Ebikeling Pedal Assist Sensor Installation

[@KirkHMiller]

I found out what was wrong with mine! I had it with the arrows going in the correct direction but it wouldn’t work- then I reversed the magnetic ring and backpedaled, then it started working. So now with both the sensor and the ring reversed it’s working!

[@mickyb.8014]

Fantastic video, thankyou so much!!! Funny how all the vids ive seen on installing a rear hub motor kit don't seem to mention anything at all about how to install the p.a.s sensor. I've watched a load and it made me totally forget all about this important part of the full kits installation. Hopefully I'll be fitting my Voilamart 1500w 48v rear hub kit tommorow (if a few more little things im waiting on delivery turn up?!?) Brilliant video, sooo appreciated as I'd started to get worried about how to fit the p.a.s.

[@josepha8759]

The part around 0:46 about removing the ring nut with the ring nut wrench went by way too fast.

[@bert-the-cosh7493]

I am struggling with the logic behind eBike assembly and your video has been a delight to follow. I subscribed because I can learn from you. I am English and often struggle with some American voices. Your voice is clear and easy to understand. Thank you!

[@zgabeartzaiftodie8615]

Hahahahaha you are English and often struggle with some American voices,you are so funny hahahahahahahaha!!!!

[@jtsotherone]

@@zgabeartzaiftodie8615 literally thousands of English videos have Americans saying 'OMG your accent is so hard to understand'.

[@marclavelle280]

Nothing to do with this video, but just wanted to thank you for the one some time ago, where you fitted Bafang battery UNDER the frame, on full sus. Would never have had the foresight/confidence to do it myself, without your help. But, the hours of pleasure I have had since doing it myself, with your expert guidance, deserve a very special THANK YOU, at the very least. Keep up the good work!

[@DoctorGeek1]

Thanks for this - I hadn't considered glueing, but it seems to be a common solution to my setup (with no ring nut).

[@andecap1325]

Mine came with disk that pulls apart and uses a lock ring that mounts on the outside groove to hold it together so you don't have to take off the crank! i found out the hard way after i tookoff the crank,pushed it on and it splilt in two...lol

[@ashlayconner9418]

Omg thank you! I've been going through hell trying to figure this out because my bike isn't set up like the instruction reference.

[@wildbsc]

Well presented young man answered my question about which way the arrows face thank you happy biking!

[@lauradrago33]

Quale è i modo giusto di mettere le freccette?

[@kassimrazack7602]

You almost answered all my questions I had, Good job mate. Thumbs UP👍👍👍👍👍👍

[@popcorne3]

Best tutorial I have come across, thank you!

[@markocomhr]

Hey glad you are making videos again!

[@2icelollys1goat]

I'm not! His Xiaomi scooter tyre change video left many feeling largely disgruntled. He addressed none of the comments aimed at him for giving the impression that the inner tube and tyre removal weren't anything other than a walk in the park to manage.

[@markocomhr]

Asphalt Ricky I changed the rear tyre without much sweat. The trick is to leave the tyre in hot water for awhile ;)

[@2icelollys1goat]

@@markocomhr Yeah I hear what you're saying. However.... the front is an entirely different 'animal' when it comes to things like undoing the nut, removing the inner tube, and mounting that tyre.

[@badenglish-member9785]

All these ebike manufacturers should make pedal assist that you don’t have to remove the crank pedal. It’s a freakin worse thing I’ve ever worked on bicycles.

[@soandsononame8750]

Takes a crank puller and 10 seconds

[@YkitzWorm]

@@soandsononame8750no it don’t I tried and apparently I got the wrong crank puller why not just 1 model

[@MartinLundström-l4v]

Old pedals often dont have any growes left, making extreamly painful

[@scootersdenver]

Extremely helpful. Thanks!

[@jorgea3507]

Thank you, great video. One question, My sensor is located on the sprocket side, (Zugo). What if the sensor spins freely? and slides in an out loosely? The teeth are not grabbing.

[@mark38699]

WARNING ⚠️ make sure you have a gap in between your crank arm and the magnet disc. You can break your bottom bracket If you don't have a gap. VERY IMPORTANT.

[@carstrucks9641]

Wtf are you talking about

[@JB_BLESSED]

I want to add a front hub motor kit to one of my e-bikes that runs totally independent from the original rear hub motor….can I add 2 pedal assist sensors at the same time?

[@hoosierdaddy9377]

Is it possible to instal a pedal assist on a one piece crank?

[@Edwardjonez]

thank you for your tips on how to install the sensor I like how you modify and make stuff work even though some designs differ on the crank. : )

[@waelkmail6133]

Can i add a front electric wheel to my rear assist e bike?

[@Juos10kustu]

ís it ok to make the hole bigger in the plastic magnet part ? my hole is too small

[@insideredgemma]

Thanks so much man I've been stuck for hours 💕

[@monicapatri9813]

I understand that this method only works in some frames. I had a carbon bike with the Aston Rider kit and I switched it to a bamboo bike in 10 minutes and I didn't have to cut any cables

[@chrisfreeman1093]

Hi I have a trike that's been converted to electric ,only the peddles are sealed and cannot be removed so how can I put a sensor to the peddle ,at the moment it's throttle only?

[@СергейНарушевич-б3т]

Вот это ты молодец! Так коротко и ёмко всё объяснил!

[@brolisimo]

I have got 4 wires coming from a controller, but only 3 on a PAS sensor? Does that mean PAS sensor is not compatible?

[@أمجدسوريا-ز3ي]

Hi does the arrow direction matter??

[@gamebros8424]

00:35 and 00:46 where do I get that tool and what is it called?

[@victoralejandro3460]

You did just great on this instructional video.

[@vsarsonas]

Question. Do you have a video about installing PAS to a hollowtech crank? I've been thinking changing from square tapered to hollowtech but I've no idea how and what parts do I have to buy. Thank you

[@BlankyLover9000]

But what do you connect the wire to?

[@velimir.l.georgiev]

Thanks for the video. What should be the whole length of the bottom bracket, when is 68mm?

[@allenmicheal8134]

Great how to, and mods! Thanks!

[@michaelnoardo3315]

im trying to configure my pas with my S866 controller and ESC brainpower 866 but my wheel has no Hall Sensor , i cannot make it work does PAS work with Motors with no HallSensor ? please someone helpme

[@johns2590]

The problem my bike shop said is that my Shimano crank is tapered and the PAS takes up room so that my crank are will not slide back on all the way, I can tighten the bolt but the crank is not seated all the way and the bike shop said it will eventually wear out the crank arm since it is not tightly seated. Is there a PAS system that will work in this case?

[@MK-sp2ln]

I have a question, why’d you point out while showing us the glueing method that it was not a ebikeling PAS? I’m asking because I have a ebikeling kit and was hoping to secure the sensor with the glue method

[@mrbivasroy]

Can I change my ebike fromsingle mode pedal assist to multi mode by any easy means?

[@rejarvaco3088]

There are 3 kinds of sensor for square type ,octalink and hallowtech pas sensor

[@Johnjones0151]

Thank you you made it very clear and easy I was not sure thanks again

[@cyberstar251]

what do i do if my bike has a single piece crank instead of the 3-piece one your bikes have?

[@mikesluyter5288]

I crazy glued my sensor to my BB with no lock ring

[@mikehutchinson6748]

I’ve installed this but my crank bolt keeps coming loose now every so often

[@Mantis858585]

Use a product called lock tight

[@rayleung1]

You have a video instruction on how to wire it to the controller?

[@monicapatri9813]

The comments are very good. I had my experience with the Aston Rider kit, it came out less than 260usd with lifepo battery and it has been running without problems since I had it more than a year ago

[@pinchertone]

this is a reallt interesting and usefull video. I did one of yours idea but I got a few mm too far from the sensor.. SO i'll be inspired to do something different

[@achzun4468]

3mm range between sensor n magnet rotor

[@enzodisciullo2557]

Are there no alternative sensors available to save pulling the crank off?

[@hhy2k]

There are...

[@flosa1995]

My sensor was too big to fit on the bearing plus there was no nut on the bearing So I just used silicone to fix it in place

[@szymontereshchenko7479]

Guten Abend . Und wie viele BESSERE Magnete sollte dieser Sensor haben!? Ich habe ein altes Fahrradmodell; / Es gibt KEINEN Bordcomputer, sondern lediglich eine kleine Platine mit LEDs. und sein natürlicher PAS-Sensor besteht aus nur 5 Magneten!!! / Heute sind es 8 und es sind immer noch 12 Magnete. Ist es also möglich, 5 durch 8 Magnete zu ersetzen? Was wird sich ändern!? Wird es später noch Probleme geben!? Danke .

[@kae4334]

how do you know what size to get, for a crank removal tool

[@ianmangham4570]

All standard size

[@conchubharbeats]

Tried number 3 first befor watching.if that fails.ill cut it and.attach it like you did on the second one, thankyou dude :)

[@johanswede8200]

Back again! Happy Swede here... Have you had any problems with your extra battery on Xiaomi m365 scooter? Should I do it? Put an extra battery...

[@DougHnut]

1000km on the extra battery, no problems. i have since sold the scooter to my coworker and he has had no problems as well. only bad thing is, with so much range, my feet start to hurt

[@johanswede8200]

@@DougHnut 👍💓

[@FireMinstrel]

Mine requires a hex key to remove the crank. 1/4-inch is too small and 3/8 is too big. :/

[@ianmangham4570]

Doh, it's obviously METRIC

[@hencloud]

Great video - thank you.

[@gediminasluksonis8329]

Hi, just a question because I am new with Ebikes and going to try to build one. Sooo if you have a throttle then you don't really need pedal assist sensor right?

[@Mantis858585]

Did you get an answer? Can i leave this off?

[@Goddi195]

Do I have to put on the pedal assist?

[@FilipWojnarowicz]

No

[@halfmoon9964]

Hey Doug, I was considering getting a 1500w ebikeling rear motor. Do you think it would be faster than the Bafang BBSHD or BBS02?

[@gadgetcaches5485]

Nice video, but I would have installed the sensor on top of the bottom bracket instead of beneath it to minimize dirt, mud, water getting to it.

[@hatzvegas]

Awesome! Thank you!

[@mark38699]

Fuck. I JB welded it on there and just realize it's 5 mm away. Can I bend the bracket towards it? The sensor will be at an angle.

[@baultourist2966]

Thanks from India

[@emecata3919]

Excellent

[@nozynoz]

Very helpful, straight to the point, cheers.

[@reallifegamer2448]

this helpt me very much, Than you!

[@MrStubbsj]

Just got in a bike conversion kit and had a sensor in it. based on the video we installed it wrong but I was wondering what exactly the sensor does?

[@aidanhengehold7326]

I too am going to be building a bike with my brother as something of a present, and thought I should answer your question. What it does, is when you pedal on your bike, it will start to engage the motor to assist you while you ride. That way you don't have to just hold a thumb/twist throttle to get the motor running. It is absolutely worth the fix if you intend on doing *any* pedaling. It just makes it so much more enjoyable. Hope that helps. Good luck.

[@brikka]

Well done! Thank you

[@fordmustanggt2046]

Thanks

[@hghmhgm]

Beautiful!!, thanks!

[@GregHarland1]

Thanks Doug

[@Fungai_funny]

How to turn off pedal assist

[@arthurperini]

Tks

[@Traderhood]

Thank you!

[@spacebar3119]

Hey Doug Hnut do you have a private email I have a request for you

[@freedomofmotion]

I used Blu tac 😂

[@davearduini]

first part: yes, second part: no

[@myrondesjarlait9752]

Nothing new here but thanx anyway.

[@sunnybeaches1331]

I dont see why these are necessary! Lol...

[@alwoeinzer5366]

У меня лучше получилось

[@leahdempsey9002]

What a load off waffle

[@jtsotherone]

in a 3min video with 3 different techniques shown? What were your expectations?

[@elestirmenelestiri4530]

Extremely helpful. Thanks!

[@Agzmoses]

Thanks