Removing The Engine on my Mitsubishi Evolution

The Drop is live! » vasyn.com «
Parts Needed for Blend Door Issue:
Blend Door: 7801A360
Cable: MR979515
Gears: 7801A110
Filter: MN185231
• Links to Where I Purchase Parts:
eBay: goo.gl/LwmuxE\
As an eBay Partner, I may be compensated if you make a purchase
Amazon: amzn.to/2z6hMbF
• Camera Equipment I Use:
Main Camera: amzn.to/2W2ZLId
Backup Camera: amzn.to/3gMgjwj
Go Pro: amzn.to/31Yi59n
Main Lens: amzn.to/2ZX7ZTB
Backup Lens: amzn.to/2W2OgAM
Photo Lens: amzn.to/2O8sc35
Microphone: amzn.to/31ZRDfo
Drone: amzn.to/3iMOIwJ
Gimbal: amzn.to/321daUZ
• Instagram: / dvniemela
• Facebook: / dvniemela
• Sponsors: (Discount Codes)
avalonking.com/ref/dvniemela (DEVIN25)
SK Tools: bit.ly/3mdXhSl (DVNIEMELA)
IAA: bit.ly/3cMmRKk (DEVIN23)
www.braumracing.com (DVNIEMELA)
www.prismaticpowders.com

[@Dhane-0]

Evo: belt squeaks Devin: I’ve slept on it and decided to pull the motor

[@mfdavisca]

Hey Devin, it would be awesome if you raffled off a tour of your shop/ a day to hang out, get coffee from the stand then work on a project you are on. Thanks for all that you do!

[@Fox92Rider]

To be honest from my experience with evo’s I always wondered the same thing with the rattle noise coming from the bottom of the car looked over multiple times could never figure it out until I switched over to the exedy twin disk with Oem flywheel not talking bad on ACT clutches cause I still rock with them until this day on other builds just thought I would let you know what worked out for me and had luck with Man every time I watch you’re videos makes me miss my yellow 8 worked super hard when I was 18 to make it a goal of mine to own one and it had to be yellow but yea I hope that helps.keep up the awesome content you’re killing it hard work really pays off much love from Colorado 💯👊🏽

[@michaelhaffner9986]

Being a mechanic for several years, I know that the symptoms you describe (rattle goes away when clutch pedal is pushed in) about the rattling are the cause of a bad throw out bearing. I'm assuming you have a brand new OEM throw out bearing, maybe you need a stringer aftermarket one due to the strong twin disc clutch?

[@JonHop1]

Mine would rattle no matter what on my dc5. Tried many different aftermarket ones. Once a went with a Tilton hydraulic setup, which is super sturdy, never heard it again.

[@bryanrose20]

My throw out bearing is bad and it’s a constant rattle unless the clutch is depressed. His is just on decel. Maybe it is the throw out bearing just starting to go bad?

[@monstershayne]

And only happens in certain gear(s)?

[@JonHop1]

@@monstershayne Could be his input shaft too... A lot of old manual transmissions are noisy.

[@joemaggio6806]

@@JonHop1yeah I say input shaft bearing or some other bearing I don’t know the name of around there

[@13sky19]

Great job Devin! I always enjoy the vids! Just copped some apparel!

[@Wekeslayer]

As a evo 9 owner, I love watching Devins vids. Very educational vids, thank u Devin

[@lcameeno1]

Ok

[@Wekeslayer]

@@lcameeno1you must be one of those tree hugging hippies 😂😂😂

[@lcameeno1]

@@Wekeslayer ok

[@graemewhitfield2940]

Been fitting exedy twin plate clutches for a few years. Yes they rattle when the pedal is pressed but it’s a fit and forget clutch.

[@Jdm2005sti]

Nice work on the controls for heat control. 🎉 I’m celebrating my man always great stuff and sharing knowledge. I too struggle with the modifications on car debate often ask yourself is the clutch sound bearable or unbearable. You’ll figure it out brother 🔥🔥🔥

[@firebladelover7]

When you come to re-fitting the head gasket, check that the head dowls aren't stopping the head fully seating. I've know this to be an issue on rebuilds before. Rare but worth a check!.

[@louiscongionti2394]

I think not having the balance shaft makes that noise that you have worse . I left mine in the motor cause i did not want the vibration cause it tends to loosen things up in the engine bay.

[@kyleturk6579]

I have normal chatter on my exedy twin disk on my 9. When it gets warm it’s less noticeable.

[@keech25h]

You shouldn’t need a kiggly trigger to run a haltech. I still run the oem trigger plate and sensor with an elite 2500

[@tomswindler64]

Very nice,good progress 😎😎😎👍👍👍

[@MaxiMejia-vb7vv]

Amigo amó todos tus videos onque no sé nada de inglés te sigo desde hace 5años eres el mejor 👌

[@cloudgaming3043]

If i missed this my bad but are you running a lightened flywheel? If so move to an oe or heavier fw and that should get rid of the chatter on decel

[@EvoMakennaS]

Love the hard work

[@BNR_248]

Mates evo 6 did it as well, the noise was a bit worse though. My old evo 7 was fine though on a single plate exedy (AU not JPN) heavy duty clutch. Won't be good enough for your build though. Can also try OEM Flywheel, i know R34 GTRs have decel noise with an aftermarket dual mass flywheel/clutch combo. Goes away with an OEM flywheel while still retaining the high hp clutch.

[@DevinGT350R]

My quartermaster twin made a similar sound, although there was a lot of other sounds and vibrations so hard to pinpoint what was actually from the clutch.

[@Anfurnyy]

I don’t have an 8 or 9 but I’ll chime in since it’s related. I’m running a act 2900 kit on my 1g making 750+whp and 600ft/lbs and it’s holding just fine. Not sure that twin disk is REQUIRED for what you wanna make.

[@funnycartube]

My 2005 Mitsubishi Lancer wagon, non evo, has cabin filter in the glove box, and everything spins freely and like brand new.

[@mfdavisca]

Same sound Devin. Evo 9, loud clutch chatter on deceleration.

[@jclc4201]

The upload today is early. Lets go.....💯💢💥👌💪

[@LaStanley]

Run an exedy twin plate on my evo 7 and it only rattles when you push the clutch in not when its out, pull type clutch, hope this helps mate 🤙

[@dankimir8593]

Have you checked the serpentine idler and tensioner pulley bearings for play? I had a decel rattle noise in an 8 and it turned out to be the tensioner bearing.

[@mityadriveofficial]

I advised U to paint main gasket with special copper paint for gaskets when u start to assemble engine. I dont know if u saw my comment.

[@JoeyLace193]

I've got a ND unsprung triple plate clutch in my 8, that's a noisy thing. Rattles somewhat when the clutch isn't pressed in. Then makes a horrendous noise when clutch is depressed. Just got to live with it if you want a high HP evo

[@AWD_T]

Uniclutch claims no rattle, holds all the power and feels like oe pp

[@483SGT]

I love oe pp

[@user-bl6ed1dq8w]

Got one in my boosted g37 and it’s very nice just bites very high in the pedal and has held up to the abuse

[@joemaggio6806]

I have the same kind of thing just on decel in my 07 civic si with the act hd street clutch. She hooks pretty good. Almost feels like that’s all the car wants to do

[@andrewdero6271]

It is still best to use oem clutch. But some aftermarket ones got some glitch too some needed to be grind

[@MreignSupreme]

I used to own an 8 and it did the same rattle noise on decel although it was only noticeable in 3rd gear for the most part

[@kevinstier4953]

I wonder over time if the heat is what causes the blend door to get hard move because it's made of plastic.

[@Nikeguy230]

Man you guys should’ve made more skate decks!!!😤

[@khazi.4g63]

i have a fully built 8, i dont have that noise youre experiencing, im running an exedy twin disk

[@cloudgaming3043]

ACT clutches tend to chatter on decel. Well known and documented issue they just wont fix.

[@Steve84902]

Twin plates are noisy mate but they hold good power. My mates in the same too

[@joelh3364]

Always educational. My 8 only had a single plate ACT, so I'm thinking the sound may be normal for dual/triple ?

[@cloudgaming3043]

Naw it’s pretty normal on ACT clutch kits especially when paired with lightened flywheels. Just fyi

[@Ebokevo]

I have a fully built evo and i put a exedy twin disk and it makes no sounds shes mint

[@JonHop1]

Is it the TOB? I had a similar sound from tiny play in the bearing. I went to a Tilton hydraulic TOB and never heard the sound again.

[@sk8mike_1]

I have a 8 with a "stage 3" competition clutch and mine does it but it is not loud at all. You can hear it for sure with no music or anything but it is faint for me.

[@nickdoescher9957]

Isn’t the balance shaft deleted in this engine? Wouldn’t that get rid of your vibration from the clutch and isn’t that what it’s used for.

[@boosthead90]

Bump for evo 👌

[@sf2372]

Was the first mod on my Evo 8 adding a cabin filter.... all those years ago now.

[@DumbTheories]

My built to the hilt evo 8 had a exedy triple and sounded like that, prob a bit louder even. It is what is is lol

[@maxcotter1905]

Yes my clutch master twin disc makes the same noise evo 8.

[@itsvitex]

Dont quote me on this, but could that clutch noise be louder because you didnt put the firewall padding back on?

[@Dalekennth1969]

Hello will you be abel to put filter in with out taking it all apart again

[@Ryan_1997]

Lmk if you decide to sell it. Buddy of mine has this same model evo and color. Been wanting evo since they came out.

[@tonytony3577]

Exedy twin disk . You used to install them before.

[@Yamaharidr310]

My 04 was making 800whp with an Exedy Twin and made zero noise on decel.

[@JamesMcMahonAU]

Mine does it and I was hoping you were going to solve the mystery.

[@isayahjimenez5305]

I got sweatshirt and a tee and a banner 😎💪🏽

[@deanoramsay40]

Up bro

[@KeViNMCMXXCIX]

Cool drop! It's commendable how meticulous and thorough you are.

[@jacobflemming5091]

Evo 8 here 550whp with a exedy twin and I don’t have that issue sir!

[@Soulsmoker476]

Exedy hd twin plate on Evo 9 running 700 no noise at all

[@codykounce1097]

Yes my buddys evo 9 makes an absurd amount of noise that sounds like failure of something but turn out to be “normal”

[@sebfullick5011]

I have an Exedy twin disc and does same thing. Normal

[@s4ms0n1t3]

When I had a LWF in my e46 m3 NVH under deceleration was looooud

[@SocalSears]

The exedy twin disc is a lot quieter

[@mitchdilsaver5798]

Quartermaster twin disk with HOB for the win. Trade your rattle for twin disk rattle. Lol

[@carlallen1231]

Maybe the clutch sounds louder than you’ve heard before because you’ve removed the firewall cover in the engine bay

[@CypHill]

Is the deck flat?

[@cmeifucanEVO9]

Yes both of my 9s made the noise. My current 9 is louder than my original 9.

[@RyneDickens]

Mine has an Exedy Twin and it sort of always made noise, I just always assumed that it was the cost of running the aggressive clutches. Cause, race car 😁

[@chivigonx3]

My 05 srt4 has a stage 2 act clutch and it has crazy shutter clutch... it's probably a act clutch issue

[@chrisH94]

Yes sir 8s and 9s all have clutch chatter with upgraded clutches

[@maximilians9643]

i missed what the power goal is?

[@STIStuff]

That decel noise is from lightweight fly.

[@jacobmarty5111]

what if the zink plating messed with the trigger somehow

[@boostgaragebuilt1363]

Yes it is very normal for an act clutch to rattle like that 💪🏽

[@sf2372]

Good time to double check the trueness of the mating surfaces maybe

[@xadoptedbabyx5508]

Damn skate deck is sold out already rip but also good for you brotha

[@Nikeguy230]

They restocked as preorders

[@BYELUCKS]

please make evo skate deck👌🏼👌🏼

[@andyvang6549]

You should put l19 stud on this car

[@chaseMcCoyc]

Evo 8 does the same thing with exedy twin.

[@itskittens]

my old evo had the exact same noise

[@gaberodriguez8435]

Red calipers would fucking kill this build ❤❤

[@user-xf8yr5ot4s]

In out in out in out . That engine has been out more times then a strippers snatch lol . Keep up the good work. Awesome build

[@daneyoung7770]

100% normal. Exedy, ACT, XClutch and Comp all do it.

[@JonHop1]

I think it's the TOB tho not properly holding the clutch in place. When I went with a Hydraulic Tilton tob setup, thing was super quiet.

[@aldolara2815]

Bro you should build a S550 mustang. Something different.

[@xxtimeisthefireinwhichweburnxx]

I wish he would sell us sheets of tiny American quarter sized Vasyn "V" emblems on high quality 3M reflecive paper. (like the high visibility tape on road cones and vests) I think people would set their phones down on a small table or shelf and ninja star their wallets at the phones if he sold those because people love tiny stickers...

[@Zerkkys]

gym vlog when

[@johnjbateman]

Your videos stress me out. I could not keep my cool as much as you do

[@JonBonazza]

I can’t recommend ACT clutches to anyone. Too many issues in my experience.

[@SergantMula]

👍👍👍👍

[@Sizzleracer]

U need more mitsubishi evo stuff so I can buy

[@bigsingle6581]

Definitely unclutch, go with a sport will hold all the power

[@ahallhockey]

Evo 8 with act single. Makes the same noise as yours

Can you make bed spreads too and shower curtains lol jk

[@daytonwells1722]

Got an 03 Evo 8 with built motor and twin disc clutch. It’s always made that exact noise on decel and it has always driven me absolutely nuts. Sounds horrible and anyone who rides with me is like wtf. From everything I read it’s totally normal for the car

[@culpritmedia7026]

Uniclutch, brother. Uniclutch.

[@Itsmeart1988]

It’s louder cus you took off the firewall/bulkhead factory thick sound deadener…….. it’s gon resonate inside louder my guy

[@jonathanklenner2678]

Whats the white stain on the seat belt 😂

[@lancetitus9816]

multi plate clutches are just going to ratlle. its normal.

[@davidviana4277]

sounds like the clutch buzz issues that some s2000s suffer from. Only way to fix it is to replace the clutch

[@jackbuildsit]

Mine makes some noise but not bad (Exedy twin)

[@Martegiani]

I bet that rattle is because ACT uses a lighter flywheel that cannot dampen the motor harmonics enough.

[@husamsalhi6071]

change the flywheel, the rattling will go

[@chrislizotte6603]

Is it possible the zinc coat on the trigger was the problem ?

[@Stockholm727]

Since youre taking and using logos without permission im selling vasyn apparel that i make myself on the side for extra money. Hope you dont mind.

[@bigsingle6581]

* Uniclutch