Cylinder Disassembly & Repair for D8 Dozer | Machining & Welding

[@CuttingEdgeEngineering]

We hope you enjoyed seeing this job from start to finish! There was a lot going on so let us know in the comments if you have any questions 😎👍 Subscribe and hit the bell icon to turn on notifications so you don't miss our weekly uploads. 👇 🤳 Follow us online here: Instagram instagram.com/cutting_edge_engineering Facebook facebook.com/cuttingedgeengineeringaustralia/ Official CEE Merch shop: www.ceeshop.com.au

[@Murphyslawfarm]

So the world is short of good rods glad I love holes then 😂😂🤣🤣😂😂🤣🤣😂😂

[@Murphyslawfarm]

@Mr. Avuncular G'day Oregon

[@CuttingEdgeEngineering]

@Mr. Avuncular loving it, ordered some more tool holders it's a keeper!

[@АликДоронин]

Возьми меня к себе на работу

[@NuclearSavety]

How can you bend the rod but keep the cylinder straight? ....

[@PelicanPines]

I would enjoy an extended "Blooper Video"... something that could be looped at night before bed.

[@raulc398]

You are the Man!!Cheers from Toronto Canada!!

[@somerandombaldguy5296]

Most of your videos should be required viewing for machining and welding classes in either high school or colleges. The way you break things down into readily-understood terms and provide context for what you're doing would be invaluable for newcomers in the engineering fields. It's probably one more reason your customers come back: if you can honestly and clearly explain how why you're going to do a job a certain way, they'll be more understanding and less reluctant to agree to the cost. That in itself is a valuable 'soft skill' to possess and goes a long way to keeping your business viable. A tip of all the hats to you and yours.

[@CuttingEdgeEngineering]

cheers mate thanks for sharing your thoughts!

[@wwsuggs2857]

Our american't skools...are falling way short on teaching the fundimentals And mechanica

[@wwsuggs2857]

Mechanicals Required by todays standards...In the early 60's i had printing , woodworking, metal shop and electrical. Plus 4 semesters of technical drawing...pencil. pen and ink on velom sheet... all now lost in time... Shame is on skool bored unions not parents.

[@Free-j3t]

Just unbelievable the professionalism and extensive knowledge you have. I bet you’re a damn good operator too. Also the filming and editing is perfectly done. Some may say the stars have aligned for you two. But in my opinion it’s hard work, intelligence and determination.

[@CuttingEdgeEngineering]

thanks very much with both appreciate the comment!

[@JohnH20111]

i would add a serious Attention To Detail and serious Pride In Workmanship

[@ColKorn1965]

I've been a machinist/toolmaker for 37 years and just watch this for the dog.

[@CuttingEdgeEngineering]

😂👍

[@ScottGroome]

The amount of stuff I've learned about random heavy machinery from these videos is awesome, such great content

[@CuttingEdgeEngineering]

Glad you like them! More to come!

[@steveisjoseph]

Homeless lifts my spirit every time! You're a champ Homey!

[@johaanmikiel3749]

Another great job Curtis although it has to be said Karen's editing makes you look so smooth and professional. Really enjoy these, keep up the great content guys.

[@CuttingEdgeEngineering]

She agrees 😂 and thanks for watching mate glad you enjoy it

[@pbysome]

I think it's Kurtis that makes him look smooth and professional 😉

[@brettallport1250]

Behind every good man , is a great woman, teamwork and hardwork also count for much, great job, congratulations.

[@johnoliver9885]

Totally agree these presentations are totally professional.

[@KaiHenningsen]

@@pbysome Let's just say Kurtis makes it look professional, and Karen makes it look smooth 😀

[@matthewforrey9956]

As a machinery mechanic, I appreciate all the explaining. I love the learning that I am doing by watching your videos….Thanks

[@mikes78]

I'm no machine shop operator and do sort of know one end of a spanner from a screwdriver. But with watching these videos I'm starting to recognise the different tasks that need to be done and have started to say to myself "i bet that he'll do %thing% next". Sure enough, 90% of the time i guess it correctly, so I think I'm learning a little here, which I am quite happy about.

[@carl4323]

The best part of the repair was the barrel wiping tool: A length of PVC pipe with a towel duct taped onto the end! What are the two main tools of a man's repair kit? Duct tape: If it moves and it shouldn't. And WD40: If it should move and it won't.

[@CuttingEdgeEngineering]

heck yeah mate that's how we roll 😎👍 thank you to Karen for the donation of the towel LOL

[@georgenahodil23]

@kentuckyken keep your stick on the ice.

[@CGT80]

I also use duct tape for things that are stuck! Do you ever get tiny metal slivers in your fingers? I do, so I push my fingers against Gorilla tape and it removes dirt at first, even in the grooves of finger prints, and then I can see the slivers and usually the adhesive removes them. Sometimes it takes a few tries and angles, but the slivers are so small that it is hard to get them with tweezers and often times the duct tape is closer.

[@buscador2007]

Best part is, no "experts" commenting and negatively criticizing your videos. You know what you are doing, greetings from Texas, USA.

[@CuttingEdgeEngineering]

Cheers mate! We appreciate our viewers and community for the great support, armchair experts or keyboard warriors are always welcome to have a go 😂👍

[@x19fan1]

One of my favorite things about your videos is how, when you rig heavy parts to move them around, you always seem to find the perfect center of gravity such that the part hangs level and true. Either you have a great eye for the balance point, or the Mrs. is good with editing! Love the content, both of you. I teach science in the States, and regularly show your videos to my students as an example of science in the trades. (Not the outtakes, of course! Lol) Many thanks for making these videos. -Dave B

[@CuttingEdgeEngineering]

Hey Dave, i've had enough experience rigging & lifting these parts to get balance point pretty much every time. Thanks for showing some of the content to your students that's awesome. Cheers 😎👍

[@dbutler5584]

Just found your site. While reading the comments discovered Dave B same as my name! Couldn’t believe the skills you have! It would take a lifetime to learn them. Oh, I’m a retired public school teacher- D Butler, Circle A Ranches, south Texas, USA

[@MrEst1953]

@@CuttingEdgeEngineering 9

[@petermccuskey1832]

Excellent work.

[@assessor1276]

It is always reassuring when CEE videos begin with the company Safety Inspector doing his rounds.

[@dcolb121]

Being retired, I sometimes forget what day it is. Your Friday videos reset my memory. And they're informative and educational. Then there's good ole Homie. Not to mention the bloopers...

[@CuttingEdgeEngineering]

Thanks for watching each week. Karen might just do a mid week video soon to mess up your days of the week 🤣

[@tomelder6028]

Amen...I have th3 same problem...I need a calendar not a watch

[@juggernautxtr]

the same boat😀

[@joel231]

Another great video Kurtis and Karen !

[@CuttingEdgeEngineering]

Thanks again!

[@BruceBoschek]

Friday always brings a joy with these wonderful videos. I love the meticulous and methodical approach you use to rebuild these rods and cylinders. Seeing the fit of that spigot is really satisfying. Thanks, too, Karen for the excellent videography! This is my last day in the rehab clinic. I came in here in a wheelchair four weeks ago and yesterday was able to walk 3 km without help. It has been a struggle, but definitely worth it. I'm grateful for the excellent medical and therapeutic help I received.

[@williamthomas9463]

Praise God for your healing! May He comfort and strengthen you in the days ahead.

[@CuttingEdgeEngineering]

Hey mate glad to here your recovery is progressing, sounds like you have been in good hands there. Hope you continue to feel better Bruce. Take care!

[@Ottedikkie]

Thank you for bringing memories to my dad. He passed away four years ago. He repaired big machines like you have to repair.

[@CuttingEdgeEngineering]

RIP to your dad, glad this brings back some memories for you

[@Ottedikkie]

@@CuttingEdgeEngineering me too 🙂

[@jgonzo1995]

Two exemplary craftspeople at work: Curtis's machining and Karen's videography! Your content is so good that it invariably ruins the next day for me, since I can't help but to immediately watch your videos when I get a notification that a new one has posted - which means I am up until 4 am here in the States!

[@CuttingEdgeEngineering]

Hey mate comments like this are really encouraging for us to keep making these videos, it's awesome to know the videos are enjoyed that much. Cheers! 😎👍

[@jgonzo1995]

@@CuttingEdgeEngineering - You're welcome, but the pleasure is all ours. Wishing you, Karen, and Homie the best from Cleveland, OH, USA!!

[@Stefan_Kawalec]

That thread cutting of yours always amazes me. I think it's time to buy Karen a welding camera; those shots would be magnificent.

[@CuttingEdgeEngineering]

Hey Stefan! Karen is going to look into one of those now 😂👍

[@Stefan_Kawalec]

​@@CuttingEdgeEngineering To be clear I didn't mean that inspection-grade gear for gazillions of dollars (unless you'd need one). Just some lower-end, but welding-dedicated camera. I think anything may be better and easier to use than a shade glass. I mean if Karen invests her time in filming, that way she could get much better effect for practically the same effort. And of course we would get even more amazing video takes.

[@lathemachinee]

Great job Kurtis. I work to with a lathe an milling machine in Portugal, and I like see our vídeos. Very good vídeos! Greetings from Portugal

[@CuttingEdgeEngineering]

Awesome mate thanks for watching, respect to you!

[@ShainAndrews]

What manufacture is your lathe? I always like hearing which manufactures are in a country.

[@lathemachinee]

@@ShainAndrews I have a lathe shop and I make and repair machine parts, cars, motorcycles, boats, etc. Go to my channel and watch my videos. Greetings from Portugal kzbin.info

[@henrymichaelwilson8107]

Thanks very much for the Entertainment we appreciate what you do. You your girlfriend and that lovely little dog.

[@theclosetcarpenter7172]

I love that you guys are making longer videos. I never get tired of watching your videos. I've watched every single one 2 or 3 times each to pacify me while I'm waiting for the next video. I'm addicted to you channel! =-)This one is really cool. Different than what we're used to watching. Kurtis' job is cool AF! Always something different and he gets to use different tools all the time. Love you guys and I especially love Homie! I want to hug him so bad!

[@CuttingEdgeEngineering]

hey mate, welcome to the #CEEAddicts club where just 1 video isn't enough 😂 Glad to know you enjoy the content!

[@youwillneverguess]

I can't believe how professional she makes you seem with the edit. The reality comes at the end! No judgement, I curse and yell my tools too. It's part of the process.

[@CuttingEdgeEngineering]

lol yeah the "real" workshop comes out at the end, would be good to leave it all but Karen is worried about youtube strikes 😂

[@BobOBob]

@@CuttingEdgeEngineering reminder: April 1st is a Friday coming up VERY soon, and perfect timing for a "true" shop video, with the bowdlerizing at the end.

[@ke6gwf]

@@CuttingEdgeEngineering you should do an uncut video, leave it unlisted, and post the link in the comments lol I don't know if they will still strike it, but less likely to!

[@ElmerJFudd-oi9kj]

@@ke6gwf Good idea, and someone filming Karen filming Kurtis.

[@Binford2500]

I love that a D8 cylinder is a “small” one to you guys.

[@Aleks_Mechanics]

notification squad, Have a nice weekend!🔥🔥🔥

[@CuttingEdgeEngineering]

Hey mate! Notifications working well 😎👌

[@rotarypower84]

Here eating breakfast and watching another great video for some reason I knew you were going to used the torch to get that bolt out!

[@CuttingEdgeEngineering]

good one mate!

[@boagart]

Really enjoyed hearing what each seal did, I've never heard it all explained individually as people usually just refer to lot as the seal kit. Great stuff as usual.

[@CuttingEdgeEngineering]

Thanks for the comment glad you enjoyed it!

[@jtg2737]

My most anticipated KZbin channel. Hello from the State of Texas!

[@CuttingEdgeEngineering]

Hey mate, we hope to visit Texas one day!

[@sadmule]

Getting a "whole new rod" sounds like a nice upgrade for someone with a bend in theirs.

[@CuttingEdgeEngineering]

We agree! 👌

[@grotevin]

When you know how to use the bend properly it could be a selling point ;)

[@Ashley.0000]

@@grotevin Selling it to measure Bananas

[@jamieyz]

A bend is ok. If it starts weeping fluid, then you need to see a professional.

[@Onceayoungidiot]

Lovely "that's not a wrench..." moment at the beginning! 😂 Great job as ever, folks.

[@calebc6028]

I love how you say they are capable while still bringing you work, that’s a real man right there everyone. Take notes all you ‘nobody can do my job’ men, you could actually learn something here.

[@jacksrbetter1870]

Kurt/Karen you folks ROCK, Homey is Awesome as well! Stay safe, Stay Healthy, most importantly stay FREE! Saying Hello from Florida USA.

[@CuttingEdgeEngineering]

Thanks mate hope you're doing well over there

[@LJbradbury]

Love the improvised giant cotton bud used the clean the cylinder out.

[@reinokotze]

i really enjoy watching your vids. Burnt out at work and booked off about to lose my salary and not job opportunities for engineers where i live. The joy of making things and watching people make things makes me feel happy, one of the few things that still make me feel that way.

[@CuttingEdgeEngineering]

Hey mate you know what the say, when things are looking down only way to go is up. Glad you enjoy watching our vids you take care

[@dewardtaylor4192]

Love the video Curtis,Karen’s laughing is priceless and Homeless is such a happy doggo and absolutely beautiful

[@CuttingEdgeEngineering]

thanks for watching 😎👍

[@zachsmith98]

The way the smoke wraps around the rod as you’re threading looks really cool!

[@robertlark7751]

You blew me away with your method of storing your copper inserts for the chuck jaws. New project coming up.

[@CuttingEdgeEngineering]

Good stuff 😎👍

[@StewartLB9424]

Awesome timing, I was just looking for a video to put on to fall asleep to!

[@CuttingEdgeEngineering]

Sweet dreams 🤣👍

[@guerro327]

I think the pup needs he’s own channel lol. Such a handsome fella

[@CuttingEdgeEngineering]

we would lose all our subscribers 😂😭

[@mpfeffer100]

Your hard work and drive for success is truly admirable. Keep up the hard work and all the best in the year ahead!

[@CuttingEdgeEngineering]

Thanks mate appreciate it!

[@busman2000]

Thank goodness for my regular Friday night entertainment from Cutting Edge Engineering , as TV over the puddle is really boring at present. Have fun with your pineapple Homeless.

[@steveo4048]

Here in Canada, I repair cars for a living and am inspired by the way you guys fix and fabricate heavy equipment. While at work, I often am reminded of how you approach problems and systematically deal with one issue at a time until the job is done. In the end, the work is as good as new, if not a bit better. Your attitudes and commitment (in front of and behind the camera) in the work you do is refreshing and a pleasure to witness. Keep up the great content and I wish you both the greatest of success in your endeavors.

[@markusvohburger5900]

Greetings from Bavaria. Your Videos are getting better from week to week !

[@CuttingEdgeEngineering]

thanks mate!

[@70chvlSS]

Great content mate! A shit ton of great information for everyone around the globe! Heavy equipment rebuild and repair takes more knowledge than anyone really understands. Keep up the great work!

[@parmowaelo4229]

It's my dream to have my own shop with fully complete tools..... Great job .....

[@TomokosEnterprize]

HI ! Having tat dedicated cyl tie down bench is such a blessing. Those big nuts were almost impossible to break loose. I remember a feller buncher boom cyl that we had in the 50 T press with a 12 foot snipe and 10 of us bouncing on it and only managed to break 2 standard 3 1/2 inch regular sockets. We ended sending it to the town north of us to break down. I eventually made our own V groove piece I could move in and out as I needed. I never really tire of watching you do what you do so well. Seeing the chips form and fall away was a big part of my life now gone. Thanks for bringing back sooooo many great memories of days long passed my friend. Take care eh.

[@jonlowe8727]

Big hoses ,big pipes and big cylinders. Top content mate 👌

[@jonlowe8727]

Yeah I should say mates. I'd personally like slightly more dog Karen. 🐕 >

[@morgannelson9834]

I am in awe of the depth of your knowledge and the skill of your editor. I am continually impressed by the level of professionalism on this channel. Please do no stop making videos!

[@CuttingEdgeEngineering]

Thanks very much!

[@T-rock_chr0n1c]

I dunno why but that button insert is my fav one love seeing the chips fly off and the roundness of the cuts my ocd thanks you.

[@CuttingEdgeEngineering]

it goes hard and lasts for ages!

[@stumblinggmc6845]

Just a tip for using the big impact. When trying to loosen a tight bolt if you manually hold the socket in the direction of travel the impact blows are more likely to transfer more energy to the fastener instead of letting the socket loosely bounce around and not efficiently transfer the impact energy to the bolt. Thanks for all the tips you share, I thought I'd share a tip from Canada.

[@stephenthompson9722]

That makes sense cause you are taking up the slack.

[@kenore4003]

When the dugga dugga dugga isn't enough threaten it with the gas wrench.

[@wildturkey5838]

I'd love to see a shot of how much wire from the spool goes into the weld -- a quick before/after would be interesting. Bet it's a bunch! And the giggles make the outtakes lots more fun!

[@garyevans8116]

Another good job mate. Well done. Karen is good at editing to make you look good mate. And homeless is doing a good job keeping you all safe. Good work and thank you

[@FirstSuiGeneris]

Love shop-made tool; the mop! To clean out the cylinder! PVC pipe, Duct tape, and a rag! That's engineering! : )

[@CuttingEdgeEngineering]

might have to patent that one 😂👍

[@FirstSuiGeneris]

@@CuttingEdgeEngineering right! Lol

[@nickjanssens]

I can remember vey clearly watching my father doing a very similar procedure, this was over 60 years ago, a very nostalgic experience watching your videos.

[@CuttingEdgeEngineering]

that's pretty amazing, always interesting to know if the videos bring back memories for viewers

[@Redman147]

Well, I said when I got my tax return I'd buy some merch. I just ordered me a nice hand made leather wallet from the shop and it should be arriving here in Texas sometime in the coming days or weeks. I'll post up a picture once I get it. Thank you for all the great videos.

[@ocupmoc]

Kurtis so glad to see that even someone with your skills sometimes misplaces stuff, makes me feel much better about myself 😀

[@garthbutton699]

I like your style, thanks for taking the time to produce this video🤗😎🤗😎

[@CuttingEdgeEngineering]

Thanks for watching!

[@ezrhino1803]

I am always amazed at what Kurtis can do. He makes it seem so easy. The videography and editing play a big part in making this one of the best channels on KZbin. Oh and the comic relief from the safety officer doesn't hurt either. Keep on truckin guys. Cheers from Giddings, Texas..........

[@kengreenfield-nman]

Love that quick-change tool post! 👍🏻😁

[@CuttingEdgeEngineering]

Me too!

[@russmilton4491]

Another fascinating vid guys. Great production as always. Have to say the (lack of) runout on those chucks never ceases to impress / amaze me.

[@hodwooker5584]

I am an amateur, very amateur, machinist. I watch you to get ideas on how to do things in my little shop. I could watch other channels and get some of that knowledge, but those channels don’t have Homey.

[@CuttingEdgeEngineering]

awesome mate thanks for watching glad you can get some tips and tricks!

[@jamesb.9732]

Your channel has become my absolute favorite! I look forward to Friday when you post a new video. Kurtis-I really appreciate your explanations of each job, what your going to do, and why- you’re concise and to the point. Watching you work is an education. Karen- I agree with all the comments, great filming and editing! And Homeless- keep up the good work!

[@CuttingEdgeEngineering]

Hey James thanks for the great comment mate, it's awesome to know when a viewer enjoys the content and channel that much and we appreciate the support. Cheers 😎👍👍👍

[@marksd5650]

I start my Friday mornings with Kurtis and Karen. There is something very relaxing about watching the chips fly. And you make each job seem very easy. Anyway thanks much, stay safe and best regards!

[@CuttingEdgeEngineering]

Cheers mate thanks for taking time to watch

[@CuzznRickH14]

Nice work. I've got a tech here at Texarkana that does the same thing with my worn out, bent, or broken cylinders for my old Ford 4500 backhoe. Very important to get done right and quick so the machine can get back to work. I really enjoyed seeing the process done right. Stay safe.

[@CuttingEdgeEngineering]

Right on mate, sounds like you've got a good tech there 👍

[@armandtzwart9936]

One of my most favourite ways to spend a Saturday watching you're incredible craftsmanship 😁😁😁😁😁😁😁😁😁

[@CuttingEdgeEngineering]

Cheers mate glad you enjoy the vids!

[@mdouglaswray]

You always make these incredible jobs look SO SIMPLE. Thanks for another great video!

[@farmshoffman8475]

Great awesome video kurtis and Karen , great work , I’m sure the customer is very happy

[@jacobjochem]

I love watching machinists work. I never know what your up to until I've watched the entire video and it's always a pleasure watching em turn out real good.

[@acme4786]

I make it a point to learn 10 new things every day. Watching your videos I always learn something new. Today it was the "U Drill"

[@CuttingEdgeEngineering]

brilliant mate

[@medicinsider]

Kurtis makes it look so easy, is professional and informative, then at the end, you show all the problems that Carl has, great work keep it going.

[@Losttoanyreason]

Right near the end when you were cleaning the inside of the barrel before inserting the new piston, it reminded me of swabbing down the bore of a cannon before reloading. 😊

[@stevofoz]

Thank you both again for the fantastic content, it's always a good day when the notification pops up to say there's a new CEE video available! I love that Kurtis explains the components and their functions as well as the process involved in the repair. I have zero engineering knowledge but am truly fascinated by what you do and thoroughly enjoy watching your videos. Keep up the good work!!

[@henkheemskerk4437]

It is so cool to see you work and explain all

[@CuttingEdgeEngineering]

thanks for watching

[@JBLewis]

I love your passion for the work and videos! It's clear that talking to the camera isn't always easy, but I appreciate that you keep on at it!

[@randyschield2515]

Sir, you are a master craftsman. I was a machinist a long time ago. You should be very proud of your work and professionalism

[@andrzejporeda7281]

Bardzo jest świetna ta robota i elegancki pomysł i uwielbiam ten film i ten cały kanał pozdrawiam twórcę tego filmiku mile i serdecznie 👍👍👍👍

[@TYSuggested]

Love the barrel-cleaner 2000. Nice work K&K!

[@CuttingEdgeEngineering]

make sure to use your fanciest towel 😂👍

[@niallclifford5632]

Not too close unless it touches eh? Another great video guys, love what you do and glad you share it for others to see, thank you

[@interesting7906]

Kurtis makes every job look easy. The sign of a true pro.

[@Bigmike3406E]

They must have boiled a big rock up over the blade to bend that ram like that .There was a lot of life left on that trunnion gauging by the stack of shims on the cap . Thanks for sharing .

[@CuttingEdgeEngineering]

yeah not sure the back story, the customer got the machine 2nd hand and was giving it new life

[@UncleManuel]

CEE videos are like a box of chocolate - you never know which repair job Kurtis gets. 😁😎👍

[@pete1973x]

Q - How much torque on that piston retaining bolt Curtis? A- All of it! Loving the level of detail you went into on the explanations here mate, thank you - great vid.

[@RainOnThursday]

All the ones I’ve seen have been torqued by god lol

[@schsch2390]

@@RainOnThursday If Curtis weighs 80kg and the pipe+wrench are ~2 meters then 1100+ ft-lbs

[@juanmartinez-hl2dc]

Nos vendría muy bien nos hicieras mas tipos de ROSCAS ,TANTO INTERIORES COMO EXTERIORES ,O ACME. gracias por tus videos Saludos desde León , ESPAÑA

[@marcelocruz12]

Gostei do seu serviço, muito cuidadoso em sua execução, muito técnico, com todas as explicações e um serviço bem limpo. Parabéns!

[@PatrickPease]

What i like is that while i learn about the work you do, i also learn about the work that the repair needs to do too.

[@brandonbutela6269]

I just recently came across your channel and I've watched two of your videos so far and both have been great to watch. I'm a welder by trade and although I'm not a machinist I've worked along side a few good ones. You are a triple threat in the repair business for sure. Knowledge and skill for mechanical, machining and welding aspects for whatever job comes in. Looks like you have an awesome shop too. Based on other comments, seems like your wife does all the camera work and she does a great job as well. Both of you stay safe and God bless.

[@garymucher4082]

You make it look so easy while we know better. I like your LARGE cotton swab you've made... You look like you enjoy doing such work. Thumbs Up!

[@ianpendlebury3704]

When you cut internal threads, do you cut a run-out groove at the end or just watch the DRO to know when to disengage the half nuts . Just thought that I would ask a pro. Of course, nice machining and video as usual. Thanks.

[@CuttingEdgeEngineering]

hey mate I watch the DRO and disengage at the same spot each time

[@cleon_teunissen]

@@CuttingEdgeEngineering I think cutting a run-out groove is well worth the time. With the watch-the-DRO approach you will disengage *close* to the same spot each time, of course, but as the thread cutting tool is at deeper cuts: cutting for just a smidge longer means the cutting tool is suddenly encountering a lot of material at once. And then, even if you would be able to disengage at exactly the same spot each time, stopping the spindle while still cutting is hard on the tool anyway. Finally, with a groove where the thread will end there is the option of mounting the thread cutting tool upside down, running the spindle in reverse, cutting from left to right. As Joe Pieczynski puts it: that removes the pucker factor.

[@pbysome]

@@cleon_teunissen I don't see him breaking many tools and I don't see him puckering either, threading to an undercut is a good method so is watching the dro, I've seen people turn the last bit by hand crank, whatever works for the individual mate and it looks to me that watching the dro works for him.😀

[@Roy1337is1337]

I don't know why, but I got a chuckle out of watching you set the thread pitch on the lathe. Looked like you were setting her up for a hyperjump. Lol

[@MagickRoger]

Once again, a wonderful Friday night's relax with a beer with great content from Kurtis, Homeless and Giggles, the wonderful camera operator. Just one question, who does the editing of these videos? Cheers from Auckland, NZ :)

[@CuttingEdgeEngineering]

Hey mate thanks for taking time to watch and comment. Karen does all of the editing 👍

[@melvinyoung3474]

I still love the good clunk good solid steel tools when they come together.

[@MoreLaterDude]

Hi Kurtis! I am a long time 'watcher' of your videos and wanting to ask you a question. What is the worst 'workshop' prank that has been played on your or someone that you know? 😁

[@winstonviceroy6125]

While we wait to see if he replies, when I worked for a dealership, we would wait till one of the guys was on a roll-around stool working on a car, and slide an empty prestone coolant jug duct taped to an end of an air hose behind/under him. Turn on the air and watch the jug expand like a balloon and burst sounding like a shotgun. Ahhhh good times.

[@CuttingEdgeEngineering]

hey mate back in the day would always have guys putting fire crackers near ya, or putting oxy acetylene mix up pipes then lit them for a nice big bang. The usual dumb shit 😂👍

[@maurogatti57]

Well done Curtis, as usual! Your friday video is always a good relax and top intersting moment, when a war is going on 1000 Km above our head and CoVid19 pandemia still alive between us. Greetings from Italy. Go on!!! Mauro

[@alexjohnward]

Would you ever use an old bent rod to make a new smaller diameter rod for something else, or is machining through the hard layer, and dealing with scraps not worthwhile?

[@CuttingEdgeEngineering]

fair question, for our quality assurance we don't re-use damaged rods on customers jobs, sometimes save a bigger piece for a workshop project

[@jcoburn429]

Could ya make a Stein out of the Chrome bar offcut🍺,maybe? Don't know why but it's the first thing I thought of.

[@stephenthompson9722]

39:25 imagine if the massive wrench slipped off and damaged the crome ahh you would be kicking yourself.

[@shaimardanov123]

Большой привет из Татарстана, Россия, смотрю твои видео, классный канал у тебя🔥 хорошо у тебя получается восстанавливать изделия 🔥👍

[@adamludwick9931]

That's not a pipe wrench, THIS is a pipe wrench.

[@bobfraley3366]

Great job Kurt I liked the torque Wrench LOL

[@AndyFromBeaverton]

I was expecting Homeless to have the D8 Dozer Cylinder in his mouth, not a toy.

[@CuttingEdgeEngineering]

He is loving the pineapple! Won't even drop it for a treat 🥴

[@mmabagain]

I don't know why I like watching your videos. I have been an aircraft machinist for over 40 years so you'd think videos of machining and repairs would be the last thing I'd want to watch. It's probably because the majority of my time has been as a CNC production machinist. A glorified button pusher. Never did this kind of work.