Dynojet Target Tune and Wideband O2 install on my

This is a review of the ‪@DynojetResearch‬ Target Tune with the wideband O2 sensors after installing the Rinehart 2 into 1 exhaust on my Harley-Davidson Heritage 114.
Dynojet Link: alnk.to/9T3XhnA
Checkout ‪@TheHarleyTech‬ and maxwellsmotorcycles.com for parts and accessories.
Also a huge thanks to ‪@KevinBaxter‬ for giving me a little advice and a lot of confidence when it comes to tuning.
Catch me on Social Media:
compiled.social/gearsandgadgets
As an Amazon Associate I earn a small percentage from affiliate links.
My motovlogging Gear and Gadgets:
GoPro Hero5 (Handlebars): amzn.to/3b8poQs
GoPro Hero7 (Helmet): amzn.to/3rjfd0V
Sennheiser MKE-2 Mic: amzn.to/3azVAvH
Tascam DR-10 Audio Recorder: amzn.to/3pf9EyP
Cheaper Audio Setup (I ran for 2 years):
JK MIC-J 055: amzn.to/3oe2SJr (Cheaper audio setup ran for 2 years)
GoPro Mic Adapter: amzn.to/33pTerU (Cheaper audio setup ran for 2 years)
My handheld filming Gear and Gadgets:
GoPro Hero 9: amzn.to/3nHrH0k
GoPro Media Mod: amzn.to/2LhN1v4
Rode Wireless Go: amzn.to/3hGRi7j
Lume Cube Panel GO: amzn.to/3oerJgn
GoPro Max Grip: amzn.to/3ndHcvK
My studio Gear and Gadgets:
Canon T5i: amzn.to/2XcN269
Mackie ProFXv3 Series: amzn.to/3ng7PjA
Rode NT1: amzn.to/396FxDs
Dracast LED500: amzn.to/3ndJGu4
Philips Hue LED Lightstrip: amzn.to/3niybBv
My riding Gear and Gadgets:
Dynojet Black Power Vision Tuner PV-2B: alnk.to/9T3XhnA
Shoei RF1200 Helmet: amzn.to/2KtbFZw
Shoei Transitions Shield CWR-1: amzn.to/2JXUHB4
Cardo Packtalk Bold: amzn.to/2Dkvgnx
FOBO Bike TPMS: amzn.to/34r6ePE
Professionals Choice Low Back Support: amzn.to/3pNZR2T (longer trips)
AirHawk Seat Cushion: amzn.to/2MyPcLi (longer trips)
#harley #dynojet #motorcycles

[@KevinBaxter]

Thanks for the mention...and congrats to you for tackling this and makin it happen. Your honesty regarding experience level is to be commended. All too often I see folks offering advice, basically repeating information they watch or hear from others without any basis or experience of their own by which to support it, yet they position themselves as an expert on the subject. There's an old saying..."When setting out on a journey, do not seek advice from those who have never left home." You nailed this bud...very responsible and honest content. Cheers!

[@dwightbernheimer331]

At almost 80 years old, I've come up with a lot of sayings. I believe the one that would apply here would be... If you throw enough money at a 1958 Ford Edsel, you could make that go quick too... Good stuff thanks for posting...

[@markspaulding443]

Dan I just had installed the same pipes and installed the thunder Max brains to it. Only been a few weeks but a huge difference! Wish I would have known John M was selling the pipes I would’ve ordered from him for sure. Thanks for the video!

[@robertlumsden942]

I installed the SE 131 kit on my 2018 heritage and it is great. you are so right on the hp to weight ratio. much better than a touring bike. i ride very conservative so dont race it. mostly for getting on highway etc. i had my dyno tuned at harley. came out real good. good info on what you did.

[@jasonbreedlove495]

Great video man. It's nice to see the changes and get honest reviews on thr things you've done to yours. Just ordered my PV through Fuelmoto set up with target tune(I had the SE autotuner added with my cam and pipes) as it's time to ditch the EPA tune and really see how my 18 FLHC runs. Keep up the awesome content, m8 heritages are such awesome scoots.

[@JamesSmith-qx2mz]

Very good info, I’m in the same category as you. I’m no mechanic but have tinkered with cars and bikes of all pedigrees since about 1966. I have a 2019 114 Heritage that I installed an S&S 475 cam with S&S cam plate, oil pump, tappets, Fuel Moto push rods. Did the work myself and tuned with the Power Vision tuner. Been debating investing in the Target Tune system and I appreciate your take on the subject. You’re correct about the 114 Heritage, it’s a beast.

[@papap.8006]

Dan loved this video because of the Dynojet info. I had the same setup on my 2018 Fatboy and I loved the info from the small screen. Especially the head temps and all the info it can give you. I plan on adding this to the Tri Glide just to keep a eye on the temperature of the heads. I plan on adding an additional oil cooler and the oil filter relocation to it also. After watching the DK Customs vids I am really concerned with the temps on on the 114 with all the riding I do in hot temps. Just got back from Daytona and did get to meet Baggers and brews in addition to Pro Monkey and his wife. Weather was great. I changed my ID It’s Marty. Blazer did a fantastic job pulling the trailer and TGlide.

[@RidersUnited]

Great video. Glad you sort this out. Now time for stage 2 or 3 😍

[@tgoodfella4290]

I like that you mention John maxwell from time to time. And you’re wearing his shirt I like it

[@DynojetResearch]

Awesome! Enjoy the ride 😎

[@terrymorgan4306]

Cool love the step up

[@Chaplain161]

Thanks for the tips and info.

[@williamb.9110]

I can't believe Rinehart can't make their 2-1 header clear the rear brake pedal. I had the same problem! If you install the aftermarket billet pedal from HD it's even worse. Finally I just yanked off the 2-1 and slapped on some V&H Short Shots. They fit with the brake pedal with lots of clearance on my 2020 Fat Boy. Thanks for the review! I have the SE-131 and CR512 Cam with PV widebands/Target Tune as well. I love it.

[@HarleyFatBoyJr]

Gotta love the 2-1 pipes. My TBRs are 💪🏾

[@HarleyFatBoyJr]

So informative bro. 🔥

[@CHEVYK10]

Nice been waiting on this video

[@GearsGadgets]

More to come!

[@HarleyFatBoyJr]

Damn sounds beastly

[@HarleyFatBoyJr]

Damn that bike sounds 💪🏾

[@HarleyFatBoyJr]

John is a beast

[@Seventurns9]

Great video. Thanks for all of the useful information. I have a '20 FLHC with Stage II and DynoJet PV-2B. I was wondering how the heck you ran the cable from the diagnostic port all the way to the handlebars to get it mounted so nice. It seems pretty impossible to route that cable through the backbone of the bike due to the size of the end connectors, and I really just want to get a few good Autotune sessions on it and done. Can I ask how you routed your cable and if it is permanent? Any problem with it too close to the heads? Thanks!!

[@JaySorsby1]

After I get my exhaust and cams squared away. I think that target tune is in my future.

[@mikescholtz9958]

Great video! I had the same issue and had to find all this out on my own…..but I do have a question for you about the Closed Loop Integrator….do you always ride with your bike with closed loop turned on?…..or do you do the auto tune with closed loop turned on and then flash the ECM with those changes made and then run open loop?

[@HarleyFatBoyJr]

Great share Fam 🤙🏾🔥

[@andrewvickers4487]

Thanks for sharing your experience, especially with the headers and the software settings. There is one thing I'm still unclear about when using stock headers. From what I can tell looking at the instructions for HD's 'M18 Oxygen Sensor Installation Tool' there's no need to get a new bung fitted, you just re-tap the stock one? (FYI I don't intend to pay hundreds for that OEM tapping kit!)

[@ejdtm]

Just wait until you add a cam. I’m guessing you just said to yourself, “I’m not adding a cam I’m happy with this”. Trust me you’ll add a cam. And you’ll absolutely love it. It’s a great bang for the buck. Anyways, the pipe sounds great and Baxter rules.

[@20sgcvo90]

Can you post or give all six settings you had to change I’m having the exact same problem thank you

[@mikecimorelli5071]

QUESTION: Im installing on mine now after watching this. What do I do with the Stock O2 sensors?

[@kevinmacwatters1519]

nice bike and video, subscribed today

[@GearsGadgets]

Thanks I appreciate it

[@HarleyFatBoyJr]

Is there a cam in the bike as well?

[@juanz7908]

I have the same motorcycle. Have you had any issues with the oil pump?

[@Heavy69Metal]

Are the O2 Sensors for Target tune same as the ones for the Screamin Eagle Street smart Pro Tuner wide band O2 sensors?

[@MrSuzukiyamaha]

I like the bags. Brand and model please? Factory?

[@danmulroy]

We’re you able to use a mac for all of this?

[@alvingallegos6367]

Thanks for the share in your struggles. Did you have any trouble with your terminal wire ends slipping out? I tried tinning them which didn't help. Later I tried temporary bung connectors with some solid wire and roughing them up which worked for a good while but every now and then I'd see a blinking light and reseated and retightened only to encounter it again after a few months, so got tired of that and went to ferruled connectors which seem to grab better only to find out (after ohm checking from the o2 sensor to terminal screws) the red wire on Bank 2 wasn't making contact at the plug connector. I'm still dealing with that but while searching for solutions I stumbled across Dynojet's o2 sensor replacement for $138 but found some Bosch one's for $30 each. When they arrive I'll let you know how they work. The cross reference matched as per Bosch along with other vehicle applications and by physical appearance. After I find out if they work, I will rip into the old sensor's plug and see if I can repair or destroy it. I'm waiting on Bryce to reply in case there is some simple thing I missed. Did you ever load a file from Dynojet which will configure your settings instead of setting it up? On mine I keep getting the popping exhaust so came off the dwell little by little but am getting close to the max I can back it off as per Dynojet's advice.

[@authorfalling]

how'd those bosch's work for you?

[@user-ob4nd6or1p]

Is there a way to connect the 18mm O2 sensors to my 2023 Road Glide without using the Target Tune?

[@user-lr6hb4ne5d]

Did going to wide band and target tune fix any motor heat issues.?

[@ihatesjws1188]

You still have to manually adjust AFR values for better performance. Target tune only adjust the VE tables so the calculations are correct. It is not making decisions to adjust AFR in different loads of the map.

[@shawn9878]

My understanding is it will work a couple of autotune runs? Then load those back into base map... Is that correct?

[@ihatesjws1188]

@@shawn9878 target tune will adjust VE tables as you ride to get the proper calculations to meet the AFR target for that particular load, rpm that is set in the ecm. It does have an option to Autotune and reload the new adjusted map. The main thing to remember is if the bike is set at 14.6 at 2000 rpms at 40kpa, neither system will change that, it will only adjust to hit that target.

[@shawn9878]

@@ihatesjws1188 thanks for the info, lots to learn .

[@sportglide5462]

hey what's up man, do you think these pipes will fit my low rider st ???

[@martinkies6580]

With the Target Tune can you choose the AFRs via throttle position and RPM?

[@jaynappierii1857]

What's the part number for the target tune

[@MrPAULONEAL]

I would like to see the install part in real time.

[@MarvFitBikesKicks]

This setup over Thundermax any day.

[@keitgwilliams4349]

When the F150 videos coming I been waiting for you big dawg

[@GearsGadgets]

My F150 has been sitting at the dealer for 30 days waiting in parts and is completely un-drivable. Waiting on parts / lemon law potentially to resolve. I had a ton of content planned for that truck but Fords quality control had other plans.

[@boxofmoles4057]

After you said, “DynoJet” my brain started hurting. Thanks for sharing, but yeah, no.

[@rtkl13]

So did you start with a down loaded flash or start tuning with what you had