CV axle ( drive shaft ) replacement ... volkswagen passat

#suspensionsystem #car #cars #fixed #fix

[@isidroguillen1019]

If you remove those 3 nuts, you'll have to do an alignment, so only the one nut above it for the ball joint needs to be removed. You won't need an alignment plus you'll save money and time.b

[@ALI_FIX12]

no sir dont need alignment after remove those 3 nuts ... Because ball joint don't move ... thank you for note and you welcome ❤️🔧👍🏼

[@richard1835]

I see the inner part separated. Thank you my friend

[@ALI_FIX12]

you welcome sir ... no its good .. thank you for watching ... do not forget to subscribe to my channel ❤️🔧👍🏻

[@gerolddo]

Ball joint didn't need to come of. Taking of the three nuts of the wishbone was enough.

[@ALI_FIX12]

ok ... thank you for note 🔧👍🏼

[@alkandrosrichards4987]

*****For the part of the axle still stuck inside the transmission, USE A SLIDE HAMMER TO SAVE LOTS OF TIME

[@ALI_FIX12]

thank you for note .. you welcome ... thank you for watching ... do not forget to subscribe to my channel ❤️🔧👍🏻

[@Eduardo-vv6lm]

What kind of slide hammer is that?

[@joelmorales3151]

I couldn’t fit the hammer with the attachment there

[@naimrivera7200]

@@joelmorales3151 24” extension have one person tap the top of the axle shaft from inside engine bay and with another person below the car pry bottom of shaft with pry bar no need to thank me

[@richard1835]

Ali my friend what size is the Axle Nut? I have to do two axles Saturday on a Passat. Thank you Ali , Richards Auto and Air

[@ALI_FIX12]

24 size ... you welcome sir ... thank you for watching ... do not forget to subscribe to my channel ❤️🔧👍🏻

[@richard1835]

Thank you my friend@@ALI_FIX12

[@user-jy4ct6st7d]

what year was this car, and what size was the axel bolt

[@ALI_FIX12]

car 2017 ... axle bolt i think 32

[@user-jy4ct6st7d]

just did mine today! mine is 2012 and axel nut was 24 12 point@@ALI_FIX12

[@abdulrahmanabdulrazzaq9396]

مرحبا علي ممكن اعرف موقعك عندي باسات يطلع بيها صوت واهتزاز ناعم يبدء بسرعة ٦٠ او ٧٠ كم/س ويكون اوضح بعد ال١٠٠ كم / س الصوت نسمي دوية بالعراقي او ونة واهتزاز ناعم بالبدي مال سيارة جيكت الميزانية والبولبيرنك ما بيهن شي اخر شي نطوني احتمالين يا اما درايف شفت داخلي او كير اتمنى تنطيني نصيحتك وموقع باي محافظة

[@ALI_FIX12]

اسف حبيبي مااكدر اعرف اذا منشوف السياره ... هذا مكاني بغداد - شارع الربيع - مقابيل الحرية - قرب مطحنة الجلبي - كراج العماد للميزانية و البلنص

[@abdulrahmanabdulrazzaq9396]

جايكم قبل واندلكم انا بالبصرة حاليا امرلكم اذا ما تصلحت هنا

[@ALI_FIX12]

مليون هلا بيك و تشرفنا بأي وقت ياغالي ❤️🔧👍🏼

[@bradking9374]

Ty sir

[@ALI_FIX12]

you welcome sir ... thank you for watching ... do not forget to subscribe to my channel ❤️🔧👍🏻

[@hayderjafer31]

From iraq?

[@ALI_FIX12]

yas 👍🏼🔧🇮🇶

[@mestizodrb3013]

No information its like baking a cake and not saying the measurements smh….Thanks to the person who asked what year this case was but this video deserves a thumbs down.

[@ALI_FIX12]

you welcome ... thank you for watching ... do not forget to subscribe to my channel ❤️🔧👍🏻

[@TylerSmithMusic1]

Doesn’t speak English most likely calm down dude.

[@mmaviator22]

If you have a baic mechanical knowledge it shouldnt matter. Most of this is all the same basic setup across every car. Sometimes you may have more than 1 control arm, sometimes the ball joint on top/btm, etc. The point is just a quick vieo showing the job, not to teach you how to do it. There are other videos that go over every socket size, torque specs etc.

[@Imtiaz717]

@@mmaviator22agree