Thanks to your video I went from an $800 repair to a total cost of about $53 - parts, diagnostic code readout, and bay/lift use - and about 20 minutes of my own labor!
@mystic66986 жыл бұрын
Just realized I'm on my sons acct but anyway THANK YOU SOO MUCH!! I had my truck read & it's the right speed sensor & didn't know if this was something I could do myself until now! The mechanic showed me 2 different sensors but they didn't look like the one you showed so now I know what to get. Seriously can't wait for the lights to go off & have my cruise control back! Thanks again! Now I just gotta figure out why my airbag light keeps going on & off
@MotorCityMechanic6 жыл бұрын
Thanks for commenting and for watching. Glad that the video was helpful. Make sure to subscribe,
@mandogomez40543 жыл бұрын
Awesome buddy. I was clueless to to where the wires or harness needed to be. I just knew that without these wires my vehicle wouldn't run.
@stevetandy12162 жыл бұрын
Great video, very helpful, looks like something I could do, thanks from the uk 🇬🇧
@antoinettearchibeque82306 жыл бұрын
Hello thanks for you help! It was a vacumme leak. Your good! I will give a hundred thumbs up!
@MotorCityMechanic6 жыл бұрын
Awesome....glad it was something simple. Thanks for the update and the 100 thumbs up! lol.
@whatshisname5105 жыл бұрын
Thanks for the video. I had to remove the rotor to access the other side of the sensor when it broke in the hole.
@MotorCityMechanic5 жыл бұрын
Your welcome Shane. Appreciate you watching and make sure to subscribe.
@cinderellashoe75113 жыл бұрын
Sigh. Ours broke as well. Some being tight haha yeah ours was wedged so bad then broke then the broke piece fell off ...somewhere.. any chance this isn't a whole new wheelbearing due to lost sensor in rear left or if it fell is there no way to access it without ruining the bearing and rotor?
@chuckmayoification Жыл бұрын
Thanks for a great video! I just replaced one of my rear speed sensors and your vid was very helpful!
@maximilianorodriguez48414 жыл бұрын
This is a great, easy to follow video. keep it up!
@MotorCityMechanic4 жыл бұрын
Thank you! The feedback is greatly appreciated. Make sure to subscribe
@warriorlink86122 жыл бұрын
Simple and to the point, thank you
@jimmcnally42568 жыл бұрын
Hey David I have a 2010 dodge ram 3.7 two wheel drive pick up just a work truck. I keep getting a U1418 code i have replaced the sensor checked for power cleaned the tone ring. the light will go off and then shortly come back on again UGH what I'am i missing I will be checking the other left side today but I,m shooting in the dark here. Love the video on the cabin filter helped me fix mine took the fear out of working on something new ( I have a 64 Valiant) Keep up the fantastic work cheers Jim in Canada
@jadedjeff3 жыл бұрын
helpful, just needed to see what it looked like under there, and this did the trick.
@JohnAllocca9 жыл бұрын
how about a video on a dodge nitro rt (07) tune up, plugs and wires, can't find one and it doesn't look simple, thanks for the speed sensor video, I actually have to do one on my wife's 07, just don't know which sensor it is, don't have access to a scanner
@JH-lk6lb2 жыл бұрын
My fiances 07 Nitro had the ABS, Traction Control and ESP BAS light come on today. She got 4 new tires a week and a half ago. I am digging into it tomorrow but what would your first assumption be? Mine was speed sensors but I'm not sure. I don't have high end scanners so I'm going to replace all 4 sensors and cross my fingers. So if I replace those and it doesn't fix it what would your next verdict be? Love the video man! Subscribing now!
@bwt32788 жыл бұрын
much thanks, im a decent mechanic, but I figure having an idea of how things are set up won't hurt when crawling under. pretty much a generic set up, but I've never seen a sensor of that style before. I've got ABS, ESP, and traction lights on right now, so I'm going for speed/abs sensors, then on to the brake switch if that doesn't fix it. Ive only got a $250 scanner so I'm planning on using my power probe or multi meter on another sensor for a bench mark and comparing from there. anyways thanks for the video. you're doing great, if you read this and have any imput, I'd app the insight.
@MotorCityMechanic7 жыл бұрын
The most common cause is the speed sensor. You just need to narrow down which one.....checking the codes would be the best method for that. Then you can just replace only the needed sensor.
@kelvinmckelvy82075 ай бұрын
😂😅 I love your work you've been grateful to me
@joniluvschachi12 жыл бұрын
omgosh thank you so much can't wait to fix it...
@MotorCityMechanic2 жыл бұрын
Thanks for watching and for the comment
@coreyadams46463 жыл бұрын
Great video buddy!
@MotorCityMechanic3 жыл бұрын
Thanks for the comment. Dont forget to subscribe
@raymondbigger56992 жыл бұрын
Thank you.
@kenbell78744 жыл бұрын
Had this problem until I applied the parking brake and released. Has not come back since. About 6 moths now or little longer.
@philipmcdonough76833 жыл бұрын
Excellent video, very helpful thank you so much.
@belindalara14604 жыл бұрын
Do you have any videos on how to reset a key fob for a 2010 nitro? I've changed the battery but that isn't it. The alarm and locks go off on their own.
@CC-qw5ps3 жыл бұрын
hello great video. i have a low esp problem on my dodge nitro the light comes on and goes out from time to time i replaced the two rear sensors the problem persists. with which software do you scan the dodge nitro please? thanks in advance
@derrickdukes21913 жыл бұрын
Thank You My Brother...Bless Ur Dayyy🦍
@MotorCityMechanic3 жыл бұрын
Your welcome. Thanks for the comment
@georgeconetta7 жыл бұрын
Thanks for your advice 👍🏻
@MotorCityMechanic7 жыл бұрын
Your welcome sir. When you get time feel free to check out my other videos and make sure to subscribe!
@ssjmason6 жыл бұрын
My 08 charger has the code C102A and U1417 and I replaced the wheel speed sensor for left rear and the wheel hub itself. Whats next?
@jacobbrown8561Ай бұрын
2009 Dodge Nitro 3.7L SLT Will BAD Wheel Speed Sensor "disable" SpeedOmeter? Lights: ESP/BAS, Air Bag, ABS, Traction No Check Engine Lights.
@sheenab.69207 жыл бұрын
if the traction light goes on and off and stays on pings and then the car slows down then accelerates while you are driving, what do you think is the issue. Would the sensor force the car to slow down then speed up? Dodge Nitro Detonator 2010 42000 miles
@MotorCityMechanic7 жыл бұрын
The symptoms can be different sometimes. First step will be getting those codes checked. Then we have a path to go down as far as checking things out. Thanks for the question and for watching
@cecyvillarreal16706 жыл бұрын
Would bad abs sensors be the cause of speedometer not functioning?
@MotorCityMechanic6 жыл бұрын
It can. I would check for codes first using a high end scanner that can access all the control modules to see is any thing shows up, that would give a direction to go in and then also monitoring the speed data would helps as well.
@813Tactical Жыл бұрын
Ok. Do all 4 of my sensors make the 4wd work. Because when I go into 4wd it still doesn’t kick on. But the 4wd light on the dash comes on. But doesn’t want to actuate
@antoinettearchibeque82306 жыл бұрын
Could you tell me what to look for when the code is saying. Idle is higher than expected. 2008 dodge nitro 3.7
@MotorCityMechanic6 жыл бұрын
First thing is to make sure there are no vacuum leaks anywhere....the other is to check the TPS operation. Here is a related video on the 4.7 which has the same set up as the 3.7......it might help. Thanks for watching and make sure to subscribe. kzbin.info/www/bejne/pZTXYaiZnJZmnbc
@duanebonney8 ай бұрын
Hello. Why would I lose signal from both my rear speed sensors, when I change in to 3rd gear, and get stuck in that gear? Extremely frustrating.
@adamedds241822 күн бұрын
I am having the same problem. Did you figure yours out
@duanebonney21 күн бұрын
@@adamedds2418I changed the tone rings.
@chrissummer37856 жыл бұрын
My 4X4, ABS, EBS? Skid control, keeps coming on. I brought it in for a right rear sensor replacement a few times and it keeps costing me $. If I know where’s it’s at is it possible that I can do my own replacement or check on that part from time to time? Another thing I do not no where the sensor/ harness is located. I’ve seen mechanic crawl under a use tape as a temporary fix or I think it was to support the wires better from getting wet... what can I do? Is this part a major problem and should I get a different vehicle?
@theinfidelH86 жыл бұрын
If the red tab on the 2 stage lock is broken, how do you get that red piece to unlock?
@loverlove247 жыл бұрын
Hi there. I have a Dodge Nitro 2.8 CRD automatic transmission and its currently on Limp mode. The gears don't shift. Can a bad speed sensor be the cause of that? My ESP ABS lights are on by the way. A reply will be much appreciated. Thanks for the video.
@MotorCityMechanic7 жыл бұрын
loverlove24 First step....having all the codes checked. An ABS speed sensor issue can affect different things such as transmission. Getting the codes will point us in the right direction. Thanks for watching and make sure to subscribe
@travelanciro9 жыл бұрын
My dodge nitro always have light on esp bas. Is this same troble shooting?
@MotorCityMechanic9 жыл бұрын
Jerico Anciro The first step is to see what the codes are causing the warning lights to come on. If it is a speed sensor code then the procedure would be the same of the rear. The front replacement is different but simple enough.
@bigx90956 жыл бұрын
Is there a way to manually clear the codes?I replaced the sensor that the Dodge dealership said was bad and my lights are still on.
@ronnietimpson1128 жыл бұрын
my dodge nitro don't a light on but when i give it the gas i don't get up 40mph even with it to the floor. is the abs the same as the speed sensor, please help got to get it right so i can get work tomorrow.
@Martinboy854 жыл бұрын
Anything for rear wheel bearing install?
@MatthewVas134 жыл бұрын
How do you install parking sensors on a 2010 dodge nitro
@joserangel44257 жыл бұрын
does this problem have to do whit no going over 25mph? all the lights everyone mentioned came out in the dash bord and also when i shift it shifts hard...
@MotorCityMechanic7 жыл бұрын
It depends Jose. A bad speed sensor can affect a lot of different things. It will require starting with scanning for codes and then going from there. If you get a wheel speed sensor code then I recommend replacing being that its a common failure.
@bradrogers98999 жыл бұрын
is the front the same on the abs sensor as the rear on the nitro?
@jamescampbell92064 жыл бұрын
I can’t find my problem online my speedometer won’t work until my brake light turns on I have a video I can send if you tell me how I can’t figure this out
@BigGilbert218 жыл бұрын
thanks for video!!!!!!
@MotorCityMechanic8 жыл бұрын
Your welcome and thanks for watching. Make sure to subscribe!
@angelom46097 жыл бұрын
Thanks for the great vid. I hope this is what I need. I have 2009 nitro SE and abs , brake & esp lights all came on. Speedo stoped working for a day also. Is there only one of these sensors & where is it ? A Little history two week back I had to replace left rear caliper, the piston was not moving freely and burning up shoes.
@angelom46097 жыл бұрын
looks like the speedometer not working is intermittent. its working today. was not working yesterday.
@MotorCityMechanic7 жыл бұрын
There should be a sensor in each corner at each wheel. I recommend checking the codes to see if the issue can be narrowed further.
@angelom46097 жыл бұрын
The advice was great,but infortunetly this was not what I needed. I had a code C2200 & U0121 and was told i needed a ABS module. I know a replacement would need to be initialized some where, but I cannot find a vid on how to replace. Do you have one or can you create to show the step needed?
@italia3929 Жыл бұрын
Missing speed sensor causes the transmission to make a straining whine like noise at low speeds. Anyone else notice this?
@larsbambi15753 жыл бұрын
My damn sensor broke into two pieces. Having a hell of a time getting the other half out..rust belt Is there any way to get to the front? Right rear
@cinderellashoe75113 жыл бұрын
Did u have any luck? This just happened to us unfortunately as well. Tight pos sensors.
@larsbambi15753 жыл бұрын
@@cinderellashoe7511 yes ended up pulling it out through the back side
@billsadowski77739 жыл бұрын
looks good l have a 2008 jeep liberty , should be the same to change speed sensor.
@MotorCityMechanic9 жыл бұрын
+Bill Sadowski Thanks Bill....should be very similar. Make sure to subscribe and enjoy the weekend
@Timbob-z1c25 күн бұрын
U da man!
@kevinbrother43126 жыл бұрын
I have a 07 nitro driveshaft pulled wires out going to the fuel pump sending unit it's in limp mode please help
@MotorCityMechanic6 жыл бұрын
So did it pull out all the wires....couldnt because it wouldnt even run at this point....or just the fuel gauge wires? Depending on the way it pulled it out...you may have damaged terminals on the wires. If thats the case the the fuel pump connector pigtail may need to be purchased and then soldered in place of the old one.
@Empok_Nor5 жыл бұрын
Would you have a trouble shoot video for a Nitro's TPMS? And yes all tires have the same psi.
@MotorCityMechanic5 жыл бұрын
I will certainly keep it in mind as a future video. Thanks for asking and for watching. Make sure to subscribe
@omarg72599 жыл бұрын
Any videos on replacing a thermostat for a dodge nitro 3.7L?
@MotorCityMechanic9 жыл бұрын
Victor Gonzalez Sorry but I currently dont. I will try to keep an eye out if one comes in for that repair. Its a fairly simple job being that the t-stat is located at the bottom of the engine where the lower radiator hose goes to the engine. The t-stat housing is plastic and has two bolts. Thanks for the request
@hectorvazquez16173 жыл бұрын
Eso bas light on a dodge nitro with track light too how can I fix that??
@MotorCityMechanic3 жыл бұрын
First step is checking the codes to see what the issue is and then going from there.
@charliehodge51323 жыл бұрын
Following, same issue, I don't have a tool either how much does it usually cost to have them ran?
@ibiscar067 жыл бұрын
hi, my 08 nitro started to fluctuate speed while driving. would this be a fix, I have codes c1070, c2115, and c2101, which are brake pedal switch, dynamics sensor supply, and battery voltage. where would I start?
@MotorCityMechanic7 жыл бұрын
The voltage codes would be where I would start. Checking the charging system to make sure no higher then normal voltage is recommend. We also need to clear the codes and see how soon they return. From there the voltage at the ABS module needs to be checked to makes sure its not higher then normal as well. If all checks okay then the ABS module may be bad and need replacing.
@ibiscar067 жыл бұрын
MotorCity Mechanic thank you very much for your help, kind of odd that dealership had it for like a week and didn't find anything.
@MotorCityMechanic7 жыл бұрын
Sometimes things dont act up when we have the vehicle and checking it but then again sometimes its the person working on it.
@IAN1208627 жыл бұрын
Hi I have a 2.8. CRD 2009 Nitro, are the right and left rear wheel speed sensors the same or will I need to buy two ?
@MotorCityMechanic7 жыл бұрын
From what I am seeing.....they are the same. But before you go ordering it....make sure to have the place your getting them from verify that I cam correct. Thanks for the question. Make sure to subscribe and share the videos with others.
@prdz89268 жыл бұрын
hi, thanks for video, awesome job, hoping to get the wiring changed I think I need the connector as well any clue what's part #
@MotorCityMechanic8 жыл бұрын
Thanks. I need to year, make, model, and which sensor you need the connector for so that I can have my parts department look it up tomorrow
@prdz89268 жыл бұрын
2008 dodge nitro, 3.7L right front wheel
@prdz89268 жыл бұрын
Thanks bunches!!! I'd really appreciate the help 😊
@MotorCityMechanic8 жыл бұрын
+Patricia Rodriguez tell me thank you when I get you the part number lol. I have been know to forget so make sure to remind me incase you don't hear anything back later tomorrow
@prdz89268 жыл бұрын
+MotorCity Mechanic lol yes Sir, will do 😉👍
@RedCornOutdoors8 жыл бұрын
if I don't have a scanner, could I check it with an ohm meter?
@MotorCityMechanic8 жыл бұрын
The only way to really test one is with a lab scope. I don't remember about the ohm readings. In some cases you can check it simply that way while others you can not. One way to see if it's possible is to disconnect the other speed sensor on the opposite side and see if you get an ohm reading from it and if so.....compare that reading to the questionable sensor. Thanks for the question and make sure to subscribe
@leonardophotographystudios88477 жыл бұрын
jealous, just did a front one on my dodge journey and had to drill it out !
@MotorCityMechanic7 жыл бұрын
They can be a pain to get out from time to time. Thanks for watching and for the comment. Make sure to subsribe and have a great weekend
@michaelsarabia23258 жыл бұрын
do you have to clear the code after its replaced
@MotorCityMechanic8 жыл бұрын
+Michael Sarabia Its recommend to clear the code. Otherwise it may take some time for it to eventually cause the light to go off. If you okay with the light for a bit of time then feel free to wait until it goes off over time once it passes the test when checked. Thanks for watching and make sure to subscribe !
@GabrielLopez-od7id9 жыл бұрын
Do they just sell that part where it connects ? I don't need the whole part just the part that clips
@MotorCityMechanic9 жыл бұрын
+Gabriel Lopez Evening Gabriel......can you please clarify exactly what your describing? Are you speaking of the connector for the sensor?
@GabrielLopez-od7id9 жыл бұрын
+MotorCity Mechanic sorry yes the connecter the connector that goes on the wheel
@MotorCityMechanic9 жыл бұрын
Gabriel Lopez Yes sir they do.....I you get me your VIN number and let me know which wheel (incase they are different), I can have my parts department at work look up the connector part number and possible price. If you don't want to show your VIN here then you can email me at david@motorcitymechanic.com
@GabrielLopez-od7id9 жыл бұрын
+MotorCity Mechanic OK I will email you
@arthurleino8 жыл бұрын
I have a 2009 challenger with a code for right rear sensor. How do you pull the right and left connectors down where they go thru the car floor connection?
@MotorCityMechanic8 жыл бұрын
If you look closely you will see a metal clip that goes thru the side of both of them while they are sandwiched together. You just push in on the middle flat spot of the metal clip and then pull the two connectors out. Worse case scenerio you can remove that metal clips to get the connectors off and then reinstall it before pulling the connectors back in. Thanks for the question and for watching. Make sure to subscribe
@arthurleino8 жыл бұрын
+MotorCity Mechanic Thank you!
@MotorCityMechanic8 жыл бұрын
Your welcome. Hopefully once you look at it again it will make sense now. Its hard to explain some things in just words.
@arthurleino8 жыл бұрын
+MotorCity Mechanic Subscribed!
@MotorCityMechanic8 жыл бұрын
Thank you sir
@oliverleyva83986 жыл бұрын
on which side is the sensor en Dodge Nitro
@MotorCityMechanic6 жыл бұрын
The Dodge Nitro has 4 ABS speed sensors.....one at each wheel.
@ChrisLaw843 ай бұрын
Half My red piece snapped off. Used to love my dodge now i just think it’s a piece of shit