Dryer Won't Heat Up Or Dry Clothes - DIY How To Fix Heater In 2024

  Рет қаралды 1,582,122

jeffostroff

jeffostroff

Күн бұрын

Пікірлер: 2 400
@jeffostroff
@jeffostroff 4 жыл бұрын
💲 Samsung Dryer Heating Element DC47-00019A Kit w/Thermostat: amzn.to/2TEJ4kp 💲 Dryer Exhaust Telescopic Periscope Kit Whirlpool 8171587RP: amzn.to/38utZay 💲 Fluke 87-V Digital Multimeter: amzn.to/2LK8etM 💲 Klein Tools MM400 Multimeter, Auto Ranging: amzn.to/38uwucS 💲 Milwaukee, 2415-20, Cordless RA Drill, 12V, 3/8 in. amzn.to/3czTbj9 💲 Milwaukee 2415-21 M12 12V 3/8" Right Angle Drill/Driver Kit amzn.to/38qhm0m
@SouthBaySteelers
@SouthBaySteelers 4 жыл бұрын
wanted to let you know Pro Appreciation week is coming - March 23
@jeffostroff
@jeffostroff 4 жыл бұрын
Any good deals you know about?
@SouthBaySteelers
@SouthBaySteelers 4 жыл бұрын
I haven't had time to look.
@clsybtrfly
@clsybtrfly 4 жыл бұрын
We have a samsung and have replaced the heating element twice in a month then found some sensors that aren’t all on the element were bad so we replaced them. We snaked the dryer vents out with a tool like you have and our drill , got a ton out. Well the dryer worked great for 3 days and back to not heating up. Guess we will have to buy a new one because it’s not the element or sensors we found. At a loss now
@roccobollotta2277
@roccobollotta2277 4 жыл бұрын
I followed the video perfectly and all went well. Just one thing strange, ohm test checked good on all the prongs on the old heating element after removal and the coil though mostly black was not broken, I did find the plate cracked exactly in the same place as the one in the video. So I went ahead and changed everything that came with the kit, including the Thermal Fuse and the Thermostat. After I thoroughly cleaned the interior I could get to of the dryer, and thoroughly cleaned the lint vent all the way to the roof I reinstalled the complete unit. After installation everything worked perfectly, dryer is heating well as new again. Why it stopped heating when ohm check checked good is still a mystery unless the crack in the plate holding the coils was a factor.
@kristensavage7360
@kristensavage7360 3 жыл бұрын
Just want to say THANK YOU! I'm a mom and when my dryer went out I was ready to cryyy (we had our vent cleaned so I knew that wasn't the issue). I found your video and thought okay, this is crazy but I'm going to do it. I DID IT!!!!! I haven't been this proud of myself since childbirth 🤣🤣🤣
@jeffostroff
@jeffostroff 3 жыл бұрын
You are so welcome!
@babstering
@babstering 2 жыл бұрын
I have the same feeling cause I did it awesome video
@opheebop7632
@opheebop7632 2 жыл бұрын
Lol the end
@lupejeffe6047
@lupejeffe6047 2 жыл бұрын
Ima father and I feel how u feel 😂😂
@SoapySoul1111
@SoapySoul1111 2 жыл бұрын
Girl power 💪yessss! I know that feeling as I was in the same situation with my washing machine drain pump. It went out and I wanted to cry, but I successfully fixed the pump and have been on fire fixing things ever since. I was a little bit nervous about the dryer as I have only changed the cord and nothing more, but after reading your comment and with the help of this video I have all the confidence in the world that I will be able to accomplish this task. Thanks so much 🙏
@annhatch4326
@annhatch4326 Жыл бұрын
Absolutely THE BEST How-To video I've ever seen! I'm a 56-year-old woman, and just finished replacing the heating element on my dryer! If you're not a teacher, Jeff, you missed your calling...Thank you!!!!
@jeffostroff
@jeffostroff Жыл бұрын
Thanks Ann, glad you liked it and Glad it helped!
@Gulfcoasting
@Gulfcoasting 4 жыл бұрын
I just can't thank you enough! I'm a 56 year old little lady and I repaired my dryer for $23! Your video was perfect!
@jeffostroff
@jeffostroff 4 жыл бұрын
Awesome, glad to hear you were bale to fix this yourself!
@Alycanj
@Alycanj 3 жыл бұрын
56 year old Honey Bear...
@lorimav
@lorimav 3 жыл бұрын
I am 61 and would not attempt this but I appreciate the information about the annual cleaning of the vent, the link to the brush, and the information about proper venting. That alone was worthwhile. I know someone who did have a dryer fire.
@kris10tackles
@kris10tackles 2 жыл бұрын
Thank you so much! We noticed our dryer wasn’t heating on Friday morning. I found your video and ordered the part within minutes. It arrived the next day and we were easily able to get it swapped out. No stress, no hassle, no having to wait for someone to come out. Thank you so much!
@jeffostroff
@jeffostroff 2 жыл бұрын
Glad it helped Kristen, and thank you so much for the $4.99 $SuperThanks!
@Postsforlife
@Postsforlife 3 жыл бұрын
You sir, have allowed me to fix my dryer within twenty-four hours, and clean out my wall vent like a champ. Didn’t cost but $30 for the entire heating element unit and $18 for the vent brush. You’re a saint and a life-saver; the folks at my local Samsung wanted to charge me $100 just to come out. God knows what they’d charge after parts and the time it took them.
@jeffostroff
@jeffostroff 3 жыл бұрын
Thanks, I'm glad you liked it!
@mluc1111
@mluc1111 2 жыл бұрын
Honest person will charge $200 , dishonest $500
@daviddenison2097
@daviddenison2097 2 жыл бұрын
Where did you find parts???
@jerkel
@jerkel 2 жыл бұрын
@@daviddenison2097 you can get a replacement on amazon, just look for the parts number on the coil heating metal plate. it's around $25+ depending on shipping
@daviddenison2097
@daviddenison2097 2 жыл бұрын
@@jerkel Hi love one. U R right except the one I saw is $245. Is there knock off brands I missed?
@yolandasolis2718
@yolandasolis2718 4 жыл бұрын
Yay! I did it! I replaced the heating element in my Samsung dryer after suffering for 6 months having to hang clothes outside everyday. Thank you so much! Your video was so clear and precise and I followed it, step by step. I also bought the Klein tools meter you recommended to make sure the other parts weren't failing. I'm over joyed and feeling so accomplished. If this woman can do it, anyone can do it! Just follow Jeff's video and you can't go wrong.
@jeffostroff
@jeffostroff 4 жыл бұрын
Awesome Yolanda, congratulations on getting that done yourself.
@juanch2031
@juanch2031 4 жыл бұрын
What is your model dryer. How you order thanks
@yolandasolis2718
@yolandasolis2718 4 жыл бұрын
@@juanch2031 My Samsung dryer Model # DV393ETPARA/A1. I purchased the heating element on Amazon from the Brand: DOK Parts Best. I don't know the direct link to it. I also purchased the Klein tools meter recommended in this video. I wanted to check before assembling everything back together. The meter will help you with other projects, too. Seven months later, the dryer is working well. To avoid any mistakes in re-assembly, I took pictures of every part or wire I disconnected. I referred back to the pictures and video with every step. This is by far the best step-by-step video I have seen for this. Thank you Jeff.
@romanasky6820
@romanasky6820 3 жыл бұрын
I'm about to try this. I'm a grandmother. But I think I can do it, Yolanda! It is worth a try. :)
@tonymaiqi5337
@tonymaiqi5337 2 жыл бұрын
Yolanda, is your dryer not generating heat at all? or there is still little heat generated before you fix it
@kanchr7537
@kanchr7537 2 жыл бұрын
Thank you, Jeff . Husband and I did it together and it was more of fun , with no frustration at all. Thought we would end up yelling on each other and would mess up somewhere along the way. You were so patient with all your details. Just amazing.Thank you/
@colleenmcquade8294
@colleenmcquade8294 3 жыл бұрын
I've never stumbled upon a do it yourself repair video that actually made sense and felt like I could do it, thank you! I was able to fix my dryer myself and felt confident that it was done right. Thank you!
@jeffostroff
@jeffostroff 3 жыл бұрын
Glad it helped
@VaVaVroomTX
@VaVaVroomTX Жыл бұрын
Thanks to your video I was able to fix my dryer and do some proper maintenance without spending a ton of money! Thank you so much for this PERFECT video!!
@jeffostroff
@jeffostroff Жыл бұрын
Thanks so much for your #4.99 $superThanks!
@tonycabay6813
@tonycabay6813 Жыл бұрын
Dryer stopped heating, searched and came across this video. Saved us HUNDREDS of dollars. Amazing detail showing how to take the part out, and how to put it back in. Ordered off Amazon witht the part number in the description, and it arrived the next day. Put it in, following this video, and we are back to wearing dry clothes. Cannot thank you enough.
@rpatel8978
@rpatel8978 3 жыл бұрын
great video, no fluff, no auditioning, no bs...just pure info....i couldn't wait to add my comment so doing it while the dryer is still open on the floor, but I know that I am going to save the money for a brand new dryer or an expensive service call by following this video.
@jeffostroff
@jeffostroff 3 жыл бұрын
Glad it was helpful!
@tashamariestevens2269
@tashamariestevens2269 2 жыл бұрын
My husband and I just replaced the heating element in our dryer. We are beyond grateful for your expertise and willingness to share. The instructions were step by step, detailed, and clear. Thank you.
@jeffostroff
@jeffostroff 2 жыл бұрын
That is awesome!
@amylane5573
@amylane5573 2 жыл бұрын
This video was extremely helpful! Thank you for the detailed step-by-step! My husband watched, re-watched, and paused along the way to a successful ending and a dryer that now works! Because of your easy-to-follow steps, we were able to work as a team and we both learned something new! Thank you for taking the time to make such a helpful guide!
@tonymaiqi5337
@tonymaiqi5337 2 жыл бұрын
Amy, is your dryer not generate heat at all? or there is still little heat generated before you fix it
@donnerproductions2092
@donnerproductions2092 10 ай бұрын
Thanks! Solved our problem and I learned a lot about our Samsung dryer!
@jeffostroff
@jeffostroff 10 ай бұрын
I'm glad to hear it worked and thank you so much for the super thanks
@_K24
@_K24 Жыл бұрын
Thanks so much for the great tips. This video helped me fix my dryer (heating coil snapped right in the middle like you said). Replaced it and working great again. Much appreciated!!
@jeffostroff
@jeffostroff Жыл бұрын
Thanks so much for the $superThanks, I'm glad the video helped you out!
@murrayherron3893
@murrayherron3893 4 жыл бұрын
First class KZbin University how to video ! I cook booked it the whole way and got perfect results the first try. Excellent tutorial Jeff, much appreciated. We subscribed to your channel and look forward to our next project. BTW, there’s an air leak on the shuttle, we’re throwing your contact info their way.
@jeffostroff
@jeffostroff 4 жыл бұрын
I'd love for NASA to call me!
@kgreene3047
@kgreene3047 4 жыл бұрын
I’ve been watching DIY KZbin videos for 3 years and this is the first one I’ve commented on. That was the best fix it vid I’ve seen. Everything was exactly what I dealt with and I went right thru. I got it all fixed up super fast. Thank you very much!👍👍
@jeffostroff
@jeffostroff 4 жыл бұрын
Glad it helped Kevin!
@Mikerobertsonsells
@Mikerobertsonsells 2 жыл бұрын
You are a great teacher. Thanks to you, no cuts on my hands, & no curse words. My dryer is FIXED.
@jeffostroff
@jeffostroff 2 жыл бұрын
Glad to help Mike!
@joannmcelmurry9433
@joannmcelmurry9433 25 күн бұрын
Jeff, you are my hero!! You provide a excellent video that allows a 68 year old widow to replace the heating element in her dryer! THANK YOU!!!!!!!!!!
@robertallen8237
@robertallen8237 5 ай бұрын
100% the best how to video I have ever watched on you tube my daughter and I just finished this repair and we now have a functioning dryer again and I only spent 25$ for the part. Thank you sir, your video was plain, clear and easy to watch without a lot of BS that some people wanna throw in!
@CalebOhh
@CalebOhh 3 жыл бұрын
Heads up, if you just unscrew the "bottom bracket" that you refer to at 9:26, you don't have to use your "stubby little Phillips" to blind unscrew the bottom bracket. You can keep the bottom bracket in the dryer and remove the heating element's housing. Great video, this was extremely helpful!
@donknotts33
@donknotts33 2 жыл бұрын
That's fine you can get the heater loose but there's no way to get the heater out with that stand in place.
@kirkj101
@kirkj101 2 жыл бұрын
I tried this but I couldn't do it on this model without removing the bracket. Is it physically impossible? Seemed like it to me, but maybe a professional could. I agree with his decision to show the process of removing the stand, but definitely good to know you can if you're experienced.
@tcmcintosh5256
@tcmcintosh5256 4 жыл бұрын
Best darn DIY vid I have seen in my 54 years! Thanks Jeff!
@jeffostroff
@jeffostroff 4 жыл бұрын
Wow, thanks!
@karenarcher3175
@karenarcher3175 4 жыл бұрын
Just sending a “high five” to you Jeff for a most comprehensive video that enabled us to disassemble, replace the element (which by the way had the element broken and the metal housing cracked in exactly the same place as the one you showed in the video), clean and reassemble very easily. Great step by step detail with clear camera shots! Thanks!!
@jeffostroff
@jeffostroff 4 жыл бұрын
Yes! Helped another one! Thanks for watching Karen!
@deejohnson5163
@deejohnson5163 4 жыл бұрын
Probably engineered to break.......buy, buy, buy.
@carlosluck1704
@carlosluck1704 3 жыл бұрын
In my case the resistance broke exactly on the same spot, with the frame cracked on the same spot, except that there was no obstruction in the exhaust duct that could cause overheating; we clean it regularly. Well, it's been in use for 7 years, so this might be just regular wear. I agree that it must have been designed with that weak spot built in.
@Troy-Sheets
@Troy-Sheets 3 жыл бұрын
@@jeffostroff Just repaired mine thanks to your video and it was also broken in the exact same spot. Thanks for the amazing video!!!
@jazzchamp
@jazzchamp 2 жыл бұрын
Add another to the list that was broken exactly the same way and fixed by simply following your video. Let me just echo everything that Karen and so many others have said! Superb!
@sflood106
@sflood106 7 ай бұрын
Just changed the part. Thanks for the video. It worked and saved me money.
@thepolytheist
@thepolytheist Ай бұрын
I used this video to help me fix my Samsung dryer two years ago, and I just used this video again for the same fix. Piece of cake. Thanks so much.
@jeffostroff
@jeffostroff Ай бұрын
That’s awesome, glad to hear the video is still helping people!
@smurfslayer10
@smurfslayer10 3 жыл бұрын
This is one of the best DIY videos I have seen! Great detail, you cover basic maintenance and the importance behind it. You rock! Thank you for taking the time to record this.
@jeffostroff
@jeffostroff 3 жыл бұрын
Wow, thank you!
@dansmith422
@dansmith422 3 жыл бұрын
Very helpful! I had trouble fitting the repaired heater enclosure into the round hole at the back after replacing and re-assembling. Kept falling out as I positioned the bracket underneath. Was made easier by attaching the bottom bracket back to the heater enclosure (after sliding the enclosure back into the dryer and reattaching wires) with the single screw on the tab of the enclosure, then positioning everything, and then securing the bracket at the bottom with the screws. Also, the heater enclosure has a tab that has to slide into a slot in the bracket, at least on mine. That threw me for a bit - again easier to attach them back together first, then position and complete the final re-install.
@palawanbeans
@palawanbeans 4 жыл бұрын
This video really helped me with the same Samsung dryer. Maybe you should make a video on what dryer to buy that doesn't require so much work like this Samsung.
@jeffostroff
@jeffostroff 4 жыл бұрын
They all do. My old Whirlpool DUET same thing.
@jamesgoings
@jamesgoings Жыл бұрын
Absolutely the BEST video I found. You eliminated unecessary steps and saved me hundreds of dollars for a repairman. Keep the great videos coming. Thank you so much.
@jeffostroff
@jeffostroff Жыл бұрын
You're welcome Jim!
@wendyalderson6742
@wendyalderson6742 Жыл бұрын
Absolutely the best DIY video out of the hundreds I've watched. The reminder to take a picture of the wiring?! Brilliant
@jeffostroff
@jeffostroff Жыл бұрын
Glad it helped wendy!
@patrikmschneider
@patrikmschneider 4 жыл бұрын
My forever tip I've got as an becoming engineer back in 1976, during studies was, that I always have to think about the one who works on any engine/machine with the screwdriver! I NEVER forgot about that! Had to smile about your brand related comments! But you find these genius everywhere..! Free translation from German wording: "Yesterday I did not know how to spell engineer, today I am one (of these)!"
@jeffostroff
@jeffostroff 4 жыл бұрын
Maybe these machines were not designed by engineers, but rather some people from marketing left over after the engineering team was laid off.
@Rextrent
@Rextrent 3 жыл бұрын
@@jeffostroff Good answer!
@SiegeTF
@SiegeTF 3 жыл бұрын
I think they make it as hard as they can to encourage the use of servicepeople. There'd be almost no need for them if everything was easy to fix!
@billdoutt4577
@billdoutt4577 4 жыл бұрын
Excellent video! Your advice was right on. The walkthrough had just enough detail but didn't get bogged down in banter. You described and linked exactly what was necessary for the job. Nice freaking vid! Just saved me a bunch. I think these heating elements are just low quality. My dryer is 4 years old, the vent is only a few feet long and was essentially clear and I clean the lint filter after every load. The plate was cracked on mine too, just like the one you showed. Anyway, thanks!
@jeffostroff
@jeffostroff 4 жыл бұрын
Glad it helped! On my old Whirlopool DUET dryer, they failed every 2-3 years. Probably don't last any longer unless you clean out all your ducts up tot he roof at least once per year. I get lazy and wait until my wife complains the dryer is not drying the clothes anymore, meaning heat exhaust is not exhausting out, so dryer overheats.
@gavingreen5031
@gavingreen5031 3 жыл бұрын
Super helpful video that goes into great detail. My model was slightly different, but the information he gave was a great step by step demo to troubleshoot the issue, and opening up the whole machine. The detail he showed in testing the existing heating element to show the closed and open circuits was great. Found the broken heating element and was able to replace. Greatly appreciated!
@jeffostroff
@jeffostroff 3 жыл бұрын
Great to hear Gavin!
@scocoh44
@scocoh44 Ай бұрын
I just wanted to say a huge THANK YOU for this video! I have a Samsung Dryer Model #DV42H5000EW/A3 (electric), and while my model varied slightly, this guide was 99% accurate and helped me tremendously. Instead of paying the local Phoenix, AZ Samsung factory rep over $200 in service and diagnostic fees-on top of parts and labor-or potentially spending $500+ on a new dryer, I was able to fix it myself for under $27 thanks to the part I found on Amazon. This video not only saved me a lot of money but also gave me the confidence to tackle a repair myself. I first found your channel through your insightful commentary on the Miami condo collapse, but this repair guide was a lifesaver. Thank you again for your excellent content!😀
@jeffostroff
@jeffostroff Ай бұрын
I'm glad you were able to fix it yourself! I'm happy I could help you save some money.
@ballaku
@ballaku 3 ай бұрын
I was afraid of changing a bulb at home but guess what, i just finished replacing the heating element of my dryer, can’t explain how proud i feel myself, all because of this video, Thank you very much sir, this is one of the best youtube video i have ever watched, Thank you 🙏🙏🙏
@jeffostroff
@jeffostroff 3 ай бұрын
Glad I could help!
@stevenjerauld2352
@stevenjerauld2352 4 жыл бұрын
Thanks for making such a detailed, well made video. I appreciate all the little details and reminders you included. It shows your experience, and certainly gives us laymen more confidence to try a repair like this. Keep up the good work.
@jeffostroff
@jeffostroff 4 жыл бұрын
Glad it was helpful! thanks for watching Steven!
@patrikmschneider
@patrikmschneider 4 жыл бұрын
Following the video, this is perfect, just one point is missing! Add some band-aid to the workplace. All parts are sharp like a Swiss Army knife. Other than that, my wife's one is fixed, so I can use it again! Cheers y'all!
@jeffostroff
@jeffostroff 4 жыл бұрын
Awesome, glad to help Patrik!
@daniellind6431
@daniellind6431 4 жыл бұрын
I second that! Got a few cuts myself throughout this repair
@TrukaLyf01
@TrukaLyf01 3 жыл бұрын
Yes! You will definitely be cut lol...thx for the video!
@Dragonwitch42
@Dragonwitch42 4 жыл бұрын
This was just perfect. Showed exactly what I needed to do an exactly which part was the issue. Thank you
@jeffostroff
@jeffostroff 4 жыл бұрын
You're welcome! Jay!
@brycehopper9397
@brycehopper9397 2 жыл бұрын
Sir, I sincerely cannot thank you enough for this video. I was able to pinpoint the issue, disassemble, replace the heating element (crack in the spring and frame, just like you said there would be), and re-assemble in less than a few hours total time (same day in fact as Amazon sent me the replacement part same day). Thank you so much and please keep putting out content like this!! Who would have thought for less than $30 I could fix my Samsung dryer!?!? You saved me hundreds of dollars!!
@jeffostroff
@jeffostroff 2 жыл бұрын
Glad it helped
@mirandamackenzie2098
@mirandamackenzie2098 8 ай бұрын
I did it!!! Thank you so much for your step by step instruction. My first small appliance repair! Another mom, very grateful and proud of myself!
@mrchowdary
@mrchowdary 4 жыл бұрын
Thanks Jeff. I was about to call Samsung service and do an expensive repair before watching your video. Could complete the repair under $25.
@jeffostroff
@jeffostroff 4 жыл бұрын
Holy cow, I'm getting 3 to 5 people day telling me the same thing, there must be a boatload of these Samsungs failing out there.
@bilbusb
@bilbusb 4 жыл бұрын
@@jeffostroff these things suck .. i know 2 ppl with the same issue.
@proanswers
@proanswers 4 жыл бұрын
Usually we see a code on the Samsung models (most not all depending if the temp sensor is driven by a circuit board: tS, t5, tC, tO, t0, tE, tE3, tC5, tCS, 1 tC, 1tC5, 1tCS, Extra Low light is blinking. * some units have a fault code that wont allow the dryer to start until the filter or vent is cleared. One has to ask are you getting no heat, low heat at high heat setting, just lo heat etc.- might not be the heating element coil. This is why we use diagnostic steps, basic electronic science and read a wiring schematic. VS most DIYERS and novices * even professionals shoot the parts cannon at the problem see what sticks (which is NOT diagnostic/critical thinking). HINT most wire schematics for dryers are taped behind or behind and inside the top control module (BONUS HINT on refrigerators there taped Behind the front grill, in the center or on the left side. Other common locations are on the left or right side by the condenser, or inside the refrigerator section inside the control panel)). Most show you the error code faults and most show you how to read the faults from there you can TEST the circuits, sensors, heating coils following the wire schematic to determine exact problem. If you cant test it you haven't found the problem. * like Jeff shows. Electric dryers are very simple machines (most are electron hogs) vs gas vs line clothes outside. IF I could recommend any purchase advise to consumers- STAY AWAY from all the sensor gadget features on a dryer (or washer or any appliance) you only need about 4-5 temp settings with todays clothes the rest of the crap manufactures throw on there is just plan nonsense i.e. sanitation settings. Dryer manufacturers use sanitation standards put forth by the National Science Foundation adding more settings and upselling is just marketing BS. Sure manufactures are thinking about a VIRUS sanitation setting.
@jeffostroff
@jeffostroff 4 жыл бұрын
The washer is smart and talks the app, but surprising the dryer does not, and no error codes appeared either which was surprising.
@garymccall9573
@garymccall9573 4 жыл бұрын
when should you see the error codes? upon start up? paused? is there a trick to get them to display?
@proanswers
@proanswers 4 жыл бұрын
@@garymccall9573 start up there should be a code display. Whats going on with your dryer?
@garymccall9573
@garymccall9573 4 жыл бұрын
@@proanswers it starts and runs but doesn't heat up. No codes on start up.
@russrockino-rr0864
@russrockino-rr0864 4 жыл бұрын
Hey Jeff! I just replaced the first heating element in my Samsung Dryer about a year and a half ago. The first element lasted about 8 1/2 years. You have to take several parts off to get to the element, but the procedure is very strait forward, as you show in your video. I also cleaned the vent pipe and now it is time for me to do it again. I only have about 6 feet of vent pipe to clean. I also replaced the lint screen at the time because it was torn and allowed bigger chunks of lint to get through. Thanks, Russ
@jeffostroff
@jeffostroff 4 жыл бұрын
Yes, keeping those pipes clean is the key to a long and healthy heating element lifespan.
@garrettchavez8156
@garrettchavez8156 7 ай бұрын
In less than 24 hours, this video helped me take apart my dryer, find the problem and fix it. 10/10 good sir. I owe you more than my views!
@gisogr
@gisogr Жыл бұрын
The gift that keeps on giving. Thank you for such an awesome, user-friendly how-to. Your directions worked like a champ, saved me a few bucks, and gave me my 10-seconds of fame here around the house.
@jeffostroff
@jeffostroff Жыл бұрын
Glad it helped!
@jeffhitchcock3368
@jeffhitchcock3368 4 жыл бұрын
Very helpful. I was able to TS the issue and found the heating element to be “open”. Thanks!
@jeffostroff
@jeffostroff 4 жыл бұрын
Great to hear! Did you replace it and get it working again?
@jeffhitchcock3368
@jeffhitchcock3368 4 жыл бұрын
jeffostroff part is coming in from Amazon sometime today.
@RAWRdc2
@RAWRdc2 4 жыл бұрын
@@jeffostroff 0Ip
@paularroyos2440
@paularroyos2440 3 жыл бұрын
@@jeffostroff w57
@whitieford_rc948
@whitieford_rc948 3 жыл бұрын
I worked on a bunch of these and almost evertime the issue ended up being in the board after replacing the element and the thing sky rockets up over 500 degrees when you start it 😳
@lynseyc4513
@lynseyc4513 4 жыл бұрын
Looks like I’ll be replacing mine again it was just replaced last year. Samsung needs to do something about this.
@jeffostroff
@jeffostroff 4 жыл бұрын
A lot of time people blame their dryer. Mine was my fault because I did not vacuum out the vent ducts leading up to the roof, so it clogged, and super hot moist air remains in the dryer instead of blowing out the roof.
@jackskelly6473
@jackskelly6473 4 жыл бұрын
Same. I replaced mine after 4 years of use. The new one from Amazon lasted 1 year. Fixing it again tomorrow. I take out the drum though. Easy to do and makes it so much easier.
@ntekampe
@ntekampe 4 жыл бұрын
Not all heroes wear capes... that's all I have to say. Thank you 1000x
@jeffostroff
@jeffostroff 4 жыл бұрын
Thanks Nicholas!
@jerrymontes9995
@jerrymontes9995 2 жыл бұрын
Definitely the best you tube to change your element. Down to the “tee”. I would advise anyone to watch this if your Samsung dryer is not drying. You the man.
@jeffostroff
@jeffostroff 2 жыл бұрын
Thanks so much Jerry!
@tubethis777
@tubethis777 2 жыл бұрын
After searching on multiple channels, your comments, safety tips and filming were on point, thanks a bunch, best of kind.
@jeffostroff
@jeffostroff 2 жыл бұрын
Awesome, thank you!
@wlfe-cs5rb
@wlfe-cs5rb 4 жыл бұрын
Perfect! Saved me tons of time man
@jeffostroff
@jeffostroff 4 жыл бұрын
Glad it helped!
@shipasailproductions5067
@shipasailproductions5067 2 жыл бұрын
Thank you so much for sharing this. I paid $17 and bought the heating element, followed your video to the letter and now my dryer is working better than before. You literally saved me hundreds of dollars.
@jeffostroff
@jeffostroff 2 жыл бұрын
Glad it helped! Cha ching!
@lorenziovelasquez5501
@lorenziovelasquez5501 3 жыл бұрын
A MILLION THANK YOUS !!! Today I got to fix my dryer and my mom couldn’t be any more happier !!! Thank you so much !!!!!!!!!
@jeffostroff
@jeffostroff 3 жыл бұрын
Glad to help Lorenzio and thanks for watching.
@TortillaTheHun151
@TortillaTheHun151 6 ай бұрын
This video along with the recommendations saved me from wasting money on buying a new dryer. Every penny counts and spending the money on this kit helped save me money for another project. Thank you!
@karenh7369
@karenh7369 2 жыл бұрын
You are awesome! I watched other videos to fix my dryer and those showed taking the dryer apart !! Jeepers!!! I’m a subscriber of your channel since the FL condo collapse so when I saw this video, it was the ticket! Did myself (help with my 78 yr old Mom too) and I DID IT!!!! I snapped off a connector on the thermistor thing and bought new one but I felt like a pro. Dryer working great!!! Thank you for taking the time to upload this video.
@jeffostroff
@jeffostroff 2 жыл бұрын
Glad to hear you made that repair yourself Karen!
@jessipufahl1252
@jessipufahl1252 2 ай бұрын
Well, well, well. I thought that I would be the only old lady here, watching videos on how to replace my heater element. Thanks so much!!!! I did it all by myself!
@jamesgking1384
@jamesgking1384 Жыл бұрын
Truth be told there is to many people trying to do this DIY videos. I think most do it for money or whatever. I want to say that this guy "first video" does way better at explaining everything to do a really job!!! Probably the best I've ever watched. He gives information that can save lives as well. Thank you sir, I think I'll follow your efforts in life. Great job, I will be watching move of what you do and I'm sure learning somethings most overlooked. Dryer fires should never be overlooked!!!
@flubu33
@flubu33 Жыл бұрын
This was simply one of the best videos I have viewed, it was correct in the cause, used the link to order the part and once the part arrived, had it all put back together and operational within 1.5 hours. I can not thank you enough for the assist, subscribed, liked and passed this on to my friends.
@annikfarley5545
@annikfarley5545 Жыл бұрын
This video may be 3yrs old… BUT it has blessed me a mother/teacher to fix my dryer and save a great deal of money. Thank you sir for the very informative DIY video!
@RRivera-tn3jz
@RRivera-tn3jz Жыл бұрын
Jeff, hello and how are you? It's Ruben from the big M. I needed to repair my Samsung Dryer and low and behold... your still doing this stuff and let me say your video saved my ass. Thanks a bunch and keep up the great work. Peace.
@jeffostroff
@jeffostroff Жыл бұрын
Awesome Ruben, thanks for watching and glad it helped!
@EmjayG129
@EmjayG129 2 жыл бұрын
This worked perfectly! My husband and I just finished repairing the dryer and what a joy it was to turn it on and get heat! We used the link you provided to purchase the heating element gathered up all the tools required and set to work. By far the most difficult part was getting the screws out of the back part of the heating element then putting them back in...more awkward than difficult. You saved us a hefty repair bill as quotes ranged from $220.00 ca to over $300.00 ca. Thanks Jeff!
@jeffostroff
@jeffostroff 2 жыл бұрын
Way to go Glad it worked!
@24SE7ENN
@24SE7ENN 4 ай бұрын
Also one of the many who is beyond grateful for your expertise! This has saved me a bunch! Extremely informative, detailed, and easy to follow! Thank you, Thank you, THANK YOU!
@bradox296
@bradox296 Жыл бұрын
Great video. Couldn't have done this with any degree of confidence without it. The heating element looked almost exactly like the one you pulled out in this video, though not as black. What was even better than the video was the link to purchase just the coil and sensors. I was about to drop over $100 on the entire assembly, but the coil itself with sensors was only $30. Thank you so so much!
@jeffostroff
@jeffostroff Жыл бұрын
Glad to help Brad, and yes that kit is a lifesaver of savings
@torcan1990
@torcan1990 3 жыл бұрын
Thank you so much for patiently providing us step by step instructions on how to fix the dryer heating problem. Your steps were so easy to understand and I was able to fix my dryer, without having to go out and buy a new one.
@jeffostroff
@jeffostroff 3 жыл бұрын
Great to hear Rosshan!
@lowbar913
@lowbar913 2 жыл бұрын
Just completed this fix on my D42H5000. It took me about 2 hours but I'm the least handy person ever. Thank you Jeff, money is real tight for me these days and your video gave me the confidence to try to tackle this myself. With the money I saved I'll be able to afford several more months of the medicines I need. Your content is a literal livesaver. I can't thank you enough.
@jeffostroff
@jeffostroff 2 жыл бұрын
Thanks, I'm glad you liked it!
@3811eric
@3811eric 2 жыл бұрын
Thank you for the video tutorial! My Samsung dryer had no problem for over 17 years; I've had GE, Maytag, Speed Queen before and never lasted 2 years. All I do is just regular vent cleaning and my Samsung dryer runs like a new one every year and every time. Cheers!!
@jeffostroff
@jeffostroff 2 жыл бұрын
Great to hear!
@stickmanutilities
@stickmanutilities 7 ай бұрын
Best Video ever to fix the problem. Followed it excatly and fixed my dryer issue. It was the heater core. It blew apart about where you showered yours. Got the part from Amazon. $30 and I replaced all the thermostat and core all together. This video really helped me thanks. In a hour or so it's working line new.
@jeffostroff
@jeffostroff 7 ай бұрын
Yup, I just had to do this dryer again last month, the heater core this time had only lasted 1 1/2 years
@stickmanutilities
@stickmanutilities 6 ай бұрын
@jeffostroff I have had this dryer right at 4 years. It stopped making heat. I youtube the problem. Saw your video and tearing it apart. Sure enough it was the heater core
@najibmorocco6002
@najibmorocco6002 8 ай бұрын
Thank you so much for your time and effort. You,ve just save me from a big bill. Great video, i followed you step by step, all was clear. Under $40, and less than 2 hours I fixed my Samsung dryer. First time I fixed an appliance by my self. Great thanks.
@prashanthurrynag3776
@prashanthurrynag3776 Жыл бұрын
I have a Kenmore dryer, which is made by Samsung and this tutorial was amazingly helpful😊. Thank you so much, you saved me a ton of money !
@jeffreygolden2629
@jeffreygolden2629 2 ай бұрын
4.5 years later and a different Samsung dryer, but your walkthrough just helped me replace the coil. Thank you so much!
@WilliamShick
@WilliamShick 2 жыл бұрын
Jeff!!!! Dude!!! That video was spot on accurate. I watched it twice, took notes the second time so i had a batter idea of what to expect. I vacuumed everything out and took a picture like you suggested of the wires. My model was slightly different than yours. There were three screws along the top front panel. Mainly the Heater element bracket only had two screws in front and had two bent rear tabs down thru the bottom panel. You tip it up and pull out forward to remove that bracket. 'Twas a much better design than the two blind screws. The coil leads were OPEN. The thermistor and thermostat measured correctly. The coil was open on the underside in the same area as yours. Now I will order the replacement and reassemble. I am confident it will be fine afterwards. Thank you again for your awesome video. God bless!!!
@jeffostroff
@jeffostroff 2 жыл бұрын
Glad it worked William
@mr.justice3220
@mr.justice3220 2 жыл бұрын
I truly wonder how many people you’ve gotten out of this situation through your video. Thank you for the detailed look and info! Mine had overheated and cracked without any lint in the machine or exhaust.
@jeffostroff
@jeffostroff 2 жыл бұрын
I get about 5 people every day who comment how this video helped them, glad I uploaded it
@breannarichardson4867
@breannarichardson4867 Жыл бұрын
Maaan! This video helped me fix my dryer! You are a great teacher! After watching your video I feel more confident in fixing other things around my house. You rock sir!!
@jeffostroff
@jeffostroff Жыл бұрын
Great to hear!
@jamesdodge1733
@jamesdodge1733 Жыл бұрын
Thank you for this video. I purchased the entire unit instead of replacing just the heating element. I was able to take apart and replace it and put it back together with in two hours. Your video so SUPER helpful. Thank you.
@jeffostroff
@jeffostroff Жыл бұрын
Great job James!
@jimderk2112
@jimderk2112 3 жыл бұрын
Thank you, one of the best how to videos I've seen on utube. Samsung certainly could have made life a little easier with a little bit more thought in their design. I'm glad I found your video.
@jeffostroff
@jeffostroff 3 жыл бұрын
Great to hear Jim!
@garthdebevoise8287
@garthdebevoise8287 2 жыл бұрын
Wife thinks I’m a hero. Thanks Jeff. I’m pretty good mechanically but if you’ve never done it this is an awesome step by step description. Thanks again!
@AMM0beatz
@AMM0beatz 2 ай бұрын
I have the same exact problem with my dryer! Let me tell you, I’ve seen a ton of dyi break-fix videos and this by far is the bestI’ve seen. Sir, thank you! Getting the part now!
@elizabethjoyce7817
@elizabethjoyce7817 2 жыл бұрын
THANK YOU!!!!! You made replacing the heating element SO EASY. I got it repaired in about 2 hours, and that includes picking up the part. GOOD NEWS: I have a newer Samsung Steam Dryer and the metal platform that the element casing sits on does not have that back screw!! It has 2 slots that you just slide the back side into! Easy peasy!
@donaldthompson5463
@donaldthompson5463 3 жыл бұрын
Best instructional video I've ever seen me and my wife were able to fix my dryer you left nothing to question thank you
@jeffostroff
@jeffostroff 3 жыл бұрын
Great to hear Donald
@theSEAacademy
@theSEAacademy 2 жыл бұрын
You da man Jeff!!! Just did this dryer fix for $25!! Your video was detailed, full of personality and perfect for this fix!! Thanks so much my man!!
@jeffostroff
@jeffostroff 2 жыл бұрын
Thanks, I'm glad you liked it!
@theSEAacademy
@theSEAacademy 2 жыл бұрын
@@jeffostroff Help Jeff! First time drying, heard a pop and now it's running cold again? Bad element?? I know I went exactly by your directions!? Haven't opened it up yet to look at the element.
@ZZAAAID2
@ZZAAAID2 2 жыл бұрын
What sets this video apart from others is the importance of checking electrical continuity of various components involved, not just the heating element. This way you can diagnose the actual problem. Last year I replaced the heating element using this video. This year the heating element has no problem, but the thermal fuse is the culprit. Thanks a lot!
@saroumath6041
@saroumath6041 2 жыл бұрын
The cheap heating element is probably the problem that I’d blowing out the fuse.
@JaiTheFaeBae
@JaiTheFaeBae Жыл бұрын
Repair techs were telling me $150 to $500 but we can't tell you an exact price until we come out which will cost $100 😫 Just repaired the dryer myself for about $30! You're out here doing the Lord's work 😆👍🏽 Thanks!!!
@raphaelguay141
@raphaelguay141 2 жыл бұрын
Thank you so much! I was able to repair my 10-year old dryer for 40$! Very informative video and I am immensely grateful for your expertise.
@jeffostroff
@jeffostroff 2 жыл бұрын
Awesome Raphael
@seancusson72
@seancusson72 2 жыл бұрын
You just saved me so much money in terms of bringing someone in to fix our Samsung dryer which is now 13 years old. Thanks so much for making this available,.
@jeffostroff
@jeffostroff 2 жыл бұрын
Thanks, I'm glad you liked it!
@shangoshots
@shangoshots Жыл бұрын
Thankyou for the Details,(step by step) procedure. Very useful and Great success to you.👍🙏💯
@jeffostroff
@jeffostroff Жыл бұрын
Thanks, I'm glad you liked it!
@sadgi3
@sadgi3 3 жыл бұрын
You rock!!! This video saved me $500 in calling a professional!! Thank you so much, very informative and easily to follow! Keep up the great work!!!
@jeffostroff
@jeffostroff 3 жыл бұрын
You're welcome!
@jaysmith6013
@jaysmith6013 5 ай бұрын
This happened at my parents house, so naturally they started shopping for a new dryer! I went there and took a look, sure enough I saw the dryer duct was completely clogged with lint, about 5 years worth. I kid you not, I filled up over half a garbage bag worth of lint. After that, used this video and a few others to replace the heating element and viola! Not only is the dryer working, it’s drying the clothes much quicker than ever before. Thank you!
@debbieli9596
@debbieli9596 3 жыл бұрын
Thank thank thank you!!! None of the other videos showed this exact model! I really appreciate you making this video! It was so easy to fix!
@jeffostroff
@jeffostroff 3 жыл бұрын
Glad I could help Debbie
@mattyouell1611
@mattyouell1611 2 жыл бұрын
Thank you! The whole family has been down with the 'rona for the last few days and the dryer stopped heating. In addition to being sick we have a special-needs kid which means that laundry never stops in our house. Wife was stressing. Can't exactly ask someone to do a service call with a house full of contagious folks. I'm fairly handy but wouldn't have figured out how to approach this repair without your video. Despite being sore all over and semi-feverish I was able to get this thing back up and running in about 24hr, including getting the parts from Amazon. My model (DV210AEW) had a slight difference in the mounting bracket. Instead of two screws in the back, it's two tabs in slots in the bottom of the unit. I was excited at first because I thought I got off easy. Nope. Finally figured out that I had to tilt the dryer up a bit to pry those tabs loose from underneath. I think you're supposed to be able to rock the bracket out but there wasn't enough clearance. I tend to hold mechanical engineers in high esteem, but I must say they could have designed this unit to be a lot simpler to repair. Thanks again.
@davemoriset
@davemoriset Жыл бұрын
Honestly 1 of the best DIY vid on KZbin step by step instructions couldn't f it up even if you try!!!!! 👍🏿👍🏿
@alexanderaxt7522
@alexanderaxt7522 3 жыл бұрын
Thank you for this video! Was able to fix my Samsung dryer in 1 1/2 hours following your video and all for a $30 part. Really appreciate your thoroughness!
@jeffostroff
@jeffostroff 3 жыл бұрын
Way to go Alexander glad to hear you were successful and thanks for watching my video
@fusihohairs179
@fusihohairs179 2 жыл бұрын
My husband suggested we buy another Dryer Machine but I came across this video. Thanks to this video that I was able to fix the issue. But now it’s squeaking. Maybe I need to make some adjustments. Good thing it’s drying now! I rarely even take the time to “Like” and “Comment” on a video. But I had to with this video. Thank you!!!
@marceloarreola2663
@marceloarreola2663 Жыл бұрын
Jeff - You are the man! I was able to replace my heater element within a few days going out and it was as easy as you made it look. God bless you, sir!
@samanthagunn4988
@samanthagunn4988 2 жыл бұрын
I am so thankful for this step by step video. I AM SURE YOUVE saved us a ton of money.. I fixed the dryer all by myself.. Feeling so proud
@jeffostroff
@jeffostroff 2 жыл бұрын
Awesome and yes I have kept many many people from spending 3 or $400 on the repair person
@JC-xg2ic
@JC-xg2ic Жыл бұрын
Thanks so much for this detailed video! Even though I was looking for an excuse to get rid of the Samsung appliances that came with the house, figured I could try to fix it first to at least finish my laundry. But omg, the lint dust! I vacuumed out the vent in the wall first with my shopvac and it clogged for a sec with the chunks that came out! Glad I watched this video and saved myself a fire. My parents never owned a house, so I had no idea that it was a thing to be aware of. The only thing I wished the video had addressed was how tricky the metal wire connecter tab things connected to the shell of the heating element could be. I figured it out eventually! Thanks again!
@jsvanaul
@jsvanaul 9 ай бұрын
Jeff, thanks for this video. Very clear and concise directions. This video helped me a year ago with my in-laws' dryer and now I was able to reference it again for my own.
@jeffostroff
@jeffostroff 9 ай бұрын
I'm so glad the video was helpful to you not once, but twice!
@chefhenrywhatsinyourfridge9325
@chefhenrywhatsinyourfridge9325 Жыл бұрын
Did this with my husband now we feel like we can conquer the world. Thank you so much!!! Saved us lots of money
@SusieC10
@SusieC10 3 жыл бұрын
THANK YOU 🙏🏼 so much, I have the same red Samsung dryer as in this video. We were able to repair it ourselves and saved a ton of money. I watched your video and was able to instruct my husband with every step. Thank you again. 👍🏼
@lorileetaylor7730
@lorileetaylor7730 2 жыл бұрын
I agree wholeheartedly with the previous commenters, Your video was so easy to watch and You Sir are a Saint!!!
@jeffostroff
@jeffostroff 2 жыл бұрын
I appreciate that! thanks Lorilee
Troubleshooting And Fixing A Samsung Dryer That Is Not Heating!
19:26
DuctTape Mechanic
Рет қаралды 26 М.
Мен атып көрмегенмін ! | Qalam | 5 серия
25:41
“Don’t stop the chances.”
00:44
ISSEI / いっせい
Рет қаралды 62 МЛН
90% of Toilets Are Installed Wrong (Here’s the Right Way)
16:04
Home RenoVision DIY
Рет қаралды 2,1 МЛН
Samsung dryer not heating? Test these 5 things first!
4:53
Parts Dr
Рет қаралды 160 М.
Humidifiers: Simpler is better?
28:34
Technology Connections
Рет қаралды 2,6 МЛН
How To Fix a Dryer Not Heating (Quick & Easy)
4:55
Appliance Factory & Mattress Kingdom
Рет қаралды 343 М.
Are Heat Pump Dryers Really Worth It? Miele Dryer Review
13:11
Undecided with Matt Ferrell
Рет қаралды 789 М.
Unfiltered 100% Waste Oil Vs Stock Diesel Heater
19:38
SteinFab Garage
Рет қаралды 533 М.
How To: Samsung Dryer Heating Element DC47-00019A
14:10
AppliancePartsPros
Рет қаралды 1 МЛН
THIS is Why Your Heat Bill is So High
18:21
Home RenoVision DIY
Рет қаралды 1,6 МЛН
Dryer Troubleshooting - Top 10 Dryer Problems
36:31
Word of Advice TV
Рет қаралды 317 М.
How to SUPER CLEAN Your Dryer and Dryer Vents!
26:59
The Fixer
Рет қаралды 1,1 МЛН