Please check out our site for parts and repairs droneoptix.repair
@cosmos196213 жыл бұрын
Best teardown viddy yet. Thanks, many questions answered especially as it relates to screw placement.
@TheRaisham3 жыл бұрын
Hello there. Can show how to disassemble the MAVIC AIR 2 REMOTE CONTROL. TQVM.
@matheworman63082 жыл бұрын
Bravo the best Tear-down video on YT...
@droneoptix52182 жыл бұрын
thank you so much for your comment :)
@srikesh93 жыл бұрын
Hi can you make a similar video on putting back all the disassembled parts and getting the drone in working mode ( And can you pay special attention on soldering of the wires on mother board ) ?? Thank you
@dariusveseckas90593 жыл бұрын
Just watch the video backwards
@fabitobogota3 жыл бұрын
Hello, excellent video. I would like to know if you have any part of mavic Air 2s. I need upper front vision module. Thank you
@rgassaway86144 жыл бұрын
Very informative and helpful. Thanks
@visionmediaproductionsnz3 жыл бұрын
Can you please do gimbal teardown?
@723lperal33 жыл бұрын
Do you have a teardown of the Mavic pro would love to see one and how do you take the bell housing apart need to clean it
@germanstepanov36224 жыл бұрын
Thank you)
@fishesfromtupperware4 жыл бұрын
Thanks for the vid!!!! Very helpful replacing both left arms! Might want to mention that you need to put the front shoulder joint (?) in the half way position when reinstalling to preload it. Also I found if you pry up slightly on the ears (?) at the rear of the top shell, it comes off MUCH more easily.
@SuperAirman244 жыл бұрын
hi mate, can you please run me through this half way position? like does the armm need to be in the open position? also what are you using to turn the joint. ive been stuck for a long time now. thanks
@fishesfromtupperware4 жыл бұрын
@@SuperAirman24 The rotation shaft is the little silver "can" with black plastic tee on the top (looks like a servo arm) You can see him pushing it out at (3:34) and the other arm's joint is on the table near his middle finger knuckle. Its the pivot and connection point for the front arms. Hold the "can" gently with a pair of pliers and with another pair to hold the arm. Rotate it gently and you'll feel it lock into position every 180 degrees. By "halfway" I mean the point between locking positions. It'll hold itself there if you're careful. Then install it on the drone with the arm partially open (it only fits one way) and push it down onto the tits where the black arm seats. Clear as mud huh? I've got one coming in tomorrow and I'll post a vid. If pictures are worth a thousand words and a vid is at least 10k. cheers
@SuperAirman244 жыл бұрын
I was able to figure it out but man it was a pain to put back.
@SimoPortti2 жыл бұрын
4:35 are the cords on the led of the landing leg a clip on or do they require soldering? I managed to crash my mavic air 2 and the leg broke. The antenna cord is still intact BUT the two led cords have disconnected
@FoxHotelLima4 жыл бұрын
Nice video thanks! I have been doing some comparisons between US and EU model to find out the ADS-B hardware. I cannot find anything different between the two models. As per DJI, US models come with ADSB rf circuit and additional antenna and a different ESC powerboard
@ad.drones.42 жыл бұрын
Melhor vídeo até a o momento de desmontagem sem danificar o aparelho . Parabéns.
@eduardongc3 жыл бұрын
Hello, excellent video, can you confirm where exactly the compass is located? Thanks
@imad27753 жыл бұрын
Hello, is it possible to install an HDMI output in the Mavic Air 2 drone so that you can stream directly from the camera to the TV or PC? Thanks in advance
@droneoptix52183 жыл бұрын
This can be done by an app, or perhaps plug from the USB port on the RC.
@jym18554 жыл бұрын
Does it have two antennas? One in each front leg? Or just one?
@eduardongc2 жыл бұрын
Hello, very good video, I have a big doubt, I want to know if you know where exactly the compass is located in the Mavic Air 2, I had a similar doubt with the compass of the Mavic Air v1 and after investigating more than 6 I was able to confirm that it was located in the main board, that is, it is integrated with the board. Do you know if the same thing happens with the Mavic Air 2 version? Thank you
@AF-hx4xz3 жыл бұрын
What are the blue things on the bottom shell towards the rear? I’m not talking about the LED lights or the sensors but the mirror-like things
@juanmamusic31563 жыл бұрын
Wao!!! Buen video bro!
@sahidsingh-jw3rh Жыл бұрын
Good video sir
@bvill67492 жыл бұрын
where can I get tools for the magic air 2S. the one I bought from amazon cam with stripped bits now its too late to return.
@benperkins104 жыл бұрын
Thanks very helpful video, keep it up :)
@michealbester3043 ай бұрын
Where is the Compas located?
@skylurkerph2 жыл бұрын
hi do you have idea if the air 2 core board mother board same with the air 2s mother board? can they compatibly replace each other? thanks from the philippines here
@sahidsingh-jw3rh Жыл бұрын
Hello. I bought a wrecked drone online and it is binded to an other acount. Would you recommend to change the motherboard in order to fix my drone or do I have to change other parts as well? Thanks
@yomisaheed92106 ай бұрын
My dji drone of mavic air 2 GPS board has damage that make drone to fly .pls how can get a new one I mean GPS board
@KaneLono4 жыл бұрын
Question about the bottom cover on the Mavic air 2... There are two round sensors on each side of the LED. When you take the bottom cover off, do those have glass in them or are they just empty holes? In other words, is there supposed to be glass covering the glass sensors? Thanks
@СергейМитютькин4 жыл бұрын
Does anyboby know what processor (or SoC) is installed in subject?
@seavil13 жыл бұрын
what type of motor is it? Schematics?? size and power??
@droneoptix52183 жыл бұрын
its a brushless motor DJI do not release schematics, if the USA push the right to repair bill and legislate we may get some then, size and power can be found in the specs of the drone on the DJI website :)
@brokensword26213 жыл бұрын
very cool man
@jbcom24162 жыл бұрын
Very thorough tutorial! One question, will any disassembled part require a calibration with special software after everything is put back together?
@AudioStorm19802 жыл бұрын
I believe that all the calibration needed is the one where u turn the drone.
@burnagiewebbe9182 жыл бұрын
Where can I find the vibration absorption bracket for the mavic air 2? Any help will be appreciated
Hi how to disassembled motor and clean it. There are a sand
@jonathanjames66934 жыл бұрын
Where can I get the front cover? Mine is bent and requires replacement. Please help!
@droneoptix52184 жыл бұрын
Hi, we have one here www.droneoptix.repair/product/brand-new-and-original-dji-mavic-air-2-front-plastic-cover-genuine
@Jeff.35mm4 жыл бұрын
Just crashed mine after connection error now i need a replacement camera signal line connected to the gimbal
@artemkhol73214 жыл бұрын
Hi DroneOptix, thank you for this guideline. Really appreciate. I have some questions. Basically, due to new European regulations, I need to decrease 570 grams weight of the Mavic Air 2 to 500 grams. I have an idea to get rid of avoidance sensors (Front,Down,Rear). Related to the above, the questions as follow: 1. Is there a chance to measure the weight of each module are shown in the video: - Front vision module (2:27) - Down vision module (1:02) - Rear vision module(4:10) 2. What are the parts may be considered as redundant? Just in case if avoidance sensors will not cut 70 grams. 3. In case I remove 3 mentioned modules and disable the avoidance sensors in the setting of the app. Would it be working fine? 4. Is the a chance to remove - Rear vision module(4:10) without unsoldering work? Thank you a lot for any information. it will help me a lot to make a decision. I believe for many people in Europe that would be helpful, due to the new European restrictions (valid from 1 July 2020) with drones above 500 grams. Thank you a lot
@droneoptix52184 жыл бұрын
Sorry, but we don't have all of the parts in stock right now to carry out that weighing. We also don't know if the drone will still work without those sensors, but it should.
@linzz80744 жыл бұрын
Can you teardown the gimbal too ??
@droneoptix52184 жыл бұрын
Yeah, if people want to see that in a future video please like this comment or add another comment and if we get enough requests we'll make one. These videos are pretty expensive to make though as they take a lot of time to do properly - this one took about 15 hours!
@FoxHotelLima4 жыл бұрын
@@droneoptix5218 Yes It would be nice to see gimbal teardown. This video is even better then ifixit
@peterh81984 жыл бұрын
can the gimbal be replaced/repaired without purchasing an entirely new camera?
@ollyperkins4 жыл бұрын
Yes it can, unfortunately most of the parts aren't avaliable to do it yourself.
@Maravistudio Жыл бұрын
India me aa jayega
@FabianoMedeiros6 ай бұрын
What about the cam? :(
@jameslee13453 жыл бұрын
at 0.18 timeline, when you remove the bottom, do you see sealing to those screws to prevent unauthorised unscrewing so that once remove, warranty will be void? I suffer warranty void because of simply accusation of missing seal caused by me.
@RadhwenKhelia3 жыл бұрын
Hello, Same over here ! Did you find a solution for this ?
@WaspinatorNetworks4 жыл бұрын
I have a question where is the ads b in ma2
@structuralelement9834 жыл бұрын
this is a better teardown than ifixits. proper.
@droneoptix52184 жыл бұрын
Thanks so much for the feedback, it's really helpful. It's just a shame that their video became so much more popular.
@coachfredz704 жыл бұрын
Is it easy to tear down the landing gear stand? Just concern, if I need to replace this part, does the LED come out easily or do I need to desolder the wires to remove it from the housing?
@droneoptix52184 жыл бұрын
Hey, The LED can be pulled out without soldering
@bvill67492 жыл бұрын
Is it the same for the Mavis air 2S?
@droneoptix52182 жыл бұрын
the air 2s is different
@Lours4114 жыл бұрын
Do you ship parts to France?
@droneoptix52184 жыл бұрын
Yes we do
@Jerry235553 жыл бұрын
Need mavic air 2 mother board
@xgalaxyone4 жыл бұрын
I crashed my one of my rear sensors, is it easy to replace it?
@droneoptix52184 жыл бұрын
Yes, it's really easy, so long as you are happy taking the drone apart like shown in the video. We have them here - droneoptix.repair/product/brand-new-and-original-dji-mavic-air-2-backwards-vision-module-sensor-genuine they'll be in stock very soon.
@kasimsemihoz4 жыл бұрын
Hi, ı Need Mavic air 2 gimbal camera? Con you help me
@droneoptix52184 жыл бұрын
Hi, yes we have one. The full camera gimbal is £299.99. We are getting them listed soon, but if you want to reserve it please pay the money through this page - www.droneoptix.repair/product/pay-a-bill
@droneoptix52184 жыл бұрын
Hi, we have it marked in stock now here - www.droneoptix.repair/product/brand-new-and-original-dji-mavic-air-2-camera-and-gimbal-assembly-genuine
@forzax29303 жыл бұрын
Motherboard,gps,cameras,sensor,powerful motors,those reasons dji drones are very expensives