2010-2016 Hyundai Genesis Coupe Interior LED Installation | Diode Dynamics

[@AnyBodyWannaPeanut]

Thanks for these informative videos! You guys rock!

[@Jecsennnahhh]

I just did the interior installation. All stage 2, no circuit boards. Like some of you, I ran into the same issue. I blew a fuse two fuses. At first I thought I accidentally touched the copper with my screwdriver. But on the second try when I tried to input the bulb into the housing, the tip of the LED also blew the fuse. All this was from the vanity light. My personal advice is to either disconnect the battery or disconnect the fuse. I went with the second option as it was much easier. If you have no idea what you're doing, you'll still be able to do it. The fuse box is on the driver side. Pop the little door open and on the top right of the fuse box is a 10amp LP fuse (see owners manual and you'll figure it out.) Your car also has a few spares you can use in the engine fuse box area or you can buy a pack of 4 for like 3 bucks at Pep boys. Use a plier and just pull the fuse out and replace it. Good luck. :-)

[@johncasey3415]

Jecsennnahhh Hey I am trying to install the stage 1 led's in my 2013 3.8 Track. I got them all installed and working and then I tried those damn vanity lights. I blew a fuse (I think the 10A LP) one, which rendered my map lights, glove box, and trunk lid lights no longer working. I replaced the fuse, and those three lights started working again. However, the vanity lights still don't work. Do I have them in backwards maybe? I kinda ran out of daylight today so I will try flipping them tomorrow. Also, where is the engine fuse box area? lol

[@Jecsennnahhh]

John Casey Hope I'm not too late or hope you got everything fixed, but if you need spare fuses it's in the engine bay. For you it's on the lower right hand side in the box area. You should find a few spares. Anyway, try to flip them. My suggestion is to unplug the battery first or remove the fuse. Let me know how it goes! Good luck!

[@MrBillagordon]

Great video! Just ordered bulbs. Thanks!!!

[@Hokagebam]

Great video! Buying as we speak now.

[@diodedynamics]

Thanks! Don't forget to use the code "JULY4" during our Fourth of July promotion to get 20% off ANYTHING we have!

[@Hokagebam]

@@diodedynamics thank you for the code! I purchase my kit. Do you guys have hid or whatever it's up to date for the headlights? 2011 genesis coupe. I looked thru the site and I think high beams? But I wasn't sure.

[@diodedynamics]

@@Hokagebam No problem! We offer HID conversion kits for the High Beam and Low Beam on a 2011 Genesis Coupe. If you have any other questions, just give us a call at 314-205-3033, Monday-Friday 9 a.m.- 5 p.m. CST, or shoot us an email at [e-mail]!

[@youliankateliev747]

Thank you for the video, If i am just replacing the license plate lights for the back license plate... Do i have to unplug the battery still? Can i just do it with the car off and then test the lights. I noticed in the video that the light went on as soon as you plugged it in the license plate spot,? I assume the battery was on for this ?

[@bradameir]

any video or description maybe even instructions for a 2012 genesis sedan replacing the floor bulbs and ground lighting on the bottom of the doors?

[@diodedynamics]

+brady tyo Next time we have a Genesis Coupe into our garage we will be sure to shoot more videos. In the meantime, if you would like any assistance, please don't hesitate to contact us!

[@liban747]

Which fuse for glove box light its not turning on with parking lights on

[@diodedynamics]

Please go ahead and give us a call at 314-205-3033, Monday-Friday 10 a.m.- 5 p.m. CST, or shoot us an email at [e-mail], and our in-house US service team would be happy to help you with that. Hours: Monday-Friday 10 a.m. - 5 p.m. CST Email: [e-mail] Phone: [phone]

[@fxdl20]

do I need to unplug battery to install all of these?

[@diodedynamics]

+Justin Satterfield No, you do not. Feel free to contact us if you have any further questions!

[@Raul69]

I guess unplugging battery should work and not blow fuses

[@diodedynamics]

Raul, we always suggest unplugging the battery while installing our products. This will prevent blown fuses. When you don’t unhook your battery, it can cause instant voltage spikes or improper grounding, which will cause issues.

[@zacharysoun5612]

Sir. You touched the diode with your bare falanges

[@diodedynamics]

Hey Zach, this won't effect these LED bulbs like it can with a halogen or HID.

[@ireandelumen9899]

All bulbs are the same size ?

[@diodedynamics]

No, they are not all the same size. Here are all the different sizes you will need! www.diodedynamics.com/interior-led-conversion-kit-for-2010-2016-hyundai-genesis-coupe.html

[@kanor8233]

Hi, Is this will be the same Steps for a Hyudai 2009 Elantra ?

[@diodedynamics]

kano R , installation for your Elantra is going to be very much the same! If you have any questions or run into any issues don't hesitate to shoot us an email at [e-mail] and we would be happy to help you out. Thanks for your interest!

[@terrencehill7309]

is this the same if I put LED lights in my 2005 Hundie Tiburon

[@diodedynamics]

+Terrence Hill, yes, it is! Below is an installation video on how to install our interior LED bulbs in your Tiburon. If you have any other questions, feel free to contact us! kzbin.info/www/bejne/fV68eHV_aNGtrpI

[@chive_1585]

fyi don’t use the screw to remove vanity light 😭😭😭😭😭

[@diodedynamics]

Sorry about that! A trim tool could also work well for vanity lights!

[@ogwarsaw1]

Stage 1 and 2 bulbs for the trunk light blows my fuse. Will the board light be any different?

[@diodedynamics]

If you are using a screwdriver or another tool to take the bulbs out, that might be causing the the circuit to short and blow a fuse. If you are still having troubles please shoot us an email at [e-mail]. Thanks!

[@ogwarsaw1]

Diode Dynamics What tool should i use then? something thats non metal? doesn't the guy in the video use a screw driver?

[@diodedynamics]

msjconnolly Try not using the screwdriver when adjusting/removing the bulbs. In this particular video, using a screwdriver was not an issue, but it often varies from vehicle to vehicle.

[@Jecsennnahhh]

Diode Dynamics I didn't use a screwdriver, but the tip of the bulb blew a fuse regardless.

[@girlsrockurboyz]

I cannot get the vanity lights out of headliner.

[@diodedynamics]

+girlsrockurboyz Those small bulbs can be tricky to remove! Have you tried threading a piece of Scotch tape behind the bulbs to pull them out from the middle?

[@girlsrockurboyz]

The entire housing will not come loose from the headliner. I've put all my might I have on it. The headliner wants to come with it and I don't want to tear up my new car.

[@diodedynamics]

girlsrockurboyz Please give us a call at 314-205-3033 Monday-Friday 9 a.m. - 5 p.m. CST, and we will help you troubleshoot and make sure you are using the right tools.

[@permmebro]

hi, did you end up getting this resolved? I'm having the same issue in my 2013 gt

[@diodedynamics]

+Austin Dale Contact us at contact@diodedynamics com and we can make sure you're using the right tools!

[@koreyphillips5392]

how do you get the map light bulbs out on a 2005 hyundai elantra?

[@koreyphillips5392]

@diodedynamics

[@diodedynamics]

+korey Phillips Please send us an email at [e-mail], and we can give you some tips!

[@KatherineGrace1]

My lights don't look like this. 2012 hyundai genesis

[@Darth_Arashi]

Trunk light LEDs don't work for me

[@diodedynamics]

+Adrien Robinson We are sorry to hear about the issues you are experiencing with your bulbs! Please give us a call at 314-205-3033 Monday-Friday 9 a.m.- 5 p.m. CST, or email us at [e-mail], and we can help you troubleshoot and send replacements if necessary.

[@slopez101711]

I blown the fuse trying to do this what walt fuse should I replace the stock for?

[@DoctorGaga87]

10amp low profile fuse. I did the same thing

[@woofwoof9819]

Guapo I know I’m late but which slot do I put it in I just blew mine