synthetic Super Lube which is less suitable for caliper pins.
@joesilverbliss1721
@joesilverbliss1721 2 жыл бұрын
Thanks!
@LeverPhile
@LeverPhile 2 жыл бұрын
@@jptrainor He uses both I think. When he is greasing up the caliper brackets for the pads, he uses the CRC lube, spreads it with an acid brush. Same with the caliper itself. Nice catch about the Amazon link. The various SuperLube labels can be confusingly similar.
@174joedirt
@174joedirt 2 жыл бұрын
what happened to the purple brake lube ?
@tonywestvirginia
@tonywestvirginia 2 жыл бұрын
Actually the rotor "Keeper clips" is so going down the assembly line they don't fall off and someone gets hurt. I worked at GM for a few years. When I do brakes now, I just toss them away. Why am I watching you do a brake job? Because I love your videos my friend.
@ice44567
@ice44567 2 жыл бұрын
I can't believe you sold this man a brake job when you could have just turned his radio up and sent him on his way! Lmao, excellent job as usual.
@johngassmann9581
@johngassmann9581 2 жыл бұрын
Exactly!
@K.Kelly87
@K.Kelly87 2 жыл бұрын
🤣🤣🤣
@markadams5429
@markadams5429 2 жыл бұрын
That would be mostly women drivers, re: my wife and my mother! Lol
@dalerush9724
@dalerush9724 2 жыл бұрын
My radio quit working and I could hear everything wrong with my truck.. I installed a new radio with louder speaker's.. A cop tried to pull me over for having no rear view mirrors, but I couldn't see or hear him behind me! 😂
@jameshedrick605
@jameshedrick605 2 жыл бұрын
I grandma had a bad wheel bearing on her car she took it to the dealer to have it replaced and they told her turn up the radio and you won't hear it. That was before i started working on cars
@elcheapo5302
@elcheapo5302 2 жыл бұрын
Eric: "If I recorded everything that came in you guys would be bored." Us: "We watched you solder wires for three hours."
@sirich7751
@sirich7751 Жыл бұрын
Well said
@2aEdu
@2aEdu Жыл бұрын
Lol
@johno9163
@johno9163 Жыл бұрын
Could not agree more, and in addition learn something more about soldering in the process!
@glenjones6980
@glenjones6980 2 жыл бұрын
I had squealing issues on two or tree cars I owned but they stopped as soon as I got divorced.
@donwilson4618
@donwilson4618 2 жыл бұрын
In America at the time of this video it is refreshing and peaceful to watch someone work who has self-respect and honor.
@rider547
@rider547 2 жыл бұрын
For some reason I never get tired of watching you do these brake jobs. I think it’s because how detailed you are in every step of the process. Thanks for another great video!!! 👍🏻👍🏻
@jtjones4727
@jtjones4727 2 жыл бұрын
After watching Eric O. do these brake jobs, I have improved my own brake service procedures. If ever there was a mechanic whom was worth emulating, Eric O. has to be at the top of the list.
@FleaMarketJohn
@FleaMarketJohn 2 жыл бұрын
Detailed to perfection and that is the HIGHEST compliment to South Main. Went to an online auction in Indiana PA and another guy was wearing a SMA T-shirt ♥️♥️♥️ We all agree Eric O is the best and his family.
@andreipiv
@andreipiv 2 жыл бұрын
Detailed but also fast and smooth
@VDPEFi
@VDPEFi 2 жыл бұрын
@@jtjones4727 completely agree, some of my methods and products etc have changed for the better after seeing Eric's brake jobs, in the UK we have a very similar rust situation so many of those techniques have been a blessing too
@corvettebob96
@corvettebob96 2 жыл бұрын
Same here. I thought I was good as a dyi but I am still trying to improve after watching EricO. Drums and shoes are still my favorite puzzle to solve!
@I-watch-at-2x
@I-watch-at-2x 2 жыл бұрын
I will never understand how you haven't made it to multimillion subscribers. Mr O, you really are the best.
@malware_in_tn9008
@malware_in_tn9008 2 жыл бұрын
I’ll never understand how Scotty Killmenow has as many subscribers as he does. That guy is one of the most annoying so-called mechanics on ewetoob. Eric? I’d love to have a beer with Eric and be his apprentice for free, if I could afford to.
@brianmason8400
@brianmason8400 2 жыл бұрын
I know, right! At least a million. Matt, at Matt's off-road recovery has over a million subscribers.
@alex1949
@alex1949 2 жыл бұрын
As a Southerner, I've only seen/heard of rustjacking on KZbin. But I have NEVER seen it on a brake pad. With the glues used between the backing and friction material, I didn't even think it was possible. Mad respect to those who work on rust belt cars!
@mysketchbook3402
@mysketchbook3402 2 жыл бұрын
Yeah I'm from South Texas and it's rare but if they live in the coast or the cars are from the coast, you'll see it. Also if they were serviced before at a cheap tire shop that has 30 USD and axle brake jobs with poor quality pads. Only it wont be rust it will be brake dust build up. Or from pad slapping on worn or mad groved rotors as well. Good video though.
@terryharvey4811
@terryharvey4811 2 жыл бұрын
I get it in Tennessee, but it's not between the pad and friction material. Usually shows up under the pad shims on the caliper mount causing the pads to NOT slide back to release completely and/or stick in the fully applied position. Causes excessive pad wear and hot spots on the rotors.
@cheesecurd100s
@cheesecurd100s 2 жыл бұрын
Seems like a normal daily thing where I'm at, for the pads to fall off the backing the second I touch them
@GoodForYou4504
@GoodForYou4504 2 жыл бұрын
Choose riveted pads (instead of bonded) if you live in the rust belt. If you go with the bonded you need to seriously keep an eye on them...
@vwwrenchie314
@vwwrenchie314 2 жыл бұрын
Those pads..as are most pads now are IM , integrally molded, where the friction material is pressed into holes in the backing plate to help anchor it.
@wallingj68
@wallingj68 2 жыл бұрын
Came for the commentary, stayed for the processes!
@bowdoin5063
@bowdoin5063 2 жыл бұрын
Another SMA job done right / If all mechanics were this good what a better world it would be 😀
@JimBronson
@JimBronson 2 жыл бұрын
If all mechanics were this good I'd feel better about taking my car to the shop rather than DIYing it. But finding a good shop with a good mechanic is such a crap-shoot.
@bowdoin5063
@bowdoin5063 2 жыл бұрын
@@JimBronson Exactly
@hanknmosul
@hanknmosul 2 жыл бұрын
@@bowdoin5063 and when you find that shop, the guy turning wrenches on Your car is a new guy with 3 more jobs to work on today. They have a lift. You have a short ceiling in your garage. It takes them 3 days to fit your truck in, you get it back in 4 or 5, and $500 or more over parts. If you could get This guy (Eric) to do the job, it would be worth it.
@kevinwells4888
@kevinwells4888 2 жыл бұрын
Great to see a man who takes such care in doing his work. Whether it's a "simple" brake job or a complicated diagnosis. You inspire us to be better.
@paulheshka7065
@paulheshka7065 2 жыл бұрын
🐑 ??
@kevinwells4888
@kevinwells4888 2 жыл бұрын
@@paulheshka7065 ???
@terencejay8845
@terencejay8845 2 жыл бұрын
It's great to see the care given to all components. It's almost a shade-tree enthusiasts approach, where time isn't important. I paint the carriers, as he suggested and try to get it all looking factory new. Can't do that 'on the clock' in a commercial setting.
@roberttroxell4006
@roberttroxell4006 2 жыл бұрын
The attention to detail means the difference between the adequate job and the complete job. 👏
@jeremy2283
@jeremy2283 2 жыл бұрын
As a southerner; I appreciate the defining of rust jacking. I'd never heard of it. Good job Mr. O!
@michaelpressman7203
@michaelpressman7203 2 жыл бұрын
I ran into rushjacking when I used to maintain large rubber molds didn't realize what the name was called but we took the molds apart and all the plates I'd have to clean out between the inserts because it would throw the tolerances off and then the molds will go haywire make bad parts have a good day thanks you
@fieldsofomagh
@fieldsofomagh 2 жыл бұрын
After watching this procedure, I think I needs a sand blaster, a compressor, Mr nasty, a car lift, and someone to supervise for at least 5 years. Nice job Erico. Welcome to the rust belt. Josh is one busy mechanic.
@michaelpressman7203
@michaelpressman7203 2 жыл бұрын
If you don't want to invest in a sandblasty you can get rustlick at the local automotive parts store all you got to do soak your parts in it and it will dissolve the rest have a good day
@richardtidd2738
@richardtidd2738 2 жыл бұрын
By far one of the Best mechanics on the internet. Note the detailed prep work and that he does not rush the job. Great videos for the weekend warriors out there. Thank you Eric , you have saved me thousands of dollars in labor costs.
@GoodForYou4504
@GoodForYou4504 2 жыл бұрын
I love that you mentioned Fluid Film to coat unpainted metal. Very underrated step. I work on trucks and farm equipment. Fluid film, Blaster, and anti-seize are good for vehicles you plan on having around a while. 👍
@Ariccio123
@Ariccio123 2 жыл бұрын
Cosmoline is way messier but I will insist it's better!
@GoodForYou4504
@GoodForYou4504 2 жыл бұрын
@@Ariccio123 yeah, I've heard that said, but never tried it. I've hade luck with the fluid film, my grandfather just sprayed everything down with diesel fuel! That sounds crazy, but we still have running 1950"s tractors in good shape. No matter what, something is better then nothing it you live in the northeast! 😉👍
@AN-kg4ei
@AN-kg4ei 2 жыл бұрын
I always use antiseize on the hat even if it's incorrect or overkill. Rotors glide off at next change it seems.
@terencejay8845
@terencejay8845 2 жыл бұрын
I looked up Fluid Film here in the UK, and it's available (many times USA products are not ) and it's £15, $20 for an 11oz can..
@mattyb7736
@mattyb7736 2 жыл бұрын
"If you don't gave a sandblaster......" this is why you have apprentice's. They need to learn how to clean things manually like I did 40 years ago.
@jaybaker4447
@jaybaker4447 2 жыл бұрын
So trustworthy and fair. I wish all repair shop were like you. You always do the right fix. Not trying to over sell, but fixing what needs to be fixed. Great job once again.
@buannajim8091
@buannajim8091 2 жыл бұрын
Maybe not every single day, but I enjoy watching a brake job being done correctly and well. Living vicariously through Eric O.!
@JayAlfredoG
@JayAlfredoG 2 жыл бұрын
Customer states “car’s on fire, see the flames?” Eric: let me take it for a rip.
@truthsmiles
@truthsmiles 2 жыл бұрын
You make me thankful to live in the south. My girlfriend’s truck just rolled over 300k miles and it’s just starting to rust in a few places.
@ozzykrahn806
@ozzykrahn806 2 жыл бұрын
this guy never cease to amaze me
@Watchman999
@Watchman999 2 жыл бұрын
Yeah but now I have to buy a sandblaster.
@davidray3558
@davidray3558 2 жыл бұрын
Pride in your craft Sir, it's so obvious to those of us who watch you work. You're the button in the cap of HONEST AND HARD WORKING!
@CTSCAPER
@CTSCAPER 2 жыл бұрын
The sign of a good customer who trusts you. You call them and tell them what's going on and how much it's going to cost and they say, "Sounds good. Just do it."
@johnmcgowan8162
@johnmcgowan8162 2 жыл бұрын
THANK YOU !! I've been doing brake jobs on family vehicles for many years and thought I was doing OK. After watching this video I learned a lot. I can do an even better job from now on. I appreciate the way you explain and show how and why you do every little detail. Keep putting out these great videos.
@micahson3347
@micahson3347 2 жыл бұрын
Another comment too, Most of us here enjoy watching your videos, but realize you ultimately have a job to do. Don't worry about camera angles or time spent on other jobs. You do what you got to do. We appreciate the effort you make into these videos.
@larrybe2900
@larrybe2900 Жыл бұрын
I just wonder what it's like working around someone who talks to himself all the time? ;)
@VDPEFi
@VDPEFi 2 жыл бұрын
Thanks for taking the time while running your business to record this for us, I find it entertaining and oddly relaxing at the same time, I've learned a lot too, regards!
@rogern5368
@rogern5368 2 жыл бұрын
Dido !
@arth4570
@arth4570 2 жыл бұрын
Eric when you make a mistake it makes us all feel human again. really enjoy the videos, I may never catch up to the present day until I get through all the past videos. You have made a bunch.
@bigb7157
@bigb7157 2 жыл бұрын
Great video from a pro. That small community reminds me of where I grew up in North Georgia. That would be considered going to town though, where the post office, hardware store, and gas station would be located. Along with several flavors of Church houses to choose from. Just a perfect place to grow up. Thank you.
@crabmansteve6844
@crabmansteve6844 2 жыл бұрын
Sounds like where I grew up here in central GA, 30 minutes to a small town for gas or the post office, an hour or more to a large enough town to buy groceries. I absolutely loved it.
@Ken-1
@Ken-1 2 жыл бұрын
I must say, watching you grind the rust off of those hub faces is always the most satisfying part of these brake job videos. And when you sprayed the fluid film I almost lost it LOL. It's the rust belter in me
@christopheraxten7020
@christopheraxten7020 2 жыл бұрын
Always love the brake jobs how many of those have you done seems effortless but then that’s how professionals always make it look.I haven’t seen you beautiful dogs lately hope their all ok.
@DownloaderVideo
@DownloaderVideo 9 ай бұрын
Eric has the Dad attitude of doing his thing while explaining you the how and why he does it that way. I sit here and watch him for hours non stop. One of the best KZbin channels in my opinion.
@jimclifford1241
@jimclifford1241 2 жыл бұрын
There's nothing a classic brake job video to bring comfort and joy into one's day. Love every one of them. Thanks as always Eric!
@paulreed563
@paulreed563 2 жыл бұрын
The last part of putting the wheels on and tightening the lug nuts needed to be done with 'Yakety Sax' playing in the background like the old Benny Hill closings... 😂 😅 😂
@kastooMcFry
@kastooMcFry 2 жыл бұрын
There's something Zen going on, even when you do a simple brake job, Eric. Thanks!
@jemhem
@jemhem 2 жыл бұрын
Eric O is probably in the top 10 mechanics in America. Hats off to you Eric.
@josetellez1803
@josetellez1803 2 жыл бұрын
8:23 I was actually asking myself what rust jacking was, then you explained it. You know us too well
@rickh6963
@rickh6963 2 жыл бұрын
Yep, being from the south I've never encountered rust jacking before but it seems to be a thing in the PRNY.
@scottmorris1254
@scottmorris1254 2 жыл бұрын
I learned something thanks
@Ragnar8504
@Ragnar8504 2 жыл бұрын
@T.J. Kong I think I remember hearing somewhere that 1 mm of steel expands into 8 mm of rust or something along those lines, so an amazing increase in volume! Last winter I actually found a brake pad on the side of the road, without any traces of friction material and obvious wear marks where it should have been. After watching this video I suspect the pad failed from rust jacking. The one thing I still wonder is whether someone replaced the pad and then dropped it for some reason or whether it actually managed to fall off of a car while driving. The latter would be quite shocking! I live in Vienna, Austria, and rumour has it we're Europe's biggest single buyer of road salt. Cars are not quite as bad as rural NY ones because we don't have any dirt roads but bad enough. Every time temperatures drop towards freezing the city will cover everything with salt and brine, just in case. Considering how little snow and ice we've had in the last few years we've had more white winters with salt than snow.
@peterwill3699
@peterwill3699 2 жыл бұрын
Should the pads cover the whole disk area out past the edge of the disk ?
@josetellez1803
@josetellez1803 2 жыл бұрын
@@peterwill3699 not really, there is usually a little lip of just the backing, then the friction material
@JoseHernandez-lf6cr
@JoseHernandez-lf6cr 2 жыл бұрын
Nice brake work mr O
@johngassmann9581
@johngassmann9581 2 жыл бұрын
I did a couple of brake jobs for friends recently, and the lessons I learned from your videos were immensely helpful. Thanks for all you do, Eric! Edit: I used a C clamp and the old pad to push the pistons in. I think I learned that from you or Wes. Saved me from buying a fancy brake compressor.
@brianm9007
@brianm9007 2 жыл бұрын
I always use a C clamp as well. Works just fine for us DIY'ers. And on the dual piston calipers, just put an old brake pad in there to push the two pistons in simultaneously :)
@johngassmann9581
@johngassmann9581 2 жыл бұрын
@@brianm9007 yep, that's exactly what I did on my buddy's Ram.
@Mr2004MCSS
@Mr2004MCSS 2 жыл бұрын
Thats how I did it for years until I saw someone use the Lisle piston push tool and decided I had to have it. I still use an old pad on top of the piston but using the tool is so much easier and faster. I also have the dual piston version of the tool too.
@michaelpressman7203
@michaelpressman7203 2 жыл бұрын
I did a front brake job will pads and blood all my lines made sure everything was free and clean and painted have a good day thank you for all your information
@JimBronson
@JimBronson 2 жыл бұрын
@@brianm9007 you gotta be careful on some vehicles (like my Ford) in the rear that have plastic caliper pistons. A c-clamp will crack the plastic and then it has to be replaced. I still use the C-clamp but I use it on the outside before taking the caliper off, that seems to work pretty well.
@arniepries6480
@arniepries6480 2 жыл бұрын
Man I like the way you clean up all your work - I was taught that many years ago but I notice a lot of mechanics just put things back together again rust and dirty - not my idea of quality work. This makes for a lot of repeat customers !
@alexanderyoung5651
@alexanderyoung5651 2 жыл бұрын
Great work and fantastic attention to detail. I've learned a lot about getting brakes to last due to working on a lot of dirt road vehicles in Michigan.👍🏻
@larrybe2900
@larrybe2900 Жыл бұрын
Part of it is letting road friction be a part of the stopping process. When I see a light red I will not drive and then brake just to sit and wait, I try to judge when the light might change within reason considering traffic. Any friction you can utilize that doesn't come from the brakes is money in your pocket.
@mikechiodetti4482
@mikechiodetti4482 2 жыл бұрын
Nice. There's something about a brake job that brings some level of satisfaction. Good job Mr. O. Just in time for the snow, ice, sleet, hail, freezing rain, salt and all them fun winter things!
@alward9901
@alward9901 2 жыл бұрын
Not just a brake job Eric. Looks like a work out . Then a rest on the 10 minute road test.💪💪👍🛠
@michaelberry3426
@michaelberry3426 2 жыл бұрын
A thorough brake job with a brake test afterwards is always welcomed. Good job.
@Garth2011
@Garth2011 2 жыл бұрын
Always appreciated are the new set of gloves when assembling the pads on the caliper brackets and rotors onto the hubs. Folks really should appreciate a decent brake and rotor replacement process that is done in full and correct. You will most likely get a 50,000 mile smooth worry free experience every time.
@blueovaltrucker
@blueovaltrucker 2 жыл бұрын
The way this guy works, you know he has probably just about seen it all. Thanks for all your hard work.
@brianbanks3044
@brianbanks3044 2 жыл бұрын
love the air hammer trick to the rotor before taking it off....i have pounded on those things for 10 minutes before they freed up....see, even an old dog can learn a new trick
@icurt06
@icurt06 2 жыл бұрын
Letting the brake caliper hang in the air was priceless! LOL
@AcuraAddicted
@AcuraAddicted 2 жыл бұрын
I cannot imagine what questions are left to ask after such an elaborate detailed brake job video. These are the best!
@hanknmosul
@hanknmosul 2 жыл бұрын
Use OEM rotors and pads. The cheap ones will warp quickly. I try to find the original OEM parts when I can. They cost a little more, but you don't have that particular problem again for a lot of years.
@HunterShows
@HunterShows Жыл бұрын
"How much do I owe you?"
@ashleyrosevear4319
@ashleyrosevear4319 Жыл бұрын
Yes Eric, the rear rotors are worn right down to metal! We know what you mean, I think you do a fantastic commentary as you are working. You know your trade and do an awesome tutorial of maintainance proceedures. Great humour added as well, and this is your income so well done, very watchable and informative, best wishes from New Zealand...
@marklewis1750
@marklewis1750 2 жыл бұрын
I was waiting for the 'brake cleaner' segment with the rotors! no show! great videos as always Eric.
@CraigArndt
@CraigArndt 2 жыл бұрын
Nice job. Thanks for all the diagnostic videos, helping me with all the snowblowers and wiring issues with lights, heated handlebars etc. Traced a short yesterday on a buddy’s snowblower last night, thought, I’d better thank Eric, lol.
@andrecampbell691
@andrecampbell691 2 жыл бұрын
Thanks Eric 0, I've been doing my brakes on all my cars for 50 yrs, but I've learned a lot watching your videos. 👍
@senior_ranger
@senior_ranger 2 жыл бұрын
Although it went by at super speed, I did see you use a torque wrench on those wheel lug nuts. That's what I see as a pro move; rarely done in most shops where they just turn up the impact to high and hammer them home. Thanks!!
@Rhaspun
@Rhaspun 2 жыл бұрын
I noticed that tire stores had started using torque wrenches at some point during the early 80s. Back in the day if a flat repair was done at a gas station it would be hammered on with an air wrench. I think as alloy wheels became more common the use of torque wrenches became more common.
@TheAutomotiveKid
@TheAutomotiveKid Жыл бұрын
I’ve never thought of using an air hammer before to break rust! That was impressive 😄
@gunnutmike
@gunnutmike 2 жыл бұрын
Always enjoy watching a job done right. Good to see you torquing the lug nuts after you set her down. Glad I don’t have to deal with rust-jacking and all the other rust you have to deal with. Keep making great videos and we’ll keep watching!
@MrWaltjam
@MrWaltjam 2 жыл бұрын
with so many interruptions on a job I would forget what I said about the things I pointed out earlier and would be repeating myself or I would talk about it and then forget to do it. I appreciate the not only the "what" of the job but also the "why" that others leave out. I like that you do quality work, making the best of what you are given to work with and my kids can watch too. great job.
@92Pony
@92Pony Жыл бұрын
I'm always amazed at the attention to detail on something as mundane as a brake job!! Granted, brakes are very important, but I can imagine so many other folks/shops would not spend near the time/care in doing this job. Top shelf as always Eric O!!
@bill_4888
@bill_4888 2 жыл бұрын
As always, another great video. Appreciate the commentary, skill set, confidence and attention to detail. Nice work!
@alan2804
@alan2804 Жыл бұрын
This is the most manic ive seen you in all the videos ive watched so far, super high speed brake job no time to stop for a chat or a brew, then you speeded up the video, hilarious and great to watch.
@DIYDaveOK
@DIYDaveOK 2 жыл бұрын
Hey always look forward to a video, whether a brake job or an engine change. Thanks as always, Eric!
@AN-kg4ei
@AN-kg4ei 2 жыл бұрын
love the 'simple brake job' with the sandblasted brackets and mirror polished hubs... 👍
@larrygibson1515
@larrygibson1515 2 жыл бұрын
You always do a awesome job on everything you work on and I know that your customers appreciate it a lot
@richardwallinger1683
@richardwallinger1683 2 жыл бұрын
pretty thorough brake job there . super video .78 years old and still doing my own servicing .
@imacgst27
@imacgst27 2 жыл бұрын
Thank you Eric O for another great video. Man I can't believe how layed back that town is, the whole test drive had maybe 6 cars.
@ccole9080
@ccole9080 2 жыл бұрын
it was rush hour in Avoca CMON MAN ......
@imacgst27
@imacgst27 2 жыл бұрын
@@ccole9080 lol 😂
@mannywilliams6409
@mannywilliams6409 2 жыл бұрын
What surprises me the most is the condition of the backing plates they look new!
@blockbertus
@blockbertus 2 жыл бұрын
15:55 Take note, Ray. Never tap the pads in or grind down the ears. They have to go in schmoooth.
@Averna222
@Averna222 2 жыл бұрын
Yeah, I'm not a big fan of the way he does things. I won't go so far as to call him a hack but I will say he seems to have hack-ish tendencies that puts me off from watching him.
@gregrobsn
@gregrobsn 2 жыл бұрын
But Ray says that you should never hang the calipers by the brake hose, yet Mr O repeatedly let the heavy hunk of metal hang freely on that poor piece of rubber. I grimaced each time he did it.
@rjb6327
@rjb6327 2 жыл бұрын
He "thinks" it needs breaks? 😲 Not a motion wasted. 😊 Good educational video. Thank Eric .
@jesserobertson6383
@jesserobertson6383 2 жыл бұрын
I must say the first video I watched of yours was the one where you showed us how to do u-joints with a hammer and a socet 5 years ago!!! Been teaching me ever since. Appreciate the videos they help more than you know !!!👍👍👍👍
@johnoldonekanole602
@johnoldonekanole602 2 жыл бұрын
WOW ! So great to see a break job done correctly.
@av8tore71
@av8tore71 2 жыл бұрын
Watching you with the torque wrenches reminds me since I work on airplanes I have to get mine in to get calibrated per the FAA
@davidoickle1778
@davidoickle1778 2 жыл бұрын
I don't know what you charge, but you're worth every penny! Impressive work and work ethic.
@rogern5368
@rogern5368 2 жыл бұрын
Eric O, I happened to watch a very similar Brand X KZbin video and figured seeing grinding the pad frame to fit better was questionable but your excellent work ethic about how to solve the problem vs grinding a brand new part was a class act. There are many that try to emulate the best but fall short. Your a class A technician and a class act on your work ethic. Hopefully the brand X creator will see this video and mentally note the recent failure to emulate the best. BTW I know brand X watches SMA. Lastly the fore mentioned is a great guy and does a lot of great work that I respect hopefully it will get better. Thanks for what you do for everybody. Keep warm and have a Happy Thanksgiving.
@SouthMainAuto
@SouthMainAuto 2 жыл бұрын
Now I have seen really crappy pads not fit even a clean bracket but I am talking like the dollar tree brand pads.
@bobber55
@bobber55 2 жыл бұрын
Actually, rust upheaval is quite common here in Florida. I hated when trucks and trailers had to have the floors replaced. You just can lay a new sheet down. Let's not forget boat trailers either.
@ranger178
@ranger178 2 жыл бұрын
ahh nothing like a fun brake job in the morning to start the day
@davidstreling3690
@davidstreling3690 2 жыл бұрын
no mention of taking the brake cyl cap off the master cyl, have always done that to ease the caliper pistons push back easier as well
@timothyroe5020
@timothyroe5020 2 жыл бұрын
I miss the brake clean and fluid film sound effects!
@Cheepchipsable
@Cheepchipsable 2 жыл бұрын
Just make it in your head...
@BMan100
@BMan100 2 жыл бұрын
Just came from a Ray Raiman Chevy brake video to this.... its a good week...
@MrMustangMan
@MrMustangMan 2 жыл бұрын
same
@BMan100
@BMan100 2 жыл бұрын
@@MrMustangMan ARH ARH ARH *insert Tim Allen grunting*
@jimkoebel7019
@jimkoebel7019 2 жыл бұрын
Again a great video…..I appreciate you giving the odometer readings. I’m always working on old high mileage cars and like to see how long certain parts last. Thanks
@JPAutoService
@JPAutoService 2 жыл бұрын
Try a gun style needle scaler on the hub faces. It knocks off the rust, leaves a truer flat surface, gets right in around the studs, takes way less time, shot peens the surface so it won't rust as bad and doesn't kick up dust to breathe in. Plus roloc discs are expensive. I also use it on the brackets, it's much quicker than anything else.
@utahbrumley7473
@utahbrumley7473 2 жыл бұрын
Great Job as Usual! Best Mechanic work as usual that I personally have ever seen! Have learned tons watching your videos; Please Keep-em coming! Many moons back worked in parts sales and did basic mechanic work and diagnostics; have learned tons watching your methods and also the tools used. Since retiring from public service, slowly pursuing getting diagnostic equipment myself to do some small jobs; enjoy the challenge of properly diagnosing and repairing a vehicle that stumps everyone lol. Bout to purchase my first Autel. Btw, got my first SMA shirt and the quality is Excellent! My family and I always enjoy watching the videos! Your the Best mechanic I've ever seen and its also great to see a great family! You have the upmost respect and support from me and the Family! Keep the great videos coming; especially enjoy the diagnostic videos!
@70sfred1
@70sfred1 2 жыл бұрын
I appreciate your thoroughness and honesty!
@oldman9642
@oldman9642 2 жыл бұрын
I gotta say this, and it’s meant as a compliment. You and Rainman definitely hit the lottery in the marriage department. I’d probably still be married if I had found such a woman.
@TheOriginalDaveJ
@TheOriginalDaveJ 2 жыл бұрын
I thought you were going to say that they watch each others channels😉 Take your point on two beautiful ladies putting up with the antics tho🤣
@nedasher116
@nedasher116 2 жыл бұрын
All the KZbin garage car guys have great other half's
@frederickburns1739
@frederickburns1739 2 жыл бұрын
It's called team work. And the other thing is when you point a finger at someone you have three pointing at you!!!
@lucymc0191
@lucymc0191 2 жыл бұрын
theres a sobering thought rainman and eric o at the same shop ......wow what a franchise that would be ....
@tyree9055
@tyree9055 2 жыл бұрын
@@TheOriginalDaveJ I'd say the antics are the key to their success. 🙃
@jimwinchester339
@jimwinchester339 2 жыл бұрын
Wow - I never knew that Chevy trucks have a combination disk/drum service/parking brake in the rear. Actually seems like a pretty good idea.
@joeacfalle2380
@joeacfalle2380 2 жыл бұрын
Ohhh nooo… a brake job, without the famous “brake cleaner”. Say it ain’t so😢😂😂😂
@flagmichael
@flagmichael 2 жыл бұрын
I bet he cleaned the rotors without us. This is what it sounds like when doves cry.
@markblix6880
@markblix6880 2 жыл бұрын
Glad to see the fluid film/blaster. I'm not a mechanic but after sledge hammering aluminum wheels off my pickup, I decided a lil schmear o grease couldn't hurt.
@goodtimes2654
@goodtimes2654 2 жыл бұрын
Eric detailed quality work as usual. One thing remember is to use your PPE (eye and mask protection) when doing work around metal dust / chips or brake dust. Yes it can be a pain in the ass, but it is better than COPD or worse. You can aways voice over what you think your audience can't hear while reviewing your videos. Family first includes you! Otherwise keep up the good work and the great videos.
@VGrimm3747
@VGrimm3747 2 жыл бұрын
There are days I envy you as I miss working on cars all day. Regardless of whether it was a simple break job or a complex transmission change.
@rangerup1804
@rangerup1804 2 жыл бұрын
I want this guy to do my brakes when I need them replaced. Very detailed work.
@fredbeor2299
@fredbeor2299 2 жыл бұрын
As A retire truck mach. I love what you do with being the right way
@bigfootemobileauto9734
@bigfootemobileauto9734 2 жыл бұрын
Excellent informative job once again Eric thank you! I noticed you put a lot of time in editing the videos also. I wonder how long that takes for you or if you have someone else do it? I appreciate the cool fast forwarding jobs, that was funny! Learned a couple things also, thank you again and hope you and your family are doing well... many blessings!
@larrybe2900
@larrybe2900 Жыл бұрын
Some say it can take a few hours depending upon the program used.
@shopguy779
@shopguy779 7 ай бұрын
Awesome to see another "like minded" technician out there when it comes to thoroness and attentiin to detail. Thanks for sharing man!
@RCichard
@RCichard 2 жыл бұрын
Hey man, love the channel and all your content - you seem like a honest, down to earth, and all around great mechanic i wouldn't hesitate taking my personal cars to _(if i cant do it myself haha)_ and that says alot!
@nosonf0204
@nosonf0204 2 жыл бұрын
I've been wire brushing for years....never thought of that, thanks. Never to old to learn.
@windnh2ojim
@windnh2ojim 2 жыл бұрын
You make it look sooo easy. King of multi tasking! Stay warm and Happy Thanksgiving to you and your family.
@carlkraus6034
@carlkraus6034 Жыл бұрын
Nothing like watching a relaxing brake job on the internet.
@joesilverbliss1721
@joesilverbliss1721 2 жыл бұрын
Eric. What type of grease do you use on the caliper brackets? I have to do my front brakes on my Silverado today. This is an excellent video! Thanks Joe
@johnh8268
@johnh8268 2 жыл бұрын
I think he uses Sil-Glyde sold at NAPA (Not a sponsor). Edit - Look at his post below. Seems like he's using something different today.
@thecastros9104
@thecastros9104 2 жыл бұрын
Seen Eric O. do bunches and bunches of brake jobs, I never get tired of it.
@malware_in_tn9008
@malware_in_tn9008 2 жыл бұрын
Eric, I would love to see a REAL “Day in the life” video of a typical full 10-12? hr day in whatever speed you used to put the tires back on in this one (3x, 5x, ?x). Just mount the camera above the corner farthest from the office door to see most of both bays and let it roll with no commentary. Maybe a clock in the shot so we can gauge the time passing. Minimal processing so it’s easier on you. Just an idea. Always love to come along with whatever you’re willing to share. Happy Thanksgiving.
@davidstreling3690
@davidstreling3690 2 жыл бұрын
liked the idea about letting the air out trapped behind the caliper pin boot, have never worried about it myself
@FortunateJuice
@FortunateJuice 2 жыл бұрын
Your videos could use more shop kitty, please and thank you.
@jimthomefan50025
@jimthomefan50025 2 жыл бұрын
I used to get customers that would come in and say the car is grinding. I'd ask how long it's been grinding. Usually they say a day or two... upon taking the tire off, the brake pad is gone and the rotor is worn down through the fins and half the piston is eaten away. Early lesson learned, customers sugarcoat it figuring it will make it better. At that point, I have to sell them pads, caliper(s), rotors and new hardware. If they catch it when the wear tabs start making noise it would save them soooo much money. I kinda miss doing this work for customers, but now I work on locomotives, fortunately, they font have rotors and calipers 🤣🤣🤣
I'll Never Show You A State Inspection
22:42
South Main Auto LLC
Рет қаралды 411 М.
When To Call It Quits...
18:11
South Main Auto LLC
Рет қаралды 758 М.
Quando A Diferença De Altura É Muito Grande 😲😂
00:12
Mari Maria
Рет қаралды 45 МЛН
人是不能做到吗?#火影忍者 #家人  #佐助
00:20
火影忍者一家
Рет қаралды 20 МЛН
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 61 МЛН
Now I Did It! I Snapped Off A Speed Sensor In The Rear Axle!
17:28
South Main Auto LLC
Рет қаралды 233 М.
Ever Since The Boyfriend Changed Her Brakes....
35:33
South Main Auto LLC
Рет қаралды 698 М.
DIY Brake Replacement for 2011 Lexus RX350 - Save Big $$
19:54
Tool Time John
Рет қаралды 297
Customer Says He Can't Get The Rotor Off!
13:51
South Main Auto LLC
Рет қаралды 1,1 МЛН
Dealer Says “In the Red" ($700 Brake Job) GMC Yukon 5.3 6.2
45:43
Rainman Ray's Repairs
Рет қаралды 260 М.
Customer States (Best of March & April 2024) | Just Rolled In
13:52
Just Rolled In
Рет қаралды 1,6 МЛН
Toyota Tundra: Crank, No Start
29:40
South Main Auto LLC
Рет қаралды 362 М.
I Thought I'd Seen It All And Then This Chevy Got Dragged In....😂
35:58
South Main Auto LLC
Рет қаралды 1,8 МЛН
(Pt 1) $10,000 PARTS CANNON....Runs Like GARBAGE! (Chevy 2500HD V8)
31:48
Pine Hollow Auto Diagnostics
Рет қаралды 166 М.
Even The Kia Dealer Couldn't Fix It!
31:13
South Main Auto LLC
Рет қаралды 1,4 МЛН