Ebay's $57 REMOTE CONTROLLED CUT OUTS - GOOD OR BAD??

[@TexasNova]

Part 2 here. All I can say is not GOOD. You'll have to watch to see for yourself kzbin.info/www/bejne/r2WQp2ChqMmjgs0

[@willygarcia4764]

Ok

[@renaissanceman7145]

I bought the 3" version & they now offer them in pairs with a hardwired switch. I don't want the possibility of losing the remote or it's battery dying at the worst moment. So far I'm impressed with them. If they crap out after very little use I'll come up with a way to control them with a cable.

[@TexasNova]

Renaissance Man - awesome man. The batteries will last for a good while imo. Just make sure you don’t over stress the motor. I believe this is where all the problems are. Should be 5 quick clicks of the remote from closed to open.

[@Theyayan28]

I didn't know Tom Segura was into car modding, dope!

[@heroichitsuji]

DUDE THATS TOTALLY TOM SEGURA

[@Ebone93]

Lol holy shit. Tripping out now.

[@Ebone93]

Segura? He isn't Japanese though 😂

[@Marshallarthurr]

@@Ebone93 I think he’s Asian not sure if Japanese

[@heyitsthatoneguy91]

i kinda want to put one on my work van lol

[@factorsknown]

Good investment for those new California laws

[@bstegmedia]

That's what I was thinking

[@Uizzj]

It's what the Aussies do.

[@TexasNova]

Noise restrictions?

[@tylanmcgee2124]

TexasNova new exhaust laws,, exhausts cant exceed 95 decibels, could get state reffed with a possible $1000 fine 🙄

[@Speedycory6]

That is why I am here! I’ve been ticketed 3 times since this new damn law!! 😑😑

[@HOTSHOT-ls1bc]

I got so excited looking for a hole exhaust but now I can get the best of both worlds and be quite when I want they already bitch about my radio but I’ll have something to drown them out now lmao

[@allmopars]

Cheaper ones the little flapper tends to warp causing rattling and leaks. Further back installed on cheap ones the longer they’ll last.

[@Brandon_Jackson]

On wish you can get them for $31 it’s called (2.5 header exhaust cutout. I ordered it on the 3rd of October and it says it’ll be here on the 21st of October. I hope it comes! Takes way toooo longgggg

[@TexasNova]

Brandon it’s always takes too long

[@unuesokami8736]

was it good???

[@xyloncamilleri2342]

I had this is my car, one broke as I got home, replaced with a new one and the same thing happened. The gears inside are very very weak and the small gear and the 2nd always break as there is no switch that cuts the power once fully opened or closed. The pulsating switch does the job but if you hold it lets say to close it as you can hear it leaking (no they dont close very good there will be a 1mm gap from both sides from which you will hear it leaking) and keep on trying to close it will break in a matter of seconds especially if its hot as it is part of the exhaust. Thumbs down for this

[@iSOBigD]

Can you confirm if you're able to weld them on with no leaks if the new pipe is the same diameter as the existing pipe? And I've seen videos where people did it without removing their existing exhaust pipes when welding it, would that not cause it to not be sealed properly?

[@brainjackson4020]

Can I put back the stock exhaust once I want to take it out and return the car

[@TexasNova]

These you can’t because you have to weld them in but there are some slip type exhaust clamps that you can

[@michaelcarranza8640]

Love your channel. Do they not make an option where it its just a flip of a switch? I much have a wired one rather than a key fob one. Also, are you worried about dead end part? I've heard it creates turbulence but I'm not sure if that really affects the performance or not.

[@TexasNova]

Mike they do have them that are on/off but they’re like $400 from what I’ve seen. As for turbulence ummm dunno. I couldn’t see it imo. It’s just a straight 100% dump out. If it’s a daily driver I wouldn’t be worried much about it.

[@mgrdigimarketing3035]

Awesome video dude. I think it says MILLION parts not MILLAN? Pity freight kills it for Chinese stuff outside USA a lot .

[@ossyali207]

Can the positive wire be connected straight to battery? Or does it have to be to the fusebox or something?

[@TexasNova]

Ossy yes it can be wired straight to the Battery. All you’d have to do is cut off the cigarette lighter plug-in and wire it in. I wouldn’t suggest it though. There is just something about leaving something that is connected to a constant “Hot” that worries me. What about your Cigarette Lighter?

[@uhhhhNick]

You could probably splice it into the accessory on wire. So when you turn your key to the on position it powers it up.

[@ossyali207]

Ah thanks for the replies guys... I understand what you mean, was abit worried which is why I asked. Was curious as my engine and battery are in the back and would have been simple to connect it straight to the battery instead of running a wire all the way to the front. Will wire a fuse in that case to make it easier. Thanks once again.

[@corypierce202]

What breaks them is the fact that they don’t auto open or close when you hit the button. You over work them when they reach their full movement. Even the expensive American made ones suffer from this. There is a video by Granatelli Motorsports talking about this. You might keep in mind not to over do it at it’s full open/close position

[@TexasNova]

Cory you’re absolutely right

[@Man_eee]

Do you know if the VACUUM ACTUATED EXHAUST CUTOUT's work better for this exact reason since those don't have a motor?

[@ksgarage3734]

Can you show how you ran the wires?

[@TexasNova]

Thanks for the Question! I haven't had the chance yet. The car is at the Paint shop right now. In 2 to 3 weeks i'll have it painted & then i'll have the Exhaust done. Sorry man couldn't tell you right now. But I will be doing a video for sure. Stay Tuned!

[@ksgarage3734]

TexasNova thanks for letting me know!

[@fear7962]

Hello I would like to buy one can I install in a Camry automatic ?

[@1flynlow]

where's the longevity update

[@TexasNova]

1flynlow - still giving a bit of time to get the feel for it. I can see some issues but nothing major. Still works like a champ. I’ll make one here shortly. Thanks for watching brother. 👍🏻

[@1flynlow]

subbed for update

[@TexasNova]

Part 2 here. kzbin.info/www/bejne/r2WQp2ChqMmjgs0

[@JeffLyle]

Do you have an update on how they are holding up? I'm thinking about throwing a pair of these on my Camaro. Thanks and great video!

[@TexasNova]

Jeff -So far so good. Main thing on these is make sure you don’t OVER STRESS the motors. These types here do not have a position stop. Thanks for asking & watching. 🤘🏻

[@nlerriorduno9772]

Over stress? Kinda new to this please explain

[@JeffLyle]

Gamagori Clowniac he means don’t hold the open or close button down too long. Once the valve is fully opened or fully closed, let go so it doesn’t burn out.

[@TexasNova]

Part 2 here. kzbin.info/www/bejne/r2WQp2ChqMmjgs0

[@joecuevas8840]

Can you show how you got them to run off one 12v? Or how you hot wired it to fuse box ? They said it has to be ran off 12v or it will burn the motor

[@TexasNova]

Thanks for the Question Joe! I'll be using this here ----> www.ebay.com/itm/152354048006 This will tie both of them together as one. Since these were sold as 1 & not as Pairs. As for wiring as "Hot" i'll say doubtful. Ignition Hot is sufficient enough. But I will be doing a video for sure.

[@joecuevas8840]

TexasNova thank you , what about hard wiring ?

[@TexasNova]

I am not sure what you're asking "Hard Wiring" Joe?

[@joecuevas8840]

In the video he says hard wiring to the fuse box. So you don't have to use up a 12v spot in the car

[@TexasNova]

I gotcha. There are several leads left over form my American Auto Wire that are Ignition Hot & Constant Hot. I really haven't decided on which direction that I am going to go. I am running low on 12v on my box like you said.

[@BillyFargon]

What's the butterfly diameter compared to actual exhaust?

[@TexasNova]

Thanks for the Question Billy! You know I didn't measure it. You'd think it would be the same size as the Pipe you're running. Cars in paint now so give me 2/3 weeks to find out for you & i'll leave you a comment here. Hope that helps man.

[@KINGBAND09]

Have you put them on?

[@TexasNova]

Yes right here. kzbin.info/www/bejne/eX6bZ4t3hrh3nck

[@popcornbutter9781]

Do you have the purchase link?

[@TexasNova]

The link is no longer available. Just do a search on Ebay "2.5 Electric Cut outs" From there you're all set

[@takchur1]

Hey TexasNova, any updates on this? Did the motor last?

[@TexasNova]

Brother I still am Jack Stand Racing. Spent a month getting parts for my transmission and still tying up loose ends to make it road worthy plus balancing family & work life & Nova Time is tough. I’ll get there brother. This last stretch to get it 100% done is killing me.

[@TexasNova]

Part 2 here. kzbin.info/www/bejne/r2WQp2ChqMmjgs0

[@cmoikahk4505]

Can it get wet? Like submerged?

[@TexasNova]

Yep. It’s all in closed

[@164hozey]

Did you get 2 or one?

[@TexasNova]

hozeyy I got two buddy.

[@theshark2804]

I am stuck between these or mr. Gasket manual cutouts. Need to get car 468 nova running first

[@waatao9856]

Update video when installed?

[@TexasNova]

wahh Taoo - here is the installed video you asked for. kzbin.info/www/bejne/eX6bZ4t3hrh3nck

[@iMakeKnviesFly]

This literally looks like cutouts from spelabs...

[@kevinrawatan4955]

what battery does the remote use?

[@TexasNova]

Kevinn maybe a 2025

[@ossyali207]

TexasNova Yep, that's right. It takes a single 2025 coin battery... Saw this earlier today and just brought the same battery. Works now ;)

[@dr.zackerysrichardsonm.d.3629]

Ummmm. Good or bad?

[@ossyali207]

Does the little box thats part of the wiring, need to be placed inside the car? Or doesn't it matter? Also cars looking awesome and coming together nicely in the new vids, good job.

[@TexasNova]

That box goes Inside.

[@sherazmalik2795]

Is it harmful for cars valves

[@TexasNova]

Sheraz Malik - No not at all.

[@sherazmalik2795]

@@TexasNova Ok Thanks

[@roar-films]

I want to install this on my Mustang GT which will require 2 of these. Is it possible to get one remote to make both cutouts function simultaneously?

[@TexasNova]

Yep right here. This will do the trick. www.ebay.com/itm/One-to-Two-Control-Wiring-Harness-Exhaust-Cut-Out-Muffler-Electric-Valve-Cutout-/223258110355?hash=item33fb386993

[@joachim8543]

how long did it last ?

[@TexasNova]

Man it works like a champ. It's really quiet & seals well with no leaks. The trick is not to STRESS the motor when opening & closing.

[@TexasNova]

Part 2 here. kzbin.info/www/bejne/r2WQp2ChqMmjgs0

[@Reaper81805]

They gonna raise the prices for Californians

[@DIYtryer]

Cool video, did you ever install these? how are they holding up?

[@TexasNova]

Part 2 here. kzbin.info/www/bejne/r2WQp2ChqMmjgs0

[@lonniehamilton914]

Great job I'm on it💪🔥.

[@onbeperkt2548]

ITS PATCHED

[@MrCJSherrill]

has it lasted?

[@TexasNova]

CJ unfortunately I have not installed it yet. The car is still in paint. I’ll definitely be doing a follow up to this video as soon as I get it installed. Stay tuned. 👍🏻

[@elizabethbrown8883]

@@TexasNova any update?

[@James-hg5tk]

TexasNova ?

[@tnfg6283]

TexasNova ?

[@TexasNova]

Here you guys go. Thanks for watching! kzbin.info/www/bejne/eX6bZ4t3hrh3nck

[@miguelfragoso7023]

How’s it holding up? I’m worried if they last.

[@TexasNova]

Miguel Fragoso - they’re not. I think they’re not designed for high flowing exhaust & stripped the gears

[@TheModAddict]

Woo hoo 400th subscriber..

[@TexasNova]

HorsePlay Motoring Ya know you’re right man. Lol far from the rest. Scratching & digging for every single one. Thanks for the Sub man!

[@TheModAddict]

TexasNova no problem..I just started my channel and its hard to keep content coming.. keep up the good work.

[@badlanz79]

BadlanzHPE. Made in the USA.

[@jamesh.7599]

Dems in 2018 thanks Trump lol

[@raybosflorida4928]

nobody shows how to install

[@mikeyvlogs9874]

Raybo sflorida take it to an exhaust shop

[@palmjc3872]

Great vid!

[@square1renovationsjoegiord298]

I put the same one on my Ram 1500 motor broke 3 months usage. Don't buy China made.

[@TexasNova]

Yikes man that stinks. I am running Quiet mufflers anyway & maybe going to run 1/4 open & leave it there when I get them installed. We'll see lol.

[@square1renovationsjoegiord298]

calvin6 c what's up brother!!!!

[@square1renovationsjoegiord298]

calvin6 are u on UCM UNDERDOGS OR BLACKLIST?

[@heyitsthatoneguy91]

cheap is cheap no matter where its from. you realize oem aftermarket parts are made all over, including china right?

[@mofine23]

Never underestimate the Chinese

[@TexasNova]

Right

[@Mybitterreality]

Good luck selling your car with a Road Worthy cert!

[@daroncraig8602]

You are going to want to red loctite the hardware on the flapper. Ask me how I know. Hahahaha

[@hiddeelbers78]

How do you know?

[@josem.penaloza3839]

Your video is awesome but your audio sucks bro. Fix it.

[@jorgeirizarry5971]

You bought the wrong one. This one is garbage.

[@TexasNova]

jorge irizarry - I think I pushed these to their limits with the exhaust flow.

[@jorgeirizarry5971]

@@TexasNova I use the black horse racing one. It's very cheap, good quality and you can connect two cut backs to the same power distribution box. It works fantastically.