Dji Digital Fpv System install with crossfire frsky spektrum and more

[@The1stJesusMachine]

Great informative video. Not enough DJI hybrid builds that include the betaflight steps. You seem like a great down to earth guy and deserve way more views!

[@EricBartolo]

newbie question but what do I need to make the DJI FPV work with a Taranis X9 lite radio? Thanks!

[@cappafpv]

Eric Bartolo nothing, they are independent systems so you would just hook each one to the quad like normal and fly

[@EricBartolo]

@@cappafpv Thanks for the prompt reply mate! If I buy a pre-built quad from iflight BNF with DJI FPV, can I just buy the DJI goggles and connect the quad with the Taranis X9 lite radio + crossfire receiver? Thanks

[@genxdrones]

man i love the vid.

[@SilentlineProduction]

Did that connector for receiver to airunit come with the airunit? Or did u have to buy that separately?

[@manfrombkk]

What would be the practicality of using this system with an RC truck. Would it be possible to use the DJI controller in place of the RC controller that usually comes with trucks (Arrma / Traxxis). I am not sure how that could be done, as it seems like the DJI controller is only compatible with BetaFlight, which I assume is only relevant to quads. Just wondering, since the controller paired with the camera supposedly provides additional range. Any thoughts on this would be welcome.

[@cappafpv]

No-Motion well it could work. I’ve used my frksy taranis on my rock crawler. DJI system uses sbus so as long as you have a board that converts sbus to ppm I believe it will work. I have done this before

[@zimzillakilla]

You could setup the fc board to control servos.

[@manfrombkk]

I was just thinking it would be cool to mount the DJI FPV camera and air unit somehow inside and back behind the windshield (maybe would need a small hole cut out in the windshield. then you could just use your own Traxxas Transmitter to control the car, but actually be looking thru the camera in an HD view, as if you were actually inside the car. Like a real driver of a real car would do. Just some thoughts. I am sure the RC community will look into this, as the system is certainly not just intended for quad copter uses.

[@emilianozapatta5978]

I ordered complete packages direct from DJI ...excited !

[@ktmjay9920]

Would rear stand offs not fit?

[@a.i.thinker4059]

Really cool of you to share man Thanks!

[@dstepsfpv]

Thanks to Share, I bought the googles and 3 units for my drones, I'm gonna use my FRSky controler. But I have a big question?! Any time I want to Change the drone I have to rebind the googles with the unit?!? Or it saves the bind of my 3 units/drones?!?

[@cappafpv]

DSteps Pilot mine saves the 2 air units and it links to the first one powered up if that’s what your asking.

[@cappafpv]

DSteps Pilot I don’t have to rebind every time I switch quads

[@dstepsfpv]

Yap, mines to, just Discovery after testing all binds

[@dstepsfpv]

@@cappafpv now I have a little problem, I'm a bit confuse with the rssi Signal....its not stable like I have on my analogue kwads....the rssi signal on my Dji drone is a bit crazy....I dont know if I setup properly or what.... daaaaammmm....

[@cappafpv]

DSteps Pilot that I don’t know. Your using the DJI radio or no? It shouldn’t have any effect with another brand radio.

[@allennickles3970]

Awesome content.. keep it coming

[@cappafpv]

Allen Nickles thank you

[@HomeGrownCanadianFPV]

beautiful build brother.... helpful too... ty

[@coltersmit]

What is your full drone setup

[@AmigoEzio]

How did you pair your transmitter to DJI air unit?

[@cuneoism]

How can I connect my FRSKY X9d plus with the digital fpv?

[@cappafpv]

Luciano Cuneo I’m not sure what your asking specifically. This setup is using the DJI with a taranis. The DJI system is only a vtx and camera. The video is hooking the camera and vtx up. Maybe I’m missing what your asking.

[@cuneoism]

@@cappafpv Thanks for the response! I am new to the FPV game so I just wanted to make sure what I would need to purchase besides already having my X9d transmitter and the DJI FPV Digital System. I am thinking of getting a Cinebee 4k that comes with Frsky X-RS receiver but I am not sure if that would be compatible with what I have per say. Any suggestions?

[@cappafpv]

Luciano Cuneo if you are buying a bind n fly then you would remove the vtx and camera from the bnf. It doesn’t sound like nothing else is needed.

[@paulmccleary6875]

How does it fly without the rear standoffs?

[@CherylKCherylsHomeCookingshow]

Thumbs Up......Awesome job!

[@jrisinlove]

Wow fast and clean soldering. What are you using

[@cappafpv]

Javier Ruiz thank you 60/40 rosin core solder. Nothing really special. If you are having issues soldering try a different solder and flux works wonders. The thin 60/40 is awesome to use

[@jrisinlove]

@@cappafpv thank you! I will look into it.

[@vergil9397]

Can i solder white and gray wire on tx3, rx3 and turn on UART3 ? im new to fpv

[@steadywhoop]

Thanks for video ! One question please : why didn't you connect directly the module + and - directly on a 10V solder pad + and - on your FC ? IN such way no need the Matek converter

[@cappafpv]

Cine Whooper my fc only had a 3.3 or 5volt pad. I run 6s so I needed to step it down

[@filmmakerstudio3919]

@@cappafpv ah Ok ! Thank you. Wait for your test video and your feedback :-) Thanks for all your informations, it helps

[@cappafpv]

Filmmaker studio I am in the process of editing it now. It’s just a pain because it’s 3 cameras to edit into one video lol

[@steadywhoop]

@@cappafpv Let's see the result; are you happy to this DJI product ?

[@cappafpv]

Cine Whooper not really. DJI has mine locked to 25mw and I can’t get in out. Waiting for a day so far for something to happen

[@azdronedude]

Great video where can I buy the long LED you used in this video

[@alaingosselin8764]

Nice 👀👍

[@did3d523]

are in fcc or CE country?

[@GavDoG7]

Great post! Really helpful to see each of the steps you went through to install. Have you done anything special to secure the antennas? I see you cable tied them to one another, but mine feel like they'd just fall out. I'm thinking they need to be secured to the unit too

[@cappafpv]

Gavin Edgley I haven’t had a chance to design a tpu mount as of yet. Yesterday I just got it fully unlocked. I want to make something for this frame to make it fit a lot better

[@novavin1140]

@@cappafpv hey, i'm building my first drone, how do i know what port i'm in??(usb, Uart1/2/3/4, etc)

[@DarkZenonia]

Where is your flight test

[@prrcpor]

Nice frame. It's like a Cadillac. Hey have u tried this system at nigh yet?

[@rttt284]

How can I buy them online ? Dji Digital Fpv

[@cappafpv]

RT TT banggood has them I have a link in the description

[@albertsong1570]

actually, DJI's controller has lower latency than crossfire, it's 7ms

[@laurenthenry]

Yeah but apparently the Crossfire is better for lang range and thru obstacles. Is that true ? Anyone agree or disagree ? I have already the Taranis QX7 and don't wanna buy the expensive DJI remote. Thanks :D (and I'm a big noob on FPV, go easy on me please ahah)

[@benavitchvonsurfalotte3940]

Crack open that flight module box and get the guts out. Its going to be way smaller and lighter. Everyones complaining about the size but nobody ive seen has gotten rid of the bulk..

[@MrFullSend]

it's a heat sink - you need it. Air flow might help, but the components get hot, so I'm not sure you can remove them - maybe I'll try.

[@timrodriguez1]

🤠👍

[@JohnIn2SonAZ]

So your using that huge box with the VTX and Receiver as a HD VTX only. real waste of money on my opinion. And a huge waste of space and weight. Wait for the Fatshark. It will be a much more efficient and less costly solution. Plus I can't stand DJI. So no thanks.

[@boratsagdiyev1586]

the fathark one requires groundstation not a module.

[@JohnIn2SonAZ]

@@boratsagdiyev1586 Exactly what I would want.

[@boratsagdiyev1586]

@@JohnIn2SonAZ I cant see the benefit of that