DIY Arduino Bluetooth control car with L293D Motor Driver, HC-05

Hello Guys in this Video Tutorial I am going to show you How to make DIY Arduino Bluetooth control car with Arduino Uno and basics components at Home.
🤗If you want to support my channel🤗 By Me a ☕Chai☕ -- buymeacoffee.c...
Follow me on -
WhatsApp Channel Link - whatsapp.com/c...
Instructables -www.instructab...
Instagram - / _elecobot_
Facebook - / 100077394460408
Arduino code for this car click the link below ---
drive.google.c...
App for this car--------
play.google.co...
Part-1 link -- • Android car/Bluetooth ...
parts list
Arduino UNO
HC-05 Bluetooth Module
L298N Motors Driver
LM7805 regulator
SG90 servos
dc motor
gears
2s li-ion battery pack
Also check this interesting videos-
Diy arduino rc helicopter p1- • Scratch built Rc Helic...
Diy arduino rc helicopter p2- • MUST WATCH !! Arduino ...
Diy arduino 10 channel Transmitter and receiver- • Arduino 10channel tran...
Diy arduino helicopter tail rotor- • Diy tail rotor for rc ...
Arduino rc helicopter simple structure- • How to build a rc heli...
Diy ORNITHOPTER 100% fly- • Diy flying Ornithopter
Arduino Monster truck full build- • Video
Arduino bluetooth control racing car DIY P1- • Video
Arduino bluetooth control racing car DIY P2- • Video
Thanks for watching.
Thanks to NCS for Background music.
Name Invincible Pt. II
Song by - Deaf Kev and Sendi Hoxha

[@PiyushDeshmukh_2]

Hey, I wanna make a drone just like you made a car. But im new to that, I have an esp32 cam module, please guide me further

[@elecobot]

So...to build a drone you need some components,those are A transmitter A receiver with pwm/ppm output(for this you can use your esp 32 cam mod) A flight controller(you can use another microcontroller or you can combine receiver and flight controller code) A gyro/accelerometer sensor(you can use MPU6050 mod) As esp32 cam mod has 10 GPIO pins with ADC you can use 4 GPIO for 4 motor/ESC and 2 for mpu6050 SCL & SDA. Esp32 is a small module so ..you can use 1020 model coreless motor or N60 motor or 180 motor or bigger bldc motors also. To drive those motors you will need ESC/electronic speed controller....for smaller motor you can use transistors like irfz44n or other. For big motor you will need ESC such as simonk/bl heli etc. As a power source a battery is required 3.7/7.4/11.1 volts lipo battery depending on your components/motor/ESC. FOR CODE you can use CHAT GPT.

[@elecobot]

You can follow this video kzbin.info/www/bejne/q6u9m55mibZ-qrcsi=CoutBMqSAfhE_y7Z

[@PiyushDeshmukh_2]

@@elecobot well, there is a list of parts I already have 2*esp32 cam module 2*dual channel drv8833 motor driver 1*1000mah lipo battery 4*n20 motors 1*mpu6050 Well I have all the least amount of parts to build it But the only problem is, I have two esp32 cam modules but operating and programming them is a lot hard for me especially as a beginner Well, I also have 2*nrf24lo1 module, but I accidentally powered them with 5v, now I don't know if they work or not. So, I'll be using esp32 as a reciever and a flight controller both with camera feedback and to reduce cost of building a transmitter.

[@elecobot]

@@PiyushDeshmukh_2you should cet new motors....because esp 32 weight 10gm,drv8833 is a 2 direction h bridhe driver(for drone one directional driver required) weight 2gm, with propeller n20 motors weight is around 10gm ....4x10 =40gm,mpu6050 weight 2.1gm,1000 mah 1 sell Li po weight is around 10 - 20gm, circuit-wires and structure weight around 10-20 gm.... So total weight is Around 70-100gm(depending on your components and structure) A single n20 motor thrust(can lift) around 20-25gm so....4x20=80 gm....while the minimum thrust is required to take off is about 5gm more than your drone weight.

[@PiyushDeshmukh_2]

@@elecobot so, I'll need CORELESS MOTORS huh?