DENON/MARANTZ ATMOS SETUP GUIDE | 5.1.2 | 5.1.4 | 7.1.2 | 7.1.4 | Emotiva

[@dandricchikote4483]

Thanks! I'm 62 and never had a fancy receiver until I recently bought a Denon X2800H 7.2 (half price btw). Didn't have a clue how to set it up. Clear directions even I could follow. You da man!

[@ealanosborne]

Hooray! So glad I could help! 😊🎉

[@cmammen]

This is absolutely the best helpful informative and straightforward hi-fi instructions for the average and more advanced guy Coming in a step-by-step digestible package. Kudos to you!

[@ealanosborne]

Thanks so much, Chris! 🤘

[@raymondayala5355]

@@ealanosborne awesome content!! Do you have a video explaining how to connect my floor stage(5 spkrs) to external amps and have my 4 height atmos speakers be powered by the Denon? Not sure if this is possible. I might need to get another external amp because of the “all or nothing” “pre amp” mode where the Denon only processes the channels. Thank you in advance for your response. I’ve been having so much trouble looking for a video explaining how to do it

[@raymondayala5355]

@@ealanosborne I just watched the end of the video again which explains my question. Thanks again for AMAZING and detailed content. 🙌🏽

[@ealanosborne]

@@raymondayala5355 Yeah, man! Choose 11.1 Amp Assign, assign the front L/R for the pre out, and then your center and surrounds pre outs will just be “on,” ready to have their signals sent to an external amp. Then the AVR’s internal amps will power the heights. 🤘

[@raymondayala5355]

@@ealanosborne thanks man! I appreciate it.

[@kevinpatrickburke]

Hay Ealan, just wanted to thank you for taking the time to shoot this vid. I took receipt of the Denon A-110 roughly 8 weeks back. I had been having issues attempting to properly set up the 7.1.6 After watching your video, I now understand the required path to take to tell the amp I wanna use two mono blocks for my main L/R fronts. After weeks of pulling my hair out (and there is not much of that left at my age) I finally get it. The A-110 is a full onboard 13.2 capable AVR but my main fronts are rated at 300W and the Denon can only reach half that, so I picked up a set of QUAD mono's with a max out of 500W. Finally I get to appreciate the capabilities of the B&W's I own. Thanks again. Yours Kevin from Glasgow/Scotland/UK

[@ealanosborne]

Kevin, it’s moments like these that make my efforts worth while with this channel. I’m so glad that I could help clear up any confusion. I had to get help myself at first, so I thought I’d pay it forward and explain what was explained to me. Thanks again for your compliments. Seems like everyone who has taken the time to comment from across the pond has been so kind. Cheers. 🙌

[@rubjim2]

Thank you very much. This was broken down so nicely for us novelists. My system is working exactly as I hoped. You are so appreciated.

[@ealanosborne]

Thank you for the kind words, Ruben! 😊

[@robwatumd]

@@ealanosborneplease give us a video about fine tuning the audio settings

[@mumeh]

Ealan, I never comment on KZbin videos, but this video was so insanely useful that I just had to post a thank you. IMHO, this is actually useful for TWO sets of people: *Folks looking to configure a complex home theater system with one of the newer receivers *Folks trying to decide which mid-high end AV receiver to buy who are concerned about how the signals are routed if they do not have enough amplified channels on the receiver Well done, and by the way, you probably saved me $500+ because I now know how I can get away with a 9 channel receiver even though I plan on powering 11 channels (I have external amps, but wasn't sure how it would let me configure them). Awesome video.

[@ealanosborne]

Martin, thanks so much! Your kind words keep me motivated to continue helping those out there getting into home theater! The film industry has changed, so we all deserve a dope audio experience when being entertained at home! 😄🤘

[@iyona14granturismogt6gtspo7]

You are the only person to show this in detail!!!! Including Philip from Sound United!!!!!!! Thank 😊 you!!

[@ealanosborne]

You’re welcome!!! 🙌

[@greenmarine5]

I have an Onkyo tx-sr494 and this video helped me so much in properly setting the receiver up for atmos huge thumbs up, My system now sounds amazing with movies and music. On another note, so glad I don't live in an apartment so I'm able to truly enjoy window shaking movies.

[@ealanosborne]

Oh nice! Yeah, a lot of the principles are the same, so I’m glad you were able to follow along, even with the Onkyo menu system! 🎉

[@jamesmiller2317]

Mission accomplished. The external amp is working (LCR channels). Later I'll check to see if those (3) internal amps are truly turned off. But for now, I'm overjoyed knowing the 3-channel ext. amp is in line, getting a signal and working. Did a quick pink noise test and while the LCR remained at the same volume level, I was able to lower the gain on about 5 of the remaining 8 channels a bit and still reach my target decibel level at the main listening area. That suggests more power is being distributed to those channels from the AVR. Based on that point alone, there has been an improvement. (Tears of happiness 😊). Thanks again for your response Ealan!

[@ealanosborne]

Hooray! So glad it’s working!

[@IanTaylor-xd9yp]

James, I have the same speaker/amp assign setup issue with my Denon AVR-X8500H with a 5 channel external amp. You say that you solved the config issue. Are you able to post the successful settings that you used? Did you the custom setting?

[@jamesmiller2317]

@Ian Taylor Yes, I used the custom setting (Assign Mode). My apologies for the slow response, but to be honest, I forgot to check the settings yesterday. I took a couple of photos of the settings if you think that would be helpful. (But, I would need an email to send them to.) The only issue I've had so far is that I've picked up a slight humm whit the external 3 channel amp in line. The humm is only in the LCR speakers. So now I need a ground wire between my receiver and the smp. Otherwise I'm still very pleased with everything.

[@IanTaylor-xd9yp]

@@jamesmiller2317 I have since tried the custom setting (Assign Mode) and set Front, Centre, Surround in the Speaker column to "None". This was automatically selected. (This covers the 5 channel external amp: Emotiva BasX A5), then Surround Back to "Surround Back", as per the terminal connection; Height 1 and Height 2 to "Front Dolby" and "Rear Dolby" respectively. This seems to work well. I don't get any hum in the speakers with this config. Is this a similar setup to what you have and have you solved the hum issue?

[@jamesmiller2317]

@Ian Taylor Yes, that is the same custom settings I used. The only exception of course is "Surround" as I only have a (3) channel external amp (OSD Nero XA3200), not a (5) channel. To hear the humm, I have to literally place my ear a few inches from the tweeter/ horn. I tried using different electrical outlets at first, but the humm only went away with the ground wire (problem solved). Otherwise, I'm very satisfied with the quality and sound of the amp. To me, it definitely made an improvement and I'm glad I made the change. I'm hopeful you'll experience a noticeable difference and are satisfied with the added amp.

[@arielstereo5484]

Amp assignment is a must prior to Audyssey, but there is no need to set the crosovers, speaker size prior because Audyssey will take care of all that. The changes happen manually after running Audyssey if needed.

[@rafacq]

I learned the hard way!

[@captainsplash24]

You are very knowledgeable and the way you explain is so engaging (and funny ) that things become much easier to understand. Thank you very much!

[@AM2PMReviews]

This helped me a lot I originally set up my Klipsch 5.0.2 system with my Denon 760 H AVR but I set the front Dolby up firing speakers accidentally to high wall mounted Dolby speakers. So I couldn’t really hear them cleanly. Now it’s way better and I put some extra db on the center channel and it’s way better.

[@ealanosborne]

Hey that’s great! Glad I could help! 😁🤘

[@lordwalthour3229]

Wow this is the exact setup I am upgrading to! The Denon and the Emotiva for my front and center speakers which are Paradigm Studio 100's. You probably saved me hours of configuration setup! This is one of the best videos explaining why to select small speakers so you adjust the crossovers. Great explanation on setting up all the speakers. Thanks Again.

[@ealanosborne]

You’re very welcome!

[@lordwalthour3229]

@@ealanosborne I have a question that I could not find in your other videos. I have an apple tv 4k and a Roku Ultra box. I have a projector that does Not support ARC or EARC. I have upgraded my HDMI cables to 2.1. I plan on purchasing the Denon which supports EARC. Can I get Dolby Atmos and other Lossless audio from my streaming boxes without having an EARC connection on my projector?

[@ealanosborne]

@@lordwalthour3229 As long as you’re plugging your streaming devices directly into the Denon, ARC or eARC won’t matter, since you’re basically using your projector only for picture, not sound. 👍

[@lordwalthour3229]

Thanks Again Ealan! I thought that might be the case I just could not find any info anywhere on how it works. So in other words the apple tv has the decoding build into the box and all the HDMI inputs on the denon will decode them straight from the apple tv or roku. Thanks!

[@Ausseke]

" that was my cat " could have fooled me , I turned around and thought " How did my cat get back inside? ". Great video, I have a Denon AVR-3700 and I never thought to go back and check the settings after running Audyssey, I am so glad I did . :)

[@ealanosborne]

Yeah, I learned that the hard way. “Wait, why does something seems slightly off now? …Damn you Audyssey!” 😄

[@montrealdennis121]

Ealan, I have an 8500 HA Denon with 10 in ceiling speakers. I have my LCR driven by a 3 channel bryston. Can’t seem to set it up properly. Could you do a video please. Thank you. Great videos!

[@MrMtr999]

Thank you sir for this video! This is the best explanation on how to setup and configure speakers ever. The small speakers configuration is priceless, people still complain why they have no bass in their system need to watch this video about crossovers . I bet a ton of people still configure large and have no bass! Thank you so much👍

[@ealanosborne]

You’re very welcome! 🙌🤘

[@Wibb14]

I just bought a DENON and this is an amazing breakdown of the different configurations for speaker setups. I so needed this video! Thanks!!

[@ealanosborne]

You’re very welcome! 🤘

[@SidVidZid]

Your sense of humor is 👍🕶😇

[@ealanosborne]

Haha, thanks! 😄

[@cableguydan]

Thanks Ealan. My BasX A3 is due for delivery within the hour, so this is perfect timing. :-)

[@ealanosborne]

Whoa cool!!! 🤘

[@brents.2501]

This is the best video guide for connecting an external amp. I have a Denon X4700h and just got a BasX A3. This is perfect!!! Thank you!!

[@saqibjaved3376]

I am just getting into dolby world. After watching bunch of videos, i found you sir the most to the point and easy to understand. Kindly help me to manually calibrate 5.1.2 with my denon avr x2500. I dont have audyssey microphone.

[@briankuhn7100]

Great information. Wish you would of kept going. Showing the cable/tv hookup and connections.

[@chrisbakerphotography4017]

I resorted to the manual and got very confused. Thank you so much for this video which makes it oh so clear now.

[@ealanosborne]

Ah, that’s great to hear! Glad I could be of assistance! 😀🤘

[@robwatumd]

Ealan, thanks so much for your content, you’ve accelerated my learning curve dramatically. Could you do a video on fine tuning the audio adjustments of the denon, MultiEQ, surround modes, parameters, etc.?

[@ealanosborne]

I’ll see what I can do! 🤘

[@AZNAV8R]

Hey Ealan, most informative video I have come across as far as speaker setup for the Denon receiver. I have recently ordered the DENON AVR S760H to replace my current receiver in my home theatre, though I cannot figure out what would be the best speaker configuration to go with in settings. My speakers are installed as follows in my theatre: 1 Sub 1 Center Front in wall speakers Mid Ceiling in wall speakers Rear in wall speakers Two option dilemma: Option 1: Set ceiling speakers as the Surround Speakers L/R and set the rear speakers as Surround Back L/R Option 2: Set ceiling speakers as Top Middle L/R and set rear speakers as Surround Speakers L/R I have been racking my head on this and your video is the closest and best I have found to solving this dilemma. Thanks and keep up the great work! Subscribed!

[@troypham]

Youre awesome mr Osbourne. I am trying to figure out how to do the amp assign on my denon 6700 and I searched youtube and saw your video. Very detailed explaination coming from you even, better than Denon technical help themselves, and I understood how to it up. You dont sound like a broken record at all because I would have rewind and listen to you explain it again anyway. Thanks again Mr. Orbourne. Tri Pham from San Jose, CA

[@ealanosborne]

Awww, that’s great to hear. Thanks for your kind words. 🙌

[@jforero28]

I have a Marantz 6011 and just got the basx a7. With a 7.1.4 setup.. this is the exact video I’ve been looking for!! Thank you!!!!! I can’t wait till I am able to hook everything up

[@ealanosborne]

Woohoo! What a setup you have already ! I’m so excited for you!

[@Ruben-zz3ph]

Been having this Denon - AVR-X4700H for about 3 months and I just got my 9060 Def tech home theater system almost done just added 2 rear sound speakers deftech 800 just missing my atmos ceiling firing speakers this video will help me fix my setup sounding awesome it would've taken me days to figure it out on my own

[@ricohippolite3137]

Very very useful I nver knew to choose 11 channel. I'm powering 3 channels of external amplifer front left n right and center.. This helpd a bunch. Many thanks

[@ealanosborne]

Nice! Glad I could help! 😎🎉

[@nnt6315]

This is really helpful. Thank you. Can you tell how to configure two separate speakers as zone 2 to stream independently on same exact Denon model.

[@consciouswebdesign396]

Having issues with eARC with my new LG Oled and Denon receiver. Atmos works well with apple tv although using native LG apps no Atmos.

[@rafacq]

Let me join all others who have said it before me, thank you for this informative video. I recently bought an SR8015 (crazy liquidation prices) and found the speaker settings confusing as I have an EMOTIVA XPA-3 Gen 3 to drive my front L/C/R speakers and use the Marantz for the rest. I wanted to assign my front L & R to the pre outs. I couldn’t figure how to do it! I have a 5.1.4 system with my 4 height speakers installed in ceiling in a TF & TM configuration. TM because the middle heights are right above our heads. The only way I could figure out to set the in ceiling above our heads as TM was to set the front in ceiling as Front Heights (instead of Top Front). Setting the front height as TF only allows TR for the in ceiling above our heads. My question… will there be a significant difference in sound using FH & TM vs TF & TR in my settings? FYI, the Marantz SR8015 replaces a Sony STR-AZ5000ES which suffered from an annoying hiss when using 360SSM. Sadly as Sony has the lead when it comes to acoustic processing. But the Marantz has a warmer sweeter sound which I really love.

[@ealanosborne]

FH vs TF etc won’t affect the sound itself for better or worse. It’s more of a placeholder or preliminary setting. The more important factor is running Audyssey room correction, because that will get the timing and levels right, no matter where the speakers happen to be. Also to note, Auro 3D setups aren’t supported when you choose “top front” or “top rear.” But it will be supported when you choose “front height” and “rear height.” Not sure if you care about Auro 3D, but just thought I’d mention that too. 😁

[@rafacq]

@@ealanosbornethanks for the response! I appreciate the information. Thanks again for all your excellent informative videos.

[@calibre00]

Thanks man, nailed it with this one! Im no newbie when it comes to this stuff, but those Denon amp assign settings are definitely confusing... this really helps!

[@ealanosborne]

Hell yeah! No prob! 🙌

[@brianhart6978]

Thanks Ealan. Very informative; loved the paired use of the interface in the AVR to explain the set up options.

[@nekerrivera]

I’m receiving my new basx3 soon and I was going crazy thinking about how to do the configuration and thanks to this video now I know to do it. I’m so glad that I subscribed to your channel.

[@ealanosborne]

Awww, that’s great to hear! Glad it helped! 🤘

[@nekerrivera]

@@ealanosborne I have the basx7 and my rear surround speakers and four Dolby Atmos in ceiling are connected to it. But I didn’t know that I have to do that configuration to pre-amp my rear atmos speakers, I was missing so much and I didn’t knew it

[@AexoeroV]

How do you like the Emotiva BasX amp? Does your speaker sounds much better with the external amp than with the internal amp of your receiver?

[@sergioacosta9712]

You need especial Dolby Atmos speakers to put on the ceiling?

[@ealanosborne]

The best Atmos effects are when you mount speakers up high or on the ceiling. But they don’t have to labeled as “Atmos” speakers to be used as an Atmos speaker. A speaker is a speaker, so you can use any passive speaker, really. 👍

[@sergioacosta9712]

@@ealanosborne Thanks, would my Logitech 5.1 z906 system work with a receiver and then add the Atmos speakers on the ceiling ?

[@MrLetitbeez]

Thank you so much Aalan! Your input is much appreciated.

[@vashranoid]

Late to this video but I had my Denon x3800h set to 7.1 (bi-amp); followed your suggestion and it seems to be working a lot nicer now :)

[@ealanosborne]

Yay! Glad I could help! 🎉😊

[@Nick-bc2lm]

Been following along with your Costco speaker bundle, and going from there up to the 7.1.4 system. This was a great how-to video. Starting off with a 5.1.2, then as more comes in, will be a 7.1.4 final setup along with an external emotiva 5 or 7 channel amp. This was an easy to follow guide on setup. Glad I found this pretty quickly tonight while searching.

[@ealanosborne]

Nice! Glad I could help in this journey! 😁🤘

[@SuperSteamengine]

i am currently on 5.2. planning for 5.2.2 set up. Does it really worth it ? going for a Top front set up. Thanks

[@simonmarshall4514]

Thanks for putting this guide together…actually, all your videos are pretty handy as I’m just starting out! If I’ve got this correct, I need to reconfigure my speaker settings. I have a 5.1.2 setup. I’m using a pair of SVS prime elevation for rears mounted horizontally on the side wall (thanks for the SVS PE video for that tip!) and I have a pair of Dali C1’s mounted at ceiling level next to seating position as Atmos heights. But I think I now need to change the confit because on the setup screen it shows them as upfiring on top of the rears? I think you’re suggesting these need to be changed to top/ceiling. Right?!? 🤔

[@ealanosborne]

Correct. “Dolby Sp” assumes they are upward firing. You would need to assign the Atmos speakers as front height or top height. 🤘

[@philmoreton2784]

So if I configure Denon 4500h to 5.1.4 the Back channels are useless and cannot be assigned to a zone 2. That sucks

[@2525Hudson]

Wow, that made my brain hurt and i am only half way through the tutorial ...... very good indeed, can i quickly ask a question, i have speakers for a 5.1.4, but my 4 atmos speakers are in-ceiling and i have two between my listening position and the tv and i have the other two directly above my listening position, with then two rear surrounds behind me....... when you have shown the set up it appears i need to set the height speakers at Top Front, Top Middle...... but i could not see that configuration ? Just Top front/Top rear....... have i missed something ?

[@ealanosborne]

No, you’re not missing anything. Typically you’ll only use “top middle” if you have only 2 ceiling speakers you’re dealing with. Or if your AVR can support 6 height channels. Otherwise - regardless of placement - 4 ceiling speakers would still be considered top front and top rear. Although there is “SHL” and SHR” in the software for side-mounted height speakers, which you could experiment with. But my guess is it won’t make much of a difference, since in the end, running Audyssey will account for how far away the speakers are from the main listening position anyway. 🤘

[@2525Hudson]

@@ealanosborne Excellent, thank you for the quick reply. I will be buying the 4700H in the next few days so that saves a lot of confusion, along with the 4 height speakers i have two rear surrounds which are behind me but above me at height..... but not in the ceiling or as high, they are simply standard rear surrounds which you would find in a normal 5.1 system but i have an open plan lounge/kitchen/diner which is big enough to fit all this in so it's an unusual room in terms of acoustics and layout. Thanks again.

[@TheAheer]

Awesome video!!! Definitely helped me a lot with at least understanding the software. I recently have built/bought a home theatre system 5.1.1!!! I use a Denon X6700h 2 Klipsch RP-8000 towers front speaker 1 Klipsch RP-504c II center channel 1 Klipsch 12 inch sub And 2 RP-600 Surround Speakers I was following your steps and process to set up my system. However my denon does not have a "9.1ch" option. The only 9.1 options all have "SB" or "FB" in the title of the options. I do have a "11.1ch" but it doesnt make sense to select that option. Wondering if you could shed some light on this please and thank you!

[@ealanosborne]

Sounds like you have a good ol’ fashioned 5.1 system, is that correct?!

[@TheAheer]

@@ealanosborne correct!!

[@ealanosborne]

@@TheAheer Basically with the X6700H, you can get to the same result with a 5.1 system starting from several different points. Amp Assign Mode 9.1, 11.1, or 13.1 I believe all work, you just need to select "5ch" for your "Floor" and that's it, since you don't have any heights or surround backs, etc. Then back in the "Speaker Config" page, just make sure you have selected front speakers, a center speaker, a subwoofer, and 2 surround speakers. That should do it.

[@gjman1972]

Hi great video question please if you don’t mind. I just finished setting up my home theater and I’m first running a Sony A90J 65 inch OLED, my question is I’m using a Denon 3700h receiver with two Klipsch RP-800F’S front speakers and two R-41sa’s as the height speakers which are mounted to the wall on each side of the tv cause I didn’t like when you place them on top of the floor speakers and aim it at the ceiling to get the overhead affect. I also have two Klipsch RP-600m bookshelf speakers on stands as the rear and I’m using the tv as the center channel until I get dedicated center speaker, there is a 10 inch woofer as well. Now the entire setup uses hard wired connections and I just bought two Denon 150 home wireless speakers and I would like to use them as rear height speakers to make it a 7.1 but so far I’m not seeing a way in the Denon setup to add two wireless speakers it only gives options for connecting more wired speakers. So is it possible to do this? Thank you so much

[@ealanosborne]

Ah…looking at the specs online, it looks like the 150 wireless speakers aren’t designed to be integrated into a traditional wired home theater system. It can be a part of a whole house audio system for music streaming through HEOS technology, but that’s not the same. And the 150’s can be used as rear surrounds for the DHT-S716H sound bar, but not in a wired system. Just runs off different technology. Would be pretty awesome if it could be used within a traditional home theater, but the technology just isn’t there…yet? 🤷‍♂️

[@IAmJustSaying6]

Yeah, but I WANT to see a tutorial, from the 100% beginning, plugging in speaker wires to the end. Can't find that tutorial.

[@angelophilipteruel7576]

Great help! Just purchased and set up my denon 4700h yesterday!

[@calvinko805]

Thank you so much for breaking the secret on this confusing set up. Now, I have to go buy an external amp.

[@cormorant28]

Hi Elan. Great video, thanks a million. I have a Denon X3700H and a 7.4.2 configuration, ie. 2 front towers, 1 center, 2 surrounds and 2 surround backs, two subwoofers, and 4 ceiling speakers. I need an external amplifier to fire up my height 2 speakers. But I have an old Sony STR-DN1060 that works perfectly. Can I use the additional av receiver as my external amplifier? If so, how can I make cable connections?

[@ealanosborne]

Hi! Thanks for the kind words! 🤘 To answer your question, no, unfortunately. You would need a higher end AVR that is equipped with a 7.1 multi-channel input section (typically used with SACD or high end Blu-ray players that might have a better DAC than your AVR). Otherwise, you would need to get a good ol’ fashioned external amp. Emotiva BasX amps are a great value, OSD and Outlaw Audio too.

[@gordoa172]

Your video is a great tutorial and your delivery of information is awesome! Well done brother!

[@ealanosborne]

Thank you very much!! 🙌

[@Dingo-de7yu]

Excellent! Thank you once again Ealan! I'm setting up my Home Theater with a Marantz av7706 paired with grateful

[@NatarajanGanesan]

I have all ceiling speakers pre installed. Got an AVR-760H and trying to figure out connections from the bunch of wires hanging out of the walls

[@blackbond-007]

Thank you! I was wondering how i could assign for my 3 channel external amp. 🙏🏾

[@sureshbalaji6791]

Hi, Great video that answered my question. If I am assembling my amplifier from a local seller, Will I be having an option to use this interface in a manual assembling setup from my local seller? If yes, How do I specify my requirement to him?

[@96impalass10]

Great video, wish I had seen it sooner. I currently just completed installing 4 height speakers for a 7.1.4 system using the X4700H Denon Receiver and I didn't realize I needed a seperate amp for the height 2 speakers. My question is can I use another receiver, specifically a Denon AVR-1613, for the height 2 speakers? Thanks

[@ealanosborne]

No, sorry. You would have to have a higher end receiver that has one of those 7.1 input sections to be able to use it as a standalone amp.

[@96impalass10]

@@ealanosborne ok thanks for replying, I was hoping I could use the Cable audio inputs and front left and right stereo speaker outputs as the height 2 channel. well I guess I need to do some shopping.

[@TheoTsant]

Amazing video very good explanation.i have a denon avr-x2700h and 5.1.2 ley out with top front sealing speakers my tv is lg nanocel but when I am in Netflix is not showing atmos when I am using the avr only dolby vision.without the avr the TV plays atmos cos it's support it but with the avr is not is anything that I have to check my hdmi is good guality up to 8k but not sure where is the problem.thank you

[@ealanosborne]

Netflix just changed/added their pricing packages, so maybe 4K/Atmos only comes with the higher priced tiers? I’m going to look into it more myself…

[@TheoTsant]

@@ealanosborne thank you for your answer I found the problem I changed some tv settings with the hdmi output

[@junflores7143]

Hi Elan. I’m planning to build my home theater. I will be using 4 elac b62.0 for front and back and elac center speaker. I will also be using 4 ceiling speakers. And 1 subwoofer. I don’t have a receiver yet. I am mulling between Pioneer Lx505 and Denon Rz50. Can you give me advise on choosing the receiver? Thanks

[@RonaldKahan-k8q]

Hi. Great video. I just bought the Denon AVRX4700H. In the manual I don't see a connection configuration that will represent the speakers I have to connect to it. There will 5 floor speakers (FR, FL, C, SR, SL) plus 2 Dolby enabled FHR, FHL (assume connect to Height 1) but I also want to Bi-Amp the Front Klipsch 8060's, and would like to use the Height 2 connections for that. The manual shows a 7.1 channel:Bi-Amp Connection of Front Speakers in the manual, but in that configuration they show an SBR and SBL which I do not have. Is there a way to fix that with the Speaker Config. settings? Or when I hook all the speaker wires and run Audyssey, will it figure out the correct configuration to ASSIGN? Thank you in advance for any replies.

[@ealanosborne]

If I have it correct, you’re wanting to set up a 5.x.2 system, right? The software only allows for Bi-amping using the SBR and SBL speaker terminals, which is great, since you aren’t using surround back speakers at all. So you would connect the hi frequencies of your 8060’s to the front L/R speaker terminals, then connect the low frequencies to the SBR/SBL terminals. 🙌 Make sense?

[@kobaltstaub287]

I was going to buy a monolith M2100X 2 channels 2X90W (Emo's are hard to get in Canada) since what I saw in the Denon 3700X diagram was only fronts or surround back with a 7.1.4 layout, but with your video, I know I can buy a M3100X 3 channels 3X90W to hook up all the front spread to it. So I don't know if I should thank you or curse you for the difference in price lol ; ) Great video 2 thumbs up.

[@ealanosborne]

Haha! You’re…welcome? 😁🎉

[@ronalddecelis1944]

Hi EalanI got the 3700 Denon and I am adding the Basx a3 to power the front stage.My configureation is 5.2.2 for now but be adding 2 more in ceiling speakers.So how can I connect the power amp to use the preouts of the avr I saw your video and only the right and left channels are greyed out What about the center channel how does it uses the preout to the power amp.Thanks and very useful videos.👍

[@ealanosborne]

The center channel doesn’t gray out. It’s just automatically ready for a signal if you happen to plug in an RCA cable into its pre out. Just the front L/R or Rear Height need to be actually assigned if you’re using a combo of internal and external amps. 👍

[@TrogdorElite6]

Awesome instructions! Thank you!

[@ealanosborne]

You’re very welcome!

[@peterharman8466]

Hello Ealan, thank you very much for using your time and effort in making this video it's very helpful and informative but here's my question, I gave a denon x4700 h and an emotiva basx a5 I am considering a 5.2.4 and if I can I would like to add 2 back/rear speakers behind my seating position L/R is this possible with the equipment I have? I intended to power the front lcr and rear surround using the emotiva a5, is this possible please? Oh and my height speakers are nothing fancy or mega expensive they are sony surround sound speakers. Will this work? Huge thanks again for your time. Peter

[@ealanosborne]

That’s definitely possible. And at the start, don’t worry about which speakers your using for height channels, as long as it sounds good to you. 😃 As long as you use the 11.1 software assignment, set Floor to 5CH + SB, and set the Pre Out to Front, you can power your 5 bed layer speakers with the A5, and power the rest of your speakers with the internal amps of your x4700h. 👍

[@jasonwatkins4277]

Thanks for the video. I have a Marantz SR6014 and will be hooking up an Emotiva Bax5 very soon. Will be running a 5.2.4.

[@ealanosborne]

Awesome! You’re gonna love that setup! 🙌

[@gregoryotoole41]

Outstanding and informational how to. I am still confused about hooking up my Denon 3600H with my 7.2.2 setup (have 2 wall mounted height speakers). I want to power my front stage using three of the five Outlaw 5000's amps. Please help me. Thanks

[@ealanosborne]

It should be the same, if I’m not mistaken. 11.1 Amp Assign Mode. Floor: 5 ch & SB Height Sp: 2 ch Pre out: Front Also make sure Speaker Config page is correctly set to 7.2.2. Only the front L/R pre outs need to be assigned. The center channel will just be “on” and ready for an RCA cable to be plugged into it, going to your Outlaw 5000

[@gregoryotoole41]

@@ealanosborne Thank you so much for getting back to me so quickly. I had already tried earlier what you suggested but Height sp 2 channel gave me NO Pre-out: Front. If I chose Height sp 4 channel, Denon software gave me the option to keep Pre-out: Front. I only have 2 Height speakers not 4. Any additional thoughts on this dilemma? Thank you once again for your time and effort in trying to help me.

[@ealanosborne]

@@gregoryotoole41 Oh, right. Gotcha. Yeah, it’s a weird little quirk with Denon AVRs (at least from a few years ago). You still need to choose 4 height speakers to engage the pre outs, yes. But then back out of the amp assign, go to Speaker Config and select only 2 Front height speakers. So that way the AVR knows it only needs to send a signal to 2 heights instead of 4. Techno Dad also broke this down a few years ago in this video… 👇👇 kzbin.info/www/bejne/hWOVlqCEq8mpgsk

[@gregoryotoole41]

@@ealanosborne Thanks again. You and Techno Dad are godsends in helping answer questions. Do the newer Denon models still have this weird quirk?

[@ealanosborne]

@@gregoryotoole41 From what I’ve seen with Techno Dad’s breakdown of the x3800h, it’s not so weird anymore. Denon has improved the user interface so that’s it’s easier and more intuitive to perform customizations, thank goodness. 😄

[@ronniej962]

Hey Ealan! Great, great, great video btw! Excellent content and instructions. I have a Denon 4700h with a 5.1.2 speaker setup (the .2 was literally setup yesterday). I’m starting to get the feeling my speaker connections may be wrong. I have 4 satellite speakers - 2 front at the top of the wall pointing down to my listening position, 2 rear top of the wall pointing down and now 2 in ceiling directly above my position (of course the center and sub - not worried about those). The 2 fronts are connected to the AVR’s FRONT R/L, center to the CENTER, 2 rears to the SURROUND R/L and the 2 ceiling HEIGHT1 R/L. Can you advise if this is okay and if not, what changes would you make? I know it probably also depends on the config settings but I think I have that set after your video with the exception of only one height, ceiling middle. Thanks in advance!!

[@ealanosborne]

With only 2 heights, they would be connected to Height 1, so yeah - all the connections you listed are correct. 👍

[@ronniej962]

@ealanosborne Thank you for the reply! Glad you're still watching this post! You're the best! Sounds like I'm good! Thanks again!

[@ealanosborne]

@@ronniej962 Hooray!! 😁

[@ozkronos]

If I have. 5.1.4 system with surround back and no side surrounds speakers, will I be able to power all my speakers? Do I loose 2 channels by having to setup 7 bed layer speakers and then turn of the side surrounds? Great Video!

[@bigw281]

Thank u for teaching us!

[@jarihakala950]

This was perfect! Thank you!

[@ealanosborne]

You’re welcome! 😁

[@davidcochran2255]

This video was amazing mate I all can say is i wish I bought a denon av receiver I got pioneer 9.2 av receiver the settings on it is basic and shit. Lol Denon got everything in there settings that I wanted for my home theatre setup

[@planb1861]

Very helpful video. Thank you! I'm new to the home theater game. I just bought 7.2 Denon AVR but would like to add couple more channels to it. I can purchase a 9.2 AVR but the cost jump very high from 7.2 to 9.2 AVRs. any recommendations on how I can add 2 channels in a cost effective manner? thank you.

[@ealanosborne]

No, sorry. 7 channel AVRs can only process 7 channels of audio (and up to 2 subwoofers). It’s only once you upgrade to the 9 channel tier that you’ll find AVRs that contain 9 internal amps, but can process a total of 11 channels with the help of an external amp (like the Denon X3700H). Not sure why manufacturers decided to do that to 7 channel AVRs, but that’s the way it is. 🤷‍♂️

[@planb1861]

@@ealanosborne ok; thank you for the prompt response.

[@jojopri22]

Thanks Ealan for the Video Tutorials. I was in Costco last 2days ago to look for a gift to my wife. I passed by the Electronics side and saw the last 3boxes of Klipsch 5.1... Right away I looked at my KZbin and typed the Title for review and your the First Video that showed. I am not an Audio File Person. And you were right I got the package 5.1 for less than $400.00 I've been watching your Video and now I learned from you that I need a Receiver for the Set-up. I live in a Apartment ground floor. No idea yet what Receiver I should consider... Any recommendations would be Appreciated. Stay safe and Thanks again and keep making Video. Jojo

[@ealanosborne]

Denon s650h, Sony dh590, Yamaha V385 for 5 channel. Or if you want the option of 7 channels and adding 2 more speakers down the road, Denon s750h, Yamaha V6A, Sony dh790, Denon x1600h. Although receivers are hard to come by this holiday season. Sad, but true. Lots of delays and supply chain issues due to COVID.

[@bienvenidocardenas6847]

Hi. Great Video. Super Helpful. I just got a Denon AVR-4700H in a 7.2 setup with Klipsch speakers and an Emotive BasX A7. Im in the process of wiring 4 Klipsch in ceiling speakers. I will like to have the Emotiva BasX A7 to power my Front and Center speakers and my 4 in ceiling speakers. Is it possible to get this configuration? Following you video, I noticed in the Denon setup that you can only select to power either the front or the ceiling speaker but not both.

[@ealanosborne]

Hey thanks for the compliment! And yes, that is a software limitation of the X4700H, either assigning the front 2 speakers OR rear height speakers to be powered externally. I honestly wish you COULD mix and match to your heart’s content, but no. Although if it’s in your budget to get a BasX A4 as well, then you could put it in Preamp mode and power all speakers externally. But until you can do that, I would power all your bed layer speakers with the A7 anyway and let the Denon power the height channels. Depending on the content, the height channels will most likely be activated only sporadically and more subtly. So having your 7 bed layer speakers externally amped is a better way to go in the meantime. 👍

[@bienvenidocardenas6847]

@@ealanosborne Thanks a lot for your advice. It is hight appreciated.

[@sjsphotog]

fantastic. I was exactly asking while watching what about using a 3 channel amp (like the Emotive Basx A3) for powering the front stage. Great walk thru. I wish they made it easier to setup and walk thru. they need an app to do step by step. keep up the good work

[@ealanosborne]

Thank you very much! 🙌

[@jjdominguez4616]

Hi Ealan, I have 2 klipsch - R-625FA Tower Speakers, 2 klipsch rp-502s for surround back, 2 R-41M Bookshelf Speakers for surround, 2 klipsch subwoofer R-12SW, center channel klipsch R-34C, two in ceiling Speakers Klipsch CDT-5800-C II my receiver is the denon 3700, I don't know why the rear surround speakers don't do any sound when is in dolby atmos mode, it only sound when is in multi channel mode, appear assigned and make sound when I do the test sound, what do you think I'm doing wrong? Thanks so much.

[@ealanosborne]

Hmmmm...1) double check that your Denon has 5 + SB selected for your floor speakers in Amp Assign 2) double check that in Speaker Config page the surround backs are engaged and 3) make sure your source (Blu-ray player or streaming player) is set to bitstream audio out and not PCM. That's where I'd start. Not sure beyond that...

[@jjdominguez4616]

@@ealanosborne thank you so much.

[@rollsta17]

So all the adjustments and settings are done through your audio video receiver For the emotiva

[@ealanosborne]

Yes. The processing all happens within the receiver, where the Emotiva is just an amp, so its only task is to power an audio signal.

[@RakeshKumar-ve9je]

How to extend and setup proper Dolby setup of 24.1.10 without using high end preamps like Trinnov Altitude³² or Altitude Ext 48 and flagship avr, amps etc.,

[@amolr]

Amazing video!! I have a Marantz SR5013 and use BP9060 speakers. What is the best speaker wires I should use?

[@ealanosborne]

I use these and they work just fine. 👍 14 gauge preferably. 👇 amzn.to/3cmGoCP​​

[@amolr]

@@ealanosborne thanks! What AWG 12/14/16/18 to use?

[@ealanosborne]

@@amolr AWG 14 is preferred. Thicker and more durable. Although you can still get away with AWG 16 if you want to save money 👍

[@amolr]

@@ealanosborne should have waited. I already ordered a 12 awg. should i cancel those and get the 14 instead?

[@ealanosborne]

@@amolr Yes. 12 gauge is very thick. Mainly for huge speakers that need that kind of impedance to run properly.

[@cisco150]

Thanks for this I have a 5.1 system I have JBL 590 x2 JBL 580x2 and the JBL 520c ill be adding 4 top speakers soon what amp should i get to power the JBL speakers. looking at the 2 to 5 channel Emotiva amp which one should work out. I have A Denon x4300h

[@ealanosborne]

I’d maybe start with a BasX A5 to power your ear level speakers, since those require the most juice when it comes to power management. Then the Denon’s amps could power the heights just fine (when you decide to get those) since they don’t draw as much power, being used more for atmospheric sounds usually. 👍

[@cisco150]

@@ealanosborne Thanks for that im probably not listening to the speakers as they were meant to be because of under power. i will get a 5ch amp looking at the one you recommended BasX A5.

[@zelko0768]

Great info. After seeing this I realized that I should Plug my center straight into the A3 instead of Avr. Would I need to recalibrate if I do this?

[@warpathh]

You didn’t cover tuner settings like Surround Parameter, Cinema EQ, Dynamic Compression, etc. There is so much more to this…

[@robwatumd]

Please give us this videa

[@ronmarra6651]

Very very well explaned I bough emotiva basx 2 and basx 3 and didn't hear anything any better but i didn't know that the set up was so confuseing how would i set up basx 3 for lcr basx 2 for surround thank you for this very valueable lesson have the basx 3 set up but dont know how to get the 2 set up for thr surround thank you thank you thank you Ron

[@ealanosborne]

You’re very welcome, Ron! 🙌

[@cmsweitzer1]

Just ordered this same receiver! Appreciate the vid!

[@tomkrehel2494]

Great video! I have one question, which I think you covered. Just want to be sure I got it right. 7.1.4 with the front L&R and center powered by a BasX A3 11.2 5ch & SB Front Pre-outs for front L&R and center connected to the BasX A3

[@ealanosborne]

You got it! And lastly, double check the Speaker Config page to make sure the Surround Back channels are set to 2 “small” speakers 🤘

[@jamesmiller2317]

Hi Eallan. This is the video I've been looking for...thanks! I have the Denon AVR-X8500H and a 7.1.4 setup in my theater. I have purchased a 3-channel external amp that I want to add for my LCR channels. I've been through every Speaker/Amp Assign option and I can't find any setting showing a "Pre-Out" option for the left and right main. And none of the "View Terminal Config." diagrams show the left / right front connections highlighted in the "Pre Out" section Am I to assume pre-out is always there/on for the LCR channels? This is frustrating, it's my second day trying to figure this out (and I can't find the hard copy manual, to see if it would help) Any suggestions?

[@ealanosborne]

Yes, in theory, the pre outs should just always be “on” when you connect an RCA cable to it, since you are interrupting the audio signal before it hits the internal amp. Have you tried the Custom amp assign mode? I wonder if that could help with assigning the fronts to be powered by an external amp? I wish I was more familiar with that beast of an AVR, but it’s definitely more customizable than its less expensive counterparts.

[@jamesmiller2317]

By the way, I checked the online manual and it was of little help in regards to settings/ configurations / hookups for LCR external amp.

[@montanairishman]

Ealan, outstanding video! If I want 7.1.4 and go with the x6700h, is there any reason to set up an external amp at this point? Today I have 7.1 and purchasing the x6700h to get me to 4 ceiling Atmos set up. I guess I'm not sure how to take into account the watt specs of my speakers to determine when to get a 2 or 3 channel external amp.

[@ealanosborne]

Thanks for the kind words! Well, it’s just a step in the evolution of your home theater, really. Since the x6700h has a rating of 140 watts per channel (2 channels driven), so probably more like 90 watts per channel when everything is working simultaneously. So if you have speakers that work best around 100-125 watts per channel, using the internal amps should be fine for awhile. But it does make a difference to start with the front three speakers (left, center, right) being powered externally. It allows the Denon to process audio better when there are less speakers to power on its own. More details come out, dynamics are more dramatic (loud parts are louder, quiet parts are more intelligible), etc. But honestly, it’s not exactly worth it until you get more expensive speakers that need more power to really come alive. Like speakers that can handle 150-300 watts (or more!). Then you can get some external amps that can supply that kind of power to really let the speakers sing! Make sense? 😁

[@montanairishman]

@@ealanosborne Yes, thanks! I can always add an amp if needed. Great advice!

[@robertwilson9590]

Great video! This will save me a lot of time when I set up my 7.2.4 system. Just curious, how did you come up to speed on setting up yourAVR? Did you do research online or follow a manual?

[@ealanosborne]

Yeah, first I did online research, followed the manual, and even THEN I consulted with my buddy Techno Dad to make sure I understood it correctly. 😄

[@tommyboydiy1484]

Thanks. I was debating between a 5.1.4 or 7.1.2 setup. My second level of seats will be up against back wall. So I'm debating if the better setup would rear height on back wall/ceiling angled downward or 4 ceiling mounted atmos and no rear surround. Would it make more sense to have rear height or ceiling? Also would you assign the rear height speakers as rear surround in a 7.1.2 or as 5.1.4 rear height atmos?

[@ealanosborne]

Yeah, I’d go with 5.1.4 since it completes the 3D immersion with 4 heights, as opposed to only 2 heights in a 7.1.2 setup. And yes, rear heights on ceiling angled down 👍🎉

[@texxhexxmm]

I will Upgrade to 5.2.6 these days . On my Marantz Cinema 50 i have to take the surr back for the top middle? The Fronts will go into Marantz mm7025 amp then.

[@MarkSchaff]

Super awesome advice. Was wondering - I have just a 5.1 set up. My rear speakers are in the celling. (all old school stuff, I guess). What would be the right manual set up for that? Would I gain a bunch buy buying some sort of upward firing atmos speaker to set on the top of my towers in front?

[@ealanosborne]

Hmmm, well, running Audyssey is the most important part about having rear surrounds in the ceiling so that the time alignment to your listening position is correct. And you would just start with the 5.1 amp assign. And yeah, a couple of Atmos height speakers in front could very well enhance the experience! Which AVR do you have?

[@MarkSchaff]

@@ealanosborne Thanks for the reply. S750H is the one I have. When I set it up - i did automatic and chose ceiling mid - but I'm sure I'm wired for rear surround. I think that's probably way wrong.

[@ealanosborne]

@@MarkSchaff Yeah, even though they’re in the ceiling, you still want to designate them as rear surrounds so the correct sound effects come out of them. I would recommend mounting some speakers high above the TV for some front Atmos effects, if eventually want to go that route. But if mounting isn’t an option, upward firing speakers I would only recommend if your ceiling is 8 feet high (or less), and flat, with no popcorn ceiling, etc. 😎

[@MarkSchaff]

@@ealanosborne Really appreciate the advice, Thank you! What speaker output is used for the atmos speakers if I set them on my front towers?

[@ealanosborne]

@@MarkSchaff Upward firing speakers are labeled as “Dolby speakers” in the Denon software, and you typically want to have their volume level at least 3 dB more than the rest of your speakers since the sound has a longer distance to travel 👍

[@krzysztofpawaowski3713]

Denon Atmos Setup Guide is great! Thank you Ealan so much. Now, I would like to connect my Denon AVR-X4500H both to Emotiva BasX A3 and Emotiva XPA Two Gen3. As I have eleven speakers (2 front, 1 center, 2 surround, 4 dolby atmos, 2 high), the assign mode would be 11.1 ch. Emotiva XPA Two Gen 3 would support 2 fronts and Emotiva BasX A3 would support 1 center and 2 surrounds. Would you be so kind and tell me how all setups and connections should look like? Thank! Krzysztof

[@ealanosborne]

In amp assign, Floor should be set to 5 Ch + SB to activate the preout assignment. Choose 4 height channels (and choose either "front" or "top", depending on if you have mounted or in-ceiling speakers) and choose Front for the preout assignment. Go back to the Speaker Config page and make sure the diagram looks like your setup. The physical RCA cable connections is pretty simple - just plug in to Front Left, Front Right and connect those to your XPA Two amp. Center, Surround Left, and Surround Right preouts get connected to the BasX A3. And that should do it! The only preouts you have to assign are Front Left and Front Right. Center, Surround Left, and Surround Right don't need to be assigned, they're just ready for a signal if an RCA cable is connected to its corresponding preout.

[@krzysztofpawaowski3713]

@@ealanosborne Thank you very much! I followed your advise and all works great! Thanks again, Krzysztof

[@theMatch111]

Thank you so much, my house rumbles now. Just watched Spider-man NWH.

[@ealanosborne]

Gonna pick up that movie later today! And congrats on leveling up to house rumbling status. 😁🤘

[@antoniotaylor6300]

Good morning Elan, you have done great job breaking down each configuration. I purchased the Denon 6700H 2 weeks ago and my question that I have for you with my 7.2.4 setup. I'm using the 11.1 setup but for some reason I can't get sound from my front & rear ceiling speakers nor from my surround back wall speakers but when I ran the Test tone I heard sound coming through all of the speakers. I haven't ran Audessy yet, should I or is there some other issue. I'm running HDMI ARC from my to the receiver... HELP !!!

[@menacordero1]

I would like to know if you have a video for the Costco 5.1.4 reference system with the Onkyo TX-RZ50.

[@ealanosborne]

I’ve reviewed the 5.1.4 Cinema System on its own, but I don’t have a video where I connect it to an RZ-50, sorry. 😬

[@robertcathcart2560]

Great video, Ealan! I’ve got a Denon x4500h and I am going to add an OSD Nero 5 channel external amp. I have a 7.2.2 speaker configuration. Can I use the OSD amp to power my LCR speakers and top front speakers?

[@superslyko123]

So Gene at Audioholics is telling me the Denon amp has the ability to turn OFF the internal amplification, but in your example the Denon amp is still on!? I only have the ability to turn off software, not the hardware. Am I rerouting the internal power? So........... separates is the only way I can eliminate all internal amplification from the AVR? Correct? You said it yourself, bypass. Not turn it off. So the AVR is still doing all the amplification, it's just not hooked up & driving the speakers. What am I accomplishing?

[@ealanosborne]

Yes, with the 2020 and newer models, there is “preamp” mode, which shuts off all internal amps, if you happen to power all your speakers externally. Otherwise - say if you’re using a 3-channel amp to power your front soundstage - any signal that doesn’t reach the internal amp (because it’s going out the pre out first) doesn’t activate its corresponding internal amp.

[@whbwin]

really helpful video！but I’m wondering why assign 9.1ch for the 5.1.2 setup?why not choose 7.1 since we only have 5ch on the floor and 2 on the top?

[@ealanosborne]

I believe you can do that as well. More than one way to skin a cat. 🐈

[@whbwin]

@@ealanosborne hahaha got it thanks

[@sooknandannishan]

Thanks mate, I been looking for a video like this for a while now. Planning to do either a 5.2.4 or 7.2.4 set up. I have a room that's 4mx4m that I am planning to set up my home theatre but still undecided which speaker config is best for this room size. Keen to hear your thoughts?

[@ealanosborne]

Since your room is a square, might as well do a cube - 5.2.4. Typically a 7.2.4 works best in a rectangle. 👍

[@rodgerkempisty4721]

Hello great info I have a Denon AVR X8500 HA How do I hook up a 3 channel amp and charge in the assign menu?

[@ealanosborne]

How many speakers do you have in your system?

[@ET-yr6st]

is their any scenario where any other connections on the back of the pre amp are highlighted or just the front speakers and/or height speakers in the software on my Denon AVR x3600h. Thank you this video helped a whole lot.

[@ealanosborne]

Just the front and rear heights need to be assigned if you’re using a combo of internal and external amps. Otherwise, all the other pre outs are “standing by” if you want to connect an external amp to those as well.

[@ET-yr6st]

@@ealanosborne Thank You

[@NTBS]

hi i enjoy your video very much, i have a kilpsch 5.1.4 dolby atmos built in speakers with klipsch r600 (2) towers & a denon avr-x1700h 7.2 reciever. what do you recomend for the settings sir?

[@highland-oldgit]

Right ho. Here's one for you. I'm going to use the zone 2 outputs to my Audiolab 6000A stereo amp (which can be run as a power amp) and this will drive the front speakers and subwoofer. Is there a configuration that allows me to run the Audessy sound setup with this ?

[@robcapel9825]

Thanks for the detailed video. I am trying to setup my brand new Denon AVR-X3700H with a 5.1.4 configuration. I have 3 speakers in the front (plus subwoofer). I have 4 in ceiling speakers and two surround back speakers. The setup will not allow me to specify only the surround back without the side surround speakers. Does anyone know how to get this configuration defined? I used the 9.1 assign mode. There is no space in my room for side surround speakers.

[@ealanosborne]

There’s no way to specify a 5.1.4 with surround backs. If you happen to have your surrounds behind you in a 5.1.4 configuration, they would still be considered surrounds since you don’t have 7 ear-level speakers. It’s just a matter of labeling and identifying speakers. But in the software, you would still just use 5 floor speakers in the amp assign section, and in speaker Config you would still have 2 surrounds, and “none” for surround backs, even though they are physically in the surround back position. Make sense? 😀

[@robcapel9825]

@@ealanosborne Thank you for the quick response. That makes perfect sense, and I was able to define all my speakers. I am moving from a 5.1 system with some new speakers and this new Denon receiver. I would have been lost without your help.

[@ealanosborne]

@@robcapel9825 Glad I could be of assistance! 😊👍