Complete disassembly of a Shimano Citica 200HG by Papa Chops' Rod And Reel Repair. Headquartered in Austin, Texas. Visit us at www.papachopsat... or call us at 512.294.3155. A Full Boca Bearing Upgrade is confirmed and available.
Пікірлер: 22
@John_D28 жыл бұрын
for ppl watching , the bearing on the bottom of that main shaft always needs lubed and so does the super free bearing (for the pinion).
@outdoorssmith54543 жыл бұрын
I took a shimano slx dc apart as my first reel ever to take apart and I got it all back together fine it was rough and the dc didn’t work again after that lol, I took it apart because I got sand in it and I had to clean it out
@znal153 жыл бұрын
Fajny film. Dzięki
@TeamWagy7 жыл бұрын
I'm 17 and completely stripped a citica 200e down to the frame for extensive cleaning by severe neglect and abuse by the previous owner and rebuilt it. If I can do it, you can do it!
@MrVicg19908 жыл бұрын
Do a boca bearing upgrade for the citica hg
@darcdiego142 жыл бұрын
Hey everyone looking for parts for this reel, can someone point me in a good direction for them?
@danielrivas294 жыл бұрын
No reassembling it???
@arniecan85317 жыл бұрын
Where's part 2
@Green6sick66 жыл бұрын
So I just got one of these. Popped of the side with the break system and an extremely small spring and small axle type piece w/ part number bnt 4631 fell out. I didn’t notice it in your video. Any idea where it goes back in? The diagram states it’s near the open switch but not sure. Thanks in advance
@TheAleman035 жыл бұрын
Does the anti reverse bearing when inserted goes flush from the outsise end plate or inside of the end plate
@augustofernandes77774 жыл бұрын
Thais reel has a micromodule? The curado 200hg is to much better than this?? Or the difference is small?
@BeauReed4 жыл бұрын
Yes on th MM Gears. Difference is minimal.
@firgax7 жыл бұрын
hey i took my citica apart an cleaned it but it still has the problem that almost every cast even tho my thumb bar isnt engaged line still falls. anyone know hats the problem?
@barrywuthrich85304 жыл бұрын
needing to change out the anti-reverse bearing. No help here
@BeauReed4 жыл бұрын
Barry Wuthrich at the 3 min 16 sec mark the video shows the Sideplate being removed. At that point pull the A/R, and swap it for a new one.
@barrywuthrich85304 жыл бұрын
@@BeauReed Got it. Thanks.
@barrywuthrich85302 жыл бұрын
@@BeauReed The anti reverse bearing has a beveled side and an almost flush side. Which side goes towards the inside? Citica 200g series.
@BeauReed2 жыл бұрын
@@barrywuthrich8530 right handed reels are beveled out. Left hand reels are beveled in.
@sangpengembarafishing07114 жыл бұрын
Like friend
@jokrazy20027 жыл бұрын
I have Diawa Steez SV, non TW version. Cost $399. Can you clean, tune and put boca bearings. I can ship. I live in Fort Worth. How much, thanks. Check my page for reel I am talking about, I have a video on it. Thanks.
@netefrog6 жыл бұрын
Dude your work bench is dirty and nasty. Do you want all that grime and grit in the reel
@BeauReed6 жыл бұрын
NateRB this was a “how to disassemble” video only. Not looking for advice, but thanks though.