Great video. Thank you !!!! One question, why not putting the check valve directly in the water port instead of the regulator ?
@Rduchene13714 күн бұрын
II think the same thing. A regulator with water (or corrosion in time) in it might not function properly. A 1/4' OD 1/8" NPT check valve directly into the waterport should be better. You could then keep water out of the regulator AND the compressor. As he shows it here, he is only protecting the compressor. However, there seems to be pretty limited availability of such a small check valve. The only one I see on Amazon has a review that it constricts airflow considerably because it's so small. you could probably connect an 1/8 male to 1/4" female into the water port and then the 1/4" check valve and then the 1/4NP press fit.
@Nessal832 жыл бұрын
I made a shower for $25 with a Harbor Freight 2 Gallon pressure sprayer and a sink sprayer head from home depot. It's simple, reliable, and cheap.
@MrBetoybrenda10 ай бұрын
I’m going to do the opposite…. Water pump in pelican case attached to non pressurized water port. Less problems !
@chrisridebike8 Жыл бұрын
Great setup but how I have mine mounted and the amount of tree branches that scrape along the sides of the truck, there’s no way that small air hose from the regulator to the push fitting would survive.
@jmmart4 Жыл бұрын
What the correct size for the straight fitting cause the link is bigger then what my water port has?
@marceld6061 Жыл бұрын
If using the Waterport for drinking water, make sure that any sealant you are using is safe to use for such a purpose.
@ravenrising Жыл бұрын
Not going to lie, the water explosion was the best part. Glad you smiled through it. GG
@HT79806 ай бұрын
Couldn’t you just use a digital regulator at the end of your air hose to just fill as needed?
@MikeMcQuitty5 ай бұрын
The straight fitting is a male 1/4 OD 1/8 NPT
@PerryAzevedo2 жыл бұрын
@chowcares - About to build this out myself. Why did you do the one-way valve before the regulator. Wouldn’t it make more sense to have that part as close to the WaterPort as possible?
@chowcares2 жыл бұрын
That’s the only place for the check valve. It’s there just incase water tries to go backwards into the compressor (which it shouldn’t).
@Rduchene13714 күн бұрын
II think the same thing. A regulator with water in it might not function properly. A 1/4' OD 1/8" NPT check valve directly into the waterport should be better. You could then keep water out of the regulator AND the compressor. As he shows it here, he is only protecting the compressor. However, there seems to be pretty limited availability of such a small check valve. The only one I see on Amazon has a review that it constricts airflow considerably because it's so small. you could probably connect an 1/8 male to 1/4" female into the water port and then the 1/4" check valve and then the 1/4NP press fit.
@kwelhand2 жыл бұрын
One of the channels! Excellent job as always.
@terouze2 жыл бұрын
What size push to connect fittings did you use? The link defaults to 1/4 but that's way bigger than the original fill valve
@eu4ian2 жыл бұрын
Did you figure out what the correct size for the replacement air intake fitting?
@MikeMcQuitty5 ай бұрын
The straight fitting is a Male 1/4 OD 1/8 NPT
@theoff-gridchurch82722 жыл бұрын
Always great content, you rock bro!
@chowcares2 жыл бұрын
I appreciate that!
@barrazafamily70102 жыл бұрын
Which mount do you have for your water port? I have mine connected to the hitch. But would much rather have it on my back tire!
@chowcares2 жыл бұрын
The same mount for the hitch. The arb bumper just so happens to have a 2”x2” reciever at the spare tire
@roamingmountaingoat54772 жыл бұрын
what makes the compressor come on and off? pressure switch? did you add that switch or its something that comes with the compressor?
@chowcares2 жыл бұрын
Comes with the compressor
@medolor2 жыл бұрын
👍🏽 good vid. What is RTV?
@chowcares2 жыл бұрын
Gasket maker, silicon
@omni_0101 Жыл бұрын
I want two weekenders, one for camp kitchen and one for shower. Should be easy enough to run the air hose through a splitter and keep both pressurized?
@snoboardnathan2 жыл бұрын
Great video! Check valve is a must! I didn't have one and wrecked my compressor.
@chowcares2 жыл бұрын
Oh no!
@reefermadnesstv3472 Жыл бұрын
I have a cheap but reliable Viar air compressor. Do I need an arb air compressor for this to work or any air compressor would work?
@TheVincent02252 жыл бұрын
Great job! Just have a question, how can I control the air compressure below 40 psi if I use the on board arb air compressor ? By keep reading the air regulator gauge? Thank you
@drew5301 Жыл бұрын
Chow! Can you do a video or give some details about your switch panel? Thank you!
@stevenlowrey6617 Жыл бұрын
Great video but the background music is bothersome.
@maisyray2 жыл бұрын
Love it. Glad you showed real life experience.
@tyler90561 Жыл бұрын
Thanks brother ordered all the parts from your list. Super helpful video. Patiently waiting for the parts to come in to do this mod
@tyler90561 Жыл бұрын
One issue I ran into is the push to connect valve that attaches to the waterport is no longer 1/4". I will order the 1/8" version to see if that works.
@TRDNate Жыл бұрын
This is awesome and a great idea
@Mr3DFJ2 жыл бұрын
Do you have a link to your water tank?
@Mr3DFJ2 жыл бұрын
NVM. googled it. Nice vid btw.
@chowcares2 жыл бұрын
Added a link in the description in case anyone else was wondering
@Trying8582 жыл бұрын
You do realize you are adding compressor oil to your water. This is a very bad idea.
@hjstrater2 жыл бұрын
Arb compressors are oil-less, I assume that’s what he’s got for onboard air.
@dynosaur52912 жыл бұрын
I wanted to reach you on instagram but its not valid?
@chowcares2 жыл бұрын
@aka_chowcares
@dynosaur52912 жыл бұрын
@@chowcares Thank you! Sent you a message on IG
@dicksuckman61222 жыл бұрын
Bro can you do a radiator replacement tutorial at some point for the Landcruiser?
@chowcares2 жыл бұрын
I actually replaced my radiator before I started this channel. It’s pretty straight forward I’m sure you’ll figure it out. If I break the radiator in the car again I’ll make a vid for sure
@dicksuckman61222 жыл бұрын
@@chowcares aight bro I gotchu
@AdventureTEQ2 жыл бұрын
I have one for the Radiator and T fittings over on my channel. Might help ya out.
@dicksuckman61222 жыл бұрын
@@AdventureTEQ you helped a lot man. The Koyorad I swapped in seems to be holding up pretty well so far