DX6 vs DX6i

[@eazywisdom5904]

I don’t know why I couldn’t stop watching your vib man . You seem so happy and enthused to talk about this awesome stuff . Good Stuff 👍🏽💯

[@chrisstolle5664]

Thanks man!

[@StefanDembowski]

Good comparison and very helpful for a guy like me who's looking for a first radio. Very appreciated, thanks.

[@johncgibson4720]

Love it. I am sold for DX6 . The last time I had a transmitter, it was 10 years ago. It is a total different world.

[@williamwinn948]

Went with the dx6 as my first real TX and glad I did

[@chrisstolle5664]

Just a note, don't run your DX6 out of batteries. I did last week and now the internal RF module doesn't work. I'm trying to get Horizon to fix it but no reply thus far. Keep tabs on your battery level and you should be fine.

[@williamwinn948]

Thanks for the tip really appreciate it

[@chrisstolle5664]

Update--Horizon did replace the RF module and even the parts on the airframe I lost though it's not their policy to replace lost airframes. They said the RF module went to low power (which means it didn't work). The orange spektrum led in the middle of the transmitter is actually indication of the RF module working correctly. If you ever have problems with binding or transmission, check the orange led to see if it is lit. If it wont light, its off to Horizon.

[@Shadowx011]

Awesome radio. Just got back into flying Copters and Tri-copters and this is the perfect radio for me. I cannot honestly think of any reason why I would need anymore channels anytime soon. Very easy to use radio and feels great. :)

[@chrisstolle5664]

+Shadowx011 I don't often need more than 6 channels and can't often afford to buy the exorbitantly priced 7,8 or 9 channel receivers so I concur with your conclusion. My DX6 gets used quite often.

[@nickc.8814]

Thanks for the comparison! I'm pretty much sold on the DX6 now.

[@chrisstolle5664]

Glad this vid helped in your decision. I'm really getting into the DX6.

[@nickc.8814]

Chris Stolle those 3-position switches were high on my list of priorities in a new transmitter.

[@chrisstolle5664]

Ditto!

[@dryocum]

Thank you Chris! I got my new DX6 last night and was able to bind it to my 120sr and a few other Heli's... Nice radio real easy to use...

[@chrisstolle5664]

Totally agree! Watch your battery life. I ran mine down and the RF module went into a low setting. Had to have it replaced. Other than that, I've had zero problems.

[@LifeofBrian2]

Thank you very much. Very helpful for me.

[@icerook1560]

I went DX6 3Gen for my first non toy grade radio, the size was at first strange but man, it's smooth as butter.

[@chrisstolle5664]

Agree!

[@xvxscarecrow]

Great Video. Looking to get into the hobby and this was on the fence of which to get.

[@TheHobbyDrone]

Excellent review, man. I think I'm going to upgrade to the DX6 from my DX6i, mainly for the voice alerts and built-in telemetry. Plus, for $230 you can get the radio with the AR610 Rx!

[@wmdayman]

Thanks Chris, your info was very help full.

[@chrisstolle5664]

My pleasure William! Glad you liked it.

[@baldrickscunningplan6154]

If you are thinking of buying the DX6, then consider the following:- Range is a little better than Park flyer Radios but i would never use one in an expensive model. You cannot boost the output from 100mw to 200mw like you can with the DX6i. They only work well with Spektrums own Receivers. Other aftermarket Receivers like Orange RX have reduced range. So be prepared to fork out extra cash for Spektrums expensive Receivers. Surrounding WI-FI internet transmissions WILL crash your Aircraft. The Toggle switches have the strength of toothpicks and break off easily. It eats Batteries, so you will need to upgrade the TX pack. I fitted mine with a 2s 1300mah Lipo. Spektrums Receivers do not come with PPM outputs, so not really suitable for FPV. Unless you intend to fit a satellite Receiver like the Lemon RX. Effectively giving you 2 Antennas and PPM output but why should you pay more to make your Radio more reliable?? It should work out of the box for this price. Basically the DX6 is dated DSM2 technology with a DSMX patch in a fancy case. My advice is to pay a little extra and get something better. I wish i had done so. Its too much of a headache figuring out why your model keeps losing signal because you flew 100 feet behind a tree.

[@alankopitko1611]

After 45 years of modleing i have just bought this DX6 fantastic, not sure what im going to do with 40 plus Futaba recievers lol. one down point changing to Spektrum recievers even after cutting the lug off the side of servo lead plugs on the Futaba servos its a very tight fit. Great review.

[@chrisstolle5664]

Ha, I've also cut the lugs off futaba servos to retrofit to spektrum as well! What to do with all those futaba RX? Ebay my friend. 45 years of modeling, I'm sure I could learn plenty from you.

[@alankopitko1611]

Its all different today, before if you could build quick and burn the midnight oil perhaps a model could be built in a week, single chanel radio then 27 mhz.. no servo reversing or end point changing, wings with 1/16th ribs all hand cut then covered with silk stuck on with dope.........and a million more memories and skills that are no longer needed. got my dji 450 flying today, with the naza 2 .... gps its crazy, i remember 1986 puting my first video cam into a plane 8ft wing span, full size vhs camera lol the engine vibration shock the video head to peices, could hardly see an image lol camera weighed 4lb

[@chrisstolle5664]

I've got a DJI F450 as well. I am amazed by the stability of the naza controllers. If you're into FPV, you can get around OSD by using your voice prompts to tell you battery info (using spektrums telemetry system) or timer. I use the voice prompt for timer for EVERY plane and multi rotor I have. Super useful without having to keep peeking at the screen!

[@Newbeflyer]

Both of them still have that plastic scroll roller and it always breaks and it's a real pain to replace it...they should of made it metal (someone did make CNC for a while), but the new DX6 has a better antenna for one as the Dx 6i had that flexible one that gets broken, have a charge port in the back for the Tx battery. Plus other features that are a improvement from the 6i ...I also think it is a lot easier to operate it. Like a Volkswagen ...anyone can drive it. The other thing is those little washers that keep the switches in place always get lose and even lost make sure you tighten them done of use a bit of rubber glue to hold them in place..I like the Dx 6

[@vinnyavalanche]

Love this radio Awesome it is ......this review helped me make my purchase subbed

[@davidferrick]

I would disagree on BEST FEATURE. Best feature is being able to import/export profiles. I am an amateur and programming from scratch was not fun as a novice. Spektrum did a fantastic job of having a ton of profiles for quadcopters from Blade which is what I typically purchase. I download all the profiles for my NanoQX, Blade 180QX, Indunctrix, 200QX, 350QX and Mach 25 and was flying in seconds. It was the #1 reason I upgraded from DX6i to DX6 ... that and I was too lazy to upgrade my screen with a backlight. Having that on the DX6 was a definite plus.

[@marckart66]

DX6i is £110 with receiver here at a local shop, and the DX6 is £150 with receiver in the same shop. I was on a budget since my DX5e broke, but I just went for the DX6 instead.

[@chrisstolle5664]

Good choice. DX6 prices are falling and it is worth the upgrade!

[@sokey70]

I'm just delving in to RC planes and have done ground and water for 15 years. I am going to get a flight sim to start with and move to some foamies as I get a bit of experience with the transmitter. Do you think I should get the Tx I plan to fly with or something cheap to get me by in the sim and a DX6 later when I have a real plane?

[@wlouisharris]

Thanks for the info. I think I am going with the DX6i. I have a DX4E right now that actually works really well. The only issue is the rate switch broke and fell into the transmitter.

[@chrisstolle5664]

+vista7 My trusty DX6i never failed me. Some hot glue or epoxy putty should be able to hold that switch.

[@wlouisharris]

I will surely get one soon. At this point, I can't really justify another 80 bucks for the DX6. It looks like it has a lot of programming options but I'm only flying 3 and 4 channel planes now. I guess if you have quad copters or planes w/ flaps, ect the 6 is better. Actually the DX4E has been solid other than the rate switch which like you say is easily fixable.

[@RCREVIEWS101]

All comes to: DX6i - $90 DX6 -$230.......pick what fits your bill, both will do the job!

[@ipdjbt]

I quickly outgrew my DX6I after only 2 months of use and was shopping for the DX8 when the new DX6 was released. Unless you need the extra 2 channels the DX6 is the clear winner in price over the DX8. Telemetry, 250 model memory, 3 position switches, and a backlight? Yes please! Thanks for the great review!

[@mariogravina4495]

Chris, just got my Dx6, wondering what wind-sensing (hehe) string you have attached to the Dx6 on that video? been looking for something to put there, but cannot find anything that will do. help?

[@chrisstolle5664]

Ha ha, Mario, thanks for the laugh. Needed that today. It is a piece of ribbon I found lying around. Its not the nylon stuff you tie up Christmas presents with. Its made out of some kind of shiny cloth. It works well (much better than the nylon stuff that curls up).

[@mariogravina4495]

Chris Stolle thank you sir!

[@scottfirman]

Ha, ha things have changed huh? Got my DX 6 for $113 lightly used. Apparently, the guy bought it to use in a robotics project. He only eanred it to assign the gimbals to operate some home made electronics thingy, found out it wouldnt work, then sold it on E- Bay. No Receiver, but who cares? It came in the original box, in its original packaging, with everything included thatI needed. There wasnt even anthing programmed into it yet. it was still in Acro mode. Glad you like yours, I still have my 6i. I use it for training only now. Yup, its only a simulator now. sad, sad.

[@jimmyspencer6643]

that horizontal rubber plastic piece is more than a "handle" its a secondary antenna, I would be nice to it.

[@chrisf5475]

So the new handle is an antenna? I was thinking the new stubby antenna would be a bad thing as you shouldn't point it at the aircraft but if it has a horizontal one as well that's great

[@franknapolitano9144]

Without having to manually program, do the switches already have a factory setting for Rates, Flaps, Retracts and Throttle Cut ?

[@MrHyho]

And no annoying beeps on wheel switch turn ;)

[@DonOtterup]

Hey Chris.. :-) Does the ds6 work with ar635..? Is the ds6, for a rc guy who like to program his transmitter all day long, I love to fly, not more programming than necessary. My current transmitter is an old Hitec Optic 6. Im shortly going to invest some money in some new gear. Thanks. Greatings Anders

[@chrisstolle5664]

Hi Anders. The DX6 works with the AR635. I have this rx in my Parkzone Visionaire and works brilliantly with the DX6. Honestly, the DX6 is very easy to program. However, if you want to stick with Hitec, Hitec Aurora 9 and 9x are easier to program as they are touchscreen.

[@geoffadam4475]

Thanks for the review Chris, Does the new Dx6 give you more than 2 mixes ? the Dx6i will only let you do 2 ...

[@stefaroni96]

Turn on time is 3 sec for the dx6i. and 5 sec for the dx6.

[@johncgibson4720]

OK, I just placed the order on amazon. It's black Friday, but no discounts. 199. I also placed order for a nano cps heli, which does have discount.

[@catch262]

If I upgrade from the dx6i to the dx6 will i lose compatability with my blade helecopters? Some of my heles and quads are 180QX, Nano QX, 200 SR with safe, MCPX 2, Nano CPx, 450 3D. All of these are Blade brand. Will the Dx6 fly all of these?

[@chrisstolle5664]

You will not lose compatibility. I have a Blade MQX that works perfectly with the DX6. As long as the heli or quad RX uses DSM2 or DSMX protocol, you'll be golden (and happier with the increased functionality)!

[@scottpizzo5560]

I work at a hobby shop and got an amazing deal($45) on my bosses spare Dx6i and I want to know if you still have to press the roller button near the top on the dx6?

[@AstroBananna]

Awesome, thanks. The dx6 it is.

[@chrisstolle5664]

Glad you found it useful.

[@watchdoggibson]

every one that has done a review on the new dx6 will notice , the software is the same as the dx9 and above , the only differences is the amount of channel's & amount of model's on the older radio's , with the new dx9 and above has the 250 model memory capability.

[@richardcarlin8861]

Other big big problem with DX6i was that to use dual aileron servos the second servo goes into the aux (ie flap) channel so you cant then use the proper flap setup. This is crap if you fly gliders. Is this the same on the DX6? Cheers

[@chrisstolle5664]

Yup, no dual ail, spoilerons or flaperons if you have anything plugged into the gear channel on the DX6i. In the model setup on the DX6, you can set up one or two ailerons for the wing and still get flaps. Channels are all assignable up to 6. One aileron servo or two, one flap or two, flaperons, spoilerons are all possible on the DX6 as long as you stay within the 6 maximum channels. The more I play with the DX6, the more I realize that Horizon should have done all this from the start. I paid the same for the DX6i and the DX6. You get a lot more with the DX6.

[@richardcarlin8861]

Chris Stolle Many thanks. I'm all set to get one now.

[@chrisstolle5664]

I know you'll like it.

[@AndrewsArachnids]

you didnt get ripped off if you got a dx6i + phoenix, the sim is 150$ by itself. at the time that was a good price

[@billyv348]

Hey Chris, Nice video on the two... I have a DX5e (that was my first buy) But I do have a DX6 now that I love and after seeing you vid a few times I'm going to love it more. I have a question about how you set up the ARM button or switch, Can it be the same one for all quads on the DX6? I had a Night Hawk Pro bound to it with the H switch. That was done at the store when I bought both the DX6 and the Night Hawk. It was working fine until I binded with another Quad and it was good but I had not made a profile for that quad nor can i arm it. I'm thinking you first have to make a profile, then bind it and assign a arming switch? The Night Hawk will not arm using the H switch, Do I delet all and start over. Thanks

[@chrisstolle5664]

I assign all my throttle cut to the same switch on all models and my arm switch to the same switch on all multicopters. If you delete, copy your settings to another memory spot. Then when you start over, you can verify that your settings are correct in the new model. Then assign an arm switch or button. Or instead of deleting, just start a new model setup and you can switch back over to see if your settings are correct before deleting.

[@billyv348]

Everything you said in the last reply is good and will remeber it... The real question I was getting at is how or can you walk me though the steps of going in the menu and sub menu as to assigning a switch or button. Is the Throttle cut the same as the Arming switch? I mean when I coneccted the battery to my Night Hawk and switch H was in the away position, it was dis armed and waiting for me to switch it back or to me and then the quad would be in a idle mode, props spinning until I landed and switched it off or away.... Very easy arm and dis-arm... How do I get to that part of the menu to see the options in picking a switch or buton... Thanks so much fo your help.

[@chrisstolle5664]

what flight controller are you using?

[@billyv348]

The quad I had flying off my X6 is a Night Hawk Pro 280. It has Emax BLHeli 4 in1 12A ESC Oneshot supperted (integrated with flight controller) SkyLine32 (based on NAZE32, integrated with ESC's) pre-loaded with baseflight/cleanflight

[@chrisstolle5664]

Go to google chrome store and download cleanflight. Once you hook your FC up to your computer and open cleanflight. You can choose a channel to program a switch onto for arming and disarming.

[@cha3119]

Great review, Chris. This radio can go a long way. When I bought the DX6i I thought no way would I have more than ten plans. Heh, heh - that radio filled up FAST with all the FT designs I built. Here's a couple of bugaboos on the DX6i I hope they addresed: Did they upgrade the rollerbar to metal, not plastic, so it doesn't break? And, did they make it easier to mix elevons, AND not cut the throws in half while doing it. I had to watch about 5 youtube videos how to get this to work when I made the FT Delta. While we're at it, is the manual any better to figure out things like mixing?

[@chrisstolle5664]

Hey Peter, to answer your questions. No the roller bar is still plastic, albeit more substantial to the feel. No longer having to press hard to get a response. It clicks rather easily and is covered in rubber. Elevon mixing is now standard in wing setup. Honestly, the interface is so intuitive, I haven't spent much time in the manual. Though from what I read, I can safely say its easier to follow. Hope this helps.

[@cha3119]

Thanks - I have to stop buying planes and buy the new radio, instead(!) Cheers...

[@chrisstolle5664]

Ha ha! I totally know what you mean!

[@isaiahfurrow7414]

Hey, thanks for the video. I'm just getting back into RCs. My 3 options are to send in my DX6i for repair/refurb. , buy a new DX6i, or buy the DX6. If I get a new radio, I can always send the old one in later and have a backup/trainer/loaner.... any thoughts would be most welcomed....

[@chrisstolle5664]

If you have the expendable money, buy a DX6. It is just so much more. If you're tight on cash, either have your DX6i repaired (or repair it yourself using vids right here on youtube like I've done before) or buy a used DX6i for $100 or less on Ebay. Its really up to you. If you are solely using BNF by Eflite or Parkzone, get a spektrum. If you are a techy guy with expendable money, go for the FrSky Taranis. It takes a lot of programming but is capable of so much and you get to program to your needs. If you have expendable money and dont want to spend endless hours programming but want a ton of options coupled with the easiest programming ever, get a Hitec Aurora 9x. Hope this helps.

[@isaiahfurrow7414]

I'm already pretty invested into DSM2, I've had my DX6i since the very first batch(pre-order)... I've got a decent few Rx already, so my future planes will likely be mostly BNF or PNP from Horizon.... I haven't seen many others that have caught my attention lately other than the Fun Cub. My DX6i needs a new screen without all the scratches, as well as a couple toggle switches and the trim tabs replaced. I've "fixed" the trim tabs before. I think 3 of the 4 so far. They had to be reinforced with paper towel bits and CA.... I'm hoping that the trim tabs have been improved. I'm going to figure out the cost of sending in my DX6i and then go from there, eventually a DX6 is in the works. Thanks again for the input.

[@solsupremo1]

Hi Cris I was wondering if you could help me if is possible I have my spektrum dx6i and I need to install the back light do you think you could do it for me and I’ll pay pay you ???

[@chrisstolle5664]

I could do that for you.

[@fendergrab123]

Thanks for this dude!

[@RCFunTime]

Good review, thanks :)

[@chrisstolle5664]

Glad you found it helpful Michael.

[@dryocum]

Will the dx6 bind with a blade 120 sr heli?

[@chrisstolle5664]

Yes. The blade 120 has a DSM2 rx built in. The DX6 will bind to both DSM2 and DSMX protocol.

[@dannybruno4105]

Can someone help me set up my dx6 with my 200Qx

[@chrisstolle5664]

Hey Spencer, I don't know why youtube wont let me directly reply to you so I have to go this route. I really can't answer that question for you. That decision takes a few variables into account like how much expendable money do you have, how interested are you in flying, etc. Only you can answer those things. If you have the money and the interest, get a DX6. If you are a tech guy, get a FrSky Taranis. If you are testing the waters and want to mess around with a sim to see if you have the bug, then its not a bad idea to go cheap. You can sell it later (albeit for much less than you bought it). If you find that RC aviation isn't for you, then you arent out too much. If you are seriously drawn to RC aviation, get a serious radio. You won't regret it later! Let me know what you come up with!

[@lamjustin9938]

that rubber handle is an antenna

[@chrisstolle5664]

+lam justin Actually it is not. I opened my DX6 to replace a switch I had broken. The rubber handle is just that, a rubber handle. There is no antennae in it. In my opinion, it should have been metal.

[@LIFEOFSTUFFEDANIMALS]

+Chris Stolle Newer versions do.

[@chrisstolle5664]

Curious airlines There is a diversity antennae that sits directly behind the handle and the back. It is a dipole diversity antennae. As far as I know even new versions do not include this dipole inside the rubber handle which would be smart if you drop your tx and break the plastic/ rubber handle off.

[@LIFEOFSTUFFEDANIMALS]

+Chris Stolle Interesting! Yeah I would guess it would be better for durability. Great comparison btw!

[@chrisstolle5664]

My guess as to why they opted for plastic and not metal is possible interference with the dipole diversity antennae. Thanks for watching:)

[@SenseiLeif]

Nice review :)

[@chrisstolle5664]

Thanks Leif. Are you thinking about getting one?

[@SenseiLeif]

Chris Stolle Yes, but store here is still waiting for supply so I might go the 9 instead as it is more fpv future proof with the extra channels :)

[@jonithenjackson5521]

My first Thank U

[@chrisstolle5664]

U bet! Have fun!

[@chowmonkey2002]

Liked your video.

[@chrisstolle5664]

Thank you Sjoerd!

[@stonedboss4765]

"not discussed due to length" its 16 minutes lmao

[@shckltnebay]

Price difference new is $50 don't waste money on 7 year old radio

[@MrJacobbbo2]

Sh*t transmitter. Right out of the box, installed batteries, switched on and I got some weird symbols on the display, and them the transmitter froze. It reset itself, luckily the model was on the ground but I crashed two models with this TX. My guess is that the antenna when pointed directly at the model caused it to loose signal. The switches are BAD! 2 were loose right out of the box and one is damaged. The speaker sounds broken plus it's really quiet when It gives you voice feedback (volume turned up in system setting and the home screen). No vibrator or dual antenna which for the price should be included but oh well. It looks nice, that's about it.

[@chrisstolle5664]

I also had a problem with my DX6. Lost a model. I contacted Horizon and they replaced the faulty RF module and the model. It almost sounds like your problem was the same as mine. I would contact them and tell them all that's happened. They will repair it and possibly replace an airframe. I can totally understand if you are tenative about using it EVER AGAIN because you crashed two models.

[@BMARVOZ]

Chris Stolle So was it a receiver problem or the actual RF module in the transmitter? And does the signal actually drop if you point the antenna at the model? I just ordered one of these... that seems like recall territory

[@chrisstolle5664]

It was the actual RF module. I let the batteries run down. When the transmitter voice warning came on, the RF module went in to low power mode and my parkzone visionaire bit the dust. Horizon replaced the module and my model but I learned to keep a closer watch on battery life. I ran the battery down a couple weeks ago without the same result so must have just been that one RF module. I haven't heard of this happening to anyone else so I haven't heard of any recall talk. But I will take the liberty to warn others to avoid the same problem. I think you'll enjoy your DX6.

[@MrJacobbbo2]

Chris Stolle I sent my dx6 back for service, I got a brand new transmitter, I haven't had time to use it yet but hopefully it's sorted now, horizon was kind enough to back my models to 1gb sd card so that's a freebie at least. Fingers crossed I can be confident with this radio again

[@chrisstolle5664]

After having mine serviced, I havent had an issue with it. Hopefully you'll have the same experience. I was very tenative using it at first but I would say that I've got my confidence back in the transmitter again. Flew with it twice today no glitches.

[@dryocum]

Will the dx6 bind with a blade 120 sr?

[@TheEpiccow400]

Yes