Dodge Avenger /Chrysler Sebring Ignition WCM Skreem module 2007 2008 2009 2010 2011 2012 2013

Repair of the WIN module starts at $149.95 and comes with 12 Month Warranty. USPS Priority Mail would cost an additional $19.95 If you only have 1 Fobik remote, you can add an extra Fobik remote programmed for $100.00. When you receive your WCM / Skreem/ WIN just plug it back in and Drive.
To match a SKREEM/SKIM Immobilizer or ORDER click on the Link below:
www.autotechele...
*Some products will have a CORE CHARGE that is refunded when we receive your old part.
part 05026157AN 05026157AS 05026157AQ 05026157AI; 05026157AJ; 05026157AK 05026157AO; 05026157AP 05026157AG 05026157AM 05026157AL 05026157AH
P05026157AN P05026157AS 05026157AQ P05026157AI; P05026157AJ; P05026157AK P05026157AO; P05026157AP P05026157AG P05026157AM P05026157AL P05026157AH
5026157AN 5026157AS 5026157AQ 5026157AI; 5026157AJ; 5026157AK 5026157AO; 5026157AP 5026157AG 5026157AM 5026157AL 05026157AH 5026157AS 5026157AT 5026157AU 5026162AQ, 5026162AR, 5026162AS, 5026162AT 5026162AU, 5026185AF, 56053016AN, 56053016AO, 56053016AP, 56053016AQ, 56053016AR, 56053016AS, 5026185AB, 5026185AC, 5026185AE, 56053016AM
Please ship WIN module and any Fobik(s) to:
Auto Tech Electronic
Walton Guerrero
102 S Malinche Ave
Laredo, Texas 78043
Office 956-508-3450 or Text/SMS: 210-920-5819 Email: [e-mail]
Paypal is [e-mail] or click paypal.me/autotechelectronics
We stock All WIN modules with transmitter Kits. Ready to ship programmed vehicle and VIN specific.
Manufacturer: Mopar
Part Number: 5026162AO
Part: Keyless Entry Receiver with Remote Start Without tire pressure monitor.
Replaces: 5026162AI, 5026162AJ, 5026162AK, 5026162AL, 5026162AM, 5026162AN 5026162AQ, 5026162AR, 5026162AS, 5026162AT
Manufacturer: Mopar
Part Number: 5026157AU
Part: Keyless Entry Receiver Sebring, Avenger. 200, Avenger. Sedan. Convertible. Without remote start. With time delay headlamps. Without tire pressure monitor.
Replaces: 5026157AG, 5026157AH, 5026157AI, 5026157AJ, 5026157AK, 5026157AL, 5026157AM, 5026157AN, 5026157AO, 5026157AP, 5026157AQ, 5026157AR, 5026157AS, 5026157AT
www.autotechele...
www.autotechele...

[@sixwins03]

Thanks Walton Guerrero, for the great work on my 09 Town & Country. for those skeptics out there, my Chrysler showed damaged key a few months back and then 2 weeks ago my 2nd key failed they same way. I did some research and found that my wireless ignition module (WIN) was the most likely cause. I found Walton Guerrero's videos and was skeptical myself, but decided to risk it because of all the positive reviews. I contacted Walton about my problem he quoted me $249.95 to fix my WIN Module and add another key. I shipped off my WIN and my last remaining "damaged" key on a Thursday and had it back on Wednesday (shipped via USPS 2 day Priority) So what i'm trying to say is you can trust Walton! Thanks a million Walton.

[@866mary2]

I would never remember how to put it back together! Great video btw!

[@randy7361]

thank you for posting this video that cylinder is in the way of the cable I need to disconnect to install a harness for a remote start ..........I would of ended up sending back the remote start till I found this video!!!!!!!!!!!!!!!!!!!

[@randy7361]

wow even after removing the screws the cylinder is still locked in place

[@user-lh4ww5xs3x]

Thanks for the vid. Which one is the shifter cable?

[@tylercore9554]

So if I needed to replace the skreem in my 2010 Dodge Avenger how would I go abt reprogramming it to my current key? I put in a remote start and then after that my car will crank but immediately die with the security light flashing, even without the remote start hooked up.

[@AutoTechElectronic]

I would make sure the remote start is installed correctly and that the skreem module is not damaged.

[@tylercore9554]

@@AutoTechElectronic okay thanks, what signs could I look for for screem damage?

[@darlatube]

Walton - this is a great video on how to get that ignition module out, however, the problem we are having is where is the active retainer to remove the key cylinder. Can you help with a picture?

[@klaytonkixmiller4095]

Um.... the piece of plastic around the ignition chamber does not come off with the dash. It appears to be connected all the way to the other side of the steering column with the piece of plastic around the trunk release

[@richrichardson8811]

FYI it is completely different for a 2008 dodge advenger to remove the front panel and steering column. I had to remove much,much more than the video showed. It was a very helpful video but it would have even more helpful to see how you released the electrical wires from the ignition rather than the directions at the end. Thanks for the video.

[@bryanrichardson4811]

How did you remove the front panel on your dodge avenger, because I cant seem to find how to do it?

[@cyprianoldakowski3518]

I’ve got a 2005 Jeep Grand Cherokee. I bought a used WCM from the junkyard. I have a scan tool that I can use to program this module to my car. I’ve gotten the skim pin from the dealer for my car but that pin is not working when I’m trying to program this new to me wcm. Do I need to the skim pin for the vin that this wcm came from in the junkyard ?

[@monicacasanova7340]

Buenas tardes quería saber Qué antena inmovilizadora le puedo poner a mi Avengers 2013 De qué año le queda es 4 cilindros

[@AutoTechElectronic]

Encie El VIN a 830-374-6845 para Con segguir El numero de parte

[@marievaldez4009]

I have a question what is a Electrical wiring?

[@NickRcks1124]

Marie Chavez No this too big or smal

[@tiffaniewilburn6306]

Do you still replace these?

[@johnprovost9805]

I can not find the interior fuse box in my 2013 dodge average can someone help

[@KillerJay101]

they have a tipm which is located under the hood by the air cleaner box

[@KillerJay101]

total integrated power module

[@elwero705]

What wer youre symtomps ? Crank but no start?

[@AutoTechElectronic]

El wero. This vehicle had crank but NO Start. Security Light was flashing when key left in RUN position.

[@Zolto1968Niebieski]

What am i doing, if I haven't key? How can I remove iginition without key? Chrysler Sebring 2008

[@AutoTechElectronic]

what happened to your key?

[@Zolto1968Niebieski]

All keys lost

[@AutoTechElectronic]

Why are trying to remove cylinder? In a lost key situation, just make the key first. If skreem is bad, replace it after.

[@Zolto1968Niebieski]

I need mechanical code number of key and i can remove ignition cylinder and read this code

[@AutoTechElectronic]

Zolto1968Niebieski there is no code on the cylinder. And is a lot of work and nearly imposible for a novice. The drivers door is much easier