DK Customs catch can for Harley Davidson external breather

[@oldasdihrt5993]

Thanx for the brake reservoir tip. I was searching amazon for gas filters that would work. No luck. You saved me a lot of aggravation. Thanx again.

[@impoppa9647]

Awesome, I have a full filter / breather / catch can system on order and this video has been excellent for help and ideas on what to do with the catch can location.

[@2HotWheels]

Cheers for the tutorial, considering the Dk Catch cans are now $140, i will be making up own using the ebay part

[@adminadmin9997]

You should do an update video on this showing what you caught in the can after an X amount of miles

[@TheGingybeardMan]

Certainly will 👍

[@TheGingybeardMan]

TAKE NOTE!!! I only had the DK customs catch can on the bike for 1500kms. In that time 1/4 of the can filled up with an oily condensation. The thread inside the catch can which holds the filter element started to rust and deteriorate badly. I Would not recommend a catch can as it can also pressurise due to the breather holes being extremely small. If you do an external breather mod I'd definantly recommend going with a pod filter instead 👍

[@BlancoFlaco]

Are you keeping it in the same place or rerouting back to kits original spot?

[@TheGingybeardMan]

@@BlancoFlaco I got rid of the catch can and went back to the pod filter the way I had it before.

[@BlancoFlaco]

@@TheGingybeardMan k 👍🏼

[@flyinlow6692]

Pretty cool mod bro, I think a steel braided line would look dope. Keep up the good work...

[@TheGingybeardMan]

I was thinking that myself man, I'll probs end up changing it in the future to a steel braided line 👍

[@chrissmith7669]

I like how the black disappeared into the engine. Stealth mode. :-)

[@YeahNahMaybe947]

Great video just facts concisely explained with none of the usual BS to stretch the video out so they can fit two 6 second ads in, thank you...

[@johnjubie7144]

Great job, right up until the hose clamp!!!

[@coryhawkins967]

I installed one right before a week long trip over 1300 miles on my 114 street bob and when I got home it had just a little bit of oily water mix in the bottom and the treaded piece in the middle was covered in rust. I ended just venting it to the ground because honestly it’s mostly just condensation coming out of it.

[@TheGingybeardMan]

Yes sir, that's why I pinned a warning note at the top of my comments. The DK customs catch can is no good

[@FreedomRider1982]

Hello from Florida, USA mate. Just came cross your channel. Checking that previous video you mentioned now....👍👊

[@RoadRashHD]

DK is making some good products

[@adenclarke2853]

Great job as always Gingy

[@rickhensley5734]

Always great content man. I just bought a complete take off Ventilator for $85 on Facebook. Had it powder coated. Gonna put my own spin on this mod for my ‘19 Bob. Thanks for the inspiration. Be safe out there!

[@TheGingybeardMan]

Thanks mate, $85 is as cheap as chips, good find 👍

[@rickhensley5734]

@@TheGingybeardMan it was a steal. Even had the air filter with it. Lol. What's next for your Bob?

[@TheGingybeardMan]

@@rickhensley5734 mate it'll probably be the tank upgrade, but I'm even thinking bout switching out the rear fender as well.

[@rickhensley5734]

@@TheGingybeardMan have you thought about a wider rear wheel/tire to go with the fender?

[@TheGingybeardMan]

@@rickhensley5734 yep I've definantly considered that and will get a wider rear fender to suit a larger back wheel. I'm just looking at a few different types of rear fenders and I'm not 100% on which style I'll go with just yet.

[@MarvFitBikesKicks]

Damn dude that’s a clean ass job you did there. Looking to do this pretty soon. Thanks for the tips

[@TheGingybeardMan]

To be honest I wouldn't recommend the DK customs catch can. After only 1000kms the thread inside the catch can rusted terribly. The small pod filter in the 1st vid is the best route.

[@RobertB56]

I did the same except mounted the catch in the same place,looks neat I used the CNC brake reservoir in the link 22 AUD delivered,I did my plumbing different to you as my screamin eagle 🦅 stage one air cleaner was easier to mod than youre, anyway really happy with the outcome,thanks for the help,hope the Yammie is going well.

[@TheGingybeardMan]

Good stuff mate 👍 the Yammie is going great guns

[@theslowride4948]

On ya Gingy. Bob is coming along nicely

[@TheGingybeardMan]

Thanks mate, I'm slowly getting there :)

[@bmp72]

I had a beercan for this purpose duct taped under the tank of my Moto Guzzi. Just stuck the hose in there. On shutdown it would gurgle from this can...

[@dmenaced]

Nice vid. Very creative!

[@renatodelogu9214]

Hi, what did you make the sleeve from and how long is it?

[@AnarchistBogan]

I would love to do this mod too. And eventually tune my bike on a dyno with a cam too hopefully. I feel like my bikes got an EPA “compliant” tune...

[@TheGingybeardMan]

Go for it man, it's an easy enough mod to do 👍 saves your engine having to burn hot oily mist so will help with performance.

[@daviddawson4453]

Very good presentation,

[@gregbrooks5870]

I wished you would have run the breather hose behind the rear pushrod tubes nice video thanks 👍🇺🇸

[@TheGingybeardMan]

I've since ditched the catch can as it started to rust on the inside after only 1500kms

[@cdnrider6200]

@@TheGingybeardMan The DK catch can? What are you using?

[@TheGingybeardMan]

@@cdnrider6200 yes the DK custom catch can did not hold up well the threat inside the lid started rusting badly. Im now running the pod filter which I used in my 1st vid of the external breather

[@cdnrider6200]

@@TheGingybeardMan was that a k&n pod filter? I have already purchased the catch can from dk LOL but i will be putting it in a not so noticeable spot .....take care dude

[@bobgibb2781]

Thanks for the money saving tip about using a brake reservoir . What's your opinion regarding any existing carbon build up after the mod is done ? Do you you think it will eventually burn off ?

[@TheGingybeardMan]

I don't think the existing carbon will burn off due to the way it hardens. That said it's still good to do to prevent excessive carbon from building up

[@jimzacame3922]

Run Sea Foam through it. Carbon gone.

[@bap2139]

wait why did you swap the filter with the catch can? don't they effectively do the same thing?

[@markwilkinson2389]

Wow, I thought I was bad. Your attention to detail has made me jealous. Well done !

[@TheGingybeardMan]

Thanks mate, this thing is my baby, I love working on it and making it my own 👍

[@scottbradshaw5249]

Won't oil come out through the holes in the top of the catch can and be all over your exhaust pipe? I had mine under the air cleaner and it was coming out and flying all over my exhaust pipe.

[@TheGingybeardMan]

@@scottbradshaw5249 I didn't experience this. Inside the catch can is a small foam filter that absorbed all of the oil.

[@skarekrow101]

You getting any oil accumulating on the top where you drilled the vent holes? I did this to my bike and it's getting oil accumulating on top where the vent holes have been drilled out.

[@2HotWheels]

Thats happening because the oil is following the path of least resistant. Im thinking of drilling only 1, maybe even 2 holes max

[@haroldbible44840]

I'm out of the USA they don't ship to us. Do u know any way to find a usa seller that handles these for us to purchase the clamp bracket.?

[@wb4514]

What is the home made can called and where did you get it ?

[@larrikinlancer685]

So, what exactly is a catch can for and can I do this for my Fxlrs?

[@TheGingybeardMan]

The catch can catches the only residue which would otherwise go into your intake. Yep you could do it to the low rider S but I'd recommend running a pod filter and not a catch can. The catch can rusted pretty badly on the inside after only 1500kms

[@larrikinlancer685]

@@TheGingybeardMan I'll look into the Pod Filter. Thanks mate.

[@forgiven21801]

Hey man! They sent me 2 catch cans. I wonder if they saw your video talking about your rust issue? Anyway thanks for the tip - at least I wont be bummed until my second rusts. Lol

[@TheGingybeardMan]

Yeah I wonder if they did, ive got to stop being lazy and shoot them an email about it.

[@forgiven21801]

@@TheGingybeardMan They seem to be pretty cool fellas. Couldn't hurt.

[@neslesman6708]

Great ideas.

[@americanland878]

Where did you get the spacer? Or did you make one and paint it? Thanks

[@TheGingybeardMan]

I just made one and painted it mate.

[@paulsmale5436]

Think you should consider o2 sensor removal next, look deep into the subject and eventually you will learn those O2 sensors are not there to adjust the mixture for optimal running. They are there to weaken the mixture for emissions, potentially forcing your motor too run hotter. Good for emissions not good for your bike!

[@RJDW100]

Did you have to flash your ECM after installing the EBS?

[@TheGingybeardMan]

No sir. That amount of hot oily air coming from the breather bolts and into the intake was that miniscule that it doesn't affect the air fuel ratio however over time that oily mist will cause carbon build up on top of the pistons as its going into the combustion chamber.

[@TheGingybeardMan]

IF YOU DONT BELIEVE THIS IS NECESSARY, DOC HARLEY HAS ALSO RELEASED A VIDEO AFTER I DID THIS MOD..... CHECK OUT THIS LINK: kzbin.info/www/bejne/gqC5poKrnaupetU

[@americanland878]

Yes. I read that further down in the comments. Thanks Also the dk catch can rusted on the inside?

[@TheGingybeardMan]

Yes mate, I wouldn't recommend buying it unless they've changed the design since I purchased it. I was pretty disappointed considering it cost me $90 Au. I went back to running a $10 pod filter underneath the frame.

[@brianmaclennan561]

Was there much oil on the pod filter?

[@TheGingybeardMan]

I'd only done 100 kilometers with the pod filter on the external breather so there wasn't much oil on the filter at all.

[@shannonchampney8675]

What pod filter did you use, exactly?

[@pktech1969]

What did you use for the sleeve? Plastic, steel or rubber? thanks and good job on the mod

[@TheGingybeardMan]

I used some small aluminium tube I had 👍 although I wouldn't recommend a catch can. This one rusted badly on the inside after only 1500kms also I believe the catch can would pressurise as it only has tiny vent holes at the top. This could in turn have a negative effect on the head breather bolts. I'd recommend using a pod filter over a catch can 👍

[@h3r63rt]

Great video. Looks good.

[@TheGingybeardMan]

Cheers mate

[@RJDW100]

Do you get any blowback from your catch can set up?

[@TheGingybeardMan]

No I didn't get any blowback. But the catch can rusted badly on the inside after only 1000kms. I ended up going back to the pod filter which won't rust and will also breath alot better

[@lencampey5685]

Looking good mate

[@TheGingybeardMan]

Cheers mate 🍻

[@nickwoodruff7124]

where did you get that oil catch can bracket ?

[@TheGingybeardMan]

@@nickwoodruff7124 just a cheap chinese brake reservior off ebay mate had the bracket included

[@_leo3306]

Does your Pod Filter spills oil around? Does it have enough space internally to hold all those bad stuff given there is no oil separator inline?

[@TheGingybeardMan]

No the oil that's vented is pretty minimal and the filter element absorbs it really well.

[@_leo3306]

@@TheGingybeardMan do you suggest to install it vertically or horisontally?

[@TheGingybeardMan]

@@_leo3306 it really shouldn't matter, as long as it's secure

[@user-vq4vx4xc6d]

Have you had any issues since installing this? Also did you need a new tune? I have a 2020 Street Bob, DK customs kit is on the way, I already have my stage one kit on the bike, just wondering if I may need to get a retune at my local dealer

[@TheGingybeardMan]

I havnt had my bike retuned yet but will need to as I've put on a new air filter which allows the intake to breath better. I havnt had any issues since installing 👍

[@cmcdonough55]

I bought the SE Tuner and downloaded SE Software onto my laptop. Can now do a tune at anytime with no hassles or expense.

[@rockkawaski8155]

Hi man, what size is the bolts you’re using to tighten the catch can bracket? Thanks man

[@TheGingybeardMan]

Pretty sure it was a 6mm bolt and 40mm in length. The bolt came with the reservoir bracket I purchased, all I had to do was make a small sleeve so the bracket didn't bend when I tightened the bolt. A link to the bracket is in the description 👍

[@rockkawaski8155]

@@TheGingybeardMan thanks a lots man

[@harleyko]

what size is used horse ? id and od?

[@nathankeele3072]

Nice and tidy good job looks great 🤙🤙🇳🇿🇳🇿

[@TheGingybeardMan]

Thanks Nath, I think it came out pretty well in the end 👍 I may later change the hose for a stainless steel braided one in the future 🤔

[@antoinecaquard7391]

hello man! I allow myself to ask you for advice, sorry for my English, I'm French! In a previous video you remove the fork gaiters and I see that on your last videos you have new ones. Did you have any problems after removing them? I still hesitate to do it for aesthetics, I find it much more beautiful without ... thanks !!

[@TheGingybeardMan]

Yes I noticed I was getting some scratches from road debris. There was no major issues and you can keep them off as the softail standard has the same forks as the street bob and they don't have the fork gaiters on.

[@mrcappetto]

Antoine Caquard - Votre anglais (ecrit) est tres bien. Salutations des etats-unis.

[@jeffstange9183]

How are you liking those handle bars? I recently got my bike back out of winter storage and had 1st stage done, VH big shots and tuner, and had a sissy bar and handle bars installed from a company here(Dean Speed Custom) and the handle bars are similar to yours, both our bikes came with the 10.5 inch mini apes, these bars are 12 inch high and I absolutely love them, not just the way it feels when riding, but the look is killer!

[@TheGingybeardMan]

Man I love the bars im running on the bike. By far my favourite set I've had on the bike. Ill be putting a wrap around front fender and 21 inch front wheel on the bike next

[@jeffstange9183]

@@TheGingybeardMan cool bro, I'm sure there will be a video on that?? with your rear fender, and the new front, and the gas tank, can't tell it is a street bob. Wondering if you have thought about dropping the rear suspension and front

[@dkelli6020]

Love that headlight trim. Is it a whole new bucket and trim or just the trim with stock bucket?

[@TheGingybeardMan]

Yes mate it's just an aftermarket bezel. Here's a link where I bought if off eBay. I had to trim 3 mm off where it joins at the bottom so I could tighten it down snug. www.ebay.com.au/itm/274405774165

[@DoRC]

Why not just leave the stock lid seal in the brake reservoir? that's already there and designed to do that job and would probably work much better than Teflon tape.

[@TheGingybeardMan]

You're dead right mate good point. I just wasn't sure how well the rubber will hold up with the heat and oil. Despite have a rubber hose at the top of the catch can, I plan on swapping that for a stainless steel braided line.

[@jimzacame3922]

Question is, how far have you ridden the bike since the external breather mod and gas it worked as you planned? Thanks. JZ

[@TheGingybeardMan]

I've done 2500kms with the external breather. After 1000kms the internals of the DK customs catch can started to rust. I have since removed the catch can and now run the pod filter. I Havnt experienced any issues.

[@jimzacame3922]

@@TheGingybeardMan excellent! Thanks for the speedy response! I'm in the process of doing this mod to my '19 CVO Ultra 117ci. Your video was very helpful! Cheers!🍺😁👍

[@paulson9616]

Do you see any performance gain such as better crispy throttle response? What was a reason for change from catch can to filter?

[@yorichunt]

I’ve been enjoying your bikes evolution from over here in Perth, you’ve inspired me for a couple of mods on my ‘19 breakout. I think this one would be a good addition, though for my bike I think I’d locate it closer to where you had it zip tied. Did you order the catch can from over here, or ship it from the states? Did you buy it as a full kit or just the can by itself?

[@TheGingybeardMan]

I just bought the catch can it's self from the states. In the description of the previous vid I've listed all the parts required for the install?

[@yorichunt]

@@TheGingybeardMan Ah, cheers. I hadn’t read the description :)

[@yorichunt]

@@TheGingybeardMan I ordered the catch can, and went to Repco to start obtaining the other bits. The guy over here said they didn’t do vacuum hose that small, and they didn’t sell the T connector either. Did you buy them elsewhere? I bought 3/8x5/8 wiring grommets for the holes. We’re they the ones you used?

[@TheGingybeardMan]

@@yorichunt by memory I believe they are the correct grommet sizes. I bought the vacumm hose from the online supercheap auto website and the hose barb from China on eBay, here's a link www.ebay.com/itm/322716207234

[@yorichunt]

@@TheGingybeardMan awesome, thanks mate!

[@lawsonwilson8590]

Can you re-post the information for the brake reservoir that you got on eBay for the system

[@TheGingybeardMan]

Have a look in the vid description man, I've attached a link to it 👍

[@michaelofiara9732]

Exactly which kit is that since I have a ventilator air cleaner on my M8. great video

[@TheGingybeardMan]

I replied to your other comment in the previous vid re the parts required for this mod 👍

[@DoucetteMichael]

What was the size of hose you used for this system?

[@TheGingybeardMan]

I've listed everything I used in the description on my other vid 👍. The hose which leads to the catch can is 3/8 inner diameter.

[@tonyl8314]

How often do you have to dump the catch can?

[@TheGingybeardMan]

at this stage it's hard to gauge as I havnt put alot of kms on he bike since installing it. I'll check it everytime my air cleaner needs cleaning so probably every 4000 kms. I probably clean my air cleaner a little too often but I prefer my bike to breath well.

[@mikeessary4925]

S bob is looking so dam good bro! Weird ? Do you ever see any of the poisonous snakes or spiders in your area?

[@TheGingybeardMan]

Sure do mate, there's plenty of eastern brown snakes out this way. They're one of the most venomous snakes in the world. I've had loads of close calls with them over the years.

[@jeffreyuyanik1182]

How often does that catch can fill up?

[@TheGingybeardMan]

I only had it on the bike for 1500kms. In that time 1/4 of it filled up with an oily condensation. The thread inside the catch can which holds the filter element started to rust and deteriorate badly. I Would not recommend a catch can as it can also pressurise as the breather holes are extremely small. Definantly go with a pod filter over the catch can 👍

[@kevinhale628]

No torque specs for that cam bolt?

[@TheGingybeardMan]

I'm sure there are specs somewhere.

[@rider14mcd63]

Good job.

[@bking9226]

Nice Bike !!!!

[@TheGingybeardMan]

Thank you sir

[@DEJLRE]

A modern Harley shouldn’t even have an issue of this nature.

[@TheGingybeardMan]

Correct, I agree $100

[@bobgibb2781]

It's not Harley's doing . It's the strict environmental laws in the US . Many other bikes do this but most don't squirt the hot oil vapour so directly down the bike's throat . My ER5 ( Twister ) vents into the airbox on the OUTSIDE of the filter so that the oil condenses and and dribbles down into a transparent catch can .

[@thunder6646]

i am curious, whats the purpose of this hardware? this is a first for me seeing something like this and its pretty cool.

[@TheGingybeardMan]

Check out my previous video explaining what an external breather mod is 👍

[@joec2174]

Better heat proof that hose. You can use crt aluminum tape

[@tomhanley9575]

Id also be concerned about the close proximity of the nylock nut to the rear cylinder exhaust.

[@grimeyhonkyracing3938]

Is this why my fuel injector throttle body is all black and mucked up?

[@TheGingybeardMan]

Yes, the oil breather lines vent oil directly into the intake and when small dust particles mix with that it'll leave a sludge on the throttle body.

[@Tom-jw1pe]

Did you dye your filter black?

[@TheGingybeardMan]

I used a black filter oil. I did a video on it on my channel

[@Tom-jw1pe]

@@TheGingybeardMan ok Cool… I’m still looking for that video

[@TheGingybeardMan]

@@Tom-jw1pe sorry mate here's a link kzbin.info/www/bejne/aGS7hJJrm8SnldE

[@alaingroenen8505]

Why did You change filter To the catch can? Didn’t You Just install the filter?

[@TheGingybeardMan]

The filter was always going to be temporary until I could get the bracket to mount my catch can as stated in my last vid. I'd prefer to catch the blow by oil in a can than drop it onto the road when the filter fills up.

[@alaingroenen8505]

The Gingybeard Man ok, thx for the response! Keep up the Great video’s, You gave me a lot of inspiration!

[@TheGingybeardMan]

@@alaingroenen8505 not a worry mate, thanks for following the vids 👍

[@Simosay78]

hey mate would you need to get another dyno done after mod

[@TheGingybeardMan]

No sir, this is only a breather mod which doesn't affect HP. Essentially just diverting oil from your intake into a catch can. I wouldn't recommend a catch can though. If use a pod filter as it will breath easier.

[@allan9584able]

how did it go with the heat of the exhaust?

[@TheGingybeardMan]

No issues at all so far👍 over time I'd say heat will affect the hose but I'll end up changing it for a stainless steel braided hose.

[@allan9584able]

@@TheGingybeardMan yep nice work man , i will do the same type of thing when i get home

[@haroldbible44840]

Did he say where he got that kinda clamp setup at?

[@TheGingybeardMan]

There's an ebay link to the reservoir and bracket in the descriprion of this video 👍

[@haroldbible44840]

@@TheGingybeardMan I'm new on here. Where is the link i need to click on to get to the ebay link for the kit.

[@TheGingybeardMan]

@@haroldbible44840 on the right hand side of the video title there will be a small dropdown arrow, click on it and it will bring up the description of the video. I have a link to the item on ebay in the description

[@JerryMinakowski]

How much oil are we talking about?

[@TheGingybeardMan]

I've never measured it over time, but a mist enough to cause excessive carbon to build up.

[@piratelz4164]

So just how much oil are we talking about here?

[@TheGingybeardMan]

Didnt get the chance to measure it. You can see the affects with the before and after pics of other engines

[@petervanderhorst3491]

Looks great, all good mate?

[@TheGingybeardMan]

Thanks mate, all is well 👍

[@paulhorvath9784]

Any recent follow on videos?

[@TheGingybeardMan]

No sir I sold this bike 2 years ago. One thing I will say is don't buy a DK customs catch can. It started to rust badly on the inside after only 1200kms

[@dominiccoscarelli305]

I wonder if you could route the lines to the oil cooler instead of having to mount a container to collect that oil. Seems to me that would be better.

[@geraldfitzgibbon7428]

Why do u have to put on a catch can ?

[@TheGingybeardMan]

To catch the oil coming out of the heads. You could have it running to a pod filter but I dnt like the fact that if the filter overfills, oil will then drop onto the road.

[@mike2696]

😎😎😎

[@RealSuperRando]

Nice mate. How about some nice black spring clamps instead of those ugly hose clamps. Nice job though. Thanks for posting.

[@TheGingybeardMan]

Man ive since dit he'd the catch can and have gone back to the pod filter. The catch can was rusting from inside pretty badly

[@RealSuperRando]

@@TheGingybeardMan Well that certainly sucks. I thought it was billet aluminum. It should be for what they get for it. Did you locate your pod in the same place up front as before?

[@TheGingybeardMan]

@@RealSuperRando yes I've mounted the pod filter back under the frame. The catch can itself is billet aluminium but inside the internals house steel bolt which holds the 3 filter elements together and that bolt has rusted out really quickly.

[@jampyzerozero6921]

Nice clean install, I think I'll put this mod on my list of "things to do" and, is it just me or are your shorts getting shorter for every video? :P

[@TheGingybeardMan]

Thanks mate 👍 🤣🤣🤣 the hotter the weather gets the shorter the shorts get. Wait till it hits 40 degrees Celsius

[@jampyzerozero6921]

@@TheGingybeardMan I'm just jealous with winter rolling in for Canada..

[@TheGingybeardMan]

@@jampyzerozero6921 polar opposite here mate, Summer is just beginning. Isnt Canada one of the coldest climates on the planet? Tough riding weather mate.

[@jampyzerozero6921]

@@TheGingybeardMan We have extremes, Summer is typically 30C+ and Winters can be down to -20C at times.

[@jeffhudson1744]

just cut the diagram in the brake canister and then put foam in.

[@damienfrigo4734]

mine has water only no oil at all

[@TheGingybeardMan]

The water would be condensation build up from heat being put into the catch can. My catch can thread started rusting on the inside so I ditched it and went back to a pod filter

[@jivi77]

My opinion, you should have simply removed the hose and let the cylinder heads breathe directly into the air filter

[@TheGingybeardMan]

That doesn't really fix the issue. You will still have a hot oily mist going through your intake.

[@paulrevere4326]

Need to mount it out of sight. Too nice of a bike to junk it up with that ugly hose. I’ve never heard anyone ask another rider, where’s your catch can?

[@victorgonza4528]

There must be a better way , then a catch can

[@TheGingybeardMan]

There's 4 ways to divert the oil from the heads. 1- feed oil back into the intake (the factory harley way) 2 - allow oil to drop onto the ground (not a great idea) 3 - run oil to a filter (which will require cleaning as when its full the oil will also drop onto the ground) 4 - or the most sensible way In my opinion is to catch the oil in a catch can.

[@victorgonza4528]

@@TheGingybeardMan / How about running it back to the crank case .

[@TheGingybeardMan]

@@victorgonza4528 that would require drilling and tapping the crankcase to allow a return line. Something I don't want to do.

[@JSpool1]

Where did you get the brackets 🥲 I need this for my setup

[@TheGingybeardMan]

Mate all the info is in the video.

[@JSpool1]

@@TheGingybeardMan yeah just noticed it. I went through video kinda fast and missed it thanks. I thought the bracket came with hour kit since mine didn’t 😂

[@Heavy69Metal]

What about the vaccine loss on the heavy breather mod?

[@jonsixxx6569]

Over priced

[@TheGingybeardMan]

I agree mate, It was actually a rubbish product. the thread inside the cap started to corrode after only 1000kms.