DSC Power Series User Code Programming - Alarm System Store

[@PCman50]

Alarm Systems Store is an excellent source for an alarm system. They supplied me excellent support with my purchase of a DSC power series alarm system. 👍

[@AlarmSystemStore]

Thank you for your business!

[@dondonaldson1684]

Excellent, straight forward tutorial. My Power 1832 was a snap to program following your simple guide. I also highly recommend a PK5500 full message keypad! Makes it easier for less experienced installers/users.

[@kenzoezequiel9525]

i dont mean to be off topic but does any of you know of a way to log back into an Instagram account? I stupidly forgot the password. I appreciate any tricks you can offer me!

[@fabianmalcolm6511]

@Kenzo Ezequiel instablaster ;)

[@kenzoezequiel9525]

@Fabian Malcolm thanks so much for your reply. I got to the site on google and I'm waiting for the hacking stuff atm. Seems to take a while so I will reply here later when my account password hopefully is recovered.

[@kenzoezequiel9525]

@Fabian Malcolm it worked and I finally got access to my account again. I'm so happy! Thank you so much, you saved my ass :D

[@fabianmalcolm6511]

@Kenzo Ezequiel no problem =)

[@DF-zo7qv]

I've purchased a property that has a DSC alarm with keypad PK5508 installed. I have no user instructions or manual. Anyone know how I can get one?

[@pinakipm]

Some how the panel does not show enter section screen rather it shows zone definitions. How can I change to section driven screen

[@anthonyhinskon2835]

How to program dress code on 1864 panel

[@sddc7972]

I have the 1864. It's already programmed and the zones are labeled. However, I want to change partition 1 , partition 2 etc to actual room names. How do I do so? Thanks

[@AlarmSystemStore]

Partitions actually separate the system into separately armed sections of the system, its not just a labeling setup. If you partitioned your system you would have to arm every "room" separately which would become very tedious. I also do not believe you can label partitions on the older system, but its discontinued so its been a good while since we've worked with one.

[@straighttothepoint364]

How do I reprogram after canceling our monitor service to stop sending signals to avoide the error code 4 ? We have the wifi connection. The person keeps saying we need a service call or get monitoring again. Can I just disconnect the communication wire?

[@chrisorr4087]

I factory reset my 1666, it says program but won't do anything when I type *8

[@frankbear6354]

Can I use a HS2LCDRF9 keypad I have left over from a DSC Powerseries NEO install on a NON neo Powerseries setup with another customer?

[@AlarmSystemStore]

No, incompatible.

[@DiyintheGhetto]

Hello so what happens if you bought a house with this setup and the master code and others codes are not default and changed is there a way to restore everything to original default?

[@dondonaldson1684]

Go to your main board, unplug the battery (observe polarity for reconnecting), unplug your transformer, add a short wire from "PGM1" to "Z1" (we temporarily remove any zone 1 wire), plug the transformer back in for 10 seconds, then remove the insulation and jumper wire, reinstall the zone 1 wire, replace the battery and the defaults should be restored. CAUTION, this removes all zone programming attributes/definitions so you will have to reprogram them along with new master code, installer code and any user codes you may wish to have.

[@willdogs4286]

You can check the installer and master code by entering their respective section. The numbers on the top line will indicate the numbers in binary. You scroll through using the arrow keys. For example, in Section 006 the default installers code will show the 1 and 3. For the master code it will show 1, then 2, then 1 & 2, then 3 corresponding to 1-2-3-4 as the default.

[@Moe2907]

Hello, I changed battery on my 1864 now getting Gen sys sup error message. I tried resetting it but keypad is still prompting me for installers code....what can I do?

[@jagjitkang1227]

Green light not working

[@helpthehurtlondon]

Kinda strange it doesn’t ask you to confirm the new code. That would be a good failsafe so that you don’t inadvertently lock yourself out

[@christinesonevski387]

How do you reprogram zones?

[@synoptik1800]

That's what's need to know as well.

[@alaaalabdali7133]

Tack

[@puretoronto]

Thanks.

[@ВячеславОрлов-и9и]

Научитесь пользователь Клавой

[@stevehagens1941]

Tball chaos

[@philmorrison4320]

waste of precious time by listening to worthless dribble. trying to drag this video out 10 linger than necessary?