How to retrofit projector / puddle lights to Audi A4

[@diydaly]

Puddle lamp set including wires - ebay.us/VtZeZf S-line projector lamp set - ebay.us/ECeL9s Audi badge projector lamp set - ebay.us/WYamjI If your looking for reasonable price car parts check out these sites: Check Euro car parts - tidd.ly/3lIO7xA (use discount codes on site) Check GSF Car parts - tidd.ly/34pZe7o (use discount codes on site) Check "Car Parts for Less" - tidd.ly/2LNEwIn (use discount codes on site)

[@adrianthomas2042]

Thanks

[@kwestmc1679]

Hi mate, great video👍👍 I have a question I haven't tried it on the front door yet but I've already tested it on the rear door and it didn't work.... I have the b7 2006 2.0 tdi In the video, when you finish the front door the light comes on immediately, but when you finish the back door it doesn't light up immediately, there is a cut in the video and you can't tell if you do anything to activate it, is there anything that needs to be done ?

[@diydaly]

No everything should work , it was a long time ago that I did this I’m afraid so I’d have to look back

[@GCS88]

Great job something I would do in the future

[@diydaly]

👍

[@hakgar]

Nice detailed information. Thank you!

[@diydaly]

Glad it was helpful!

[@JamesSquires-r7n]

Hi i have a audi a4 2009 b8 and i have fitted my lights but need to no were to put the wire that clips in to u put urs in number 13 what number will i need to put mine in on the front and back thank you

[@johngibraltar]

Hi great video , can you tell me what terminals I should connect to on a 2008 Audi A3

[@diydaly]

I’ll try find out

[@johngibraltar]

Thanks

[@rafaloldak5577]

Thx Mate good job 👍

[@diydaly]

No problem 👍

[@hitesh2683]

Hi, Thanks for the video. I have Audi Q3 (2018), it has the slot for Projection Light, same as showing in your Vidoe, means it will require to cut the plastic part. Could you please help me, if there is Garrage, who can install these.

[@diydaly]

I’m sure some one will do it , but I’m not sure where in your area tbh mate

[@michaelshortt4313]

I have a 2007 b7 sline, is the pins the same as this video? I’ve bought s-line projectors

[@diydaly]

Yeah yours will be exactly the same mate 👍

[@chriswinters6771]

Does this projector work only when you have opened doors? Or it gives light all the time?

[@diydaly]

Only when the doors open mate

[@chriswinters6771]

@@diydaly Thank you very much and thanks for detailed video :D

[@diydaly]

@@chriswinters6771 👍👍

[@zeRaxx]

Could I make the harness myself with the correct gauge of wire? Anything special to it? I would probably put some different connectors on for the lights.

[@diydaly]

Yeah you could do mate, wouldn't be too bad to do 👍

[@adrianthomas2042]

Hi. Could you please help. I've boughy some Audi logo puddle lights to put in my car which doesn't have lights there at the min. Would you be able to help and advice me on where I would be able to find the wiring. Thanks

[@diydaly]

Hi , is yours not the same as in the video then?

[@adrianthomas2042]

@@diydaly hi. Yes mine is the Audi Quattro A4 Black edition 2015 not sure what year the one in the video is. And I do apologize as I'm not really up to date with utube and technology

[@adrianthomas2042]

@@diydaly mine do have the red reflectors in but would have to make a hole for the underneath ones

[@diydaly]

@@adrianthomas2042 are yours is the later shape then , this is for the B7 model .. I’m afraid I’m not sure of the wiring for the later model mate

[@adrianthomas2042]

@@diydaly yes m8, it's the B8. No worries thanks anyway

[@lewiscrawford1679]

Going to attempt this on my A3. Ordered the wiring, does both red and white lamps connect to the one cable ?

[@diydaly]

Yeah they both go into the same loom mate 👍

[@lewiscrawford1679]

@@diydaly Great thank you. First time trying it but your guide is really helpful thank you 👍

[@diydaly]

thanks for the comment, much appreciated ... im sure you'll suss it out mate 👍

[@lewiscrawford1679]

@@diydaly I’ll post pictures once completed. Also other videos are good education also for car folk 👍

[@diydaly]

👌👌👍

[@CorneliusBane]

One question more, what is number of this pin you used? I found 000979018e and 000979009E. Thanks :)

[@CorneliusBane]

Shit, I meant connector :D

[@diydaly]

I can’t quite remember tbh , will try find out

[@CorneliusBane]

@@diydaly I used this one "000979009E" works fine ;)

[@diydaly]

@@CorneliusBane 👍👍

[@robbooth8184]

Hi mate great video. I’ve got an Audi A4 2007. Would this still be the same wiring loom?

[@robbooth8184]

It’s saying on eBay that this doesn’t fit my car? It’s an 2007 Audi A4 avant.

[@diydaly]

Thanks for the comment 👌👍 . Is yours a b7 or b8 model, 2007 is right on the change , if it’s a b8 yours may be slightly different

[@robbooth8184]

@@diydaly it’s definitely a B7.

[@diydaly]

@@robbooth8184 if it’s a b7 it will be the same , I’d say because it’s close to the cross over they probably just list up to 2006 that’s all

[@robbooth8184]

@@diydaly can you give any tips on soldering?

[@martinash4131]

Is it same for passenger side ? Got driver side working but cannot get passenger side to work?

[@diydaly]

Yeah should be exactly the same mate

[@martinash4131]

Hi have done it all the same so I don't get it??? Must be a problem with the loom will have to get a new one I think but thanks for the vid it helped 👍 alot

[@diydaly]

@@martinash4131 👍 hopefully you get it sorted

[@MrPIEEYEDPIPER]

Are they the same pins for a 2008 B7?

[@diydaly]

No I think they are different on the B8 mate

[@MrPIEEYEDPIPER]

No mine's still a B7, one of the last.

[@diydaly]

Are sorry mate! I read it wrong! Yes it will be the same 👌👌👍

[@MrPIEEYEDPIPER]

@@diydaly does the light set you linked to definitely fit B7 wiring? The link goes to a set that says A4 2008-2014.

[@diydaly]

@@MrPIEEYEDPIPER hmm ill have to double check that, I wonder if they have changed the listing..? ill havre a look and alter if need be

[@yunusemreyalinkilic9676]

can you please write the link code on the driver's door thanx

[@diydaly]

sorry do you mean the Ebay link?

[@yunusemreyalinkilic9676]

no,driver door lighting need pin code

[@yunusemreyalinkilic9676]

there are multiple cables

[@yunusemreyalinkilic9676]

driver's door

[@diydaly]

@@yunusemreyalinkilic9676 I will try find out for you, its a while since I did it 👍

[@racons2894]

Witch one of the cable is +

[@diydaly]

it was a while ago I did this, wouldn't know without rechecking mate

[@johndillingham3679]

Hi mate. You’ve said “shouldn’t “ need coding. Did the car run ok once you’d finished? John 👍

[@diydaly]

Yeah all fine mate , I’ve done 4 sets now and none required any coding 👍

[@ثامر-ظ3ض]

Great bro💚

[@diydaly]

Thanks mate 👌👍

[@ibi2227]

Mannnnn, been messing with this for too long already. Fitted them and they turned on alright. Put everything back together, screwed everything back again and they ain't working anymore. Can't wrap my head around it...

[@diydaly]

🙈 haha that’s a paint! Are you sure there’s not a wire broken in the door joint

[@ibi2227]

Yeaaaa, I feel kinda dumb lol. You'd seen me rage quit last night 😂 turns out ( I should've known) that if you'd working on the car doors ( open) they won't turn on unless you shut the door and wait another 5 minutes.... So i did everything twice..

[@jayykelly3621]

Does this need coding in? I’m planning on doing this on the weekend but have no access to VCDS, great vid btw👍🏻

[@diydaly]

Hi mate , no shouldn’t need coding, it’s just plug and play 👌👍

[@jayykelly3621]

@@diydaly thanks👍🏻

[@diydaly]

@@jayykelly3621 👍