Drone motor not spinning | ESC calibration 30A Simon k ESC [SOLVED] Brushless motor not working

How to make Quadcopter using APM 2.8 : • How to make Quadcopter...
APM 2.8 flight controller setup tutorial: • APM 2.8 flight control...
Drone Experiments:
• DIY projects || Tech a...
Follow us on Instagram :
/ tech_at_home
Like us on Facebook :
/ tech-at-home-220885266...
#apm2.8 #esccalibration #ESC #droneesc #quadcopterapm2.8#droneusingapm2.8#techathome
Thanks for watching!
Like Share and Subscribe

[@sujalchauhan8346]

This is what i needed to run my new a2212 10t 1400kv motors and i have no clue about why my esc was beeping and what to do even though i was giving 12v to it through adapter and pwm signal from arduino. Thank you brother, you taught me something new...

[@techathome]

Welcome ❤️

[@나홀로할베-f2d]

After connecting 2 motors to 2 ESCs, without knowing to remove the red wire on one side of the BEC, I connected them together to the servo controller of 1 and tested the operation for about 30 minutes?? So, only one motor worked, the other motors operated randomly, and in the end, the ESC on the motor side, which was working well, was damaged and did not work at all. When I went to KZbin, I saw a video about removing one BEC. I removed the ESCs one by one, reset them, and tested them. Of the two ESCs, only the motor side, which had been malfunctioning uncontrollably, works. When I turn on the power, the motor makes the same beeping sound that it made before starting, but even when I move the throttle, it works. The motor doesn't move at all. Is there no way to save it??

[@johnbrock3392]

Thank You! This fixed my non running motor :)

[@techathome]

Welcome!

[@antonisherboy355]

How I can find it even though I am not using any other flights mode except stablize

[@navinsingh1730]

Hi, I am trying to control the ESC with a microcontroller but it is not working. It beeps indicating no input signal detected. I am using a raspberry Pi pico. I also tried connecting the power to the bec but didn't work

[@achallavinay8919]

Which version of mission planner is best for apm2.8 ? 1.3.49 and latest version are not working

[@techathome]

Try this: firmware.ardupilot.org/Tools/MissionPlanner/archive/MissionPlanner-1.3.68.msi

[@puneet1307]

Then which version working fine? Please tell

[@techathome]

Download this: firmware.ardupilot.org/Tools/MissionPlanner/archive/MissionPlanner-1.3.68.msi

[@Xavierfun12345]

When I increase the power the motor is disconnected and again connected... 😬😬😬 What to I do

[@abdullahsaqib8471]

Most probably your battery is dead. Check voltages of each cell of battery with multimeter check If either cell is below 3v .

[@elad3958]

This may be what I need. Thank you brother

[@techathome]

Welcome

[@SerjGhiriPianowl]

it used to work just fine, now i don't know why only 1 motor run after calibration but the other three after i plug the baterie and the throttle is max i hear 3 beeps but thats all, the 3 motors wont turn any solution please

[@Techzino-vibe]

Calibrate your ESC one after the other.

[@SerjGhiriPianowl]

@@Techzino-vibe true, that was the problem indeed but i fixed it back then and graduated with the project haha thanks for the helpgreat content!

[@GorantlaSurendra]

Bro my bldc motor not running but its beeping sound what is the problem??

[@techathome]

I think ESC Problem.

[@Timepass-fn2vn]

Hello, I saw all of your videos I am building a hexacopter but my drone tilts to the one side I don't know what the problem is I have caliberated the esc's 4-5 times just as you told, I even tried changing motors as well I am using apm 2.8. Please help

[@techathome]

Have you calibrated ESCs using flight controller? kzbin.info/www/bejne/oHnEinR3lLCgbbs Check the motor layout and direction of rotation Also , check propellers (clockwise and counter clockwise)

[@abdullahsaqib8471]

Try recalibrating your compass again.

[@AkashSharma-no8eg]

switch to d shot esc

[@duartepaintinghandymanservices]

Can you also do this through betaflight?

[@techathome]

Steps remain same.

[@juniosilvadearaujo8487]

How did you manage to bind the receiver with the radio with this tx on the radio screen, mine only binds with the AFHDS 2A in off teach me there

[@techathome]

Binding TX and RX(flysky fsi6) : kzbin.info/www/bejne/d3ixq2ichbt1nqM

[@juniosilvadearaujo8487]

@@techathome No you don't understand, give me your WhatsApp contact I'll explain it better with photos

[@Mr_Moto_Gen]

how much voltage battery have you used?

[@techathome]

11.1 volt, 3S

[@achallavinay8919]

Is this process same for kk2.1.5 flight controller drone also? Because my drone is tilting on one side

[@techathome]

Yes You have to calibrate ESC in 2 methods for stable flight 1. Do the steps shown in video for all 4 ESCs 2. Calibration of ESCs using KK board: -Remove supply -Switch on TX and keep throttle to max -Press and hold 1st and 4th button of KK board and connect battery -you should get " throttle pass through" on screen of KK board - wait for few seconds and decrease the throttle -wait for few seconds - remove battery Note: don't remove buttons of KK until all steps are done in method 2

[@debprasadbanerjee5005]

Did it solfve?

[@SRai123456]

hi, i did all the calibration, when i fly the drone, its did not stay in a position although i did not move it.

[@techathome]

I have given the motor layout in this tutorial, You can check once : kzbin.info/www/bejne/iWi5i2pva7xrjKM

[@pabitragamer3192]

Vai bike wali vedio kaab ayegi gear and brake

[@techathome]

We will make it soon Clutch part need some work

[@pabitragamer3192]

@@techathome Thanks for replying vaai

[@vikramsridhar4486]

Sir in my transmeter ch is not working when i connect my servo also its not working how to make a program for ch3

[@techathome]

Have you binded your receiver with transmitter?

[@faracollo12]

i have a problem my motor doesn’t start and do any beep when connected i have a flysky i6x can someone help me

[@techathome]

Steps will remain the same on any model of Tx and Rx. Try to change motor and ESC once.

[@rajjatav4100]

Befor calibration,is receiver should be bind with remote fsi6

[@techathome]

Yes, it should be binded.

[@thisisakr]

I am able to do individual PWM calibration but when I try to connect it to pixhawk and use PPM calibration it's not working. And motors keeps beeping every second

[@techathome]

Can you check this once : kzbin.info/www/bejne/hl6rk4mVmZyXf7c

[@KLERocketryTeam]

I want to rotate the motor in reverse also, so how do i calibrate it?

[@techathome]

Keep centre yellow wire as it is and just interchange red and black wires at the motor

[@abduxaliljunior8871]

Good describition for me!

[@techathome]

Thank you 👍

[@Rowdy_rider_Lalith]

Do it with fs ct 6b

[@techathome]

Calibration steps remain same

[@Rowdy_rider_Lalith]

@@techathome thankyou bro

[@rajeshsahu1217]

Hello brother i tried your step and it producing same beep before and after but my motor running roughly like vibrating , please connect with me

[@techathome]

Repeat the calibration as shown again. If issue is exists, then try with different ESC.

[@cricketnewstamil640]

Sir please help me my drone wings are rotate but fly

[@techathome]

Check the motor layout and the propeller direction. kzbin.info/www/bejne/i4iUXpqJrriarsk

[@mburhanudin7767]

Salam sejahtera untukmu tuan....saya mempunyai esc simonk 30a seperti yg anda punya.....ada permasalahan dengan esc saya .kenapa esc saya berbunyi beep putus2 tidak henti2.mohon solusinya

[@techathome]

What is the problem

[@mburhanudin7767]

@@techathome terima kasih atas perhatiannya Permasalahannya karena saya pemula dan belum faham dengan rc plane. Kebetulan saya merakit diy rc plane arduino. Jasi permasalahan diatas sudah selesa.trima kasih banyak.i

[@debprasadbanerjee5005]

The drone vibrates and tilts

[@marshalgamer8973]

Me also

[@lightinggaming5202]

Vibrates hai to propeller balance karo ❤

[@The1971master]

facing problem in high gps hdop

[@naitikjimaurya8099]

My drone motor is not working i do esc calibration many times

[@techathome]

Need to check with other ESC once to find out where motor is working or not

[@Bhavesh8834]

Beep sound not coming

[@techathome]

Still try to follow the same step and see if motor works.

[@faracollo12]

probly if the motor doesn’t beep and doesenta start the esc is broken

[@techathome]

Yes

[@tensivegamerz4671]

But the reciver is working with The esc is it means the esc is broken ??​@faracollo12

[@antonisherboy355]

Aoa bro help me

[@WRIFE-369]

My throttle is not getting armed

[@vivekyadav9063]

Sir my mortors are only vibrating not rotating I had did the setup more than 5times 🥺

[@techathome]

If ESC is not working, then also this might happen, You have to check the same motor with different ESC Also have you done the connection as shown in the video?

[@yogirajshirolkar700]

We have design flight controller using Arduino and mpu 6050 our problem is our motors are not rotating only beep sound is coming

[@techathome]

Have you calibrated ESCs after buying.

[@yogirajshirolkar700]

@techathome yes

[@yogirajshirolkar700]

How can I contact you

[@techathome]

Mail If you have Transmitter and receiver, connect ESC directly to receiver and try to check if motor is running.

[@yogirajshirolkar700]

@@techathome ok

[@lukalama2218]

I have a 6 motor drone, when I want to fly it, 3 motors turn off and don't spin, what is the problem, and what is the solution, I use esc simonk 30A

[@techathome]

If you are using APM you can follow this tutorial : kzbin.info/www/bejne/oHnEinR3lLCgbbs Check motor connection, ESC calibration

[@Lazyvella-p6m]

I am hearing 3 beeps

[@techathome]

No issues if you get more beeps

[@antonisherboy355]

My Drone take off after 50 % throttle

[@suvedhant]

Can we re calibrate also are it’s only once we can set ?

[@techathome]

You can calibrate any number of times