DIY Vehicle Keyless Entry Alarm Installation Viper Avital Security System DEI GUIDE R32 skyline

[@daoz69]

Your video is the best video that I have seen, so far. You describe everything, and then the viewer can follow what you are doing. Other videos don't say much, they just do it. They don't explain the purpose of every connection and wire. Some of them are even mute. You have excelled over, provided us your knowledge and experience. Thanks!

[@Donnythelatemodeltech]

Thanks. I have a alarm video planned for the fall. Thanks again

[@OleUnreliable]

Watching this video made me finalize my order for a diy alarm. The shop was looking for 350 + tax to install, I think i'll attempt an install for that price.

[@Rutted4x4]

Absolute legend you saved me $600

[@Donnythelatemodeltech]

I like the sound, LEGEND , lol. 😃

[@SeanOMatic]

I like Avital because it's cheaper than Viper, but is the same exact stuff. Actually, I prefer the Avital remote on the 3305/5305 because they put rubberized sides on them and they are more durable.

[@HeadQuarterzTv]

Dude! This is great literally my alarm is all messed up and I didn’t want to take it to a shop as it’s mainly my street/track car so I’m pretty confident after watching this video! I have similar setup on the door lock stuff

[@Ihatemushrooms77]

Watched the entire video. Straight forward and easy. I like that the starter interrupt is within the module unlike a separate relay. On my car, I have a viper alarm. I added an automatic window roll up so when I set the alarm to arm and I had my windows down, they'll automatically roll up on their own. Or reverse the install and when disarmed the windows go down. That single orange wire is what send the trigger to the separate module to activate it. Pretty cool neat feature to have.

[@REXONATER70]

You convinced me to go get it installed. I’m not sure I could get it right like you did.

[@barrymonroy7138]

Come bro!!! First time for me. I'm not spending $700.00

[@pnw503bestcoast9]

Hands down the best video on alarm install! Thank you !

[@Donnythelatemodeltech]

Thanks for the great comment

[@ivanrivera9933]

Bro! Thanks🎉! Made my installation a piece of cake! I used my horn ,some quick wire connectors and some electrical tape.

[@santanaman6783]

You seriously made this look like a 2-3 hr job at most....❤❤❤ Awesome because my first gen diesel needs an alarm and im hope i can figure out how to delay remote start not just basic start....lol

[@gevinization]

Thank you so much for generously sharing your knowledge. It was very hard to find a good video out there, and yours is the best!

[@jdmchickkustomz9417]

I was watching your video because I put a keyless entry in a 99 Eclipse but then I saw your skyline had to say I love it!! ❤

[@Donnythelatemodeltech]

Oh wow!

[@g.tucker8682]

Outstanding! Just got a Viper 3100V, looks to be the same thing except the kit includes the siren. Thanks for the great info.

[@aarongibsonjr.9429]

Did you have to use a relay for the door locks? Or did you just splice the wires straight into each other?

[@slept-on_SP]

Idk why but other install guides were kind of hard to follow but this video definitely helped me successfully complete my viper install, much appreciated!

[@carlosgonzales1419]

This is the best installation video setup step by step I've ever seen. Thank you

[@Donnythelatemodeltech]

🤙

[@CLANSON]

Absolutely the best KZbin video explaining vehicle alarm installation!

[@Donnythelatemodeltech]

Thanks for the thumbs up 👍!

[@obtugtxivtub]

Thank you for the video. I am re installing the same one for replacement and adding the starter kill since the previous owner lost the remotes.

[@wmuhamma]

I have literally watched 50 videos of alarm installs but none as professional and detailed as yours….please keep up the good….also can you recommend a remote starter / alarm system that will work in a 2004 Toyota RAV4…….thank You for assistance.

[@insomnimike3453]

love how in depth this video is. 10/10

[@airfryerdeluxe5543]

Thanks for making this video. Just installed a Viper 3307VM in my 00' Civic and your vid helped tremendously. It previously had a Clifford Matrix 12.5X in there, but both remotes took a crap and eBay/Amazon had the discontinued remotes going for $120+. Figured this would be a good time to "upgrade" to a modern unit. Your video helped me make the new install much cleaner, as I was able to take some time to tuck wires where I wanted and each line was cut to length to where I wanted. Now I don't feel so discouraged to do an install lol, cause I had the alarm kit sitting for a while. Feels good to have a working alarm again! Thanks man

[@kylemcweeny878]

Learned it loved it now I gots the dough in the pockets 😌

[@thezofamilychannel7204]

Great video. It will be my first time doing an alarm install on my personal vehicle. I'm usually a car stereo guy. I hope i get it rite. I like using solder and shrink tube.

[@bronsonbradshaw2173]

Best alarm install video I've and I've seen alot lol. Thank for sharing your knowledge as well as simplifying for guy like me.

[@ZaneChandy]

Very descriptive and informative video. Thank you for explaining things nice and clearly for my slow brain, lol. You the man! 💪

[@thetimetravelerchannel]

Great video man! Nice job explaining everything and going over all the wiring harnesses thanks

[@Donnythelatemodeltech]

Thank you for the comment!

[@shafiqtrinidad8802]

Best video hands down!!!!! Simple and to the point keep up the GREAT work

[@Donnythelatemodeltech]

I appreciate that!

[@Bertoquest]

Wow you made it look easy

[@odeliogarcia4103]

Viper was considered the low budget auto alarm. It’s just that they have survived as other companies disappeared. I used to install these things. I would go to downtown L.A to the wholesale district

[@ECross.]

Whats a good alarm that you recommend?

[@sekou3758]

So why did the others disappear?

[@joeywitt7129]

BEST DIY ON KZbin!!! Btw I got a Hyundai Elantra (my son is taking it to college) so I have to het alarm which on u suggest btw they tried stealing it already if u got kia or Hyundai there being stolen at least 5 a night in Bakersfield. Let me know what one os best for Hyundai

[@hocelot3]

This awsome video gimme the courage to try to install the alarm on my Celica 2005 wish me luck guys

[@akfish8106]

Thank You ! got my key less/alarm installed today...,your video made it easier for me thanks !

[@jeff-JAO530]

Beautiful ride Bro! Nissan is #1 Thank you my Hardbody D21 is getting an alarm and kill switch.

[@aros007z]

Best damm video on KZbin for car alarm installation! You are great guy, awesome explanation!

[@claudiumihaiu7880]

This looked sooo professional.. I do have already a remote start japanesse one when was imported in New Zealand but not going anymore for some reason.if i add another one is alright or i really have to remove the old one first? I just can not find the wiring diagram for my car , Toyota Vanguard 2008,any help? Thanks alot

[@ElGhostPresents]

Can I use white/blue wire for truck release or is it remote start only?

[@joshephraim2592]

Do you have a video installing or going over the wires of the avital 5105L? I’m a bit confused on the Auxiliary/Shutdown/Trigger Harness, 24-pin connector

[@hermandiyproudlysa7703]

Thank you for the video, its very helpful. Im from South Africa and just bought a Blazer alarm kit. It has 2 brown wires for the indicator lights but only get power on one of them so only the one side indicator lights flashes wgen i trigger the alarm. Dont know why or mabe im going wrong somewhere. Can i use the one brown wire the flashes power and connect it to my parking lights and use the parking lights to flash when i trigger the alarm. Thanks

[@soldier2gud4me]

I have a question. Why is your video so great !!!

[@Donnythelatemodeltech]

Thanks

[@RanGer-498]

Avital was a big name bran back in the days

[@_raskalloko6445]

Is the door trigger wire supposed to be for both doors?

[@paddys455]

Where can you buy the relay with wiring that you used for the door lock actuator ?

[@elmel7896]

Very clear and helpful explanation. By the way ... is it possible to add proximity sensor to that Avital 3100 alarm system? I have open top car, so to have the car proximity monitoring is important

[@Donnythelatemodeltech]

I really don't recommend proximity sensors, they false alarm all the time to the point you ignore your security system . And to answer your question honestly I cant remember if the avital has the input for the external sensor, I leaning toward no.

[@knock904]

thanks bro very informative video ... makes me much more comfortable to install mine

[@sutharsanarasaratnam6341]

best video man helping me to do on my s2k. thanks bro

[@Donnythelatemodeltech]

🤘

[@amrikjaswal76]

Thanks for the video. Question...which wire would be for the power trunk release? My car has power trunk...would like to use the FOB to open it. Thank you.

[@sergeyprokofyev870]

Thanks for the great video! I have a question; is it possible to hook this up so that when you hit the unlock button once, it unlocks only the driver's door, and if you hit it again it will unlock the rest of the doors? I'm installing it on a base model(no factory remote, but does have automatic door locks) 2012 Toyota Yaris. When I open the car using the key in the driver's side door, the 1st turn unlocks only driver's door and another turn unlocks all the doors. The switch on the inside of the door unlocks/locks all doors at once. Thanks for your help.

[@JPS1223]

Where did you put the antenna wire ? I’m trying to figure out what to do with it ?

[@raamsesgomez2414]

So can this avital alarm system that you’re using in this video be used for any type of car?

[@knock904]

thanks for these amazing tips and tricks

[@HappySoulTraveler]

Thanks for this awesome content! I've watched it 5x. I purchased this alarm for my cargo and wanted to add additional shock sensor and tilt sensor. Where would I connect these additional sensors?

[@aa6546]

Awesome video👍 I have different model installing but so much info and helped me a lot! Thx very much🙏

[@xbmarc]

Great video. Very clear and straight forward. Thank you

[@Donnythelatemodeltech]

Thank you!

[@_raskalloko6445]

I bought a module that has a GWR WIRE (GROUND WHILE RUNNING) OR CHIP IMMOBILIZER, is it necessary to connect the wire?

[@barrymonroy7138]

So for the door tigger. Do you plug in to one door or both doors??? I'm hooking up to a two door 2003 Toyota Tacoma. Because i noticed that you hook up to just on door..

[@adalbertova]

Great video, very well explained and just install it in a 88 Toyota pickup and everything works just fine but I can’t get the horn to work, any suggestions what could be

[@Donnythelatemodeltech]

What polarity is the trucks horn wire? The alarms out put Is negative.

[@adalbertova]

@@Donnythelatemodeltech truck side is negative

[@bhogalandson]

Awesome video. I plan on using the same alarm. Did you have to use relays for your aftermarket door actuators?

[@Donnythelatemodeltech]

I used a 451m module. The video kzbin.info/www/bejne/jXnIg4d8jr56eJI

[@Donnythelatemodeltech]

New remote start keyless security video that comes out next week. kzbin.info/www/bejne/eqbdfHmGbriqgMk

[@bhogalandson]

@@Donnythelatemodeltech sweet. Thanks!

[@bhogalandson]

Quick question, I am putting the alarm unit in a maintenance work van. I have some LED lighting installed in the back of the van that is powered by 12v. Would it be possible to use the Aux function of the alarm to toggle the lights inside the vehicle to be on and off? Also, since the alarm FOB has a trunk button, can I use that to open my side and back door actuators separate from my front? Would I need a dedicated 451M for that?

[@Donnythelatemodeltech]

The back and side door is going to be tricky if it has oem power locks. If you have to install actuators you can use the trunk button.

[@JOKERBABYG]

Good video thanks for sharing 👍 I have a question my alarm system only has the wire for a siren and I don't want to use the siren, the siren sounds weak I want to use the horn instead but the siren wire doesn't work to trigger my horn what would I need to do to make my alarm trigger it with horn when alarm goes off?.. Thank you 👍

[@lawrencenisbett7579]

Great video I have the confidence to do myself thanks

[@oodles86]

What else would I need to alert if the trunk or hood is popped, or if the car is being jacked up?

[@emmanuelasare9103]

Hello Please what was the second website you visited?

[@frosty.jesus.gonzalez3800]

Did you use a relay for the alarm

[@adammara288]

Great video, do you have a link for that test light?

[@PNoYGuitarista93]

Would the channel 2 out put be used for remote trunk openers? Cuz the first gen CRV’s have that function on the factory key fobs so they can open the trunk

[@PNoYGuitarista93]

I would also like to know where I would connect a glass breakage sensor to the control unit

[@stevederek4810]

Nice vid mate. Im about to install an alarm in my pulsar. Im wondering how you went about hooking up that door lock actuator and relay if you happen to have a separate video on that would be awsome?

[@Donnythelatemodeltech]

Install Power Door Lock Actuators & Keyless Entry On Your Vehicle Tutorial / Skyline R32 gts-t kzbin.info/www/bejne/jXnIg4d8jr56eJI

[@jxaviers1]

By any chance do you know what are the door trigger wires to use for 2017 Mazda 3 sedan ? I can't find any info for that using the same Avital alarm. Thx

[@firewall8985]

My Kia soul I need to use both parking light wires to my one white wire on my alarm?

[@KL4life]

Excellent demonstration!

[@oggearhound2242]

Question: Is the yellow ignition wire needed to activate the starter interrupt? Great video btw! 🤠

[@dannycar25]

what are your opinions on T-Taps?

[@RlEL444]

Which horn Wire did you use? Brown with black or just brown?

[@tubejim101]

Great video. Do you have one on programming it?

[@davidgomez5116]

Does this one really need to be programmed?

[@fastm3980]

Great video. Thank you so much. I have a question can I connect negative trigger hood switch to the Avital System?

[@Donnythelatemodeltech]

Yes you can

[@Cristobal_300ZX]

Will this work for a 1990 Nissan 300ZX Twin Turbo? 2 Seater

[@reesef6030]

Maybe I missed it but what about the immobilizer or is that only for cars that are automatic for remote starting??

[@Donnythelatemodeltech]

That only applies with remote start

[@alexismariano1153]

Do we need to use a relay in order to add door lock actuators?

[@Donnythelatemodeltech]

Yes

[@drswigermd]

Not much of a wiring guy. Going to stalk this on my 87 C10. Can you explain to me the difference between a negative and positive trigger? With the ignition on, hitting the alarm interrupts the positive signal and this triggers a negative item? Such as a negative door trigger?

[@Donnythelatemodeltech]

This might help you out. kzbin.info/www/bejne/eqbdfHmGbriqgMk

[@MissTopDJ007]

Can you do a video how to disable the alarm valet switch when you don't have the key alarm fob?

[@DanielxxMoyo]

where do i buy the door lock relay my doors aren’t automatic either ?

[@freefall96]

Will the original keyfob from the car manufacturer work to arm and disarm the alarm or do you have to use the provided keyfob from Avital?

[@Gotham_City_collectibles]

Hello my first alarm ever. Just wondering if this will go off when the rear hatch is opened and is there a way to set it up to go off if the hood is popped. Thanks for the great explanation with a wonderful video

[@larrykhun9995]

Hey Donny great video bro. I got one question. I got a stock alarm and wondering if I go aftermarket will this be the same steps of installation? Do I have to remove the stock alarm?

[@iaguilera67]

I am curious why a right side drive car?

[@delonnelson6507]

I'm trying to wire my alarm to open and closed my car door but it doesn't work. My door doesn't have a lock switch I just lock the driver door and all door locks pull it up and doors open

[@MG-th9sl]

Great video. Makes me think I can do it myself.

[@Donnythelatemodeltech]

Go for it!

[@odessa9641]

Can I program avital alarm to my trafficator on my mirror so when I lock my car the mirror will light up?

[@mysteriousghost4852]

You're lucky with that starter kill wire, I'd have to go directly from the starter to the box; else someone could pop the hood, and short two studs and be gone lol.. Some thieves don't care that an alarm is going off and keep going.

[@diablo21236]

Would that same wire cut be for any car?

[@asaelmendez7781]

Do you have any link for the website???

[@msnow22000]

If I already have an Avital alarm (Hurricane2) installed and trying to replace it with another Avital alarm (3100L) since the wiring is already in place will it be easier to install? I lost my keys and no longer have a remote for my Avital Hurricane.

[@JJBanuelos]

Will have to attempt now. Thanks

[@samuelsaul4434]

Hi, I have 1996 Toyota Camry LE and recently loss my keyless remote starter entry , do I have to pay a mechanic for reinstallation or buy me a new and then get the old one out and get the new one in? Please help me with the best answer sir🤝

[@asaelmendez7781]

I can't find my car on the first website. Is 2018 gmc sierra

[@miguelbotello6.0]

I see you didn’t use a bypass module, is it because of avital itself? Or because the skylines back then didn’t have a immobilizer?? Thanks

[@Donnythelatemodeltech]

Because I'm not installing a remotestart.

[@joseconstante1321]

Question so I have a Cadillac DTS and I have a viper alarm connected to it and a sound system whoever hooked up the system did it wrong and is causing a drain I think theres wires connected to the battery i think its the system not the alarm but not sure could you tell me if any of the wires leaving the battery would be hooked up to the alarm directly because I am trying to disconnect the wires for the sound system I just don't know if they are it or it's the alarm

[@joseconstante1321]

It's kinda thick running to the back then there a black and yellow one that one is thin then there's another thick one that goes to a bolt all that is the ground

[@BenPeckover]

I went to the website but there was nothing for a 2003 Toyota estima

[@ronaldfeliciano9998]

Thanks for posting this video! It really helps a lot! Anyways, I have a question in regards to the truck unlock button on the remote. I purchased the same alarm on Amazon to be installed on a 2001 Acrua TL 3.2. I wired everything up like you did but I am currently stumped on how I would wire the trunk release so that I can use the button on the remote. There is a trunk release button in the car, so would I need to use one one of the other wires from the 12 pin connector? Would I wire the trunk release to the red/white white ( Ch2) wire or white/blue (Ch3)? Any input would be greatly appreciated.

[@isaiasvelazquezromero3468]

Hola para conectar el maletero debes de buscar en el diagrama cual cable es el que activa esa función puede ser positivo o negativo, ponle un relevadores y la señal tómala del chasis o de una fuente de 12 vol ,y la señal que te manda la alarma es la que cierra el relevador y abre tu cajuela

[@Ijustwannafixit]

Thanks for the video. Now I feel more confident in installing mine... I wanted to know if this alarm has a feature where you can just hear a low beep when arming or disarming it and use the horn when it actually goes off. Please let me know thank you.

[@Ijustwannafixit]

Do u know of any?

[@Kevin-wy8kc]

im not getting anything out of the green lock wire remote only works on the blue wire any sugg's?

[@juangalvan2331]

I have a 91 bmw 318is, where would you recommend it the best place to do the connection for the doorlocks?

[@cessers]

Thanks, Donny. My kid just bought a 2006 Taurus SE and I'll be giving this a go for her. 12volt does not seem to have the wiring guide for that model; where else would you look? Thanks again!

[@Donnythelatemodeltech]

Take a look at 2004 model. Should be the same. www.the12volt.com/installbay/forum_posts.asp?tid=60154

[@cessers]

Thank you @@Donnythelatemodeltech

[@cessers]

@@Donnythelatemodeltech ​ Install complete and it went great. Thank you!!

[@Donnythelatemodeltech]

@@cessers Awesome man!

[@felipegomez6188]

Quick question the avital model 3100L it will start your car from the remote control or not,,, ist just the same as the one on this video...... Good video i subscribed and give 👍 to you video

[@Donnythelatemodeltech]

It's not remotestart

[@felipegomez6188]

Thank you

[@mannyreyes2833]

I just got a atival 3305L and an going to attempt to install on a 02 Camry with stock power locks and keyless entry, anyways it is it necessary to use diods for door triggers because of dual zones feature or can I just hook up one zone