Most Common Reasons Your Check Engine Light Is On

[@talmania1]

Thanks a lot, removed my air filter cover on my Toyota Land cruiser, to check the rubber seal, and found my diesel sensor disconnected. Pushed it back in, closed the filter cover, and it solved 2 problems in one go: the engine light turned off, and my diesel gouge stopped giving false reading of low fuel. Again, many thanks, Big Like from Israel.

[@DespairRepair]

Hi, you're welcome and glad the video helped! Thanks for watching and all the best to you :-)

[@halamish1]

Excellent presentation. Spoken clearly without shouting!

[@DespairRepair]

Thank you very much for the kind words and thanks for watching!

[@solar365]

Excellent advice, just saved me £114 diagnostic test at Honda garage by cleaning around rubber seal on fuel cap🥳

[@DespairRepair]

You're welcome and glad if the video helped!

[@RickyPisano]

I have a 2005 Ford 500 Limited that's been meticulously maintained. My "Check Engine" light recently came on and the problem was the gas cap. Be advised the light WILL NOT go off immediately. It will take a couple of cold starts to reset. Thanks man!!

[@DespairRepair]

Your welcome and glad the video helped! You're right, in most cars that's the situation. Thanks for the contribution and all the best to you! :-)

[@rachelaimer6284]

Did it just come on and stay on or did it come on flashing? Mine just happened tonight but I also thought after watching this video it’s could be my gas cap as well, since the other day I started my car and I smelled kind of strong gas and could not figure out why but did go get gas a couple days or a day prior.

[@RickyPisano]

@@rachelaimer6284 If the check engine light is flashing it definitely isn't the gas cap. That means it's something that needs immediate attention and you should stop driving. It could be you have a misfire if you smell gas. Misfires are when the spark plug in one or more of your cylinders isn't sparking to ignite the fuel/air mixture. This could be caused by a bad plug(s), a bad coil pack(s), clogged fuel injector(s) a bad signal from your ECM. The best thing to do is have it scanned. That will show you the error code that caused the check engine light to come on. Just remember, that only shows you where to start looking. You might pull a P0171 Fuel Trims are Lean. There are a few reasons why this could be. An 02 sensor might trigger it. You DO NOT want to just replace that sensor because there are other reasons that cause a GOOD sensor to send an error code. So many people do this. Then they reset the check engine light after replacing the part only to have it come back on in two days. Remember, it's just a code to let you know what to look at and narrow down the problem so you know you've got it. Vacuum leaks, a bad or dirty MAF sensor, tons of things can be off to trip that light. But...if it's flashing it's warning you that the problem is not good to keep driving. You could do permanent damage to you engine. You can buy a cheap scanner for about $20. More advanced ones run more. But a simple code reader is fairly cheap. I bought one for $20 that gives me the code and live engine data via Bluetooth to my Android. I can look at long and short term fuel trims, (very important on diagnosing how your car is running), misfire codes, 02 sensor readings, Catalytic converter temps. Remember, your cars ECM will make adjustments to things like fuel/air mixture to keep a 14.7/1 air to fuel ratio in your engine. So even though your car is running great you might still have a problem. You just don't know it yet because the sensors haven't hit the max to trip a code and have the check engine light turn on. If you notice your gas mileage has gotten terrible, you smell gas in the exhaust, these are signs that the ECM is making adjustments because something is off. The car will still run great but there's a problem. A vacuum leak after your Mass Air Flow Sensor is allowing un-monitored air into your intake throwing off that 14.7/1 air ratio your engine and ECM want. The ECM doesn't KNOW there's a vacuum leak. It just knows that there is more air than fuel. So, the ECM will send MORE GAS to your cylinders making your fuel trims go crazy. If they hit a max you'll get a P0171 code. Fuel Injection System Too Lean Bank 1 (or 2 if you have a V-6 or V-8). Most likely a loose vacuum hose, Dirty MAF Sensor or even a Dirty Air Cleaner. I know there is a lot of info here and you might not understand most of it. But a sensor code doesn't necessarily mean that sensor is bad. In fact most of the time it doesn't. So my point was to just save you money buying parts you DON'T NEED. You can email me if you have any questions. I'm happy to help anyone save money from rip off auto parts stores that WILL TELL YOU to buy this or that. They are WRONG 90% of the time. I hope this helps you. Feel free to ask any questions you have any.

[@rachelaimer6284]

@@RickyPisano Hi thank you! I do have one more and your response was actually very helpful and anything I didn’t know I just googled to find out so no biggie. When I started it up this morning the light did not appear. Could it be possible that it came on as warning? It is winter and there was a snow storm and I don’t think my grandfather pulled my car in his driveway after letting it warm up, I believe he just started it up and went to park it and then it shut off on him and he floored my gas pretty ruff to get it from the end of his driveway. I will still check as I had no time to do it in the mist of already having so much to do to add on to this. I’m hoping it was just a warning to not do that again or if not something very minor that can be fixed.

[@RickyPisano]

@@rachelaimer6284 If it went off and it's running OK then you should be fine. Keep an eye on your gas mileage and if the engine runs smooth. Like it normally does. If something is off the light will come on again. It may have been a very temporary low oil pressure signal because of the cold. That would be my guess by what you described. I wouldn't worry about it if the light went off on it's own. Something like a loose gas cap that triggers it will usually turn back off after a couple of cold starts once it's tightened. No biggie. I think you'll be fine. The newer engines post 2005 or so don't need to be warmed up. They have thinner, usually synthetic oil like 5W20 and when cold the ECU automatically runs the engine rich (open loop) until it's warm and hits operating temp and the O2 sensors kick in (Closed Loop). Then the air/fuel mixture is automatically adjusted by those readings. The old carbonated V-8's, Slant/straight 6's and 4 cylinders had way thicker oil like 10W40 and it would get like molasses in very cold weather and had to be warmed up to pump through the engine effectively. The Choke on the old carburetors would be open to make the engine idle higher on those engines and you actually had a "gas pedal". On these newer ECM controlled engines you don't. The pedal you press is actually an "air pedal" that opens and closes the flap on the Throttle body to allow more or less AIR into the engine as the ECM is in full control of your fuel that enters the engine based on the amount of air entering it at different speeds and RPMs. The air coming in is measured by the Mass Air Flow Sensor or MAF positioned in front of the throttle body to maintain that 14.7/1 air to fuel ratio. I still let my 2005 V-6 warm up a bit though before I put it in gear and take off. I still think it's a good idea to do that when it's really cold out to make sure oil pressure is ok and no warning lights stay on. I think you'll be fine though as long as the light is off and the engine is running like it normally does. I hope this helps you.

[@troyundroy1]

Thank you so much - sensor light was all due to the fuel cap. In the past I have been quoted thousands to fix this same issue.

[@jaskosijaric4021]

did chek engine light go off emidietly after you change gas cap? and on which car?

[@troyundroy1]

@@jaskosijaric4021 Kodiaq & no it didn't go off immediately. After a few cold starts.

[@cheryltune1292]

You explain everything very well and correctly!

[@DespairRepair]

Thank you!

[@stephenboyd4934]

But you need too mention the mileage with these problems because that's a big issue when looking at the problems ?

[@logandw5971]

Light on today. Straight to youtube ! Thank you. Best video here on this issue

[@DespairRepair]

You're welcome and thanks for watching! 🙂

[@joanmiles8760]

Thank you so much for this. I was on my way to collect my Grandchildren from school, tried the petrol cap tip & the light went off! Thanks again, saved me the trouble & money of going to the mechanic. Sincerely & so grateful Joan

[@DespairRepair]

You're welcome and glad if the video helped! 🙂

[@Flying-Fox19]

Thank you for this video. What I don't like about a franchise shop like the one I went to diagnose my issue, they always recommend to change to new parts vs cleaning it first. That would not be a good place to go so now I realize those small independent shops would do a better job. Never have them replace the part until they've look at everything and do the cleaning up under the hood. I have an engine check light again after 2 years now. The first time my O2 sensor was changed but it did not help, the shop had no idea. Finally we checked out the air intake and that was cleaned. It did the trick as I looked up the obd2 code online to find other areas of concern.

[@DespairRepair]

You're welcome, thanks for watching and sharing information on the topic!

[@ToFightTheGoodFight]

You're absolutely agree. Don't go to franchise setup. I don't mind paying more than to be rip-off

[@CharmCityAdam]

Solved the issue in check 1. Probably saved me a few hundred "analysis" from a tech, so thank you!

[@DespairRepair]

You're welcome, thanks for watching, and glad if the video helped!

[@tmd1505]

Such nature behind! Birds are chirping and peaceful and lush greeny area! Just wOw!

[@DespairRepair]

Hi and thanks for watching! Yep, we live in the countryside, that's the reason. Interferes a bit with the video but I hope people don't mind :-) All the best to you!

[@jilluthman7073]

Amazing view 😍

[@davidmckenzie3398]

They can send a man to the moon, but they can't make a sensor that tells you what problem your car has? SAD! 😢

[@DespairRepair]

Hi David and thanks for watching! You're right the present system has a lot of flaws and is sometimes unreliable, even to the point that some good old thinking and old-school problem-solving does a better job. Perhaps someday a car will have some sort of its own self-diagnostic system which will give more precise information. All the best to you!

[@Turnbull62]

It’s not that they can’t make a sensor that tells you, they don’t want to. They want you to have to take it to an authorised dealer. ££

[@dr.mohamedaitnouh4501]

try FIXD

[@eddiebecerra8578]

They don’t have a censor that tell you what’s wrong because there’s no money on that if you know the problem then they won’t b able to charge u 500 dollars to tell you there’s something wrong and if u wanna know what it is it’s another 300 dollars and if u wanna fix it then it’s half the cars actuall price

[@garryibbetson9912]

but did they send a man to the moon think about it

[@jcagam3811]

Thank you sir for summarizing those usual CEL problems. I think those are true for most make and model of vehicles.

[@yusufkilicaslan6543]

I’m doing same way I block the engine light by my arm and I’m not look this way

[@bdrm2009]

No one is around, so I want to tell someone...I just burned my nose hairs while lighting a miniature bowl. It sucked. That is all. 😂

[@R4M_Apex_GT]

lmao what??? 😂

[@romeysiamese6662]

Be careful. Or roll a doobie instead.🙂

[@nico-vc3es]

love this

[@MukoroJr]

😂😂😂😂

[@MukoroJr]

Did u get a buzz though despite that

[@CaptainB76]

I just cleaned my petrol cap and top of the petrol tank with WD40 and the light went away. Thank you for your help! I do think that providing the car is running well this isn't something to be worried about too much. Although I am glad this has now gone!

[@DespairRepair]

You're welcome, thanks for watching, and glad that the video helped!

[@freedom14639]

Thank you. My EML was on because of loose petrol cap. I tightened it and EML went out. Thanks pal great video

[@DespairRepair]

You're welcome and glad the video helped!

[@normasand8415]

@@DespairRepair by

[@kevinc1851]

Number 1 gas cap typically P0455 or P0456 with message fuel canister / evap being a bad seal I totally agree. I have resolved several of these. Usually the fill neck has started to rust preventing a good seal. A few rubs on the rust with sand paper followed by a bit of grease (Vaseline in a pinch) on the corroded surface will resolve.

[@DespairRepair]

Hi, thanks for watching and for sharing, much appreciated 🙂

[@ginapereira8948]

My check engine light came on but I couldn't get an appointment in town. I went to get gas an discovered my cap wasn't tight? Thank you ❤️

[@DespairRepair]

@@ginapereira8948 you're welcome and thanks fpr watching!

[@be_reselient]

I have the light on my mazda 2006 tribute with 90K miles The mechanics said its the air to fuel ratio and are quoting $3,000 to fix a list of different problems lol

[@daveleejones3060]

Well you sir are my savour , i was a 100 miles from home in my campervan when the dreaded light came on, reading in the manual it said it was the catalytic converter and drive to the nearest garage at 40 miles an hour?? I contacted the vw transporter site and there advise me to put my boot down to clear it ??? Be confused i stubbled onto your video , wow couldnt believe it but I tighten my fuel cap problem solved light went straight out , thank you so much 👍👍👍👌

[@DespairRepair]

Glad if the video helped and thanks for watching!

[@rabbit73au]

You don’t have to replace or clean O2 Sensors all the time sometimes you can clean them by using high quality fuel and when you have a chance put your foot down and it cleans them out I did it on the last car I had I got over 100.000 Kay’s and the cod didn’t come back

[@DespairRepair]

Hi Roger, thanks for watching and the good comment!

[@keanonsean649]

Just tightened my gas cap and it went off!!!!!; Thank you Sir!

[@DespairRepair]

You're welcome and glad if the video helped!

[@mattpryor-c2v]

Bro your the best, bought a new gas cap for 6 bucks problem solved thank you have a great day love IceMan

[@DespairRepair]

You're welcome and thanks for watching!

[@MsEMILY11]

Thank you for this video my Fiat had an engine warning light and saying start/stop not available and my car wasn't getting much power and cut out on me, my mechanic has found it was a loose air hose to the engine, cross fingers the problem has been sorted

[@DespairRepair]

You're welcome and thanks for watching.

[@devanshujoshi8393]

Thanks a lot for your video bro on mu way to airport and this popped up you helped sending you love ❤️

[@DespairRepair]

You're welcome and thanks for watching!

[@blackericdenice]

Air getting into the tank will not change the air fuel mixture. The light come on because vapors are leaking out of the tank.

[@andebrhan2]

Very well explained and I fixed my vehicle as you said thank you God bless you 🙏.

[@DespairRepair]

You're welcome and thanks for watching, glad the video helped!

[@agneseneme7538]

Wow thanks very much for your explanations. I have to checked mine because the lights been on for a while

[@DespairRepair]

You're welcome and I hope you solve the problem!

[@akili9319]

Thank you so much!!!! My cap was very loose after I got gas. I was rushing and didn’t notice that I didn’t turn it closed all the way!!!🙏🏼🙏🏼🙏🏼

[@DespairRepair]

You're welcome and thanks for watching!

[@ridehead8771]

Had my light on so I called AA (UK breakdown cover) diagnosed it and it turns out it's the Transmission Control Unit, however the car drives absolutely fine and no loss of power, the light went off itself within an hour as well, the car is Mitsubishi Colt diesel semi automatic. The AA man said its just a minor fault and just leave it and keep driving the car as long as it drives fine and there's no loss of power. We only had bought the car so we're not going to be overly concerned at the minute and hoping the light doesn't come on again lol.

[@DespairRepair]

Hi and thanks for watching the video! I think that the AA man gave you some good advice. The check engine light is notorious for coming up for minor faults like weak electric connections, loose hose clamps or other while the codes show more serious problems. Anyway, drive the car until the check engine light comes up more often or more serious symptoms appear. Just pay some extra attention in the meantime. Otherwise, you could just end up spending money and replacing parts that maybe don't need to be replaced. This is all from experience, btw. All the best to you and hope the light doesn't come up again :-)

[@Kirawolf1971]

Same exact thing happened to me. My check Engine light came on. Scanned with scan tool. Pulled 2 codes. One was gas cap. The other was bad battery connection. I was just about to get it fixed and the light went off. Drives, idles fine. No power loss.

[@anjalisadanandam]

Thanks for this informative video. In my car the coolant warning symbol came on, I let it rest and drove to my nearest destination and the check engine light came on. Took it the garage and they poured water in the radiator and but the light is still on. What would be the next best course of action?

[@mariuszmoraw3571]

Disconnect car battery for few minutes and connect. Might be that computer need reset.

[@dingouloo1055]

Yes because the light does not turn off immediately

[@dingouloo1055]

@@mariuszmoraw3571 you can also just disconnect the negative terminal witch is easier.

[@thedrifterr]

Thanks mate it was my gas tank cap, easy fix cheers 👍

[@DespairRepair]

You're welcome and thanks for watching!

[@thomassiddle1199]

what was your car doing .to make u change gas cap?

[@bellikattyms]

Camera coverage is poor. But Sir your explanation is superb.

[@DespairRepair]

Hi, thanks for watching and sorry for the late reply. Thank you for the kind words :-) hopefully the footage will get better over time.

[@nihithvlogs]

Once I have changed the Gearbox, this engine check light getting ON in red color. It is only appears when I travel to 5 or 6km continuously. If I stop the engine and start again, the indicator getting OFF. What may be the issue? Please advice me

[@abcputra6985]

Congratulations nice explanation regarding engine alarm light. As my experience car sir.. Thanks you sir 😁🌏💕

[@adrakdavra]

Very informative it solved my problem in like 30 seconds thank you

[@DespairRepair]

You're welcome and glad if the video helped!

[@NancySanders-om4ic]

Thank you,sir,for providing this very important information.Sincerely,N.Sanders.

[@DespairRepair]

You're welcome and thank you very watching us!

[@dammo1932]

Fuel cap was my problem. Thanks for saving me lots of money 👍.

[@DespairRepair]

You're welcome and glad if the video helped!

[@UltraxHere]

When did the light go off ? Instant or after some driving

[@dammo1932]

@@UltraxHere straight away as far as I remember

[@firoznanji1771]

Very well explained, I have 2004 VW Polo, 1.4L petrol engine. OBD code shows MAF sensor. Replaced it, but Check Engine light keeps coming back on, with same code. Will try to check Gas Cap, and Air Intake box. Thank You

[@DespairRepair]

Hi Firoz and thanks for watching! Certainly, worth the try, hope that any of the tips help!

[@petersack5074]

....sever the wire, to that engine light......

[@graysonlee1]

Sounded silly but I cleaned the petrol cap with WD40 and it worked. Many thanks.

[@DespairRepair]

You're welcome and glad if the video helped!

[@rqn1998]

This is a great video! Ive gone through all these except change 2 of my 02 sensors and clean the catal converter after taking my 2007 wm statesman to a mechanic without a resolution. The odbc gives off the p01010 (code that refers to the maf sensor..) unfortunately replacing with a new bosch one still didn't resolve it.. I may have that odbc code wrong above but it was for the maf... if the mechanic who is over 30 years qualified can't resolve im not sure what else I can try :(

[@tonygaytan9848]

Thank you for your knowledge. I was able to repair my vehicle.

[@victorapaliso9439]

The best things to do is use OBD scanner to be specific. The OBD reading give you accurate guide.

[@gigantor62]

My light's been on for 3 years....no problems.

[@semmrd]

Thnx for the tips. I believe i had a problem with the tankcap. Thanks again.

[@DespairRepair]

You're welcome and thanks for watching!

[@strikeeaglemodels1588]

I’ve got the warning light come up on my car.On inspection I’ve got oil on the spark plugs and coil packs on two out of the four cylinders.Sounds like the value gasket needs replacing.Would these cause the light to come on ?

[@PicmipPixel]

So my new Hyundai i20 started showing that light on, garage schedules but engine power is clearly limited... and it sounds like a paper on the wind sometimes, weird stuff... wonder if you could give some light on a possible issue.

[@DespairRepair]

Hi and thanks for watching! To be honest, it's hard to say with this information but it probably loses power since it goes into limp mode when the check engine light goes on. Regarding the sound, I would first check if everything on the air intake is OK and properly set and tightened. Especially do this if there was recent maintenance done. Hyundai is a good and well-built car and I doubt that something serious is wrong. Hope this helps.

[@livdouglas3410]

I have paid $918.10 at one shop, engine light back on next day, took another shop, paid $141.00, engine light back on, called mobile mechanic paid $100, check engine light back on, took to another shop paid $749.04, check engine light back on, they Firestone said bring back Tuesday morning see what else they need to do... they said need to reset the memory so that can pass inspection.... SMH ... 2008 DTS

[@DespairRepair]

Hi and thanks for watching the video! My goodness, that's a truckload of money :-(. The check engine light is known to be a money pit problem. One of the points of the video was to try and give a hint to avoid such expenses. Lots of times the error code is induced by other systems and parts that the error code doesn't show. Hence the constant unneeded replacament of parts: an expensive system of elimination that comes from the owner's pocket. This writing won't help a bit to solve your problem but at least ask the next people that come to exactly pinpoint the problem and stand behind their words. Best of luck with the repair.

[@tankisomakara8268]

Now i can see what exactly a problem on my car,thanks for a video and a clear message about why my engine light come on

[@DespairRepair]

You're welcome and glad if the video helped

[@domingapal8514]

The check engine light only came ON after I had changed the battery. How do you reset this? Should I remove the ground cable of the battery for 1min and reconnect to see if it goes away? Please advice. Thanks

[@DespairRepair]

Hi Dominga and thanks for watching! Yes, you can try to do that. When you take off the battery terminal, also press the horn to discharge the system totally. Keep the door or window open just in case, so you have access to the passenger cabin. If this doesn't work, then using an OBD tool is the next best thing. Hope this helps. Don't know why it showed up after the battery replacement, it shouldn't be that way. .

[@sptsean1838]

Thank you so much Sir. Your one of the best 😘

[@songsong8701]

Thank you so much🤝Just now I retightened the gas tank lid and the light went OFF!!!

[@DespairRepair]

You're welcome!

[@benjaminawuah271]

Just did same and the light went off…thanks

[@andrewmtwalo3836]

Thank you sir,just cleaned my gas tank cap with a clean dry cloth and immediately it went off 😊😊

[@DespairRepair]

You're welcome, thanks for watching, and glad if the video helped.

[@lsambrexi6173]

Thanks man you are genius..you solved my problem 🌺

[@DespairRepair]

Glad to hear that we could help :-). Thanks for the visit and nice comment

[@johnkamaru2037]

What's the main effect

[@Team-wr3ii]

Very good video. If the flexi pipe's broken can cause the EML problem?

[@DespairRepair]

Hi, thanks for watching and for the kind words 🙂 If you're talking about the pipe for the air intake, yes it can.

[@AtticTapes14]

Scotty Kilmer said ignore it till it gets worse unless light is blinking/flashing

[@DespairRepair]

Hi and thanks for watching the video! If Scotty says so, then it's the truth :-). Big fan of his. In fact, I think he's totally right. Trying to solve a check engine problem without a real symptom can end up in spending lots of money and time on repairs only to achieve nothing. Best regards to you!

[@obaidurrehman1102]

Thanks for your guidance. I resolved my ‘Engine Check Light” problem by removing earth terminal of battery for one minute, pressing horn and then re-fixing the battery terminal. Check light gone. Thanks again

[@DespairRepair]

You're welcome, glad the video helped, and thanks for watching!

[@pimpernelsmith3798]

Excellent the reset worked. Engine light now off. Liked!

[@DespairRepair]

Thank you and glad if the video helped 🙂

[@fithawiyemane6558]

I saw the video And l check my car l slove just the cup of gas not closed properly thank you so much l appreciate you for sharing ur video

[@reneebernal1895]

What are some causes of it cutting out? Mine keeps acting like a shift problem , cuts out like it wants to die out.

[@DirtySony]

same idk what the problem is let me know if you found out?

[@Pak1947KHI]

What is a tool with Exclamation mark light means on Toyota Aqua? Thank you

[@TheNobbynoonar]

Thank you for a clear and concise video.

[@DespairRepair]

You're welcome, thanks for the kind words and for watching!

[@gratitudetouniverse3754]

What do you call that equipment that checks the lights on the dashboard of your car so yo will know in details ? Thanks

[@DespairRepair]

Hi, and thanks for watching! If we're thinking about the same thing, it's the Onboard Diagnostic reader, aka OBD reader

[@kolourmeretro6197]

Should I still drive my car I’m scared and poor at the moment 😭

[@leonardsmith3833]

Nothing with happen , but get on top of that business 👌

[@beybladeplushandbedwars957]

🤣🤣🤣Mannnnn me and you both man… and not exactly in that order 😩😩🤣🤣

[@georgewbushcenterforintell147]

Me 2 .🎭

[@andreassitompul1134]

You can still drive it. Ive been driving mine for over 1 year

[@lethagramlich417]

Me too.

[@RomeoMoDernoo]

Is the Toyota Yaris 2011 Terra Sporty engine belted or chained?

[@frauditorschmoditor]

What about a bad power steering pump, can that cause the light?

[@DespairRepair]

Hi, and thanks for watching! It depends on the car model but sometimes yes, it can. However, like on the Skoda for instance, there is a separate warning light for that.

[@bjork0]

Hello, I got a Toyota D-Cat and the engine light is on, but also the vsc and trac light. When this happens, the car loses ALOT of power and can after a while reach 80 km/h. We have scanned the car and got one code, P0400. We have checked almost everything, air filter, MAF sensor, 02 sensor, swapped EGR but with no success. Have any tips on what to do before we send it in to a mechanic? Thank you for a great video anyways!

[@DespairRepair]

Hi Tim thanks for the kind words and for watching! You've checked more or less everything. I would check once more for an air leak (like punctured hoses, loose clamps, or else). Sorry for the late reply and hope this helps.

[@michaeltegegne2698]

That was very helpful, thanks.

[@DespairRepair]

You're welcome and glad if the video helped!

[@dagorilla5177]

Very helpful! Thank you 🙏🏾

[@DespairRepair]

You're welcome and thanks for watching!

[@valeriemcglen9138]

My engine light came on, my radiator needle went straight up to the top and we heard a rattling noise. The water and oil was fine. I've just checked my petrol cap and that is all good. My husband put coolant in the radiator (not much) The next day, the engine light was off and the radiator needle was normal. Do you know what my problem could be?

[@DespairRepair]

Hi and thanks for watching! There could be a couple of reasons, if the rattling sound is still present when the engine is running check when the water pump was last replaced. Also, check the coolant fan radiator. Hope this helps.

[@dhutsering]

Very helpful tips > gas tank cap was wrong. Thank you so much. Otherwise mechanic will charge unnecessary $$$. God bless you !

[@DespairRepair]

You're welcome and glad that we could help 🙂. Thanks for watching.

[@tomjones1396]

My check engine light keeps coming on because what the service desk manager at Pep boys told me it's because of condensation/moisture building up in the system. Could you please explain this and what is the solution to prevent or resolve this issue with condensation build up in order to prevent the check engine light keep coming on? I have a 2013 Chevy Equinox SUV

[@banjammy7367]

Good information ,will the heat sensor turn it on?

[@DespairRepair]

Hi and thanks for watching! If you're talking about the temperature sensor, yes it will, it's a common fault on VW group cars of that era. We're making a video soon just about that.

[@BH47658]

Thanks Sir, your very first solution worked for my Chevy Aveo.

[@DespairRepair]

Your welcome and thanks for watching!

[@normasand8415]

My Nissan won't start I have a code reader hook to it but I don't know what the code means it's 150 9141

[@dangerousdanny8290]

Have had my pickup since it was a pup. Same mechanic has done the maint, on schedule, since then. Before heading home from the beach, 2 hr. trip, I stopped for gas. Noticed the idiot light just as I hit the driveway. I'll be darned!! Thank you for this vid. Was the 1st thing on your list...didn't have the gas cap on tight. WTF?? Like I'd never fueled up before.

[@DespairRepair]

Hello and thanks for watching! Glad the video helped. I've had a similar case, the only difference was the gas pump wasn't a self- serving one. The worker that poured gas forgot to put back the cap altogether and left it on the roof. Luckily I noticed in the rearview mirror that something fell off beside the car. Since then I always check if the gas tank cap is tightened and is returned properly. You can never be too careful :-)

[@robbieguerrero3351]

Master Mechanic, Thank You!

[@vinoth091]

Really thanks it works I do have Skoda rapid , follow the protocol fuel tank was not closed properly hence solved thanks cheers 🎉

[@DespairRepair]

Hi and thanks for watching. Glad that the video helped and that you solved the problem. By the way, nice car you have there.🙂

[@phuketbungalowinfo2757]

nice video, thx for sharing, having the prob on my CB500X and will follow the steps you mentioned. :)

[@DespairRepair]

Hi and sorry for the late reply. Thank you for the kind words and for watching, hope the video helps solve the problem 🙂

[@phuketbungalowinfo2757]

@@DespairRepair thx for reply ::)

[@thomassiddle1199]

have to change all 12 plugs in my Bentley continental gt my question is do I need any other parts to take with me other then the 12 plugs?

[@marceloperalta4908]

Great video... could you show us how to reset the light?

[@Q-00]

Disconnect the negative connection from the battery for a minute.

[@issaseck1258]

Thank you so much I owe you that one but how to make the Light disappear after fixing it

[@DespairRepair]

You're welcome, glad the video helped, and thanks for watching!

[@thembambhamali9253]

Hi there I have a massive problem my Toyota 4zz manual. It's keeps having a very slow delay with clutching and slow in taking off. Infact is it has power loss when driving uphill and engine light is forever on.

[@DespairRepair]

Hi and thanks for watching! That's a pretty broad explanation. Try using an OBD tool and see if you get an error code.

[@irfanbinsaleem]

Thank you very much bro, putting the fuel cap properly solved the problem and really worked. Very big thank you and God Bless you.❤

[@DespairRepair]

You're welcome and thanks for watching!

[@Alex-fi9cb]

Thank you.thank you and very very thank you for sharing video clip. Its very helpful.thank you.

[@DespairRepair]

You're welcome and thanks for watching!

[@nickmurray1530]

Great video explaining thank you

[@salumv1726]

Hi my car have same issue 2012 VW jetta.. battery already dead i hope this is the issue. However I check with OBD showing plug 3 misfire and engine pressure is low. What should I do Could you help me....

[@levipadre]

Hi, thanks for the video. I have a question, but maybe it's a stupid one. When I put the key in and I can see that all warning lights appear, then disappear one-by-one, except one (light engine), but that also disappears when I start the engine, is that a problem or not?

[@mrkalenda4911]

That doesn’t mean anything. Mine does that too

[@levipadre]

@@mrkalenda4911 Thank you!

[@Деловкепке]

How does the fuel tank cap relate to engine light management?

[@DespairRepair]

Hi and thanks for watching! Air gets into the fuel intake and causes a disturbance in the air-fuel mixture triggering the check engine light.

[@emanuel9537]

Is this for every car?

[@DespairRepair]

Yes, it is meant as a general explanation

[@enkay110]

In what sequence should you check the possible faults? Clearly, the most expensive (replacing catalyst) should be the last.

[@DespairRepair]

Hi and thanks for watching! Yes, that's the right way, start from the gas tank cap and go from there.

[@rowellroque1421]

This save m lot of money.. Tnx man

[@DespairRepair]

You're welcome, glad that the video helped, and thanks for watching!

[@truthseeker9487]

Can I hole on the windshield washer reservoir cause this ?

[@haiderzaman1888]

Hello you Are very good teacher.thank;s.

[@zainmehmood4230]

I have P104 error code. I did clean the MAF sensor with the special liquid for maf but problem is still there. Few months back I had check engine light and I replaced the lambdasond after catalaytor and it helped. Will check the fuel tank cap now. Should I need to replace the sensor again?

[@DespairRepair]

Hi, well if I understood right, you just cleaned the sensor and didn't replace it. Cleaning, at least from my own experience has success to some point. The usual outcome is to replace the part if you want the repair to last. The code is for a faulty MAF sensor but there could be other problems triggering that code. I would recommend starting with cheaper and more simple things and then replacing more expensive parts. Check for air leaks also. Btw, what car is it and with what engine?

[@bellebb256]

Thank you,after put in gas the check engine light turn on,i clean the cap now,the light is off. Thanks.

[@DespairRepair]

You're welcome and thanks for watching!

[@paradiseparadise-wr1wc]

Big love and respect to you

[@DespairRepair]

Thank you very much! :-)

[@ugoeju5998]

good day sir, is it possible to convert my used 2008 kia gran carnival diesel engine to petrol engine. thanks for your quick reply

[@DespairRepair]

Hi and thanks for watching! Don't know what you mean by converting. If you mean swapping the engine I guess it is possible but it's a complicated job that may not be cost-effective.

[@ugoeju5998]

@@DespairRepair Thanks sir for your quick reply. Ok I will provide more details regarding my earlier quotations

[@ilirfazliu7817]

Thank you for the video. Is this a serious problem? My VW Golf 2011 is showing the same yellowish light, it stays on all the time when I’m driving. How many more km can I drive like this?

[@DespairRepair]

Hi and thanks for watching! To be honest, if there's no immediate sign of danger, you can drive for hundreds of kilometers (this is from personal experience). But nevertheless, hook up an OBD tool as soon as you can and get the error code. It's sometimes just a glitch in the system and sometimes it's more serious. Hope this helps.

[@ilirfazliu7817]

@@DespairRepair hi and thanks for the reply. I sent the car to my mechanic, since I have a long journey planned and I didn’t want to take any risks, and fortunately the issue was minor, just a problem with the glow plug. He said that I shouldn’t have to worry about that, and I could change them later also, but before winter. Thank you again, and all the best.

[@Scythe_Voltage]

Until it breaks

[@Fernando-nj1pg]

Hi i have a question.. i have the BMW M3 COMPETITION and when i just start ignition not the motor all the warning lights illuminate and disappear except for the engine light. But when i start the motor press 2x the ignition button its all off no warnings car status ok etc. Is this normal at bmws?

[@DespairRepair]

Hi and thanks for watching! First of all, congrats on the car, very nice piece of machinery. Regarding the check engine light, best connect an OBD tool and see if there are any errors, just in case. It might be just an electronic glitch of some sort but check it out.

[@bobbeauchamp4082]

any chance you would know why i have a misfire #1 cylinder@ 1000 rpms or less ,no other codes ,,check engine light on

[@lindeelou6946]

Just putting it out there.... My Management light came on. I felt sick to say the least. Had it reset and it came on AGAIN the next day. Turned out to be my petrol filter. Phew ! Car is running like a dream and no light. Its been 2 weeks 😊

[@DespairRepair]

Hi and thanks for watching! Thanks for sharing and glad you solved the problem 🙂

[@DespairRepair]

Just watched the Tigra video of yours, congrats on the fix, it's very valuable information for someone with the same problem.

[@lindeelou6946]

@@DespairRepair Thanks. A girls gotta do what a girls gotta do 🤣

[@R.KHAN86]

Hi just got my Honda civic 2018(auto) serviced and engine management light came on 😢 any idea what that could be? Thanks

[@DespairRepair]

Hi, and thanks for watching! The best way to find out is to connect an OBD tool and get an error code. You can also check for basic problems like the gas tank cap or minor air leaks. Those are very well-built cars, so hopefully it shouldn't be a big problem 🙂

[@R.KHAN86]

@@DespairRepair I am going to take it to the Honda dealership tomorrow, as they serviced it today

[@DespairRepair]

@@R.KHAN86 in that case that's maybe the best solution. It's probably a minor fault