The Idahoan conducts an experiment to test the urban legend that baking a spray-painted part will harden the paint and make it as durable as a powder-coat finish.
Пікірлер: 60
@DarkMatterX12 жыл бұрын
In my experience a long, low process of curing spray paint at low temperatures (180 -220°F) for 4 to 6 hours does in fact provide a more durable coating. It's all dependent upon surface preparation. A uniform sanding layer to a 400 grit level, followed by a primer coat cured for 4 - 6 hours at the earlier temps. This step followed by 2 coats of color coat, each sprayed and cured separately in the same manner. This coating ends up being markedly more durable than an ordinary air cured rattlecan job. It's labor intensive, but it works. I've used it often for motorcycle parts, and they will withstand rock hits which would otherwise chip a standard paint coating.
@onpsxmember2 жыл бұрын
How much does it safe compared to buying the powder if it's already labour intensive?
@DarkMatterX12 жыл бұрын
@@onpsxmember I just don't like the look of powder coat vs a good paint job with clear coat. If you find both finishes equally aesthetically pleasing, my way makes no sense.
@onpsxmember2 жыл бұрын
@@DarkMatterX1 Usually I see powder coating with parts that'll see more abrasive wear or are positioned in a less visible place or to get a bit more texture for grip. I wouldn't use powdercoating for everything.
@PSUQDPICHQIEIWC2 жыл бұрын
My results are similar, though I tend to ramp the temperature up after a few hours. I don't have a powder coating setup, so I'm not at all interested in any comparison. I consider oven-cured paint to be a technique to provide a fully-cured part without needing to wait a month for the finish to naturally achieve full chemical and abrasion resistance. ... but then again, most people don't even know that a finish takes more than a few hours to cure at room temperature.
@shawnaburns51584 ай бұрын
I do tractor parts this way and the paint will not come off it's a great method
@stevest1300 Жыл бұрын
Oven baking is dangerous as hell. Even if she doesn't catch you during the baking, she'll smell it the next time she makes her crappy lasagna. You'll pay.
@shawnaburns51584 ай бұрын
Not if you vinegar clean the oven out afterwards,,put vinegar in a pan run the oven and then clean it out thoroughly,,I do it constantly and no problem
@summerforever67363 ай бұрын
man up!!
@Andi_Doci Жыл бұрын
Temperature and time matter a lot. Paint is a polymer so too much heat and time could damage it. I would do minimal temp on the oven for no more than 15 minutes, then allow for the item to fully cool off with sufficient time thereafter. An error I can spot in this "experiment" is that the main reason for baking the regular spray paint is the curing speed vs not baking it. So the benefit of baking is that you get very quick curing vs waiting for 30 days. So, you should have done a test where you spray paint the piece then wait 30 days. Then on the test day you spray paint the next piece and then bake it, then compare.
@wayneschrager50142 жыл бұрын
Interesting, I always enjoy this type of video. Thank you.
@qhack2 жыл бұрын
The baking technique is based on the type of spray paint used. For enamel paints, you get the best result if you bake it. For lacquer based paints, there is no need to bake.
@theARMORYchannel Жыл бұрын
yup
@Arthurian. Жыл бұрын
This is cool. I'm going to be baking my lower, this will be handy. Thanks!
@johnbennett28552 жыл бұрын
I think this is probably a carry over of baked vs air dried cerakote rather than regular spray paint
@250smacks2 жыл бұрын
What in Sam Hill are you wearing? You look like a mix between Christopher Lloyd from back to the future and an Amish dude from Nappanee Indiana.
@eabr28812 ай бұрын
I love your Superman curl. Lol, no offence intended. Thanks for the very informative video.
@rlbadger16982 жыл бұрын
Thank you, good to know.
@bustinbass78 Жыл бұрын
I paint metal lures. Spray paint is not used because it just does not stand up. A couple casts in the rocks and spray paint chips off. Oven cured powder coat is my goto because it is so durable.
@Smallathe2 жыл бұрын
Very interesting experiment. :)
@garycombs9435 Жыл бұрын
Oven curing is simply to cure the paint faster. That's why many car finishes are baked. It's mainly to speed the curing time.
@stefanmolnapor9102 жыл бұрын
Interesting, thank you
@louislarose66132 жыл бұрын
That was a really cool experiment ! Happy New Year From Canada To You and Family !
@Friedbrain112 жыл бұрын
For some paints, it does work, but finding the right ones could be expensive.I don't think that it would eb as durable as a powder coating though.
@GregariousAntithesis2 ай бұрын
Sand blast paint with rattle can enamel and bake at around 220 makes it tough as nails and way more chip resistant than powder coating.
@ThePatriotParadox2 жыл бұрын
I had to re drill some trigger pin holes in my polymer lower, finally fixed them with JB weld, do you know of any any good hardening spray paint or such I can go over it with to ensure they don't woller back out?
@ifell32 жыл бұрын
Project farm would have made some sort of weighted jig aha. It just cures it quicker
@stoneyswolf9 ай бұрын
Air drying can take weeks even months to fully cure 100% so all things being equal both fully cured there's no difference.
@maxheadspace29752 жыл бұрын
Suggestion: HEAT the sample to 500 degrees before applying the ENAMAL spray paint.
@liljohnp1322 жыл бұрын
I heat smallish parts with a propane torch before painting. Seems to help.
@onpsxmember2 жыл бұрын
Nice M&M's fight.
@charleenheath61162 жыл бұрын
Sure like your white Lab Coat. Gives the video a "Mad Scientest" flavor. Thanks for the insight. leenotcharleen
@WildHorsesOfCourse Жыл бұрын
I'm glad to see that Andrew Luck is enjoying retirement.
@LUvS2RoOT Жыл бұрын
🔥🔥
@MrAvidOutdoorsman Жыл бұрын
Why wouldn't you have used steel instead of aluminum?
@fuoman100 Жыл бұрын
Your testing methodology is not adequate to get an unbiased test. You are in yourself creating a false test by providing pressure on your own. From your video you even say you provided more pressure. A truer test would be to test all 3 samples under the same test in a way to remove your physical bias. Eg put the samples in a rock tumbler for a set length of time each or similar test to remove your inconsistency from the test. However good effort.
@mattkissmyasstyrants86762 жыл бұрын
You took a lot of things apart when you were a kid huh? Lol, I did too. 😁
@andre1987eph4 ай бұрын
2:12 the answer must be yes since he has an oven 2:12. 🙂
@raygodbout9 ай бұрын
wire wheel with no safety glasses?
@IanThompson-sb8hh9 ай бұрын
I was really only interested in the maximum safe bake temperature to use - the 1 thing that was missing from this video. So, not much use to me...
@harryjoe8602 жыл бұрын
Did you use appliance paint? That stuff works when you bake it
@larryalexander48332 жыл бұрын
Ceramic paint is more durable
@harryjoe8602 жыл бұрын
@@larryalexander4833 that too
@250smacks2 жыл бұрын
My ak builds look great. Rustoleum appliance epoxy works great! I called that company and asked if they were eventually come out with more colors. Told me no🥺
@harryjoe8602 жыл бұрын
@@250smacks good to know!
@TronVila Жыл бұрын
Rusto appliance epoxy is pretty incredible for a cheap spray paint. I’d bake parts at 170 for a few hours and it gets rock hard
@TheStigma5 ай бұрын
What does "standard WD40 method" mean for powdercoating? Using the oil to make it stick instead of an electrostatic gun? Is there any video on that? It sounds interresting
@TheIdahoanShow5 ай бұрын
kzbin.info/www/bejne/pmTJZ4qfhcl0jsk
@TOMAS-lh4er2 жыл бұрын
Hey Brother , what is the WD-40 method you mentioned ?? thanks .
@TheIdahoanShow2 жыл бұрын
kzbin.info/www/bejne/pmTJZ4qfhcl0jsk
@crookedaxle13 күн бұрын
You run an unshrouded wire wheel with no eye protection? Good luck with that.
@D56t37-cu7ol Жыл бұрын
I used to paint cars. After the fresh paint sits in the sun for a few weeks the paint is much tougher. I think it's a combination of UV, infrared, and just plain heat.... I don't think heat alone can compete with the sun...
@cowsongs Жыл бұрын
The paint, even the enamels, used for painting cars is nothing like the spray enamel from a rattle can. I think most of your improvement came from the fact that the auto paint simply finished curing and hardening over a few weeks.
@embededfabrication44829 ай бұрын
Powdercoat heated cause no solvent
@raging_rhino2582 Жыл бұрын
Very scientific....using the edge of a shell casing? Lol
@grezelnick Жыл бұрын
I'm curious... What is the WD40 Method for Powder Coating?
@TheIdahoanShow Жыл бұрын
kzbin.info/www/bejne/pmTJZ4qfhcl0jsk
@DebakulumToughguts2 жыл бұрын
👍 für den Algorithmus
@chrisdaniels4674 Жыл бұрын
Don’t drink the water
@TheBadurpa Жыл бұрын
You failed...... I did not learn anything..... What Temp.....?