Unleash the Power of Your Puch Moped: Secrets to Ignition Timing Revealed! Points Puch e50

[@CH00SEDEATH]

This has been the absolute best video on timing I've ever seen. Thanks for making this! Great production and lighting!

[@Corn-ped]

Thank you! I am trying to make the videos enjoyable with high production value

[@troyduncan1969]

@@Corn-ped You accomplished both! I know where to connect the timing light leads on a car. Would I simply connect the timing light to an external power source and then clip the inducer to the spark plug wire?

[@Corn-ped]

@@troyduncan1969 Just like a car. Connect the timing light to an external power source like a car battery or any 12v battery and then clip the inducer to the spark plug wire.

[@TAKETopicS]

does this go for any 2 stroke?@@Corn-ped like a pw80? i need to get the best pw80 ignition timing

[@tekboyg]

Best Timing Video! Love my Puch MS50!

[@Corn-ped]

Awesome! Thanks for watching!

[@rasmus1600]

Good and easy video! Currently rebuilding my E50, keeping the stock look and 49cc cylinder, but upgrading the original parts, to make it a 'sleeper' build. Boring up the 15mm carb, opening the airfilter box, new 49cc cylinder with 6 flushing channels, planed high compression top etc. Forgot the meassurements for the ignition, because it's 5 years since i opened the engine. Although you mention that the flywheels circumference is 360mm, which is most of the time correct. Puch originally came with Bosch flywheels that was 360mm in circumference. But in later production they changed from Bosch to another company, that had another circumference. It's always a good idea to wrap a string around the flywheel and meassure the length to be certain or meassure diameter and times that with pi(3,1415).

[@Corn-ped]

I have never come across a non bosch flywheel. but Ill keep my eye out! Good looking out. Where are you located?

[@TheSifting80]

Great video;) thanks

[@Corn-ped]

Thanks for watching!

[@dimopac6579]

Very Nice video. 10/10

[@Corn-ped]

Thank you!

[@amigo-e6o]

Fantastic, even the music.

[@puchymueller7209]

Where do you get one of those tape measures for the centimeters did you make and how what a great video

[@Corn-ped]

I made the tape measure. I just print it off and tape it on. www.mopedarmy.com/wiki/File:Puch_timing_sheet_5in_wheel.pdf

[@nlapp100]

Do you only work on Puch? Need a tutorial of how to set timing on an a35 tomos moped. Great video!

[@Corn-ped]

I work on everything. But I don't have a tomos right now. But the totmo sis the same as a puch. Just spins the other way.

[@nlapp100]

Thanks man!

[@Mike-wx7bx]

Superb

[@raghunath97]

excellent video. can we adjust timings by trial and error method?

[@Corn-ped]

yeah you can. Just mess with it until it runs good. Make sure you don't advance too far and over heat.

[@raghunath97]

@@Corn-ped Thank you.done succesfully

[@noahroper5614]

Again, another great and easy to follow video

[@Corn-ped]

Thank you!

[@jasonhorton393]

Killed it man, made it simple, is this the same for a peugeot

[@Corn-ped]

Thank you. I think a pug is more like timing without a woofruff key. Search how to time an hpi ignition

[@Khapaleno]

Awesome video! I do have one questions. How do i prevent my coils from hitting the flywheel? Whenever i turn my flywheel by hand i can feel and hear the scraping.....

[@Corn-ped]

ohh you need to set the air gap. There is detailed instructions in the manual with gap spec. But the way I do it is pretty easy. Take off the flywheel and put 2 layers of masking tape around the coils. Loosen the 2 screws holding each coil down. put the flywheel back on and the tape should push the coils in for enough clearance. Then with the flywheel still on rotate it around and tighten the coil screws. Then take off the flywheel and remove the tape. Then you should be able to put the flywheel back on with clearance.

[@Corn-ped]

tinyurl.com/245onyzf Here is the puch manual and at the top of page 109 it says set the gap to .016" - .024" and has a nice illustration.

[@Khapaleno]

@@Corn-ped Thanks! I will try to fix it this weekend :)

[@Corn-ped]

kzbin.info/www/bejne/eYq8qmirbLaefZo Just made a video about it!

[@rootstowingsyogahealingnew2101]

Are the points fully open at your timing or just beginning to open? An e50 I am working on seems like it’s over 20 degrees by timing light but the points actually start to move open at 17

[@Corn-ped]

they start to open a little early but dont spart until they are a little wider

[@frankdavidson9675]

it fires the second the points open the dweell time is how long they stay open what happens is this as the points open a ground is lifted from primary coil and condenser leads the voltage flows thru primary coil to the condenser thru it to ground (the little can is gd as this voltage flows in the primary it greates a magnitic effect in the coil and due to turns ratio in the secondary coil a very high voltage is flowing in the coil to the plug wire and plug as a spark all this happens very fast ( this is called a series resonant circuit) remember all the points do is lift the gd off ..if every thing is working right there is no voltage in the points but if cond is wrong type or defective a voltage will jump the gapof the points to gnd pitting the points if this happen replace the condenser and clean the points

[@lunamoto6495]

Killing it !

[@Corn-ped]

Thank you!

[@brianreiff8101]

I’ve got a Murray, I believe e50 platform as well, it has the same Bosch points ignition. Do you these bikes have a rpm limited by spark or are just limited by cylinder flow efficiency? Trying to increase the top speed a bit.

[@Corn-ped]

Limit by cylinder. Porting helps out you can get an aftermarket top end.

[@brianreiff8101]

@@Corn-ped awesome thanks for the info

[@alexneal8054]

Definitely going to be helpful when I go to rebuild my e50

[@Graciousdude]

Great video! I think my E50 is very weak at lower rpms. Can ignition timing help with that?

[@Corn-ped]

Yes. If you advance the timing it can have better low end. But it can cause hotter to end and detonation. Check with a timing light and see if it's set correctly first. And check your point gap.

[@toatski]

Would this timing be the same for a polini?

[@Corn-ped]

I like 1.8mm before TDC. Or 21 degrees

[@JoseGomes-o2w]

are you available for support. Quick phone call. I have a Tomos A3 and can not set the timing. The guy who had it replaced the stator from points to non points. It looks like a CDI. Ive tried everything. Cant find the spark marks on the stator or the cover.

[@Corn-ped]

Do you have a timing light?

[@zacharystoll1502]

Would this same procedure and measurements work on my za50?

[@Corn-ped]

yes you would just have to think about the rotation opposite since the engine rotates counter clock wise.

[@shortbus]

How can I tell if my 1978 Puch Maxi engine is an E50 or a ZA50?

[@Corn-ped]

the clutch cover is totally different. The ZA is wide and kind of an oval and sticks out a bunch. the E50 does not stick out as far and the cover is much smaller and circular.

[@charlesrknottsjr]

Is this process the same on a 1980 peugeot moped?

[@Corn-ped]

Yup basically

[@charlesrknottsjr]

Ok so on a za50 it would be 18 degrees btdc on the left side.

[@Corn-ped]

Yeah!

[@cricci03]

How tight do you tighten flywheel nut

[@VisarLimani]

Hi Thanks for your video.. I couldnt understand one thing, While you where rotating the ignition.. in the center of marks which u did, it should be 1.5 mm before the mark in the center or ? Thanks

[@Corn-ped]

Im confused by your wording. The flywheel should be 1.5-2mm before the tdc mark on the case.

[@rootstowingsyogahealingnew2101]

you rotate your flywheel with a drill with engine in off position? what is your power source for your timing light? this would be a bit easier than starting my car, lifting the hood and hooking up my snap on to my battery and taking my moped outside and starting it at nite

[@Corn-ped]

Oh haha yeah, I use a Milwaukee M12 battery. I have wanted to buy a battery powered timing light but I have a spare 12v battery. Using the car is a total pain.

[@frankdavidson9675]

you can use a batter y charger for batt scorce the spark causes the flash one lead you hook to the plug wire you turn dist slowly to adj timming then lock it down

[@Perry_Fan]

​​@@frankdavidson9675Are you saying you don't actually have to spend it like he did with a drill? But instead just turn it by hand and it'll show a flash on the timing tape? 🤔

[@nuherbleath461]

Is this on the E50 engine (48.8cc) ?

[@Corn-ped]

yes it is

[@BlackSublime]

Where did you get your pullers from?

[@Corn-ped]

I got them from Treatland.tv They have all of them!

[@BlackSublime]

@@Corn-ped thank you, I appreciate this. I’ve recently decided to try and fix up my moped but don’t know what I’m doing. I found one of your videos on Reddit and it’s a good reference for when I’m fixing it.

[@Corn-ped]

That's awesome! What are you working on?

[@BlackSublime]

@@Corn-ped a 1978 garelli gran sport. I got it a few years ago and it’s been sitting in my garage since, I decided to try and fix it a few days ago but so far all I’ve managed to do was take it apart and put it back together😂

[@rootstowingsyogahealingnew2101]

what if you put in a new crank and your flywheel slots come nowhere near to lining up to the opening? how do you set point gap then??

[@ryanurso]

I also would like to know.

[@rootstowingsyogahealingnew2101]

I ended up using a different flywheel so i could set the gap and then put the oem fluwheel back on. Had to do this with a 74 maxi

[@Corn-ped]

Is the flywheel stock? Is the stator plate stock ? The slots are there so you can adjust the points? It sounds like you might have a miss match set? I wish you could posts photos in the comments.

[@jenblack80]

What kind of timing light would you recommend? I've been looking at one that runs on 2 D batteries (self powered) because the whole hooking it up to the car thing seems like a pain in the ass, but would love to know your thoughts....

[@Corn-ped]

Yeah that self powered one looks great I was also looking at it. I have a Milwaukee m12 drill battery I use.

[@stevenwhitright]

nice one!

[@Corn-ped]

Thanks!

[@abcd-wg2iq]

Pefect

[@emeraldviking3637]

Is a puch ds50 engine similar to time

[@Corn-ped]

No. I believe the ds50 is a shifty motor. Not a moped.

[@slowedtoperfect3077]

How to wire for only spark pls help

[@poweredbytim4010]

What piston stopper are you using?

[@Corn-ped]

amzn.to/40Iefw1 I like this one. It has a nice soft top to it.

[@VintageGarageYT]

Good video! I've also tried to make a video on this on my RD50 build (still has to come out) but filming it was a real hassle. Seems like you've got your camera gear set up pretty good! What are you using?

[@Corn-ped]

I'm using a Canon Rp and a tripod. I still haven't figured out the right microphone. I have tried 3 and so far the cheapest mic has been the best.

[@Corn-ped]

I also have a couple lens but it's annoying to switch them while working with greasy stuff so a nice zoom lens works the best.

[@VintageGarageYT]

@@Corn-ped Thats a good tip. Currently still working with a gopro, but have been looking around to upgrade

[@Corn-ped]

@@VintageGarageYT I went with the Canon RP because I already had Canon lens and it has AUTO FOCUS and TRACKING. I do most of my filming alone so I needed autofocus and tracking.

[@VintageGarageYT]

@@Corn-ped Awesome thanks! Will look into it. Ps. Check out my channel if you want. I'm still figuring things out so tips are appreciated!

[@KelikakuCoutin]

Thanks for the content. Keep up the good work! בס'ד

[@dutchmilla2794]

How bout e50 clutch tuning vid next

[@Corn-ped]

Yeah! I gotta get an e50 running first! But j got a new claw clutch coming!

[@maliking02]

I did everithing as ypu and mine dont want to run proprerly

[@Corn-ped]

You have good spark and its properly timed? What is it running like? you may have a different issue.

[@maliking02]

@@Corn-ped new spark and when i put stator al the way to the right it hardly starts and turn of if I dont give throttle

[@maliking02]

Is stator of this bike rotating clockwise or ? mine rotates counterclockwise

[@Corn-ped]

This bike rotates clockwise. What kind of bike are you working on?

[@maliking02]

@@Corn-ped tomos apn 6

[@jimbrodhagen165]

Yeah, so I'm probably just being stupid... But I followed this tut and ended up firing at 0° (TDC) when stator is fully advanced. How am I being a dummy here?

[@Corn-ped]

Points? Are you using a woodruff key? You sure your mark is 0 TDC? Sounds like a measurement is off or the woodruff key slipped.

[@jimbrodhagen165]

@@Corn-ped points and woodruff key, yes, ended up remeasuring for TDC using a couple different methods. I'm timing with a light.

[@jimbrodhagen165]

@@Corn-ped just to be sure I got this right, I set the point gap at TDC to .4mm. Then, I find 18° BTDC, mark it on the flywheel, start and check timing with light. I ended up at 0° TDC, so I advanced the stator all the way (dremeled out to get more adjustment room even). Somehow I'm still firing at 0° and it did me a big confuse.

[@Corn-ped]

So you can move you stator and your timing doesn't change?

[@Corn-ped]

Are you marking 0 on the case and flywheel. And then 18 on the case? And the flywheel 0 should fire at the 18 on the case