Dometic Thermostat Control in an Airstream International Signature

[@JonnyTuneIn]

*Works so well **Fastly.Cool** that it only requires daytime operation until high temp and humidity are overnight. It is difficult to get to side filters, but back is easily accessible.*

[@asktheuniverse2718]

Also if it starts not working or showing Aqua instead of furnace, just press the up and down buttons simultaneously. Also when you go to set the program once you have programmed it to the temperature at the time you like, just 'let it be' and it will continue blinking and then it will go away automatically, it will be set so dont worry. And the thermostat will revert back to your manual option for use during the daytime. Hope this helps!

[@squeezebox63]

Thank you, I've been trying to sort this out for for 2 seasons. The dealers are not even up to how to use it. Thanks for the understandable demo.

[@so_cal_mom]

Please make more videos. I just got a 2013 International Signature and I am a total newbie. Your video was awesome!

[@jimk1050]

Good introduction but I'd like instructions how to program furnace to switch to 70 degrees at 5:30 am and to 60 degrees at 10:30 pm.

[@davidrossi2293]

Can you please make video on zones and programming 🙏

[@halsilzly5884]

I have an Alpine 37FL and can not ever get my heat figured out! Very frustrating ! I think I have 2 zones. And what about the clock? Does that have to be set to the current time? Heat Pump? How do I use that? It's all very confusing to me. Please send me somewhere for a thorough lesson on this ridiculous system. Thank you

[@serifv2525]

This was extremely helpful. We’ve only been in our trailer for a week and we’re going crazy. Would like something on the program button and also reset. Please and thank you!

[@whereinthehellarewewill1363]

That’s my main question as well. Driving me batty!

[@mnolasco11]

I have a 3 zone DOMETIC system with one Heat Pump in each zone in my 2022 DRV Full House JX450. Zone #1 has a Dometic Penguin II Rooftop Multi-Zone Air Conditioner with Heat Pump. Zones 2 and 3 are AC units only. I also have a propane furnace. Zone 1 unit was recently replaced. Prior to replacement, the Dometic thermostat would operate the furnace. Since replacement, when set at zone 1, the thermostat no longer displays furnace options. I no longer have a way to turn the furnace on. I have tried to call the dealer and Dometic, no help so far.

[@asktheuniverse2718]

Skipping the program button... Need that

[@tenapeters8107]

I need basic information. I hate it when my AC and furnace fight each other. Hard to figure out

[@lydiascurek90]

I have a thermostat in my main area that works but I can't get the one in t bedroom to work

[@whereinthehellarewewill1363]

How do you turn off programming?

[@keithmoore7515]

This is the Thermostat I have but I do have the 4 zones, It has furnace mode, heat pump mode, cool mode... Ect. I have a 2013 Keystone Alpine 3555RL I can't figure this thing out to save my life!! Could you direct me to a source that would explain? Thanks So Much....

[@aldoraydavis126]

I have the same and I cant figure it out iether any luck ?

[@Therealgirlinthedesert]

That was no help we’re still freezing in our new rv at 66 degrees in our rig 🥶

[@patrickmelson4745]

Can I run the fan furnace only? Not heat but just the furnace fan for circulation?

[@richp4449]

What about Program????

[@so_cal_mom]

I SO needed this! Thank you!

[@musclerocker]

The zone won’t stop blinking and I can’t change anything

[@markenloe1265]

Great information....

[@robertswift1112]

Mark Enloe Thank you!

[@rxonmymind8362]

Furnace +Auto mode. Got it. Thanks. Now to program it.

[@davidmayhall6567]

My thermostat is the same as yours but the only thing I see is the blue backlight and the clock nothing else works? What's wrong? Help

[@scottcampbell5087]

David - Did you ever find out how to fix this? I am searching for the answer right now. I see this comment is one year old but I thought I would try to ask.

[@stolzb]

10K VIEWS! WOAH DAD

[@stolzb]

nerd

[@stolzb]

nerd

[@stolzb]

nerd

[@HEROICRacingApparel]

Cool

[@crappiebuster3771]

You didn't cover the one control that causes the most confusion - Program! The manual is almost silent on this function and how the different time settings work. Waste of time to watch this video.