The easiest and most available method of diagnosing a pre 2000 mercedes and it is free too, for me it was the only way to clear fault codes on my convertible top module. Please download the fault code PDF, which is in the description. Thank you for watching and subscribing.
@brandonfowler60139 ай бұрын
I am making the code reader. What is the clear plastic junction piece called and where can I find one?
@BenzAddiction9 ай бұрын
@brandonfowler6013 TBH I am not sure, just use what is available, that's just decorative:)
@TheBackpackStrap6 ай бұрын
@@brandonfowler6013 thats a domino connector.
@wireless80211x15 күн бұрын
Hello World Blink. A1 in three weeks of research and sharing. Thank you ! Went down the rabbit whole with Jaguar electronics..Now it's Mercedes turn. Read 1 pair behind the audio head unit so I got my Krone punch down tool out. Now we talking connecting a light globe for the vehicle to make it purr and Ohm. The path of least resistance, keep it simple, bring back analogue 🙂 Oils are not just oils.
@BenzAddiction15 күн бұрын
You are welcome 😊
@Mrphantom198815 күн бұрын
Thank you! I copied your blink system. It lights on when I hold it for 3 seconds, but I am getting no blink after that at all. That goes for all pins, same thing
@BenzAddiction15 күн бұрын
That's weird 😕
@Mrphantom198814 күн бұрын
@@BenzAddiction Rick's pdf file for error code says, no blink or 1 blink is no error but Mercedes USA pdf file doesn't say anything about no blink. Any thoughts?
@MohammedAldawsari7 Жыл бұрын
can I simply run 2 wires from 12V DC LED light and from the negative wire a switch wire? no fancy block as yours😂. I've seen even more sophisticated self made OBD readers. I don't want to over do it. is the block important? thank you very much for all your helpful videos!
@BenzAddiction Жыл бұрын
Hello, there is no fancy thing as long as you keep your wires safe and insulated. Just follow the diagram and good luck 👍
@seshachary5580 Жыл бұрын
great service. very educative .Thank you regards
@BenzAddiction Жыл бұрын
Thanks mate
@raymondr77693 ай бұрын
Thank you for posting this video! I’m in the same boat with my 96 SL320. The foxwell and C3 could not communicate with my 38-pin connector. Going to try this today and see if it works.
@BenzAddiction3 ай бұрын
👍 👌
@MarioPrivitera-x1g5 ай бұрын
HI. Is it possible to reset the SRS light on a 1997 Mercedes W210TD. Thanks
@BenzAddiction5 ай бұрын
I think it is possible with this method.
@RuudyL4 ай бұрын
The best thing to do is not buy a Mercedes, otherwise you are just looking for trouble
@BenzAddiction4 ай бұрын
Yeah, we love these dramas :)
@chrisforrest7034 Жыл бұрын
Actually 96 was the year ODB2 was introduced.....
@BenzAddiction Жыл бұрын
In some countries...
@robertpsotka35257 ай бұрын
1996 USA Mexico and Canada
@caiopereira977 ай бұрын
Boa noite. Para apagar avaria do Air bag luz srs, consigo fazer dessa forma ? Retirei o volante com a chave ligada
@JeremyGustaSalsa Жыл бұрын
Thank you very much for the video and the link. I hope it help me to find a combustion failure...
@BenzAddiction Жыл бұрын
Thanks mate, fingers crossed 🤞
@salehalsabahi34845 ай бұрын
I like your video and your explain but for example if i need to check the electronic transmission 722.6 ? If there is fuolt ! How many times will light?? Please answer.. great service. very educative .Thank you regards
@BenzAddiction5 ай бұрын
Thanks bro, It depends on the fault, you need to count the numbers then based on the number find the fault.
@kendallmullenix569410 күн бұрын
Any update on this? Trying to figure out how to reset codes for my TCM. I replaced the conductor plate twice now but I’m not convinced the code has been cleared properly using the OBD2 port. I’ve read I have to use the 38pin port to clear it properly.
@brandonfowler60139 ай бұрын
First of all, thank you for this video! I made a code reader to diagnose my ASR light and limp mode for my 92 500sl 16 pin connector. I'm in the US by the way. I tested the "Electronic Accelerator / Cruise Control / Idle Speed Control (EA/CC/ISC) w/ASR". The book says it's "Closed throttle recognition signal to engine control module (HFM-SFI or Left LH-SFI) Fuel safety shut-off to engine control module (HFM-SFI or left or right LH-SFI)". Can you point me in the right direction? Thank you again!
@brandonfowler60139 ай бұрын
Update, I reset the code and then went for about a 5 mile drive. The ASR light came back on but not limp mode.
@BenzAddiction9 ай бұрын
I would do a google on this...
@BenzAddiction9 ай бұрын
Better than the limp mode 😉
@petter72523 ай бұрын
So I made the testing circuit, but when I press the button, nothing happens. If i reverse the circuit but not connect 16 , i have led light. So I have 12 Volts on all test points but when I push it to ground with the button, nothing happens afterwards.. Why is this?
@petter72523 ай бұрын
I checked my wiring again, diode was wrong way around, but I still have trouble getting it to blink on error codes, the led lights when I press the button now. But no blinks after i have pressed it for 3-4 sec.
@BenzAddiction3 ай бұрын
Just check your circuit logically again an refer to the diagram shown in the video, soon I am going to use the same test light on a W124, good luck.
@JulianoBarbosa-b1v2 ай бұрын
@@petter7252 Hi Petter7252. Could you solve this issue? I have same situation, no flashing after 3 or 4 seconds.
@petter72522 ай бұрын
@@JulianoBarbosa-b1v no i didnt solve it, i dont know if it matters but the car had been standing without power for at while. But im guessing i should atleast have gotten the one blink "ok/no faults" led. But I never did...
@JulianoBarbosa-b1v2 ай бұрын
@@petter7252 Hi Petter, yeah, same here, my car is a R129 1999 but still has 38-pin connector, I was wondering if it has a different diagnostic system. Thanks for your attention, if I find something I will keep you posted, maybe @BenzAddiction can help us meanwhile.
@George-f8m6 ай бұрын
Thanks for your videos, always very informative and because you're based in Australia is even better. I have just bought a '96 Sl500 r129. As this video was done about 9 mths ago have you searched anymore for an OBD scanner that will diagnose the r129 fully including Roof and Suspension ? Thanks George
@BenzAddiction6 ай бұрын
Thanks mate, the situation for 96 year might be better and you might be able to diagnose using a OBD2 Scanner. I am not 100% sure though on the brand you should use.
@bernardwarr41872 ай бұрын
I can’t pull the codes on this W202. I have a LED tool, it works on my w124 but can’t get it to flash any codes back
@BenzAddiction2 ай бұрын
Even form socket number 8?
@bernardwarr41872 ай бұрын
@@BenzAddiction I can see which pins have connections. I tried them all. I get the LED on with the button, but no flashing? Many thanks for any advice
@JulianoBarbosa-b1v2 ай бұрын
@@bernardwarr4187 Hi Bernardwarr4187. Could you solve this issue? I have same situation, no flashing after 3 or 4 seconds.
@bernardwarr41872 ай бұрын
@@JulianoBarbosa-b1v works perfect on my 500E W124, but only gets the light on, no flashing at all on the W202?
@JulianoBarbosa-b1v2 ай бұрын
@@bernardwarr4187 Hi Bernard, mine is a R129 1999 and only gets light on, no flashing, If same tool works fine on your W124 I guess system is different after 1998.
@st.dardust_garage Жыл бұрын
would this work on a 2001 CLK w208? I'm european so my car does not have OBDII onyl the 38 pin
@BenzAddiction Жыл бұрын
Should work
@st.dardust_garage Жыл бұрын
@@BenzAddiction Thanks!!! I'll let you know so you can add the info to the description ;-)
@st.dardust_garage Жыл бұрын
@@BenzAddiction Where did u buy that plastic thing that holds the wires and how is it called? (sorry i'm neither english neither expert on circuits)
@BenzAddiction Жыл бұрын
@@st.dardust_garage I think that is called a wire terminal. But you do not need to have that simply use duct tape to secure cables.
@st.dardust_garage Жыл бұрын
Thank you very much
@petartodorov2714 Жыл бұрын
Thank you
@BenzAddiction Жыл бұрын
You are welcome
@danludwig36794 ай бұрын
You have to check each pin individually? How do you decipher what the code means?
@BenzAddiction4 ай бұрын
All this data for codes are available online if you google it. Positive and negative is always fixed, the data cable (green) is for different modules.
@danludwig36794 ай бұрын
Thank you. If I’m having starting issues, what pins would you recommend checking? The car was running great and then it stalled and won’t start. Just replaced fuel pump. No change.
@BenzAddiction4 ай бұрын
@@danludwig3679 These modules are not very sophisticated, I would start 1. Checking fuel pressure 2. Pull a plug wire and check for ignition while cranking. If it is fuel related, fuse and pump relay to be checked. Ignition related: might be coil...
@danludwig36794 ай бұрын
@@BenzAddiction thanks again man 👍🏼. Fuel pressure is good. I will check for spark.
@oliverlindhorst6436 Жыл бұрын
thank you for the video. I've a china-sd too. Same Problem for example with W210. With the advice of your video I can help myself a little bit more. ☝