Dodge ram 1500 quad cab rear door stuck

I run through the most common causes of the rear suicide doors getting stuck and how to fix them on a dodge ram 1500 ext cab. Should work for years 1998-2001

[@bryantaber6078]

So far this is the best video Ive found to fix these doors. Clearest and Easiest to understand.. Nice Job!!

[@Fearborne]

Handy-Mann comes in clutch again! I did fix that heater core and I do have heat now. Going through all the issues and your videos are a huge help.

[@Handy-Mann]

I'm glad I could help!!!

[@rhythmless1]

Many thanks for your video! I went to Harbor Freight and bought a panel clip puller just to make me feel better about doing it, but this video was a great help. I finally don’t have to go to the passenger side every time anymore!

[@twinnedmaster3453]

Great video man. I was just to timid on taking the panel off myself. But after seeing your video its far more easier than expected. Thank you.

[@galloamaya]

these best video on this subject. Clear and concise, Thank You !

[@Handy-Mann]

Thank you! I'm glad I could help!

[@sks6689]

Best video ever for Dodge 1500 rear door. thank you . I am gonna fix mine soon .

[@Handy-Mann]

I'm glad you liked it!

[@dylanlikens6012]

You definitely need to make more videos this video is the best video of how to do I’ve seen yet on KZbin definitely following

[@stevevonrock2416]

Thats the vid i was hoping to find on my search , thank you sir

[@Handy-Mann]

Glad I was able to help!

[@joeteejoetee]

Great video and great tip about opening the side window !

[@waynehutchinson1423]

Great video.Thsnks .l start bought a 98 Dodge with with both quad doors stuck.Thanks .l subscribed and liked.

[@richpeil6251]

Awesome!! Exactly what I needed. Great video quality and information,..Thanks!!

[@rusty-ole-boomstick1268]

Thanks, hardest diy video to find. Kudos

[@Handy-Mann]

Glad I could help!

[@bearcat6278]

Great video. Exactly what I needed to see. Thanks

[@Birdsfly11]

Thanks! this was by far 100% helpful!

[@Handy-Mann]

Glad it helped!!

[@garybennett5207]

Nice video, thank u for the exclamation

[@bren730]

Thanks Easy to understand vid Good job Helped me a lot

[@Handy-Mann]

Thanks! I'm glad it was helpful!

[@richardbates2367]

Neat I have a black 2001 dodge ram quad cab long bed 1500 4x4 Laramie slt that the Dr rear door sticks mine has the usual dark mist gray interior.

[@Handy-Mann]

Hopefully this helps then!

[@davidpearson5819]

Thank you for this video dude! This is going to be super helpful. I have the exact same truck and my back door just got stuck on the lower latch. Do you happen to know if you can just buy the cable alone? Or do you need to buy the entire handle/latch assembly? Thanks in advance.

[@greysonhoffman3647]

Really need a tutorial on how to fold the back seat up when the latches don't work

[@i.can.sew.anythingchic3295]

Awesome.. great information!!!

[@Handy-Mann]

Glad I could help!

[@garrythompson475]

t-25 = torx bit size 25, it is better to use a nail puller to loosen the plastic anchors. Harbor freight has a pack of 4 plastic pry bars.

[@D-train69]

Where is the cable held at mine is free and it won't stay connected it just pops off ???

[@DCM8828]

My driver's side suicide door has been frozen at the bottom for a long time... no problem, I just went to the passenger side... all except now the passenger side is starting to act funny. Oops! Time to get in there, bite the bullet, put up with the aggravation, and fix the damned thing.

[@Handy-Mann]

Hopefully it's an easy fix like I show and it's not all rusted. Best of luck!

[@uhih6717823]

If you live in the Rust/salted road area,- be prepared to remove the 3 small retaining nuts in the bottom of the door that holds the latch on . Cut the three studs off with a small wheel grinder and open door. You will probably have to grind the latch in half also to get the jaws off the loop deal. The latch is available from dodge or china. Dodge is 116 bucks, china is 50 to 80.00 I don't buy from China

[@melissabidwell2525]

Thank you!!

[@Handy-Mann]

Glad it helped!

[@martywells3037]

thanks..good clip

[@Handy-Mann]

Glad I could help!

[@garrythompson475]

If you don't bend (bend back together a little bit) the tabs on the rod connector, you will probably have the same problem again.

[@venomousnex9674]

Don't use a flat head the make tools for that just spend the 30 or so and get them